Publications
Filters
total: 484
Catalog Publications
Year 2019
-
Pomiary skuteczności hamowania w stacjach kontroli pojazdów
PublicationPrzeprowadzono pomiary skuteczności hamowania w warunkach różnych stacji kontroli pojazdów. Celem przedsięwzięcia było porównanie wyników z uzyskanych pomiarów. Na tej podstawie pozyskano dane umożliwiające opracowanie założeń do koncepcji metodyki badań technicznych pojazdów zabytkowych w stacjach kontroli pojazdów.
-
Poroelastic Material for Urban Roads Wearing Courses
PublicationConventional road materials used for producing wearing courses of roads are based on mineral aggregate and bituminous or Portland cement binders. The road materials must be optimized for different properties, including skid resistance, durability, rolling resistance and tire/road noise. Unfortunately, it seems that within classic technologies it is very difficult to achieve further reduction of tire/road noise. Innovative porous...
-
Powder metallurgy of the porous Ti-13Nb-13Zr alloy of different powder grain size
PublicationThe objective of the present project was to determine the effects of powder granulation (fraction of grain size) for the Ti-13Nb-13Zr alloy, produced by powder metallurgy, on its porosity, grain cohesion, compressive strength, and Young`s modulus. Two powder fractions, 45–105 µm, and 106–250 µm were applied. The 50 mass pct of NH4HCO3 was added as a space holder. The specimens were in compaction stage uniaxially pressed at pressure...
-
The influence of inflation pressure and ambient temperature on the value of the truck tires rolling resistance
PublicationThe articlediscusses the effect of inflation pressure and the ambient temperature on the value of the rolling resistance of truck tires which directly translates into fuel consumption. For this purpose, a series of measurements was made at two ambient temperatures (at 25°C and -15°C), using different pumping pressures.
-
THEORETICAL AND EXPERIMENTAL INVESTIGATION OF THIN-WALLED BEARING SHELL’S DESIGN PARAMETERS AND ASSEMBLY CONDITIONS ON THE HOLDING TORQUE INSIDE A HOUSING BORE OF A CONNECTING ROD
PublicationThe aim of the work was the experimental and theoretical evaluation of the influence of the most important parameters determining the holding torque of a thin-walled bearing shell inside a housing bore of a connecting rod. The main investigated parameters were defned by authors experience in this feld. In the frst stage of research, a special test stand was designed in order to allow measuring the real values of the friction torque...
Year 2020
-
A literature survey of the influence of preform reheating and stretch blow molding with hot mold process parameters on the properties of PET containers. Part I.
PublicationThe hot fill process is an inexpensive conventional filling technology for high-acidity products (pH < 4.5). It allows certain drinks (sensitive beverages such as fruit and vegetable juices, nectars, soft drinks, vitaminized water) to be stored at ambient temperature without the need for chemical preservatives. The primary feature of the bottles used in the hot fill process is their temperature stability, i.e. the ability to retain...
-
A literature survey of the influence of preform reheating and stretch blow moulding with hot mould process parameters on the properties of PET containers – part 2.
PublicationThe hot fill process is an inexpensive conventional filling technology for high-acidity products (pH < 4.5). It allows certain drinks (sensitive beverages such as fruit and vegetable juices, nectars, soft drinks, vitaminised water) to be stored at ambient temperature without the need for chemical preservatives. The primary feature of the bottles used in the hot fill process is their temperature stability, i.e. the ability to retain...
-
Blowing Kinetics, Pressure Resistance, Thermal Stability, and Relaxation of the Amorphous Phase of the PET Container in the SBM Process with Hot and Cold Mold. Part I: Research Methodology and Results
PublicationThe technology of filling drinks without preservatives (such as fresh juices, iced tea drinks, vitaminized drinks) is carried out using hot filling. Mainly due to the production costs and lower carbon footprint, polyethylene terephthalate bottles, commonly called PET, are increasingly used in this technology. In this paper, the main aim is to describe the statistical analysis methodology of the influence of the temperature of the...
-
Blowing Kinetics, Pressure Resistance, Thermal Stability, and Relaxation of the Amorphous Phase of the PET Container in the SBM Process with Hot and Cold Mold. Part II: Statistical Analysis and Interpretation of Tests
PublicationThe technology of filling drinks without preservatives (such as fresh juices, iced tea drinks, and vitaminized drinks) is carried out using hot filling. Mainly due to the production costs and lower carbon footprint, polyethylene terephthalate (PET) bottles are increasingly used in this technology. In this paper, the main aim is to describe and interpret the results of statistical analysis of the influence of the temperature of...
