displaying 1000 best results Help
Search results for: crowd counting
-
Analysis of specific cutting resistance while cutting frozen pine blocks with narrow-kerf stellite tipped saws on frame sawing machines.
PublicationPrzedstawiono wyniki analizy oporów skrawania drewna zmrożonego podczas przecierania pryzm sosnowych na pilarce ramowej za pomocą cienkich pił. Badania prowadzono dla temperatur drewna -5 st. C, -20 st. C oraz dla porównania w temperaturze +18 st. C. Wilgotność drewna wynosiła 30%. Zaobserwowano znaczacy wzrost oporów skrawania wraz ze spadkiem jego temperatury.
-
Gdansk Bay sea bed sounding and classification of its results
PublicationThe main goal of this paper is to describe the results of sounding the Gdansk Bay sea bed by using a SES-2000 Standard parametric sub-bottom profiler. Quality of data obtained during trials depends inter alia on a proper location of transducer array to reduce influence of pitch, roll and heave motions as well as ship self noise (resulting from bubbles due to propeller and flow around hull, vibration generated by main engine and...
-
Frequency-dependent coupling model for microwave band-pass filter
PublicationThe goal of this work was to create a circuit model which represents frequency-dependent coupling between microwave resonators. Our models are designed for in-line filters. The frequency-dependent coupling enables one to realize a transmission zero which is not possible in classical approach with frequency independent inverters. In addition, the proposed model allows us to observe out-of-band behavior, e.g. spurious resonance....
-
Modified linear viscoelastic model of earthquake-induced structural pounding
PublicationIn recent times, earthquake-induced structural pounding has been intensively studied through the use of different impact force models. The numerical results obtained from the previous studies indicate that the linear viscoelastic model is relatively simple and accurate in modeling pounding-involved behavior of structures during earthquakes. The only shortcoming of the model is a negative value of the pounding force occurring just...
-
Multimodal coupling matrix for an array of rectangular slots on conducting cylinder
PublicationArtykuł prezentuje metodę wyznaczania sprzężeń wzajemnych pomiędzy aperturami promieniującymi położonymi na przewodzącym cylindrze. Pokazano sposób wyznaczania wielorodzajowej macierzy rozproszenia reprezentującej sprzężenia własne i wzajemne w badanej strukturze.
-
Superstable magnetic nanoreactors with high efficiency for Suzuki-coupling reactions
Publication -
Predicting the seismic collapse capacity of adjacent structures prone to pounding
Publication -
Shaking table experimental study on structural pounding during earthquakes
PublicationArtykuł przedstawia wyniki badań eksperymentalnych przeprowadzonych na stole wstrząsowym dotyczące zachowania się kolidujących ze sobą modeli konstrukcji podczas trzęsień ziemi. Wyniki te pokazują, iż zderzenia mogą prowadzić do znacznego wzrostu odpowiedzi konstrukcji, ale mogą mieć również pozytywny wpływ i częściowo wytłumić drgania. Ponadto, wyniki badań wskazują na istotny wpływ rodzaju materiału, z którego wykonane są elementy...
-
Predictive control of active filter system with LCL coupling circuit
Publication -
Coupling coefficients for the space group of the hexagonal close-packed structure
PublicationWe have computed the Clebsch-Gordan coefficients of the representations for the space group of the hexagonal close-packed structure for the points:V, A, H, K, L, M. We enumerate all arms of the wave vector stars and all wave vector selection rules.
-
Buckling of thin-walled columns accounting for initial geometrical imperfections
PublicationThe paper is devoted to the effect of some geometrical imperfections on the critical buckling load of axially compressed thin-walled I-columns. The analytical formulas for the critical torsional and flexural buckling loads accounting for the initial curvature of the column axis or the twist angle respectively are derived. The classical assumptions of theory of thin-walled beams with non-deformable cross-sections are adopted. The...
