Publications
Filters
total: 801
Catalog Publications
-
SHEAR YIELD STRESSES AND FRACTURE TOUGHNESS OF SCOTS PINE (PINUS SYLVESTRIS L.) ACCORDING TO THE RAW MATERIAL PROVENANCE
PublicationIn this paper values of the fracture toughness and of shear yield stress in the shear zone of Scots pine are presented. Tests of cutting were carried on samples of Scotch pine (Pinus sylvestris L.) wood of five provenances from Poland. These experimentally cutting tests were carried on the sash gang saw PRW-15M and the values of cutting power were obtained. The values of fracture toughness and shear yield stress based on Atkins’s...
-
EMPIRICAL ASSESMENT OF THE MAIN DRIVING SYSTEM OF THE CIRCULAR SAWING MACHINE
PublicationThe producers of panel saws tend to improve sawing accuracy and minimise a level of vibrations, to increase their competitiveness at the market. Mechanical vibrations in the main saw driving system, which level depend on a plethora independent factors, may really affect sawing accuracy and general machine tool vibrations. The objective of the research was to explore vibrations signals of the main spindle system, and to extract...
-
THE USE OF FEM FOR DETERMINATION OF RESONANT FREQUENCIES OF CIRCULAR SAW BLADES WITH INDIRECT TEETH IN GULLETS
PublicationUnderstanding the dynamical properties of the circular saw blade is necessary, since, there is a really need for a stable work at working rotational speeds, which are determined by frequencies at which the circular saw blade tends to vibrate. It was observed that the resonant frequency depend on the circular saw blade shape, a collar diameter and on saw’s teeth shape. In the presented work an attention was paid to the effect of...
-
Tests for lapping of flat surfaces of ceramic elements with forced dosing of abrasive slurry
PublicationPrzedstawiono zagadnienia dotyczące systemu wymuszonego dawkowania zawiesiny ściernej w docieraniu jednotarczowym powierzchni płaskich. Opisano zalety takiego systemu dozowania płynnej zawiesiny ściernej. Omówiono wybrane wyniki badań docierania elementów z ceramiki technicznej. Analizowano wpływ podstawowych warunków dawkowania zawiesiny na ubytek liniowy próbek.
-
Analysis of size and shape of abrasive micrograins in lapping of assembly joints
PublicationPrzedstawiono skomputeryzowana analizę wielkości i kształtu mikroziaren ściernych. W badaniach mikroziaren węglika boru, węglika krzemu i elektrokorundu zastosowano mikroskopie optyczna oraz specjalistyczne oprogramowanie MultiScan v.6.08
-
LOW PLACTICITY BURNISHING PROCESSES. Fundaments, tools and machine tools
PublicationW obszernej monografii (530 stron) autor przedstawił w sposób kompleksowy zagadnienia związane z wykończeniową metodą obróbki części maszyn przez powierzchniową obróbkę plastyczną-nagniataniem. Jest to pierwsza książka w języku angielskim poświęcona tej bezwiórowej i ekologicznej metodzie obróbki. W wielu przypadkach w technologii różnorodnych części maszyn i innych urządzeń, nagniatanie może zastąpić operację szlifowania. Ma to...
-
Study washboarding phenomenon in fame sawing machines
PublicationPraca dotyczy zjawiska washboarding cechującego się powstawaniem na piłowanej powierzchni sinusoidalnego profilu w przekroju poprzecznym i wzdłużnym. Wzór ten jest efektem drgań poprzecznych piły. Przedstawiono wyniki analiz teoretycznych oraz badań eksperymentalnych, w których wykazano, że zjawisko w przypadku pilarek ramowych jest efektem drgań wymuszonych brzeszczotu oraz regeneracji powstałej fali pierwotnej.