-
Combined thrust radial bearing of a submarine main shaft – Design and analysis of failure
PublicationThis paper presents an analysis of the combined thrust radial bearing of a submarine propulsion shaft. The lubrication system of the bearing is based on a fixed ring. The efficiency of the lubrication system depends on the shaft speed and temperature, which affects oil viscosity. In turn, the thrust bearing load also depends on the rotational speed of the shaft, because as the speed increases, the drag of the ship increases simultaneously,...
-
Considerations about the applicability of the Reynolds equation for analyzing high-speed near field levitation phenomena
Publicationequation for analyzing near field levitation (NFL) phenomena. Two separate approaches were developed, experimentally verified, and applied to meet the research objective. One was based on the Reynolds equation and the other was based on general conservation equations for fluid flow solved using computational fluid dynamic (CFD). Comparing the calculation results revealed that, for certain operating conditions, differences in the...
-
Initial Field Validation of Poroelastic Pavement Made with Crumb Rubber, Mineral Aggregate and Highly Polymer-Modified Bitumen
PublicationTire/road noise in most driving conditions dominates other sources of traffic noise. One of the most efficient ways of reducing tire/road noise is to use the so-called “low noise pavement”. According to numerous studies, at present, poroelastic road pavement that is composed of rubber and mineral aggregate and polyurethane or bituminous binder gives the best noise reduction up to 12 dB. Unfortunately, there are many problems with...
-
Low noise poroelastic road pavements based on modified asphalt binder
PublicationTire/road noise is one of the most important environmental problems related to road traffic. As the most effective way to fight noise is reduction of sound emission from the source, a lot of work is being done to improve tire and road surfaces construction. This paper describes the first “road” results obtained within the SEPOR project, which is focused on developing a low noise poroelastic road surface based on bituminous binder....
-
Method of estimating the rolling resistance coefficient of vehicle tyre using the roller dynamometer
PublicationThe tendency in the past few years has been to introduce tyres with lower rolling resistance coefficients to the market. This paper presents a mathematical method for determining the rolling resistance coefficients variation depending on the speed. The method uses power balance which results from automobile dynamics while rolling on chassis dynamometer. The rolling resistance coefficients of tyres obtained through ‘drum test method’,...
-
Oscylacyjna metoda oceny oporu toczenia opon samochodowych na nawierzchniach drogowych o różnej teksturze i sztywności
PublicationOpór toczenia jest jednym z trudniejszych do wyznaczenia parametrów opon samochodowych. Jest to spowodowane tym, iż w przypadku nowoczesnych opon siła oporu toczenia odpowiada 0,5–1% obciążenia opony, dlatego pomiary bardzo małych sił muszą być wykonywane w silnie obciążonym układzie. Stanowi to ogromny problem, szczególnie w warunkach drogowych. Pomiary laboratoryjne są łatwiejsze do wykonania, ze względu na możliwość kontrolowania...
-
Poroelastic Material for Urban Roads Wearing Courses
PublicationConventional road materials used for producing wearing courses of roads are based on mineral aggregate and bituminous or Portland cement binders. The road materials must be optimized for different properties, including skid resistance, durability, rolling resistance and tire/road noise. Unfortunately, it seems that within classic technologies it is very difficult to achieve further reduction of tire/road noise. Innovative porous...
-
Stress Monitoring System for Individuals with Autism Spectrum Disorders
PublicationIn this article, a stress monitoring system tailored for individuals with Autism Spectrum Disorders (ASD) and developed for the educational institution is presented. People with ASD face problems with effective stress management due to their high self-perceived levels of stress, poor ability to cope with it, and dificulties with the accurate detection of the source of stress. Consistently, being able to measure stress appears to...
-
Test Stand for Multi-option Stretching of Soft Tissues
PublicationThe paper presents the genesis of the design and possibilities of the test stand for stretching soft tissues as well as examples of tests carried out on this device.
-
The Impact Of The Selected Parameters Of Fdm Manufacturing Technology On Tribological Performance Of Abs–Steel Pair Under Dry Friction
PublicationThe paper presents the result of tribological test of ABS and steel samples sliding under dry friction. Polymeric samples were manufactured of ABS material using FDM technology. Testing was carried out in unidirectional sliding in a ring-on-flat contact in a PT-3 tribometer. The scope of tested parameters included volumetric and mass wear, the friction coefficient, and polymeric specimen temperature. Polymeric specimens used in...
-
Wavelet Transform Analysis of Heart Rate to Assess Recovery Time for Long Distance Runners
PublicationThe diagnostics of the condition of athletes has become a field of special scientific interest and activity. The aim of this study was to verify the effect of a long (100 km) run on a group of runners, as well as to assess the recovery time that is required for them to return to the pre-run state. The heart rate (HR) data presented were collected the day before the extreme physical effort, on the same day as, but after, the physical...