displaying 1000 best results Help
Search results for: HEATS
-
An advanced thermal-FSI approach of an evaporation of air heat pump
PublicationThe paper presents selected problems of numerical modeling of an advanced thermal-FSI approach of evaporator of air heat pomp. The example of a fin-tube evaporator has been studied, focusing on obtaining of heat exchanger characteristics applying two-phase flow model for the in-tube refrigerant flow. Special attention is given to heat transfer between separated medium for different air velocity and changed refrigerant mass flow...
-
Heat transfer characteristics of hybrid microjet – Microchannel cooling module
PublicationThe paper presents experimental investigation of heat transfer intensification in a microjet–microchannel cooling module. Applied technology takes benefits from two very attractive heat removal techniques. When jets are impinging on the surface, they have a very high kinetic energy at the stagnation point, also in microchannels boundary layer is very thin allowing to obtain very high heat fluxes. Main objective of this paper was...
-
Heat transfer characteristics of hybrid microjet -microchannel cooling module
PublicationThe paper presents the experimental investigation of heat transfer intensification in a microjet- microchannel cooling module. Applied technology takes benefits from two very attractive heat removal techniques. When jets are impinging on the surface, they have a very high kinetic energy at the stagnation point, also in microchannels boundary layer is very thin allowing to obtain very high heat fluxes. Main objective of this paper...
-
Investigation of the influence of capilary effect on operation of the loop heat pipe
PublicationIn the paper presented are studies on the inestigation of the capillary forces effect inducted in the porous structure of a loop heat pipe using water and ethanol ad test fluids. The potential application of such effects is for example in the evaporator of the domestic micro-CHP unit, where the reduction of pumping power could be obtained. Preliminary analysis of the results indicates water as having the best potential for developing...
-
Model of heat transfer in the stagnation point of rapidly evaporating microjet
PublicationThe paper presents investigation in the single water microjet surface cooling producing evaporating film. Reported tests were conducted under steady state conditions. It was proved that the phenomenon is similar to that of pool boiling. Results of experiments were compared with predictions by the model showing a good consistency.
-
Numerical study of turbulent flow and heat transfer of nanofluids in pipes
PublicationIn this work, Nusselt number and friction factor are calculated numerically for turbulent pipe flow (6 000 < Re < 12 000) with constant heat flux boundary condition using nanofluids. The nanofluid is modelled with the single-phase approach and the simulation results are compared with experimental data of Vajjha et al. [1]. Ethylene glycol and water, 60:40 EG/W mass ratio, as base fluid and SiO2 nanoparticles are used as nanofluid...
-
Performance of a plate heat exchanger operated with water-Al2O3 nanofluid
PublicationThis study is focused on experimental investigation of a selected type of brazed plate heat exchanger (PHEx). The main aim of the paper was to experimentally check the ability of nanofluids to enhance the performance of PHEx. A typical water-Al2O3 nanofluid was tested and compared to that of the base fluid, i.e. water. Nanoparticles were tested at the concentration of 0.1% and 1% by weight. Impact of the 1 day and 3 days break...
-
Modelling of the Heat Flux Density Distribution for Laser Beam Welding
PublicationGreat interest of the laser beam welding in industry is a new theoretical task, making planning the welding procedure specification and the quality control of welded joints easier. Estimating and calculating the dimensions of a weld pool and temperature distribution near weld mainly concern heat source modelling. In the presented work calculations of welding pool shape and thermal field for cylindrical-powered-normally model of...
-
Measurements of heat transfer enhanced by the use of transverse vortex generators
PublicationArtykuł dotyczy badań eksperymentalnych intensyfikacji wymiany ciepła w modelowym wymienniku ciepła z turbulizatorami przepływu dla różnej geometrii turbulizatorów. W badaniach zastosowano termografię ciekłokrystaliczną i cyfrową anemometrię obrazową.
-
Heat capacities and thermodynamic properties of antimony substituted lanthanum orthoniobates
PublicationThe results of heat capacity measurements for the lanthanum orthoniobate substituted with 10, 20 and 30 mol% of antimony (LaNb0.9Sb0.1O4, LaNb0.8Sb0.2O4 and LaNb0.7Sb0.3O4) are presented and discussed. Temperature dependence of low temperature heat capacity was analyzed within the Debye and Einstein models. The Debye temperature decreased, whereas the Einstein temperature increased with antimony content. The decrease of the Debye...
