Filtry
wszystkich: 377
wybranych: 193
Wyniki wyszukiwania dla: START-UP
-
Evaluati on of long-term start up costs impact on short-term price based operational optimization of a CCGT using MILP
PublikacjaAn increasing share of the weather-dependent RES generation in the power system leads to the growing importance of flexibility of conventional power plants. They were usually designed for base load operation and it is a challenge to determine the actual long-term cycling costs, which account for an increase in maintenance and overhaul expenditures, increased forced outage rates and shortened life expectancy of the plant and components....
-
Acclimation of denitrifying activated sludge to a single vs. complex external carbon source during a start-up of sequencing batch reactors treating ammonium-rich anaerobic sludge digester liquors
PublikacjaIn this study, denitrification of ammonium- reach anaerobic sludge digester liquor was investigated during start-up periods of two laboratory- scale ‘‘fill-and-draw’’ reactors. One reactor was fed with a single carbon source (ethanol), whereas the other reactor was fed with a complex carbon source (fusel oil). During two acclimation experiments, the structure of microbial community involved in denitrification was analyzed using...
-
PROBLEMS OF THE STARTING AND OPERATING OF HYDRAULIC COMPONENTS AND SYSTEMS IN LOW AMBIENT TEMPERATURE (PART V) METHODS ENSURING CORRECT START-UP OF HYDRAULIC COMPONENTS OF SHIP’S ONBOARD DEVICES IN LOW AMBIENT TEMPERATURES
PublikacjaA large number of hydraulic devices and systems are started in low ambient temperatures. A good example of such a device is the hoisting winch on the ship. Starting hydraulic drive units in thermal shock conditions (rapid supply of hot oil to the cold unit) may lead to incorrect operation of the actuating system, for instance, due to the loss of clearance between cooperating elements. The article presents methods to prevent the...
-
Problems of the starting and operating of hydraulic components and systems in low ambient temperature. Part III.Methods of determining parameters for correct start-ups of hydraulic components and systems in low ambient temperatures
PublikacjaW artykule przedstawiono metody: eksperymentalną, analityczną i symulacji komputerowej określania zdatności oziębionych zespołów hydraulicznych do pracy w warunkach zasilania gorącym czynnikiem roboczym powodujących tzw. szok termiczny.
-
Exhaust Emission from Passenger Cars During Engine Cold Start and Warm-Up
Publikacja -
Euro III / Euro IV Emissions - A Study of Cold Start and Warm Up Phases with a SI (Spark Ignition) Engine
Publikacja -
Influence of type of material on performance of hydraulic components in thermal shock conditions
PublikacjaDuring the start-up of a hydraulic system in low ambient temperatures an incorrect operation may occur. The principles and conditions of safely operating hydraulic driven machines and devices are essential to designers and operators. For this reason the author of this article has conducted a series of tests on hydraulic components and systems in thermal shock conditions (cooled-down components were supplied with hot working medium)....
-
DESIGN THINKING ORIENTED METHODOLOGY IN GROUP PROJECT AS A STEP IN THE CDIO APPROACH
PublikacjaRecently much scientific research and industrial work is conducted in multidisciplinary teams, where cooperation between specialists from different areas of expertise is required in order to successfully address the challenging goals. Moreover, in start-up small companies the lack of supporting departments calls for additional multidisciplinary, economic and networking skills known as T-shaped personality. Recognizing these shortcomings...
-
Optimisation of turbine shaft heating process under steam turbine run-up conditions
PublikacjaAn important operational task for thermal turbines during run-up and run-down is to keep the stresses in the structural elements at a right level. This applies not only to their instantaneous values, but also to the impact of them on the engine lifetime. The turbine shaft is a particularly important element. The distribution of stresses depends on geometric characteristics of the shaft and its specific locations. This means a groove manufactured...
-
Research on the phenomena of warming up and free cooling down the car engine
PublikacjaThe average cold start temperature in Europe is 9 degrees C. However, not the average is the most important for the composition of exhaust gases and associated air pollution. The most onerous for the environment are the winter starts when automotive emissions of harmful gases add up in cities with those of home heating systems. The paper presents preliminary studies of warming up and cooling down processes in various environmental conditions....
