Publications
Filters
total: 1026
displaying 1000 best results Help
Catalog Publications
-
Optimisation of turbine shaft heating process under steam turbine run-up conditions
PublicationAn important operational task for thermal turbines during run-up and run-down is to keep the stresses in the structural elements at a right level. This applies not only to their instantaneous values, but also to the impact of them on the engine lifetime. The turbine shaft is a particularly important element. The distribution of stresses depends on geometric characteristics of the shaft and its specific locations. This means a groove manufactured...
-
Heavy Duty Vehicle Fuel Consumption Modelling Based on Exploitation Data by Using Artificial Neural Networks
PublicationOne of the ways to improve the fuel economy of heavy duty trucks is to operate the combustion engine in its most efficient operating points. To do that, a mathematical model of the engine is required, which shows the relations between engine speed, torque and fuel consumption in transient states. In this paper, easy accessible exploitation data collected via CAN bus of the heavy duty truck were used to obtain a model of a diesel...
-
CAUSALITY IN MODELS OF THERMAL PROCESSES IN SHIP ENGINE ROOMS WITH THE USE OF BOND GRAPH (BG) METHOD
PublicationWith a single approach to modeling elements of different physical nature, the method of Bond Graph (BG) is particularly well suited for modeling energy systems consisting of mechanical, thermal, electrical and hydraulic elements that operate in the power system engine room. The paper refers to the earlier presented new concept of thermal process modeling using the BG method. The authors own suggestions for determining causality...
-
Discrete-continuous optimisation of an axial flow blood pump
PublicationThis paper presents results of discrete-continuous optimisation of an axial flow blood pump. Evolution Strategies (ES) are used as a global optimisation method in order to localise the optimal solution in relatively short time. The whole optimisation process is fully automated. This also applies to geometry modelling. Numerical simulations of the flow inside the pump is performed by means of the Reynolds-Average Navier-Stokes...
-
Technical and economic analysis of energy storage in the compressed air technology with low capacity for the production plant
PublicationCompressed air energy storage (CAES) system is a promising technology due to its numerous advantages, including relatively low maintenance cost, a long lifespan and high operational flexibility. This article explores the possibility of designing a CAES power plant as a source of electricity and heat for an existing industrial plant. The study involves the technical analysis of the power plant parameters and the economic analysis...
-
Mathematical modeling of hydrogen production performance in thermocatalytic reactor based on the intermetallic phase of Ni3Al
PublicationThe main goal of the following work is to adjust mathematical modelling for mass transfer, to specific conditions resulting from presence of chemical surface reactions in the flow of the mixture consisting of helium and methanol. The thermocatalytic devices used for decomposition of organic compounds incorporate microchannels coupled at the ends and heated to 500 oC at the walls regions. The results of the experiment were compared...
-
Experimental study on single phase operation of microjet augmented heat exchanger with enhanced heat transfer surface
PublicationThe article presents experimental investigations on a prototype heat exchanger. Presented research is focused on combined active and passive enhancement techniques of surface modification and microjet impingement. The results were compared to reference plate heat exchanger without microjet impingement. The Wilson plot method was applied to determine the heat transfer coefficients in the single phase operation. The heat exchanger...
-
The Experimental Determination of Bearings Dynamic Coefficients in a Wide Range of Rotational Speeds, Taking into Account the Resonance and Hydrodynamic Instability
PublicationMethods for the experimental determination of dynamic coefficients are commonly used for the analysis of various types of bearings, including hydrodynamic, aerodynamic and foil bearings. There are currently several algorithms that allow estimating bearing dynamic coefficients. Such algorithms usually use various excitation techniques applied to rotor–bearings systems. So far only a small number of scientific publications show how...
-
Experimental examination and modification of chip suction system in circular sawing machine
PublicationThe article presents the results of experimental examination of the wood chip suction system in the existing sliding table saw before and after its modifi cation. The studies focused on the extraction hood of the mentioned system. The methodical experimental research of the pressure distribution inside the hood during wood chip removal for the selected rotational speed of saw blades of 3500 and 6000 min-1 with a diameter of 300...
-
Local Nusselt number evaluation in the case of jet impingement
PublicationJet impingement still is one of demanding cases regarding computational fluid dynamics, due to its highly turbulent behaviour, with occurrence of turbulent-laminar transition. Even recently developed methods exhibit some drawbacks – RANS based simulations lack accuracy, LES and DNS based ones require too much computational time. Hybrid methods also exist, but their development and validation is in progress. Nevertheless, CFD application...