-
Detecting coupling directions with transcript mutual information: A comparative study
PublicationCausal relationships are important to understand the dynamics of coupled processes and, moreover, to influence or control the effects by acting on the causes. Among the different approaches to determine cause-effect relationships and, in particular, coupling directions in interacting random or deterministic processes, we focus in this paper on information-theoretic measures. So, we study in the theoretical part the difference between...
-
Seismic Pounding Between Bridge Segments: A State-of-the-Art Review
PublicationEarthquake-induced structural pounding in bridge structures has been observed in several previous seismic events. Collisions occur at the expansion joints provided between adjacent decks or between the deck and abutment. Pounding between the structural elements may lead to severe damages and even to the unseating of the bridge in certain cases. Several investigations have been performed to study pounding in bridges under uniform...
-
Pressure dependence of electron-phonon coupling inCe3+-dopedGd3Sc2Al3O12garnet crystals
Publication -
Computing algebraic transfer entropy and coupling directions via transcripts
PublicationMost random processes studied in nonlinear time series analysis take values on sets endowed with a group structure, e.g., the real and rational numbers, and the integers. This fact allows to associate with each pair of group elements a third element, called their transcript, which is defined as the product of the second element in the pair times the first one. The transfer entropy of two such processes is called algebraic transfer...
-
Local electrochemical impedance spectroscopy in dynamic mode of galvanic coupling
PublicationA novel method that combines local electrochemical impedance spectroscopy and mapping in dynamicmode is proposed. Method was validated over two galvanic couplings, namely zinc/copper and cad-mium/copper. Impedance spectrum response for all measuring points was obtained by means ofsimultaneous implementation of selected range of frequencies. Proposed method allows the measure-ment in a more time-efficient manner, at the same time...
-
Experimental Study on Pounding between Structures during Damaging Earthquakes
PublicationMutual pounding between structures during earthquakes may cause serious structural damage. The aim of this paper is to show the results of a shaking table experimental study focused on pounding between structures in series under several earthquake excitations. The experiments were performed using three tower models with different configurations and different gap distances between them. In the first stage of the study, one rigid...
-
Earthquake-induced pounding between superstructure segments of isolated bridge
PublicationThe use of seismic isolation in bridges is considered as one of the most promising advanced technologies to enhance the structural safety during earthquakes. However, the method results in larger displacements of superstructure segments increasing the probability of pounding between them. Reports after severe ground motions show that the earthquake-induced structural pounding may lead to significant damage in isolated bridges....
-
Coupling coefficients for the space group of the hexagonal close-packed structure
Publication -
Strong-coupling character of superconducting phase in compressed selenium hydride
Publication -
Simulations of impact force spectrum for earthquake-induced structural pounding.
PublicationCelem artykułu jest analiza możliwości zastosowanie tzw. spektrum siły zderzenia przy projektowaniu sąsiadujących ze sobą konstrukcji budowlanych na terenach sejsmicznych, w przypadku zbyt małej przerwy dylatacyjnej między nimi. W artykule przedstawiono wyniki symulacji numerycznych przeprowadzonych dla różnych wartości parametrów dynamicznych konstrukcji.
-
Non-linear viscoelastic modelling of earthquake-induced structural pounding
PublicationCelem artykułu jest analiza nieliniowego lepko-sprężystego modelu siły zderzenia, który ma zastosowanie do symulacji zderzeń pomiędzy konstrukcjami budowlanymi podczas trzęsień ziemi. Efektywność modelu sprawdzono poprzez porównanie wyników symulacji numerycznych z wynikami eksperymentalnymi. Wyniki pracy pokazują, iż w stosunku do innych modeli zderzeń, nieliniowy model lepko-sprężysty umożliwia najdokładniejszą symulację siły...
-
Eigenvalue approach to synthesis of prototype filters with source/load coupling
PublicationArtykuł przedstawia nową, szybko zbieżną, technikę syntezy macierzy sprzężeń filtrów o charaktrystyce Czebyszewa. Synteza opiera się na zastosowaniu metody najmniejszych kwadratów w odniesieniu do wartości własnych macierzy sprzężeń oraz jej podmacierzy.