-
Performance of a plate heat exchanger operated with water-Al2O3 nanofluid
PublicationThis study is focused on experimental investigation of a selected type of brazed plate heat exchanger (PHEx). The main aim of the paper was to experimentally check the ability of nanofluids to enhance the performance of PHEx. A typical water-Al2O3 nanofluid was tested and compared to that of the base fluid, i.e. water. Nanoparticles were tested at the concentration of 0.1% and 1% by weight. Impact of the 1 day and 3 days break...
-
Heat calculations for water-cooled radiators of the inverter for induction heating
Publication -
Heat transfer enhancement through nanofluids with applications in automobile radiator
Publication -
The influence of air humidity on human heat stress in a hot environment
Publication -
A role of the heat and work uncompensatedtransformations in the balance of entropy and theturbomachinery efficiency
PublicationIn the paper we have presented a procedure of estimating a role of the uncompensated transformation of heat and work in ow of viscous and heat conducting uid. The procedure was introduced by Professor Romuald Puzyrewski and is essential in local, in time and space, balance of entropy. Furthermore this unique approach leads to redenition the eciency of uid-ow machinery in three-dimensional modeling using CFD (Computational Fluid...
-
Exergy analysis of the Szewalski cycle with a waste heat recovery system
PublicationThe conversion of a waste heat energy to electricity is now becoming one of the key points to improve the energy efficiency in a process engineering. However, large losses of a low-temperature thermal energy are also present in power engineering. One of such sources of waste heat in power plants are exhaust gases at the outlet of boilers. Through usage of a waste heat regeneration system it is possible to attain a heat rate of approximately...
-
Measurements of heat transfer enhanced by the use of transverse vortex generators
PublicationArtykuł dotyczy badań eksperymentalnych wymiany ciepła w modelowym wymienniku ciepła z turbulizatorami przepływu dla różnej geometrii turbulizatorów. Badania wykonano przy użyciu termografii ciekłokrystalicznej i cyfrowej anemometrii obrazowej.
-
Study of free convective heat transfer from horizontal conic.
PublicationPrzedstawiono teoretyczne rozważania i badania eksperymentalne konwekcji swobodnej od izotermicznej powierzchni poziomego stożka w przestrzeni nieograniczonej. Rozwiązanie przeprowadzono dla wprowadzonego krzywoliniowego układu współrzędnych, opartego na krzywej linii prądu wokół powierzchni stożkowej.
-
Beeswax And Palmitic Acid Utilization With Heat Pipes For Electronics Cooling
PublicationThis paper presents an experimental study of heat pipes supported by phase change materials (PCMs) coated at their adiabatic sections in application for electronics cooling. The PCMs investigated in this research were palmitic acid and beeswax, the latter being considered as a more cost-effective alternative. The study focused on three powers: 20W, 25W, and 30W. The experimental results revealed that the incorporation of palmitic...
-
Additive Manufacturing as a Solution to Challenges Associated with Heat Pipe Production
PublicationThe aim of this review is to present the recent developments in heat pipe production, which respond to the current technical problems related to the wide implementation of this technology. A novel approach in HP manufacturing is to utilise hi-tech additive manufacturing techniques where the most complicated geometries are fabricated layer-by-layer directly from a digital file. This technology might be a solution to various challenges...
-
Phosphorylation‐mediated regulation of heat shock response in Escherichia coli
PublicationEscherichia coli has two heat shock regulons under the transcriptional control of Esigma(32) and Esigma(E) RNA polymerases. These polymerases control the expression of genes, the products of which are needed for correct folding of proteins in the cytoplasm and the extracytoplasm respectively. In this study, we report that mutations in a tyrosine phosphatase-encoding gene led to decreased activity of these heat shock regulons. The...
-
Jeffreys heat conduction in coupled semispaces subjected to interfacial heating
PublicationA Jeffreys heat conduction problem for coupled semispaces subjected to the action of an interfacial heat source was defined. An analytical solution of the problem was derived for a polynomial specific power of the heat source using the Laplace transform approach. The asymptotic and parametric analysis was performed for different ratios of thermal conductivities , thermal diffusivities , thermal relaxation times and coefficients...
-
Selected studies of flow maldistribution in a minichannel plate heat exchanger
PublicationAnalysis of the state of-the-art in research of minichannel heat exchangers, especially on the topic of flow maldistribution in multiple channels, has been accomplished. Studies on minichannel plate heat exchanger with 51 parallel minichannels with four hydraulic diameters, i.e., 461 μm, 574 μm, 667 μm, and 750 μm have been presented. Flow at the instance of filling the microchannel with water at low flow rates has been visualized. The...