-
Circular saw teeth control with vision method
PublicationOpisano automatyczne urządzenie do automatycznego sprawdzania geometrii pił tarczowych WKOPTar. Określono błędy pozycjonowania ostrzy piły, której obrót jest sterowany w sposób automatyczny z wykorzystaniem obrazu ostrzy z kamery rejestrującej obraz powierzchni przyłożenia. Zaprezentowano szereg wyników pomiarów dokładności wykonania ostrzy piły.
-
Thickness monitoring of thin lamellae by optical measurement method
PublicationDo dnia dziesiejszego do pomiaru grubosci tarcicy używa się głównie suwmiarek. Celem projektu było opracowanie skanera, nie wymagajacego wysokich nakładów finansowych, do pomiarów grubości lameli po operacji rozpiłowywania drewna. Opracowany system jest zdolny do wykrywania elementów odbiegajacych od okreslonych tolerancji wymiarowych. zastosowano metodę pomiaru typu sandwich wykorzystująca 4 głowice laserowe. Wyazano, że przy...
-
Segmentation concept in mechanical engineering
PublicationZaprezentowano nowoczesne podejście do rozwiązywania problemów technicznych, technologicznych i organizacyjnych przedsiębiorstwa w oparciu ich strukturyzację. Przedstawiono przykłady segmentcji w stosunku do przedmiotów obrabianych oraz struktur organizacyjnych przedsiębiorstwa.
-
On some accuracy limiting factors in wood sawing
PublicationPrzedstawiono szczegółową klasyfikację czynników determinujących dokładność przecinania drewna piłami. Uwzględniono w niej również pozorną utratę dokładności wynikającą z anatomicznej budowy drewna i metody pomiaru (wykorzystywanie lasera). Występujące błędy przecinania zobrazowano szeregiem przykładów z badań doświadczalnych.
-
Wpływ parametrów docierania na jakość powierzchni powłok Cr2O3.
PublicationPrzedmiotem niniejszej rozprawy doktorskiej były badania wpływu wybranych parametrów docierania na jakość powłoki ceramiki Cr2O3. Analizowano wpływ wielkości ziarna, nacisków, prędkości i czasu docierania na wartości parametrów chropowatości powierzchni i ubytek liniowy powłoki ceramicznej nałożonej metodą plazmową na podłoże stalowe. Badania realizowano wg planowanego eksperymentu na docierarce jednotarczowej ze standardowym (pierścieniowym)...
-
Modelling and simulation analysis of process alternatives in the cellular manufacturing of axially symmetric parts [online]
PublicationAnalizowano procesy technologiczne (PT) alternatywnego wytwarzania określonego spektrum przedmiotów (PO) w zróżnicowanych systemach gniazdowych. Rozpatrzono warianty PT z operacjami zintegrowanej obróbki wiórowej kształtującej i obróbki wykańczającej poprzez nagniatanie, oraz wariantów z różnicowaniem operacji, w których obróbka wykańczająca realizowana jest w oddzielnych operacjach szlifowania. Dla potrzeb gniazdowej dekompozycji...
-
Design framework and simulation investigation of cellular parts manufacturing applications
PublicationPrzedstawiono koncepcję projektowania przebiegów grupowego wytwarzania asortymentu przedmiotów w systemach typu przepływowego, z wykorzystaniem algorytmu analizy podobieństwa ciągów znakowych, reprezentujących marszruty procesów, i jego oceny wg kryterium odległości Levenshteina, zgodnie z paradygmatem oszczędnej produkcji. Efektywność proponowanej metodyki weryfikowano symulacyjnie wg określonych scenariuszy, opisujących wariantowe...
-
System praktyk zawodowych na Wydziale Mechanicznym Politechniki Gdańskiej
PublicationReferat dotyczy studenckich praktyk zawodowych na kierunku kształcenia Mechanika i Budowa Maszyn Wydziału Mechanicznego Politechniki Gdańskiej. Przedstawiono w nim charakterystykę studiów, strukturę i programy praktyk oraz zasady ich organizacji. Praktyki zawodowe są ujęte programem studiów. Są obowiązkowe dla wszystkich studentów. Organizowane są w oparciu o wewnętrzny regulamin praktyk na podstawie umów zawieranych przez Wydział...