-
Peak impact force for seismic retrofit of pounding-prone structures
PublicationCelem artykułu jest wykorzystanie dwuwymiarowych wykresów pokazujących wartość maksymalnej siły zderzenia (spektrów odpowiedzi) do wzmacniania odporności sejsmicznej budowli narażonych na zderzanie się podczas trzęsień ziemi. Wyniki analizy wskazują, iż wykresy takie mogą być bardzo przydatnym narzędziem przy podejmowaniu decyzji dotyczącej wyboru metody wzmacniania.
-
HMSE: A tool for coupling MODFLOW and HYDRUS-1D computer programs
PublicationA new software HMSE has been developed to facilitate external coupling between two well-known programs for subsurface flow modeling: MODFLOW-2005 (saturated zone flow) and HYDRUS-1D (unsaturated zone flow). Two coupling schemes have been implemented. In the first case the groundwater recharge flux is calculated by HYDRUS-1D assuming a fixed water table position and then passed to MODFLOW input files. In the second case the water...
-
Damage-Involved Structural Pounding in Bridges under Seismic Excitation
PublicationDuring severe earthquakes, pounding between adjacent superstructure segments of highway elevated bridges was often observed. It is usually caused by the seismic wave propagation effect and may lead to significant damage. The aim of the present paper is to show the results of the numerical analysis focused on damage-involved pounding between neighbouring decks of an elevated bridge under seismic excitation. The analysis was carried...
-
Experimental study on earthquake-induced pounding between steel structures
PublicationPounding between adjacent structures has been repeatedly observed during major earthquakes. The phenomenon may cause some local damage at the points of interactions, it may also lead to substantial destruction, permanent deformations or total collapse of colliding structures. The effects of earthquake-induced structural pounding have been studied for more than three decades now. However, most of the studies concerned masonry as...
-
Nitrofurazone Removal from Water Enhanced by Coupling Photocatalysis and Biodegradation
Publication(1) Background: Environmental contamination with antibiotics is particularly serious because the usual methods used in wastewater treatment plants turn out to be insufficient or ineffective. An interesting idea is to support natural biodegradation processes with physicochemical methods as well as with bioaugmentation with efficient microbial degraders. Hence, the aim of our study is evaluation of the effectiveness of different...
-
Predicting the seismic collapse capacity of adjacent structures prone to pounding
PublicationIn crowded cities, many structures are often constructed in a very close vicinity; therefore, during severe earthquakes, pounding phenomenon occurs due to out-of-phase vibrations of adjacent structures. In this study, pounding of adjacent structures is investigated up to the occurrence of total collapse. The novelty of this study is performing incremental dynamic analyses to compute the seismic collapse capacities of both pounding...
-
Pounding between high-rise buildings with different structural arrangements
PublicationEarthquake-induced structural pounding has led to significant damages during previous earthquakes. This paper investigates the effect of pounding on the dynamic response of colliding high-rise buildings with different structural arrangements. Three 3-D buildings are considered in the study, including 5-storey building, 7-storey building and 9-storey building. Three pounding scenarios are also taken into account, i.e. pounding between...
-
Facilitated transport of Zn(II), Cd(II) and Pb(II) ions trough polymer inclusion membranes with calix[4]-crown-6 derivaties
PublicationBadano transport mieszaniny równomolowych ilości jonów Zn(II), Cd(II) i Pb(II)z wodnej fazy azotanowej (cMe=0,001M) przez polimerowe membrany inkluzyjne(PIM) zawierające pochodne kaliks[4]korony-6 jako nośniki jonów. Badany był wpływ różnych podstawników na wydajność procesu. Selektywność transportu przez membrany zawierające jonofory 4 i 5 malała w kolejności Pb(II), Zn(II), Cd(II), natomiast z jonoforem 3 Pb(II), Zn(II)Cd(II)....