-
Thermal-Hydraulic Studies on the Shell-and-Tube Heat Exchanger with Minijets
PublicationIn this paper a patented design of a heat exchanger with minijets, with a cylindrical construction is presented. It is followed by the results of its systematic experimental investigations in the single-phase convection heat transfer mode. Based on these results, validation of selected correlations (coming from the literature) describing the Nusselt number was carried out. An assessment of the heat exchange intensification level...
-
Photovoltaic Roof Tiles: The Influence of Heat Recovery on Overall Performance
PublicationA photovoltaic (PV) roof tile serves both as a roofing material and as an electricity-producing surface. The main aim of the present study was to increase the overall system efficiency of PV tiles by using heat recovery. The chosen strategy was two-fold: determine the operational efficiency of PV tiles and optimize construction to increase the cooling effect when using air as the working medium. A detailed experimental study was...
-
Numerical analysis of high temperature minichannels heat exchanger performance
PublicationNowadays, the most difficult technological challenge in energy sector is connected with the gas micro-CHP units, dedicated to the distributed power generation. They are expected to be of high efficiency and at the same time of compact in size. Regarding the first reason, significant increase in microturbine efficiency can only be achieved by increase in the engine operating temperature. Therefore, one of the critical elements in...
-
Model of heat transfer in the stagnation point of rapidly evaporating microjet
PublicationThe paper presents investigation into the single water microjet surface cooling producing evaporating film. Reported tests were conducted under steady state conditions. Experiments were conducted using the nozzle size of 70 and 100 mikrometer respectively. In the course of investigations obtained were experimental relations between heat flux and wall superheating. It was proved that the phenomenon is similar to that of pool boiling...
-
Numerical Study of Turbulent Flow and Heat Transfer of Nanofluids in Pipes
PublicationIn this work, Nusselt number and friction factor are calculated numerically for turbulent pipe flow (Reynolds number between 6000 and 12000) with constant heat flux boundary condition using nanofluids. The nanofluid is modelled with the single-phase approach and the simulation results are compared with experimental data. Ethylene glycol and water, 60:40 EG/W mass ratio, as base fluid and SiO2 nanoparticles are used as nanofluid...
-
Zniszczenie korozyjne wymiennika ciepła = Corrosion failure of a heat exchanger
PublicationPłytowy wymiennik ciepła ze stali 316L uległ zniszczeniu po trzech latach eksploatacji, wskutek perforacji po czyszczeniu nieodpowiednim środkiem czyszczącym.
-
Convective momentum and heat transfer in single and two-phase flows
PublicationW pracy przedstawiono dorobek autora w zakresie modeowania wymiany pędu i ciepław w przepływach jedno i dwufazowych.
-
Physiological response of plants and cadmium accumulation in heads of two cultivars of white cabbage
PublicationRośliny z rodziny Brassicaceae są uważane za przydatne do celów fitoremediacyjnych w związku z tolerancją wysokich stężeń metali ciężkich, które mogą ulec hiperakumulacji w tkankach. Kapusta wydaje się rośliną, która może być wykorzystana jako fitoekstraktorw związku z dużą biomasą skoncentrowaną w główce i techniką uprawy tego warzywa umożliwiającą uzyskanie wysokiej wydajności. W doświadczeniu wazonowym badano reakcję sadzonek...
-
Changes in gene methylation patterns in neonatal murine hearts: Implications for the regenerative potential
PublicationBackground The neonatal murine heart is able to regenerate after severe injury; this capacity however, quickly diminishes and it is lost within the first week of life. DNA methylation is an epigenetic mechanism which plays a crucial role in development and gene expression regulation. Under investigation here are the changes in DNA methylation and gene expression patterns which accompany the loss of regenerative potential. Results The...
-
Cailiao Rechuli Xuebao/Transactions of Materials and Heat Treatment
Journals -
Process modeling inside cylinder in an internal combustion engine with heat regeneration
Publication -
Characterisation of the interfacial heat transfer coefficient in hot stamping of titanium alloys
Publication -
Molar volumes and heat capacities of electrolytes and iIons in N,N-dimethylformamide
PublicationZmierzono gęstości i molowe pojemności elektrolitów typu 1:1 oraz o soli o wyższych liczbach ładunkowych jonów w roztworach w N,N-dimetyloformamidzie w temperaturze 25 stopni Celsjusza. W oparciu o te pomiary wyznaczono standardowe objętości molowe oraz standardowe wartości izobarycznych ciepeł molowych. Uzyskane wartości podzielono na udziały jonowe wykorzystując tetrafenyloboran tetrafenylofosfoniowy (TPTB) jako elektrolit odniesienia....