-
DFMA guidelines and a data base system in integrated development of hydraulic pumps
PublicationPrzedstawiono koncepcję budowy systemu decyzyjnego, dla zintegrowanego rozwoju pomp hydraulicznych oraz doboru adekwatnych technik wytworzenia komponentów i procesów montażu, z zastosowaniem metodyki SADT/IDEF0 oraz ogólnych wytycznych DFMA. Omówiono stosowane w przemyśle krajowym konstrukcje pomp zębatych z łożyskami tocznymi oraz udoskonalone rozwiązania projektowe tych pomp z łożyskami ślizgowymi (polimerowymi). Wskazano na...
-
Cut layer of a circular saw with radiaj run-out of cutting edges
PublicationW pracy przedstawiono analizę wpływu bicia promieniowego ostrzy piły tarczowej na zmianę nominalnego i całkowitego pola przekroju warstwy skrawanej.
-
Projektowanie strategii frezowania złożonych kieszeni w komponentach mechanicznych
PublicationPrzedstawiono metody wyznaczania optymalnych sekwencji narzędziowych w projektowaniu strategii frezowania złożonych kieszeni przy wykorzystaniu określonego zestawu narzędziowego. W doborze sekwencji dopuszczalnych uwzględniano eliminację sekwencji nieefektywnych. Alternatywne sekwencje narzędziowe modelowano w postaci ważonych grafów acyklicznych dla generowanych wariantów ścieżek kolejnych narzędzi, dokonując ich oceny kosztowej.
-
Multi-criteria Robot Selection Problem for an Automated Single-Sided Lapping System
PublicationFlat lapping is a crucial process in a number of precision manufacturing technologies. Its aim is to achieve extremely high flatness of the workpiece. Single-sided lapping machines have usually standard kinematic systems and are used in conjunction with conditioning rings, which are set properly be-tween the center and the periphery of the lapping plate. In this paper, instead of conventional single-side lapping machine, an automated...
-
Process layout planning and optimised product range selection in manufacture of wooden construction sets
PublicationThis paper introduces a systematic deterministic framework for planning and the analysis of facility layouts aimed at manufacturing a variety of parts, as components of specific end products. The essence of the proposed approach lies in the decomposition of a traditional job-shop into layout modules of generic material flow patterns, that inherently yields improved efficiency of the entire system. It entails the use of a relevant...
-
Influence of parameters of deep grinding on nanohardness and surface roughness of C45 steel
PublicationPrzedstawiono wyniki badań wpływu głębokości współbieżnego szlifowania powierzchni płaskich na chropowatość i nanotwardość warstwy wierzchniej stali C45 o strukturze ferrytyczno-perlitycznej i średniej wielkości ziarna 20 μm. Dla wszystkich wartości głębokości szlifowania uzyskano znaczny wzrost twardości warstwy wierzchniej przedmiotu obrabianego.
-
Structures of diamond tool composites
PublicationPresented are structures and examples of applications of diamond tool composites. They are widely used as cutting tools, bonded abrasive tools and dressing tools.
-
Kształtowanie właściwości warstwy wierzchniej podczas szlifowania
PublicationW artykule scharakteryzowano szlifowanie powierzchni płaskich połączone ze zmianami właściwości warstwy wierzchniej, zwłaszcza poprzez jej zahartowanie. Omówiono problemy związane z tzw. technologią grind-hardening. Dodatkowo przedstawiono badania, w których po procesie szlifowania uzyskano lepsze właściwości elementu obrabianego wskutek odkształcenia plastycznego.
-
Optymalizacja parametrów kinematycznych w docieraniu powierzchni płaskich
PublicationPrzedstawiono wpływ wybranych parametrów kinematycznych na geometryczne wyniki procesu docierania 1-tarczowego. W celu poprawy płaskości oraz jakości obrabianych powierzchni przeprowadzono optymalizację tych parametrów. Podstawowym kryterium optymalizacji jest równomierność zużycia narzędzia. Zaprezentowano wyniki symulacji, a następnie porównano je z wynikami badań eksperymentalnych.