-
Studies on removal of Zn(II), Cd(II) and Pb(II) ions in polymer inclusion membrane transport with calix[4]-crown-6 derivatives
PublicationZbadano selektywność procesu wydzielania jonów cynku(II), kadmu(II) i ołowiu(II) z wodnych roztworów azotanowych zawierających równomolową mieszaninę tych trzech metali (cMe= 0,01 M) w procesie transportu przez polimerowe membrany inkluzyjne (PIM) przy użyciu w roli przenośników jonów pochodnych kaliks[4]-korony-6. Membrany typu PIM syntezowano z trójoctanu celulozy (nośnik), eteru o?nitrofenylopentylowego (pastyfikator) i pochodnych...
-
Investigation of poly(3,4-ethylenedioxythiophene) deposition method influence on properties of ion-selective electrodes based on bis(benzo-15-crown-5) derivatives
PublicationGlassy carbon electrodes modified by conductive polymers and membrane with derivatives of bis(benzo-15-crown-5) were tested as solid contact ion selective electrodes for K+ ions concentration determination. PEDOT with PSS, Cl- and ClO4- counter ions was electrochemically deposited onto glassy carbon substrates using four different electrochemical approaches (potentiostatic, galvanostatic, potentiodynamic and potentiostatic pulses)....
-
Traffic Type Influence on Performance of OSPF QoS Routing
PublicationFeasibility studies with QoS routing proved that the network traffic type has influence on routing performance. In this work influence of self-similar traffic for network with DiffServ architecture and OSPF QoS routing has been verified. Analysis has been done for three traffic classes. Multiplexed On-Off model was used for self-similar traffic generation. Comparison of simulation results was presented using both relative and non-relative...
-
Is It Right To Predict Cutting Forces On The Basis Of Wood Density?
PublicationSeveral properties of wood can be correlated to wood density. It is widely accepted that the cutting power requirements are following this general assumption. Therefore, according to classic literature sources available for determination of the cutting power for both band- and circular- sawing machines, the cutting power requirements (and/or cutting forces) are computed as a function of the wood specific gravity SG. It was shown...
-
Bio-based semi-aromatic polyesters for coating applications
PublicationLinear and branched bio-based semi-aromatic (co)polyesters were evaluated as resins for solvent-basedand powder coatings. Dimethyl-2,5-furandicarboxylate (DMF), 2,3-butanediol and various multifunc-tional comonomers were used to synthesize amorphous hydroxyl-end-capped (co)polyesters. The resinswere cross-linked using the -caprolactam blocked trimer of isophorone diisocyanate. Both the solvent-based and powder coatings proved to...
-
Reliable Anycast and Unicast Routing: Protection against Attacks
PublicationObecne sieci są przeważnie chronione przed awariami losowymi, a topologie sieci są w większości uznawane za regularne. Znane mechanizmy ochrony dotyczą typowo transmisji unicast (jeden-do-jednego). Jednakże w związku z obserwowaną konwergencją technologii/usług, inne odmiany transmisji (np. anycast - jeden-do-jednego-z-wielu) nabierają znaczenia. Co więcej, okazuje się, iż często awarie nie mają losowego charakteru, a topologie...
-
Traffic Type Influence on Performance of OSPF QoS Routing
PublicationFeasibility studies with QoS routing proved that the network traffic type has influence on routing performance. In this work influence of self-similar traffic for network with DiffServ architecture and OSPF QoS routing has been verified. Analysis has been done for three traffic classes. Multiplexed ON-OFF model was used for self-similar traffic generation. Comparison of simulation results were presented using both relative and...
