Wyszukiwarka
Filtry
wszystkich: 297
wybranych: 254
Wyniki wyszukiwania dla: CONCENTRICALLY BRACED FRAME
-
Buckling of frame braced by linear elastic springs
PublikacjaIn the design codes and specifications, simplifed formulae or diagrams are given for determining the buckling lengths of frame columns based on the ruling criterion of considering frames as sway or non sway. Due to the fact that, the code formulae utilize onlylocal stifness distributions, these formulae may yield in certain cases rather erroneous results. In most code formulas a case of weakly braced frames is usually not considered.In...
-
Seismic Response Analysis of Knee-Braced Steel Frames Using Ni-Ti Shape Memory Alloys (SMAs)
PublikacjaShape Memory Alloys (SMAs) are known as active materials that can be widely used for structural purposes due to their flag-shape behavior under loading and reloading. Their unique characteristics provided a potential solution for civil engi-neers especially to model buildings with the capability of dissipating seismic en-ergy. In this study, the main purpose is to explore the seismic behavior of Knee-Braced Frames (KBFs) and...
-
Seismic performance evaluation of steel buckling-restrained braced frames including SMA materials
PublikacjaThe permanent deformation of the building after seismic excitations can be determined by the Maximum Residual Interstory Drift Ratio (MR-IDR), which may be used for measuring the damage states. Low-post yield stiffness of the steel buckling-restrained braced frame (BRBF) makes this system vulnerable to large MR-IDR after a severe earthquake event. To overcome this issue, this paper investigates the seismic limit state performances...
-
Buckling of braced frames
PublikacjaIn this paper the classical Winter model, developed originally for columns is applied for frame structures and compared with the results of parametric study of frame with bracing. Sensitivity analysis of critical loads of frame due to bracing stiffness is carried out and the threshold bracing stiffness for full bracing is found. In the non-linear statical analysis the forces in bracings are calculated.
-
Timber frame houses resistant to dynamic loads - seismic analysis
PublikacjaThe aim of the article is to present results of seismic analysis results of two real-sized timber frame buildings subjected to seismic excitations. The first model was insulated with mineral wool, the second one with polyurethane foam. Technology and specifications involved in both models construction is based on the previously conducted experimental research on timber frame houses, including wall panels tests, wall numerical models...
-
Timber Frame Houses with Different Insulation Materials - Seismic Analysis
PublikacjaThe aim of this article is to present results of a dynamic numerical analysis focused on the response of two timber frame building structures exposed to seismic excitations. The first structure was insulated with mineral wool, while the second one with polyurethane foam. Specifications and technology involved in the models' construction are based on the previously conducted experimental study, upon which numerical structural models...
-
MODAL ANALYSIS OF REAL TIMBER FRAME HOUSES WITH DIFFERENT INSULATION MATERIALS
PublikacjaThe aim of this article is to present the results of a numerical modal analysis of two actual structures of timber frame buildings and the different behaviour due to the used insulation material. One model of the timber structure was filled with mineral wool, while the other with polyurethane foam. During the modal analysis, eigenvalues for both models have been determined. The results of the analysis clearly show the increase...
-
Experimental dynamic study on a timber-frame house using shaking table
PublikacjaThe aim of this paper is to show the results of the shaking table experimental study concerning the behaviour of the model of the timber-frame house under earthquake excitation and impact loading. In order to determine the basic dynamic properties of the undamaged structure, the free vibration and the sweep-sine tests were first conducted. Then, the model was excited using the time history record of the El Centro earthquake of...
-
Granulometric characterization of Arctic driftwood sawdust from frame sawing process
PublikacjaArctic driftwood can be used as an alternative source of wood as construction timber and furniture material, especially in Iceland and Greenland. The use of Arctic driftwood can help in the fight against climate change, by developing land reforestation processes and reducing the volume harvested wood from forests and sustainability of harvesting processes. In this paper the results of an analysis of the effect of long-term residence...
-
Nonlinear numerical simulation of earthquake-induced pounding between timber frame buildings
PublikacjaEarthquakes may induce serious dynamic loads acting on buildings, which can lead to damage or even destruction of the whole structure. In densely populated areas, it is quite common that buildings are located very close one to another which can result in pounding between them during ground motions. Due to the environmental awareness, multi-story timber frame buildings are gaining popularity and therefore there is a need to investigate...