-
Prediction of flow boiling heat transfer data for R134a, R600a and R290 in minichannels
PublicationIn the paper presented is the analysis of the results of calculations using a model to predict flow boiling of refrigerants such as R134a, R600a and R290. The latter two fluids were not used in development of model semiempirical correction. For that reason the model was verified with present experimental data. The experimental research was conducted for a full range of quality variation and a relatively wide range of mass velocity....
-
Optimal boiling temperature for ORC installation
PublicationW pracy przedstawiono oryinalne kryterium wyznaczania optymalnej temperatury odparowania czynnika w obiegu ORC w postaci równań analitycznych. Pokazano przykład obliczeniowy na bazie R134a, wody i etanolu.
-
Thermodynamic analysis of the Compressed Air Energy Storage system coupled with the Underground Thermal Energy Storage
PublicationImprovement of flexibility is one of the key challenges for the transformation of the Polish Power System aiming at a high share of renewable energy in electricity generation. Flexible and dispatchable power plants will contribute to this ongoing transformation process as they compensate for fluctuations in electricity generation from renewable energy sources such as wind and photovoltaics. In this context, CAES storage tanks are...
-
Thermal and Hydrodynamic Phenomena in the Stagnation Zone — Impact of the Inlet Turbulence Characteristics on the Numerical Analyses
PublicationOne of the methods of heat transfer enhancement is utilization of the turbulent impinging jets, which were recently applied, for example, in the heat exchangers. Their positive impact on the heat transfer performance was proven, but many questions related to the origin of this impact are still unanswered. In general, the wall-jet interaction and the near-wall turbulence are supposed to be its main reason, but their accurate numerical...
-
Experimental Investigations on the Influence of Coil Arrangement on Melting/Solidification Processes
PublicationThe latent heat thermal energy storage units are very popular because of their high energy density and almost close to constant temperature during the charging/discharging. In the present study has been proposed new shell-and-coil geometry with a shifted coil position to enhance the performance of phase change thermal magazine. The experimental investigations have been performed both for the melting and solidification process of...
-
The Discrete-Continuous, Global Optimisation of an Axial Flow Blood Pump
PublicationThis paper presents the results of the discrete-continuous optimisation of an axial flow blood pump. Differential evolution (DE) is used as a global optimisation method in order to localise the optimal solution in a relatively short time. The whole optimisation process is fully automated. This also applies to geometry modelling. Numerical simulations of the flow inside the pump are performed by means of the Reynolds-Average Navier-Stokes...
-
Neoclassical Navier–Stokes Equations Considering the Gyftopoulos–Beretta Exposition of Thermodynamics
PublicationThe seminal Navier-Stokes equations were stated even before the creation of the foundations of thermodynamics and its first and second laws. There is a widespread opinion in the literature on thermodynamic cycles that the Navier-Stokes equations cannot be taken as a thermodynamically correct model of a local "working fluid", which would be able to describe the conversion of "heating" into "working" (Carnot's type cycles) and vice...
-
Analysis of the regenerative braking process for the urban traffic conditions
PublicationIn a regular drive system, with an internal combustion engine, vehicle braking is connected with the unproductive dissipation of kinetic and potential energy accumulated in the mass of the vehicle into the environment. This energy can constitute up to 70% of the energy used to drive a vehicle under urban conditions. Its recovery and reuse is one of the basic advantages of hybrid and electric vehicles. Modern traffic management...
-
A universal NDT method for examination of low energy impact damage in CFRP with the use of TLC film
PublicationThe article presents an attempt to use a sheet of laminated thermochromic liquid crystal film (TLC film) for non-destructive testing of the impact damage (energy values: 1J, 2J, 3J and 4J) in carbon fibre-reinforced polymer (CFRP). This is a new, alternative NDT approach based on the thermo-optical effect. The main advantages of this method are a) the low cost of TLC film, b) the low cost of recording devices due to the usage of...
-
Comparative analysis of thermodynamic cycles of selected nuclear ship power plants with high-temperature helium-cooled nuclear reactor
PublicationThis paper presents a comparative analysis of thermodynamic cycles of two ship power plant systems with a high-temperature helium- cooled nuclear reactor. The first of them is a gas system with recuperator , in which classical gas chamber is substituted for a HTGR reactor (High Temperature Gas-cooled Reactor) . The second of the considered cycles is a combined gas-steam system where working medium flux from gas turbine outlet...