-
A model development and experimental verification for a vapour microturbine with a permanent magnet synchronous generator
PublikacjaVapour microturbines with permanent magnet synchronous generators are implemented in micropower plants for dispersed power generation systems. The dynamic model of such a microturbine set was developed and presented. The developed relations result from the generic equations. Experimental data for two different working medium were used for model verification. A microturbine set model was tested during the changes in the parameters...
-
Analysis of diagnostic informativeness of the exhaust temperature of a naval gas turbine
PublikacjaThe conducted investigations aimed to carry out an analysis of the possibility that the failures identification in the automatic control system of a gas turbine engine could be worked out on the basis of measurements of the exhaust stream temperature behind the gas generator. The exhaust temperature represents a basic control parameter, enabling technical state evaluation of the engine within the operation process, which is observed...
-
Long-term operation of Kickuth-type constructed wetland applied to municipal wastewater treatment in temperate climate
PublikacjaThe purpose of this paper is to discuss the problem of changes of effectiveness of Kickuth-type constructed wetland with subsurface flow applied to domestic wastewater treatment. This study is based on an example of a wetland 3000 m2 in surface, serving 800 inhabitants, located in Poland. The results of chemical analysis showed that after an initial year of ‘start-up time’, the efficiency of pollutant removal gradually increased...
-
OPERATION OF TWO-SHAFT GAS TURBINE IN THE RANGE OF OPEN ANTI-SURGE VALVE
PublikacjaThis paper presents experimental tests of full-scale two-shaft gas turbine in the range of open anti-surge valve (ASV). The tests were carried out in a laboratory gas- turbine test stand belonging to Department of Automation and Power Engineering , Faculty of Ocean Engineering and Ship Technology , Gdańsk University of Technology. The tests covered the start-up and low load operation of the turbine set in the range of open...
-
A new method of wind farm active power curve estimation based on statistical approach
PublikacjaThe purpose of this paper is to solve the wind farm active power estimation problem, introducing the method which is based on a statistical approach and robust fitting. The proposed algorithm uses a statistical approach and compared to existing ones- includes a wind direction as well as the influence of turbine start-up procedure on the estimation. The results show that additional estimation inputs i.e. the wind direction and the...
-
Recent Advances in Loop Heat Pipes with Flat Evaporator
PublikacjaThe focus of this review is to present the current advances in Loop Heat Pipes (LHP) with flat evaporators, which address the current challenges to the wide implementation of the technology. A recent advance in LHP is the design of flat-shaped evaporators, which is better suited to the geometry of discretely mounted electronics components (microprocessors) and therefore negate the need for an additional transfer surface (saddle)...
-
Analysis of start energy of Stirling engine type alpha
PublikacjaThe Stirling engine type alpha is composed of two cylinders (expansion space E and compression space C), regenerator that forms the space between the cylinders and the buffer space (under the pistons). Before the start-up and as a result of long-term operation, the average pressure in the working space (above the pistons) and in the buffer space is the same. However, in the initial phase of operation, the average pressure in the...
-
Recovery of Anammox Biomass at Short Hydraulic Retention Time in a MBR Reactor
PublikacjaThe anammox system has been consider as an economical option for treating high concentration of nitrogen and poor in biodegradable orgaednic carbon wastewaters. This process is attractive option compared with conventional nitrogen removal because it provides a significant saving in aeration and organic addition for denitrification. The anammox technology has been applied mostly for concentrated nitrogenous wastewater containing...
-
Five-phase squirrel-cage motor. Construction and drive properties
PublikacjaThis paper presents the simulation and experimental results of a five-phase squirrel-cage induction motor. The new machine has been designed to operate in a drive system with third harmonic rotor flux injection in order to improve the motor torque utilization. The motor structure, the mathematical model as well as the laboratory prototype have been described. The motor speed-torque characteristics and transients are elaborated...
-
Entrepreneurial education and attitudes among young generations in a gender perspective: the case of Polish educational system
PublikacjaThis paper is an attempt to analyze the impact of entrepreneurship education on entrepreneurial attitudes and intentions of young people: male and female students of Polish high schools and universities. The author makes an effort to verify the impact of the exposure to the business education and entrepreneurs on the decision to start-up. Special emphasis will be placed on the gender differences when discussing a respective factors’...