-
The Effect of Openings’ Size and Location on Selected Dynamical Properties of Typical Wood Frame Walls
PublikacjaThe wooden frame constructions are now popular in many developed countries of the world. Many of these locations where such buildings are constructed are exposed to seismic and other shocks which are generated by human activities. This paper discusses the effect of the size and location of openings in the wooden frame walls under dynamic loadings. Natural frequencies of such frames with and without openings have been determined....
-
Analysis of Validation and Simplification of Timber-Frame Structure Design Stage with PU-Foam Insulation
PublikacjaThe transition from experimental studies to the realm of numerical simulations is often necessary for further studies, but very difficult at the same time. This is especially the case for extended seismic analysis and earthquake-resistant design. This paper describes an approach to moving from the experimental testing of an elementary part of a wood-frame building structure to a numerical model, with the use of a commercial engineering...
-
Increasing the Seismic Resistance of Wood-frame Buildings by Applying PU Foam as Thermal Insulation
PublikacjaWood-frame buildings are very common in regions that are exposed to earthquakes. Most of residential buildings are constructed using this technology; therefore, the seismic resistance of them is really essential in order to prevent human losses and structural damage. The aim of the present article is to show the results of the detailed numerical FEM analysis focused on the seismic behaviour of the wood-frame house with different...
-
Modeling of wood frame structures with different insulation materials under damaging dynamic loading
PublikacjaWood frame buildings are very popular in regions that are exposed to different dynamic excitations, such as damaging earthquakes. Their seismic resistance is really important in order to prevent structural damages and human losses. This paper presents the results of advanced numerical investigation carried out using the FEM. Based on the models of wall panels, the numerical model of real structure of the wood frame building has...
-
Activities of the Astro-geodetic Observatory in Jozefoslaw in the frame of IGS and EUREF
PublikacjaThe Astrogeodetic Observatory of the Institute of Geodesy and Geodetic Astronomy of the Warsaw University of Technology (WUT) in Jozefoslaw was incorporated in 1957. In 1991 it joined the International GPS Service (IGS) and started to operate as a permanent in 1993. Since then the following permanent services have been maintained: GPS observations using Trimble and Turbo Rogue receivers, tidal gravimetric observations with LaCoste&Romberg...
-
Stability and load bearing capacity of a braced truss under upward wind loading
PublikacjaThe paper is focused on the numerical and experimental investigation of stability of a steel truss under upward wind loading. The structure was stiffened by elastic braces situated at the top and bottom chord. Usually the lateral (translational) brace stiffness is considered. However, the rotational stiffness of braces caused by interaction between torsional stiffness of the truss top chord and bending stiffness of the roof elements...
-
Stability and load bearing capacity of a braced truss under upward wind loading
PublikacjaThe paper is focused on the numerical and experimental investigation of stability of a steel truss under upward wind loading. The structure was stiffened by elastic braces situated at the top and bottom chord. Usually the lateral (translational) brace stiffness is considered. However, the rotational stiffness of braces caused by interaction between torsional stiffness of the truss top chord and bending stiffness of the roof elements...
-
Window frame integrable air recuperation minichannel/minigap heat exchanger
PublikacjaThis article describes an evaluation of mini heat exchangers operation as a decentralized mechanical ventilation system with recuperative heat recovery that can be integrated into the window frame. The relatively small yet efficient air recuperation system allows for retrofitting existing buildings by reducing the overall energy consumption and thus the CO2 emissions. The proposed design, unlike existing systems, is easy to scale...
-
Implementation of the EVRF2007 height reference frame in Poland
Publikacja -
Hybrid dynamically balanced saw frame drive
PublikacjaW pilarkach ramowych, w których rama piłowa jest napędzana poprzez mechanizm korbowy, generowana przez ramę piłową siła bezwładności oddziaływuje na fundament pilarki oraz na jej układ napędowy. W niniejszym artykule przedstawiono sposób eliminacji tych niekorzystnych zjawisk. Autorzy zaprezentowali dynamicznie wyrównoważony hybrydowy układ napędu ramy piłowej, w którym występuje akumulator energii kinetycznej przyłączony równolegle...