-
Pressure drop related to flow maldistribution in a model minichannel plate heat exchanger
PublicationThe paper describes the issues related to the pressure drop that accompanies the phenomenon of maldistribution of working fluid between the channels of a model minichannel plate heat exchanger. The research concerns a single exchanger's plate containing 51 (in every geometry) parallel rectangular minichannels of hydraulic diameters 461 µm, 571 µm, 750 µm and 823 µm. In addition, the more complex geometry has been investigated,...
-
Calculation method for flow boiling and flow condensation of R134a and R1234yf in conventional and small diameter channels
PublicationThe paper presents the results of calculations performed using the authors’ model to predict the heat transfer coefficient during flow boiling for two refrigerants R134a and R1234yf. The experimental data from various past studies have been collected and the calculations have been conducted for the full range of quality variation and a wide range of mass velocity. The aim of the study was to test the sensitivity of the in-house...
-
A model of liquid film breakdown formed due to impingement of a two-phase jet on a horizontal surface
PublicationThe present work aims to provide an explanation to the phenomenon of breakdown of the thin liquid film created by impinging two-phase, liquid-gas jet. Existing in the literature models describe merely thebreakdown of single phase liquid films. The model presented here is based on examination of mass and energy equations under the applied criterion of the minimum of total energy. That allows to determinethe minimum thickness of...
-
Utilisation of bleed steam heat to increase the upper heat source temperature in low-temperature ORC
PublicationW pracy przedstawiono możliwość dogrzewu obiegu ORC za pomocą pary upustowej.
-
A Model of Thermal Energy Storage According to the Convention of Bond Graphs (BG) and State Equations (SE)
PublicationThe main advantage of the use of the Bond Graphs method and State Equations for modeling energy systems with a complex structure (marine power plants, hybrid vehicles, etc.) is the ability to model the system components of different physical nature using identical theoretical basis. The paper presents a method of modeling thermal energy storage, which is in line with basic BG theory. Critical comments have been put forward concerning...
-
The Influence of Loop Heat Pipe Evaporator Porous Structure Parameters and Charge on Its Effectiveness for Ethanol and Water as Working Fluids
PublicationAbstract: This paper presents the results of experiments carried out on a specially designed experimental rig designed for the study of capillary pressure generated in the Loop Heat Pipe (LHP) evaporator. The commercially available porous structure made of sintered stainless steel constitutes the wick. Three different geometries of the porous wicks were tested, featuring the pore radius of 1, 3 and 7 um. Ethanol and water as two...
-
Selected problems of determining an efficient operation standard in contemporary heat-and-flow diagnostics
PublicationW referacie wymieniono przyczyny powodujące niejednoznaczności i trudności wyznaczania wzorca sprawnej pracy turbinowych siłowni lądowych i morskich. Przeanalizowano dwie z tych przyczyn: obniżenie wartości parametrów dolotowych czynników roboczych oraz zmiany w konfiguracji połączeń pomiędzy urządzeniami składowymi obiegów cieplnych. Jako remedium na wynikające stąd trudności zaproponowano model obliczeniowy obiegu cieplnego o...
-
Turbulence models impact on the flow and thermal analyses of jet impingement
PublicationAccurate numerical reconstruction of heat and mass transfer processes in particular applications, such a jet impingement, is difficult to obtain even with the use of modern computational methods. In the proposed paper, the flow and thermal phenomena occurring during single minijet impingement on the flat, concave and convex, heated surfaces were considered. Problem of impingement on non-flat surface, still not common and purely...
-
Comparative study of flow condensation in conventional and small diameter tubes
PublicationFlow boiling and flow condensation are often regarded as two opposite or symmetrical phenomena, however their description with a single correlation has yet to be suggested. In the case of flow boiling in minichannels there is mostly encountered the annular flow structure, where the bubble generation is not present. Similar picture holds for the case of inside tube condensation, where annular flow structure predominates. In such...
-
Comparative study of flow condensation in conventional and small diameter tubes
PublicationIn the paper a method developed earlier by the first author is applied to calculations of heat transfer coefficient for inside tube condensation. The method has been verified using experimental data from literature on several fluids in different microchannels and compared to three well established correlations.
-
Comparative study of flow condensation in conventional and small diameter tubes
PublicationFlow boiling and flow condensation are often regarded as two opposite or symetrical phenomena. Their description however with a single correlation has yet to be suggested.In the case of flow boiling in minichannels there is mostly encountered the annular flow structure, where the buble generetion is not present. Similar picture holds for the case of inside tube condensation, where annular flow structure predominates. In such case...