-
Analysis of the design development of the sliding table saw spindles
PublicationProducers of sliding table saws constantly strive for improvement in sawing accuracy. One of the method is an upswing in a spindle behavior, since, it affects to a large degree sawing effects. The design development of sliding table saw spindles during the last quarter-century is presented. The spindle system of the modernized spindle of the sawing machine Fx550 is described.
-
THE EFFECT OF LOG SORTING STRATEGY ON THE FORECASTED LUMBER VALUE AFTER SAWING PINE WOOD
PublicationThe optimal transformation path for the resource is determined by the quality of a log combined with its dimension. The commercial value of derived products is also closely connected with the size and extent of containing wood deficiencies. The results of studies with three diverse strategies for log sorting are presented in the paper. Resource assessment by a worker without extensive experience in sorting logs, the certified grading...
-
New kinematic systems in single-sided lapping and their influence on lap wear
PublicationPrevious studies on one-sided lapping allow to state that not only parameters of lapping elements (i.e. properties of workpiece, abrasive grains and lapping plate) impact on a lapping efficiency. Influential are also kinematics and dynamics of the process. It is crucial to control an average velocity of lapping (v), a distribution of tangential acceleration (at), a nominal pressure (p), a lapping time (t) and disposal of workpiece...
-
Pure silicon recovering from photovoltaic modules
PublicationOdzyskiwanie krzemu ze zużytych lub uszkodzonych modułów fotowoltaicznych może mieć znaczenie nie tylko ekonomiczne, ale również ekologiczne. Etap obejmujący procesy chemiczne wymaga optymalizacji z punktu widzenia wymaganej czystości odzyskiwanego krzemu. W pracy przedstawiono wyniki przeprowadzonych prób trawienia poszczególnych warstw ogniw PV: warstwy antyodblaskowej, metalizacji (kontaktów), złącza p-n. Skład roztworów trawiących...
-
Forecasting values of cutting power for the sawing process of impregnated pine wood on band sawing machine
PublicationW artykule przedstawiono prognozowane wartości mocy skrawania dla pilarki taśmowej (ST100R firmy STENNER), które są stosowane w polskich tartakach. Wartości mocy skrawania oszacowano dla drewna sosny zwyczajnej (Pinus sylvestris L.), które zostało poddane impregnacji. Dla porównania wyznaczono również wartości mocy skrawania dla drewna niezaimpregnowanego. Wartości te określono za pomocą innowacyjnej metody prognozowania sił skrawania,...
-
Theoretical and Actual Feed Per Tooth During Wood Sawing on an Optimizing Cross-Cut Saw
PublicationThe work presents the geometries of circular saw teeth, whose task is to divide the cross-cut of the cutting layer. For efficient machining on a cross-cut saw with high feed speed values (about 1 ms−1) maximal theoretical feeds per tooth are determined. These values were compared with the actual values determined during transverse cutting of pine wood on a special test stands in industrial conditions. In the experiment the rotational...
-
The Effect of Circular Saw Blade Clamping Diameter on its Resonant Frequencies
PublicationIn this paper results of comparison of characteristic resonant frequencies of circular saw blades as a function of the saw clamping diameter from the impact test are presented. Obtained results revealed that proportionally with the increase of the saw clamping diameter also the dynamical stiffness of the saw blade increased. As a consequence of that the resonant frequencies of the saw blade move to higher values. Moreover, with...
-
Surface irregularities as a complex signal of tool representation together with uneven displacement in respect to the workpiece
PublicationIn a dynamic machining process, distortion in surface irregularity is a very complex phenomenon. Surface irregularities form a periodic representation of the tool profile with various kinds of disturbance in a broad range of changes in the height and length of the profile. To discern these irregularity disturbances, interactions of the tool in the form of changes perpendicular and parallel relative to the workpiece were analyzed...