-
Study washboarding phenomenon in frame sawing machines
PublikacjaPraca dotyczy zjawiska washboarding cechującego się powstawaniem na piłowanej powierzchni sinusoidalnego profilu w przekroju poprzecznym i wzdłużnym. Wzór ten jest efektem drgań poprzecznych piły. Przedstawiono wyniki analiz teoretycznych oraz badań eksperymentalnych, w których wykazano, że zjawisko w przypadku pilarek ramowych jest efektem drgań wymuszonych brzeszczotu oraz regeneracji powstałej fali pierwotnej.
-
Multiple reference frame theory in the synchronous generator model considering harmonic distortions caused by nonuniform pole shoe saturation
PublikacjaThe paper describes a synchronous generator model developed based on the multiple reference frame theory. The main physical phenomena included in the model are the machine armature non-sinusoidal voltage waveform and the influence of armature current in load conditions on the armature voltage waveform higher harmonic components. The modified multiple reference frame theory model is proposed. In this modified theory model the field...
-
Timber-frame house resistant to dynamic loads - analysis of wall panel filled with polyurethane foam
PublikacjaThe present study shows the experimentally and numerically determined response of a single timber-frame house wall panel filled with polyurethane (PU) foam under dynamic loads. The harmonic tests were conducted for the following frequencies: 0.5 Hz, 1.0 Hz, 2.0 Hz and 5.0 Hz for various values of the specified displacement. Based on the results of the comparison between the experimental tests and the numerical analyses, the numerical...
-
Influence of effective width of flange on calculation and reinforcement dimensioning of beam of reinforced concrete frame
PublikacjaThe paper analyses the influence of modelling the cross-section of a beam in two-storey reinforced concrete frame of industrial warehouse with dimensions: 18.0 m × 32.0 m using bar elements on the results of bending moments, the value of elastic deflection and the dimensioning of reinforcement due to bending. Six options were considered: a beam as a rectangular section and five T-beam variants with different definitions of effective...
-
CONSTRUCTION TECHNOLOGY OF TIMBER-FRAME HOUSES RESISTANT TO DYNAMIC LOADS – STUDY ON MODELS OF EXTERIOR WALLS
PublikacjaThe aim of this paper is to show the numeric representation of experimental studies concerning the behaviour of exterior wall models of a timber-frame house under harmonic loading. A single wall model according to traditional technology of timberframe house walls (filling with mineral wool) was tested. The analysis was conducted for the following frequencies: 0.5 Hz, 1.0 Hz, 2.0 Hz and 5.0 Hz for various values of the specified...
-
Comparison of the fracture toughness of pine wood determined on the basis of orthogonal linear cutting and frame sawing
PublikacjaIn this paper, the values of the fracture toughness of Scots pine determined by cutting tests are presented. The cutting tests were carried out using the samples of Scotch pine (Pinus sylvestris L.) from Pomeranian Region, Poland. These experiments were carried out on two research stands: orthogonal linear cutting tests were conducted using the microtome instrument and the frame saw PRW-15M was used for sawing tests. The values...
-
Numerical Analysis of a Steel Frame Building with Soft-storey Failure under Ground Motion Excitation
PublikacjaThe aim of this paper is to show the results of a numerical analysis focused on the behaviour of multi-storey steel frame building that suffers from a soft-storey failure under ground motion excitation. A numerical model of the structure was created in FEM computer software and was exposed to an impact that would have been generated after a soft-storey failure due to falling of the upper floors. During the analysis, the whole structure...
-
Analysis of surface roughness of chemically impregnated Scots pine processed using frame-sawing machine
PublikacjaThe objective of this work was to evaluate the effect of the impregnation process of pine wood (Pinus sylvestris L.) on roughness parameters of the surface processed on a frame sawing. The samples weredried and impregnated using a commercial procedure by a local company. The touch method withthe use of measuring stylus (pin) was employed to determine of surface roughness of the samplesconsidering parameters, namely, arithmetical...
-
Understanding of Dementia in the Polish Language: A Frame Semantic Approach
Publikacja -
Formation of novel nanostructures using carbon nanotubes as a frame
Publikacja -
Frame sawing machines for accurate wood re-sawing
PublikacjaPrzedstawiono zwięzłą historię pilarek ramowych. Zaprezentowano ekologiczne i ekonomiczne zalety pilarek ramowych nowej generacji. Opisano podstawowe cechy układów kinematycznych nowoczesnych pilarek ramowych oraz podano ich podstawowe dane techniczne.