-
Deformation and Surface Color Changes of Beech and Oak Wood Lamellas Resulting from the Drying Process
PublicationThe drying process was examined relative to parameters’ influence on the deformation and surface layer color changes of beech wood (Fagus sylvatica L.) and oak wood (Quercus robur L.). The goal was to analyze the impact of drying process conditions, wood and growth rings types, and load on the deformation and surface color changes of drying thin wooden elements. A further aim was to reduce the time of the lamella drying and minimize...
-
Application of Stirling Engine Type Alpha Powered by the Recovery Energy on Vessels
PublicationThe Stirling engine is a device, in which thermal energy is transformed into mechanical without a contact between the heat carrier, and the working gas closed in the engine. Mentioned feature makes this type of engine very attractive for the use of the recovery energy, taken from other heat devices. One of the potential applications of Stirling engines is the use of thermal energy generated in the ship's engine room for producing...
-
Porous structures in aspects of transpirating cooling of oxycombustion chamber walls
PublicationA wet oxycombustion chamber, which must be effectively cooled due to high temperature evolved during the oxy-combustion process, by using the phenomena of Reynolds thermal transpiration and Navier slip velocity. Closures needed to execute mass flow rate in a microchannel, which should be treated as a single porous structure in the walls of the combustion chamber, have been obtained by applying a local 3D approach. The Navier-Stokes...
-
Mitigation of the Flow Maldistribution in Minichannel and Minigap Heat Exchangers by Introducing Threshold in the Manifolds
PublicationIn the present paper, a detailed numerical investigation has been carried out to analyze the flow maldistribution in 50 parallel rectangular cross-section (1 mm depth and 1 mm width) minichannels and minigap section (1 mm depth and 99 mm width) with rectangular/trapezoidal manifolds in Z-type flow configuration. The author carried out numerical investigation with various mass flowrates, namely 0.05 kg/s, 0.1 kg/s and 0.2 kg/s which...
-
Thermal-Hydraulic Studies on the Shell-and-Tube Heat Exchanger with Minijets
PublicationIn this paper a patented design of a heat exchanger with minijets, with a cylindrical construction is presented. It is followed by the results of its systematic experimental investigations in the single-phase convection heat transfer mode. Based on these results, validation of selected correlations (coming from the literature) describing the Nusselt number was carried out. An assessment of the heat exchange intensification level...
-
Thermal and hydraulic phenomena in boundary layer of minijets impingement on curved surfaces
PublicationPresented work considers flow and thermal phenomena occurring during the single minijet impingement on curved surfaces, heated with a constant heat flux, as well as the array of minijets. Numerical analyses, based on the mass, momentum and energy conservation laws, were conducted, regarding single phase and two-phase simulations. Focus was placed on the proper model construction, in which turbulence and boundary layer modeling...
-
Design analysis of ORC micro-turbines making use of thermal energy of oceans
PublicationThe article presents the results of the analysis of energy conversion cycles making use of thermal energy of oceans. The objects of analysis were two cases of closed Organic Rankine Cycle (ORC) power plants, which were: the cycle in which the vapour of the working medium was produced by warm oceanic water in the circum-equatorial zone, and the so-called “arctic” cycle in which this vapour was produced by non-frozen water in the circumpolar...
-
Investigations on mixture preparation for two phase adiabatic pressure drop of R134a flowing in 5 mm diameter channel
PublicationThe article presents detailed two-phase adiabatic pressure drops data for refrigerant R134a. Study cases have been set for a mass flux varying from 200 to 400 kg/m2 s, at the saturation temperature of 19.4 ◦C. Obtained experimental data was compared with the available correlations from the literature for the frictional pressure drop during adiabatic flow. Influence of mixture preparation on pressure drop was investigated, for...
-
Model of heat transfer in the stagnation point of rapidly evaporating microjet
PublicationThe paper presents investigation in the single water microjet surface cooling producing evaporating film. Reported tests were conducted under steady state conditions. It was proved that the phenomenon is similar to that of pool boiling. Results of experiments were compared with predictions by the model showing a good consistency.
-
Model of heat transfer in the stagnation point of rapidly evaporating microjet
PublicationThe paper presents investigation into the single water microjet surface cooling producing evaporating film. Reported tests were conducted under steady state conditions. Experiments were conducted using the nozzle size of 70 and 100 mikrometer respectively. In the course of investigations obtained were experimental relations between heat flux and wall superheating. It was proved that the phenomenon is similar to that of pool boiling...