-
Thickness accuracy of sash gang sawing
PublicationThin lamellae, corresponding to the layer components of structural glued members, i.e. 2-ply or 3-ply glued parquet, can be manufactured in re-sawing operations of kiln-dried wood blocks. These must be prepared with high dimensional accuracy and adequate surface quality following specific technical requirements for lamellae thickness variations, especially in the upper layers of the glued composite parquet. The accuracy of oak...
-
Modeling of Surface Roughness in Honing Processes by UsingFuzzy Artificial Neural Networks
PublicationHoning processes are abrasive machining processes which are commonly employed to improve the surface of manufactured parts such as hydraulic or combustion engine cylinders. These processes can be employed to obtain a cross-hatched pattern on the internal surfaces of cylinders. In this present study, fuzzy artificial neural networks are employed for modeling surface roughness parameters obtained in finishing honing operations. As...
-
Biocompatibility and Bioactivity of Load-Bearing Metallic Implants
PublicationThe main objective of here presented research is to develop the titanium (Ti) alloy base composite materials possessing better biocompatibility, longer lifetime and bioactivity behaviour for load-bearing implants, e.g. hip joint and knee joint endoprosthesis. The development of such materials is performed through: modeling the material behaviour in biological environment in long time and developing of new procedures for such evaluation;...
-
MACHINE VISION DETECTION OF THE CIRCULAR SAW VIBRATIONS
PublicationDynamical properties of rotating circular saw blades are crucial for both production quality and personnel safety. This paper presents a novel method for monitoring circular saw vibrations and deviations. A machine vision system uses a camera and a laser line projected on the saw’s surface to estimate vibration range. Changes of the dynamic behaviour of the saw were measured as a function of the rotational speed. The critical rotational...
-
Manufacturing and Recycling Impact on Environmental Life Cycle Assessment of Innovative Wind Power Plant Part 2/2
PublicationThe process of conversion of wind kinetic energy into electricity in innovative wind power plant emits practically no harmful substances into the environment. However, the production stage of its components requires a lot of energy and materials. The biggest problem during production plan-ning process of an innovative wind power plant is selection of materials and technologies and, consequently, the waste generated at this stage....
-
Influence of Honing Parameters on the Quality of the Machined Parts and Innovations in Honing Processes
PublicationThe article presents a literature review dealing with the effect of the honing parameters on the quality of the machined parts, as well as with the recent innovations in honing processes. First, an overview about the honing and the plateau-honing processes is presented, considering the main parameters that can be varied during machining. Then, the influence of the honing parameters on surface finish, shape deviation and material...
-
A Critical Reanalysis of Uncontrollable Washboarding Phenomenon in Metal Band Sawing
PublicationThe article analyzes the cutting process of hard bars. Investigations conducted in industrial conditions demonstrated the presence of surface errors in the machined workpieces in the form of washboard patterns. The purpose of this study was to analyze the results of cutting on band sawing machines with different band saw blades. The cutting processes were conducted on three different horizontal band sawing machine types. Analyzed...
-
Report for the Short Term Scientific Mission within COST Action FP1101: development of the in-field sensor for estimation of fracture toughness and shear strength by measuring cutting forces
PublicationKnowledge on the fracture properties of materials is essential to assure structural integrity and proper design of mechanical connections in timber constructions. Measurement of this property is, however, a very challenging task. The linear fracture mechanics is usually used for its assessment assisted with experimental data acquired by means of various techniques, usually of destructive nature. The cutting force is an energetic...
-
Hardened Steel Surface Waviness Created by Rolling Burnishing Process
PublicationThe surface of the finishing machined parts is defined mainly by roughness parameters. Growing demands on the part, especially mating sliding or rolling, require the specification of additional parameters, such as waviness parameters, particularly when there is significant resistance to seizing or noise reduction. This paper presents surface waviness characteristics of hardened burnished steel.