-
THE EFFECT OF WOOD DRYING METHOD ON THE GRANULARITY OF SAWDUST OBTAINED DURING THE SAWING PROCESS USING THE FRAME SAWING MACHINE
PublikacjaThe experimental results of the study focused on the effect of drying processes of warm air drying at the temperature of 6580°C and warm air-steam mixture drying at the temperature of 105°C of pine and beech wood to the size of sawdust grains created by cutting using RPW 15M frame saw is presented in the paper. Particle size analysis of dry sawdust was performed using two methods - screening method and optical method based on...
-
Seismic response and performance prediction of steel buckling-restrained braced frames using machine-learning methods
PublikacjaNowadays, Buckling-Restrained Brace Frames (BRBFs) have been used as lateral force-resisting systems for low-, to mid-rise buildings. Residual Interstory Drift (RID) of BRBFs plays a key role in deciding to retrofit buildings after seismic excitation; however, existing formulas have limitations and cannot effectively help civil engineers, e.g., FEMA P-58, which is a conservative estimation method. Therefore, there is a need to...
-
Configuration of the reference stations as the element of national reference frame reliability
Publikacja -
Influence of soil–structure interaction on seismic pounding between steel frame buildings considering the effect of infill panels
PublikacjaThe present research aims to study the influence of the soil-structure interaction (SSI) and existence or absence of masonry infill panels in steel frame structures on the earthquake-induced pounding-involved response of adjacent buildings. The study was further extended to compare the pounding-involved behavior versus the independent behavior of structures without collisions, focusing much on dynamic behavior of single frames....
-
Relationship between saw blade teeth wear and kinematics of frame sawingmachines
PublikacjaPrzedstawiono rezultaty badań zużycia ostrzy pił trakowych i wpływ kinematyki pilarki ramowej na rozkład zużycia poszczególnych ostrzy pił.
-
Elastic wave propagation in frame structure in the context of structural health monitoring
PublikacjaPraca dotyczy propagacji fal sprężystych r konstrukcji ramowej w ośrodku typu belka Timoszenki. Do obliczeń numerycznych wykorzystano wielowęzłowe spektralne elementy skończone klasy C0. Omówiono algorytm całkowania po czasie i sformułowano wnioski dotyczące liczby węzłów na długość fali.
-
Stability and initial post-buckling behaviour of frame system with vertical bracings
PublikacjaStalowe hale są budowane jako układ ram płaskich połączonych stężeniami dachowymi i stężeniami pionowymi w postaci krzyżujących się prętów. W pracy przedstawiono analizę stateczności i zachowania pokrytycznego takiego układu poddanego działaniu obciążeń pionowych. Korzystając z warunków stacjonarności całkowitej energii potencjalnej wykazano, że punkt bifurkacji utraty stateczności jest niesymetryczny i niestateczny. Oznacza to,...
-
The effect of full-cell impregnation of pine wood (Pinus Sylvestris L.) on the fine dust content during sawing on a frame sawing machine
PublikacjaIn this paper the results of the analysis of the effect of the impregnation treatment of pine wood on the granularity of sawdust from the sawing process on the frame sawing machine PRW 15M are presented. Granulometric analyses of chips from impregnated and unimpregnated pine wood implies that the impregnation of pine wood does not affect the size and structure of the sawdust produced. A major ≈ 95% share of the formed chips is...
-
Packet routing and frame length optimization in wireless mesh networks with multicast communications
Publikacja -
Effects of Column Base Flexibility on Seismic Response of Steel Moment-Frame Buildings
PublikacjaSteel Moment Resisting Frames (SMRFs) are very popular lateral load resisting systems in many seismically active regions. However, their seismic response is strongly dependent on the rotational fixity of column base connections. Despite many studies (both experimental and numerical) in this particular area, available approaches for estimating column base flexibility have been validated only against laboratory test data. In the...
-
Influence of frame sawing machine´s kinematics on saw blade tooth wear.
PublikacjaW pracy przedstawiono wpływ kinematyki pilarki ramowej na zużycie ostrzy piłtrakowych.