-
Finding Temperature Distribution at Heat Recovery Unit Using Genetic Algorithms
Publication -
Experimental based determination of SCOP coefficient for ground-water heat pump
Publication -
Heat transfer and fluid flow visualization using liquid crystal thermography
PublicationW pracy przedstawiono możliwości wykrzystania termografii ciekłokrystalicznej do badań wymiany ciepła oraz wizualizacji pola przepływu w elementach urządzeń przemysłowych.
-
Reliability model of two-shaft turbine combustion engine with heat regenerator
PublicationW artykule przedstawiono możliwość zastosowania teorii procesów semimarkowskich do opisu niezawodności turbinowego silnika spalinowego. Opracowano model niezawodnościowy w formie siedmiostanowego procesu semimarkowskiego, umożliwiający określenie prawdopodobieństw przebywania silnika w stanie zdatności oraz wyróżnionych stanach niezdatności.
-
Critical Field and Specific Heat in Electron- and Hole-Doped Graphene Superconductors
Publication -
Asymptotic modelling and design of some microlayered functionally graded heat conductors
Publication -
Numerical single-phase modeling of turbulent flow and heat transfer of nanofluids
PublicationIn this work, Nusselt number and friction factor are calculated numerically for turbulent pipe flow (6 000< Re < 12 000) with constant heat flux boundary condition using nanofluids. The nanofluid is modelled with the single-phase approach and the simulation results are compared with published experimental data.
-
Plate heat exchanger with porous structure for potential use in ORC system
PublicationThe experimental analysis of passive heat transfer intensification in the case of plate heat exchanger has been carried out. The passive intensification was obtained by a modification of the heat transfer surface, which was covered by a metallic porous microlayer. The experiment was accomplished in two stages. In the first stage the commercial stainless steel gasketed plate heat exchanger was investigated, while in the second one...
-
Plate heat exchanger with porous structure for potential use in ORC system
PublicationThe experimental analysis of passive heat transfer intensification in the case of plate heat exchanger has been carried out. The passive intensification was obtained by a modification of the heat transfer surface, which was covered by a metallic porous microlayer. The experiment was accomplished in two stages. In the first stage the commercial stainless steel gasketed plate heat exchanger was investigated, while in the second one...
-
The Possibility to use a Nuclear Power Plant as a Source of Electrical Energy and Heat
PublicationIn this article issues concernig the possibility of nuclear power plant (NPP) operation also as a source of heat, which means combined heat and power production, have been described. CHP work is possible and profitable only in those areas where high thermal power demand occurs, which means near city agglomerations such as Warsaw or the Tri-City. Two levels of thermal power delivered to the heating system have been considered. Preliminary...
-
Microjet technology as a perspective intensification method for high performance heat exchangers
PublicationIn the paper two oryginal designs of compact heat exchangers with intensification effect produced by microjets are presented. The technology of microjets manufacturing is an "inhouse" patented design. The idea of such heat exchanger is shown together with the flow and thermal characteristics of the prototypes. The results of performer measurements are satisfactory and encourage for further research of the original designs.
-
Experimental study of boiling heat transfer in the stagnation point of water microjet
PublicationIn the paper presented is a comparison of computational model with experimental data. Numerical model of liquid film with phase change in the stagnation zone due to impingement of the microjet is more widely presented in authors previous work. The radius on which theevaporation process is taking place can be determined from the energy balance on the element of the plate. That radius has also been confirmed experimentally in the...
-
Effect of surface roughness on thermal-hydraulic characteristics of plate heat exchanger
PublicationIn the paper the experimental analysis of passive heat transfer intensification in the case of modeled plate heat exchanger is conducted. The plate heat exchanger is chosen for the analysis because this kind of heat exchangers could be prospectively applied in the ORC systems, however other areas or application are equally possible. The experimental setup was assembled at the Department of Energy and Industrial Apparatus of Gdansk...
-
A comparative study of different methods for heat transfer enhanced by the use of TVG
PublicationArtykuł dotyczy badań eksperymentalnych i numerycznych intensyfikacji wymiany ciepła w modelowym wymienniku ciepła z turbulizatorami przepływu dla różnej geometrii turbulizatorów. Do badań eksperymentalnych wykorzystano termografię ciekłokrystaliczną a modelowanie fizyczne wykonano za pomocą kodu komputerowego FLUENT.