-
The Roughness of the Hardened Steel Surface Created by the Rolling-Burnishing Process
PublicationBurnishing hard materials can be used as an alternative finishing process. this paper presents the results of burnishing hardened steel. The article discusses surface deformation that occurs during this process and depends on the selected parameters of the geometric structure of the force applied for surface burnishing.
-
Fracture Toughness and Shear Yield Strength Determination for Two Selected Species of Central European Provenance
PublicationWhen offcut of wood is formed by shearing, Atkins’s analyses of sawing processes can be applied. Using this modern approach, it is possible to determine the fracture toughness and shear yield strength of wood. This model is only applicable for the axial-perpendicular cutting direction because both of these parameters are suitable for the given direction of cutting edge movement and cannot be considered material constants. Alternatively,...
-
Problems of Flaking in Strengthening Shaft Burnishing
PublicationThe article presents the results of testing the surface condition of shafts manufactured by a strengthening rolling burnishing process. The shafts with a hardness about 220 HB were burnished with a roller with different force. Researches were carried out with particular attention to the structure of the outflowing material in the tool zone during burnishing process. The article presents the results of the examinations of burnished...
-
A BRIEF REVIEW AND COMPARISON OF SELECTED EXPERIMENTAL METHODS FOR MEASURING NATURAL FREQUENCIES OF CIRCULAR SAW BLADES
PublicationDifferent methods for the empirical determination of the natural frequencies of circular saw blades are presented. Stationary methods, such as the harmonic and impulse tests, are discussed and the results of related comparison are given. The comparison of the methods revealed their degree of practical usefulness and their accuracy in determining natural frequencies. A combination of specific methods is proposed, which should allow...
-
Multi-objective optimization of tool wear, surface roughness, and material removal rate in finishing honing processes using adaptive neural fuzzy inference systems
PublicationHoning processes are usually employed to manufacture combustion engine cylinders and hydraulic cylinders. A crosshatch pattern is obtained that favors the oil flow. In this paper, Adaptive Neural Fuzzy Inference System (ANFIS) models were obtained for tool wear, average roughness Ra, cylindricity and material removal rate in finish honing processes. In addition, multi-objective optimization with the desirability function method...
-
A pilot study to assess manufacturing processes using selected point measures of vibroacoustic signals generated on a multitasking machine
PublicationThe article presents the method for the evaluation of selected manufacturing processes using the analysis of vibration and sound signals. This method is based on the use of sensors installed outside the machining zone, allowing to be used quickly and reliably in real production conditions. The article contains a developed measurement methodology based on the specific location of microphones and vibration transducers mounted on...
-
A pilot study to assess an in-process inspection method for small diameter holes produced by Direct Metal Laser Sintering
PublicationPurpose The purpose of this research is to evaluate the geometric quality of small diameter holes in parts printed by DMLS technology. An in-process optical inspection method is proposed and assessed during a pilot study. The influence of the theoretical hole diameter assumed in a CAD system and the sample thickness (hole length) on the hole clearance was analysed. Design/methodology/approach The samples made of two different...
-
Experimental examination and modification of chip suction system in circular sawing machine
PublicationThe article presents the results of experimental examination of the wood chip suction system in the existing sliding table saw before and after its modifi cation. The studies focused on the extraction hood of the mentioned system. The methodical experimental research of the pressure distribution inside the hood during wood chip removal for the selected rotational speed of saw blades of 3500 and 6000 min-1 with a diameter of 300...
-
Cylindrical surface irregularities presented by frequency spectra of relative tool displacement to the workpiece
PublicationW pracy przedstawiono częstotliwościowe składowe nierówności powierzchni toczonych. Ponieważ nierówności mają charakter szerokopasmowy, trudny do wartościowania parametrami normatywnymi, zastosowano ich analizę amplitudowo-częstotliwościową, opartą na szybkiej transformacie Fouriera. Zaproponowano oryginalny układ pomiaru sygnału przemieszczeń narzędzia względem przedmiotu dla charakteryzowania nierówności wzdłużnych. Dla generowania...