-
1 kapitola: Status report on frame sawing machines for narrow-kerf sawing
PublikacjaW opracowaniu przedstawiono genezę pilarek ramowych oraz przecinania drewna cienkimi piłami. Omówiono ekonomiczne i ekologiczne zalety tego typu obróbki. Zaprezentowano kinematykę współczesnych pilarek dostępnych na rynkach światowych: Orbit, Mamuth oraz DSG Sonic. Szczegółowo opisano układ napędowy pilarek DTPX-30 i PRW15 z hybrydowym napędem głównym i całkowitym wyrównoważeniem dynamicznym układu.
-
Modelling of wave propagation in spatial frame elements - numerical simulations and experimental works
PublikacjaW pracy porównano rozwiązania propagacji fal sprężystych w ośrodku typu belka Timoszenki, uzyskane na drodze eksperymentalnej i numerycznej. Do obliczeń numerycznych wykorzystano wielowęzłowe spektralne elementy skończone klasy C0.Omówiono algorytm całkowania po czasie i sformułowano wnioski dotyczące liczby węzłów na długość fali.
-
Feed forces during cutting of wood on frame sawing machines with narrow-kerf saws.
PublikacjaW pracy przedstawiono wybrane efekty energetyczne procesu przecinania drewna na pilarce ramowej za pomocą cienkich pił. Opisano wyniki badań eksperymentalnych sił posuwu przy zastosowaniu pił o dobrej jakości krawędzi skrawających (piły ostre) oraz pił których krawędzie skrawające były obarczone błędami wykonania w postaci wyszczerbień i wykruszeń krawędzi skrawających. Badania przeprowadzono na pilarce ramowej PRW15M.
-
Cutting forces related to the direction of primary motion during machining on frame sawing machines.
PublikacjaW pracy przedstawiono efekty energetyczne przecinania drewna na pilarce ramowej za pomocą cienkich pił. Podano podstawy teoretyczne oraz wyniki badań doświadczalnych sił skrawania działających na kierunku ruchu głównego ( siły skrawania określano podczas podawania przecinanego materiału oraz w czasie gdy prędkość posuwu wynosiła 0).
-
Washboarding during cutting on frame sawing machines II. Experimental study of the saw blade behaviour
PublikacjaPraca jest swego rodzaju suplementem do referatu przedstawianego na 15th Inernational Wood Machining Seminar w Los Angeles, CA, USA. Opisano uzyskane wyniki badań doświadczalnych prowadzonych w oparciu o plan badań Hartley`a.Czynnikami badanymi były: naprężenia napinające brzeszczotu piły, częstotliwość skoków ramy piłowej oraz wysokość cięcia przedmiotu obrabianego. Czynnikami wynikowymi były: wysokość sfalowania powierzchni oraz...
-
Cutting model parameters from frame sawing of natural and impregnated Scots pine (Pinus sylvestris L.)
PublikacjaIn this paper, absolute and density normalized cutting model parameters of natural and impregnated Scots pine (Pinus sylvestris L.) are shown and a method for the calculation of their corresponding material properties in the principal material directions of wood is presented. The parameters were determined from measurements of cutting power on a sash gang saw, and are in detail the fracture toughness and the shear yield strength...
-
Rotationally inelastic collisions of electrons with H2 and N2 molecules: converged space-frame calculations at low energies.
PublikacjaW pracy zostały obliczone przekroje czynne na rotacyjne wzbudzenia cząsteczek H2 i N2 w wyniku zderzeń z niskoenergetycznymi elektronami. Układ silnie sprzężonych równań został rozwiązany w laboratoryjnym układzie odniesienia przy pomocy algorytmu MVPA.
-
Sawdust size distribution analysis of thermally modified and unmodified oak wood sawed on the frame sawing machine PRW15-M
PublikacjaW pracy przedstawiono wyniki analizy granulometrycznej składu wiórów drewna dębowego niemodyfikowanego i modyfikowanego termicznie uzyskanych podczas piłowania na pilarce ramowej PRW15-M z prędkością posuwu 1.67 mmin-1. Otrzymane trociny termicznie modyfikowanego drewna dębowego składają się z wiórów o ziarnistości w przedziale od 44.7 mm do 4.6 mm, podczas gdy dla drewna niemodyfikowanego zaobserwowano zmiany ziarnistości w granicach...