-
Selected Multi-Criteria Green Vehicle Routing Problems
Publication -
Special Issue “Corrosion Resistance of Alloy and Coating Materials”
Publication -
Cooperative multi-provider routing optimization and income distribution
Publication -
The effect of heat treatment of hardwood on the specific cutting resistance
PublicationW pracy przedstawiono wyniki badań mocy skrawania podczas przecierania modyfikowanego i niemodyfikowanego termicznie drewna dębowego i jesionowego na pilarce ramowej PRW15M. W pierwszym etapie badań, graniakowe próbki drewna dębowego i jesionowego były modyfikowane termicznie za pomocą przegrzanej pary (temperatura 197C, czas 4 h) w parzelni wysokotemperaturowej, w warunkach przemysłowych. Następnie, wyznaczono właściwe powierzchniowe...
-
Accelerated ageing of organic coating systems by thermal treatment
Publication -
THE PROPERTIES OF NANOSILVER – DOPED NANOHYDROXYAPATITE COATING ON THE Ti13Zr13Nb ALLOY
PublicationThe aim of this research was to study the properties of nanohydroxyapatite (nanoHAp) and nanohydroxyapatite, doped with nanosilver (nanoHAp/nanoAg), coatings obtained by an electrophoretic deposition process. The suspensions was prepared by dispersing 0.1 g of HAp nanopowder for nanoHAp coatings and 0.1 g of nanoHAp and 0.025 g nanoAg for nanoHAp/nanoAg coatings. The deposition was carried out for 1 min at 50 V voltage followed...
-
Analysis of transverse load of saw in wood cutting process
PublicationW pracy przedstawiono przyczyny, rodzaje i efekty poprzecznego obciążenia zarówno pojedynczego ostrza, jak również wypadkowego obciążenia piły w procesie przecinania drewna. Dokonano rozkładu całkowitej siły odporowej na składową wolną- i szybkozmienną. Przedstawiono skutki wpływu poszczególnych rodzajów poprzecznego obciążenia pił na dokładność obróbki.
-
Mass and momentum conservation in the simplified flood routing models
PublicationW pracy wykazano, że uproszczone modele fal wezbraniowych w postaci fali kinematycznej reprezentują w przypadku liniowych zarówno zasadę zachowania masy jaki i pędu, natomiast w przypadku nieliniowym, reprezentują albo zasadę zachowania masy albo pędu, zależnie od postaci zachowawczej równania. Ponadto wykazano, iż nieliniowa fala dyfuzyjna nie spełnia ani całkowowej zasady zachowania masy ani pędu.
-
Selection of cutting and washing fluids as a method of waste minimization
PublicationW artykule przedstawiono wyniki testów korozyjności dla cieczy obróbkowych wykorzystywanych do produkcji przekładni skrzyni biegów. Testy prowadzono zgodnie z normami: DIN 51360-2 (Ford-test) oraz PN-92/M-55789. Badaniom poddano trzy ciecze obróbkowe oraz trzy ciecze chłodzące. Wraz ze spadkiem stężenia użytej cieczy, obserwowano większe ogniska korozji.
-
Peptidoglycans in cutting fluids – a good indicator of bacterial contamination?
Publication -
Survivability function - a measure of disaster-based routing performance.
PublicationZnaczenie przeżywalności sieci transmisji danych systematycznie rośnie, ponieważ awaria pojedynczego elementu może dotknąć miliony użytkowników na dużym obszarze. Zdefiniowano funkcję przeżywalności: prawdopodobieństwo realizacji określonego procentu strumieni użytkowników po awarii oraz atrybuty przeżywalności. Celem pracy było zbadanie wpływu protokołów doboru tras architektury TC/IP na funkcję i atrybuty przeżywalności. Pracę...
-
Sawing of wood - mechanics of cutting process, tools and machines.
PublicationW pracy przedstawiono wpływ obciażenia piły na dokładnośc przecinania. Zaprezentowano pilarkę ramową z eliptyczną trajektorią ruchu pił i hybrydowym dynamicznie wyrównoważonym napędem ramy piłowej, jak również wizyjny kontroler ostrzy pił tarczowych.