-
Particulate Matter Production of Small Heat Source Depending on the Bark Content in Wood Pellets
PublicationWood pellets as biofuel are more and more used in small heat sources in Europe. Standard wood pellets are produced from wood sawdust without bark. The paper deals about the impact of bark in wood pellets on their properties and combustion process. Special attention in this work is paid to production of particulate matter during combustion of wood pellets depending on bark content. There were experimentally produced spruce wood...
-
Experiences from operation of different expansion devices for application in domestic micro CHP
PublicationW pracy opisano doświadczenia zdobyte podczas badań trzech różnych urządzeń ekspansyjnych, możliwych do zaimplementowania w mikrosiłowni CHP. Przebadano ekspander wykonany na bazie sprężarki spiralnej oraz dwojakiego rodzaju silniki pneumatyczne. Wykazano "wyższość" maszyn pneumatycznych nad ekspanderem typu scroll, uzyskując sprawności wewnętrzne w zakresie 61-82%. Dodatkowo, mniejsza objętość i masa urządzeń pneumatycznych stanowi...
-
Design and investigations of a micro-turbine flow part
Publication-generative micro-power plant with the HFE7100 as a working medium was designed and built for experimental investigations. The heat output of the plant was assumed equal to 20 kW, while the electric output amounted to about 3kW.In the paper a multi-stage micro-turbine with partial admission of all the stages is described in detail and the results of the particular experimental investigations and numerical calculations are shown,...
-
Current Status, Barriers and Development Perspectives for Circular Bioeconomy in Polish South Baltic Area
PublicationThe following article presents the current legal situation in Poland as well as in the European Union. Data on biomass production in the Polish South Baltic area were analyzed, along with an indication of the key sectors for the development of bioeconomy. Presentation of the current state of biomass management was made and areas necessary for development were indicated to facilitate the sustainable management of biomass and waste...
-
A Theoretical and Experimental Study of Moderate Temperature Alfa Type Stirling Engines
PublicationThe Stirling engine is a device that allows conversion of thermal energy into mechanical energy with relatively high efficiency. Existing commercial designs are mainly based on the usage of high temperature heat sources, whose availability from renewable or waste heat sources is significantly lower than that of moderate temperature sources. The paper presents the results of experimental research on a prototype alpha type Stirling...
-
THE EFFECT OF WOOD DRYING METHOD ON THE GRANULARITY OF SAWDUST OBTAINED DURING THE SAWING PROCESS USING THE FRAME SAWING MACHINE
PublicationThe experimental results of the study focused on the effect of drying processes of warm air drying at the temperature of 6580°C and warm air-steam mixture drying at the temperature of 105°C of pine and beech wood to the size of sawdust grains created by cutting using RPW 15M frame saw is presented in the paper. Particle size analysis of dry sawdust was performed using two methods - screening method and optical method based on...
-
Extended duration running and impulse loading characteristics of an acoustic bearing with enhanced geometry
PublicationThis paper presents performance during prolonged running of the acoustic bearing when PZTs are switched off and when they are switched on. The effect of active PZT on shaft’s displacements in X and Y directions is clearly demonstrated. Performance of the acoustic bearing was also assessed when an impulse force was applied to the running shaft at speed. Once again the benefits of having PZTs active are beyond doubt. The instability...
-
AUGMENTATION OF THE CRITICAL HEAT FLUX IN WATER-Al2O3, WATER-TiO2 AND WATER-Cu NANOFLUIDS
PublicationThe main aim of the proposed study is therefore recognition of the phenomena accompanying nucleate boiling crisis of selected nanofluids during boiling on horizontal tubes of various outside diameters. Of particular interest is impact of contact angle and tube diameter on the value of critical heat flux. The results obtained should give more light on the nature of nucleate boiling crisis and will serve as a basis for future theoretical...
-
Flow structure, heat transfer and scaling analysis in the case of thermo-magnetic convection in a differentially heated cylindrical enclosure
PublicationThe experimental, numerical and scaling analysis in the case of thermo-magnetic convection in a thermosyphon-like enclosure filled with a paramagnetic fluid is presented. Visualization of temperature field together with the numerical simulation gave an information about the flow structure, which indicated “finger-like” structures of hot and cold streams advecting each other. Their number depended on the Rayleigh number and also...