Wyszukiwarka
Wyniki wyszukiwania dla: SHELL-MULTI-TUBE UNIT
-
Experimental investigation of thermal energy storage in shell-and-multi-tube unit with nano-enhanced phase change material
PublikacjaThis paper deals with thermal energy storage with use of nanoparticle enhanced phase change material in shell-and-multitube unit. The experiments are conducted under atmospheric pressure. Paraffin wax and two different fatty acids are used as base phase change material. Graphite and multi-walled carbon nanotubes serve as nanoparticles. Graphite nanoparticles are tested at the concentrations of 0.1%, 1% and 5% by weight, while multi-walled...
-
Experimental and theoretical study of a vertical tube in shell storage unit with biodegradable PCM for low temperature thermal energy storage applications
PublikacjaThis article presents the experimental investigations of the coconut oil-based TES module for HVAC applications in the ambient and-sub ambient temperature range. To properly study this problem modular experimental module and test loop were developed. Special attention has been paid to study the physical mechanism of the melting/solidification process for natural substance (coconut oil) which has perspectives to be used in thermal...
-
Effect of Tube Bundle Arrangement on the Performance of PCM Heat Storage Units
PublikacjaThe results of comprehensive study on charging and discharging of latent heat storage systems (LHSS) are presented. The multi tube shell-and-tube unit with a variable layouts of the tube bundles are examined. Two tube arrangements – in-line and staggered are tested. A variable number of tubes and different tube positions in a bundle are investigated. Moreover, two pitch ratios are studied. Three commercially available substances...
-
A new construction of shell-and-tube heat exchanger with impinging jets and minichannels technologies for heat recovery from gases – experimental analysis
PublikacjaA dynamic development of technologies allowing waste heat utilization is observed in a correspondence with a pro-ecological approach of the zero waste idea. Such approach becomes the most demanding in the area of low-temperature was heat sources, especially gaseous media. Till now, they were usually not utilized due to unfavorable thermal conditions and high costs. Therefore, the zero waste approach directs research on techniques...
-
Thermal Energy Storage with PCMs in Shell-and-Tube Units: A Review
PublikacjaThe paper presents a survey of the experimental and numerical studies of shell-and-tube systems in which phase change material (PCM) is used. Due to the multitude of design solutions for shell-and-tube systems, the emphasis is placed on double-tube (DT), triplex-tube (TT), and multitube (MT) units. Additionally, only single-pass systems are considered. Particular attention is paid to the method of heat transfer intensification....
-
Effect of tube bundle arrangement on performance of shell-and-tube latent heat storage system
PublikacjaThis work presents the results of experimental investigation on charging and discharging of latent heat storage systems (LHSS) in the form of shell-and-tube heat exchangers with a variable arrays of the tube bundles. The tests included two tube arrangements – in-line and triangular (staggered), a variable number of tubes in a bundle, two pitch ratios, and different tube positions in a bundle. Three commercial products (LTP56, RT54HC,...
-
Performance of the domestic micro ORC equipped with the shell-and-tube condenser with minichannels
PublikacjaIn this paper, the original compact shell-and-tube heat exchanger with circular minichannels of in-house design and manufacturing is presented as the condenser for the domestic micro heat and power plant investigations as well as other future technical applications. The heat exchanger is equipped with turbulizing baffles inside the shell. The shell itself is made of a tubular sleeve having an inner diameter of 0.067 m and the length...
-
Experimental Investigations on the Influence of Coil Arrangement on Melting/Solidification Processes
PublikacjaThe latent heat thermal energy storage units are very popular because of their high energy density and almost close to constant temperature during the charging/discharging. In the present study has been proposed new shell-and-coil geometry with a shifted coil position to enhance the performance of phase change thermal magazine. The experimental investigations have been performed both for the melting and solidification process of...
-
Thermal-Hydraulic Studies on the Shell-and-Tube Heat Exchanger with Minijets
PublikacjaIn this paper a patented design of a heat exchanger with minijets, with a cylindrical construction is presented. It is followed by the results of its systematic experimental investigations in the single-phase convection heat transfer mode. Based on these results, validation of selected correlations (coming from the literature) describing the Nusselt number was carried out. An assessment of the heat exchange intensification level...
-
Study on effective front region thickness of PCM in thermal energy storage using a novel semi-theoretical model
PublikacjaThermal energy storage in mobile applications, particularly battery of electric vehicles, is currently gaining a lot of importance. In this paper, a semi-theoretical time-dependent mathematical model of the phase change in a double shell thermal energy storage module has been developed where the inner tube is a heat exchange surface. An effective front region thickness for the melting and solidification process has been studied....
-
HEAT TRANSFER CHARACTERISTICS OF ENHANCED SHELL AND COIL HEAT EXCHANGER
PublikacjaIn the paper authors presented their own constructions of shell and tube heat exchangers with intensified heat transfer. The shell and coils heat exchangers are in common use in heat ventilations and air conditioning systems. Those types of recuperators are quite simple constructions, the low value of pressure drops and good conditions of heat transfer. The present study shows an experimental investigation of the heat transfer...
-
A simple approach to heat exchanger sizing optimisation by means of entrophy generation minimisation
PublikacjaIn the paper an attempt is presented to find the method of optimization of microtube diameter with respect to optimal thermal-hydraulic conditions in the single-phase shell-and-tube heat exchangers. The approach is based on consideration of pumping power at the condition of maximum heat transfer by the heat exchanger tube system. In the optimization method the tube diameter is first specified and then appropriate calculations are...
-
Performance analyses of helical coil heat exchangers. The effect of external coil surface modification on heat exchanger effectiveness
PublikacjaThe shell and coil heat exchangers are commonly used in heating, ventilation, nuclear industry, process plant, heat recovery and air conditioning systems. This type of recuperators benefits from simple construction, the low value of pressure drops and high heat transfer. In helical coil,centrifugal force is acting on the moving fluid due to the curvature of thetube results in the development. It has been long recognized that the...
-
A New Approach of Solidification Analysis in Modular Latent Thermal Energy Storage Unit Based on Image Processing
PublikacjaThe solidification process of RT18HC in a cylindrical shell and tube storage unit has been studied using a new methodology based on image processing. The main idea of the algorithm is to label the region of solidification and use statistical functions to calculate the dimensions of the solidification front over time. Said analysis includes two methods. The first method is to measure the solid fraction changes during solidification....
-
Experimental investigations on heat transfer enhancement in shell coil heat exchanger with VARIABLE Baffles GEOMETRY
PublikacjaThe paper presents the possibility of using passive intensification of heat transfer in the form of baffles to increase the energy efficiency of the shell and coil heat exchanger. The experiment was carried out by using a modular coil heat exchanger in the form of an electric heater. Water was used as a working fluid with constant thermal-flow parameters at the inlet of the module. It should be noted that experiments were made...
-
Thermal and economic investigation of straight and U-bend double tube heat exchanger with coiled wire turbulator
PublikacjaExperimental research has been carried out for four individual heat exchanger constructions, i.e., plain double tube, turbulized double tube, plain U-bend and U-bend with turbulator. Tests were made for the water-water system. The study covered a wide measuring range, i.e., Re = 800–9000 – on the shell side, for a constant cold water temperature of 9 ◦C and hot water of 50 ◦C. The heat exchangers were made from copper tubes with...
-
Heat transfer enhancement of modular thermal energy storage unit for reversible heat pump cooperation
PublikacjaThe following article presents experimental comparison research on a hexagonal shelland-tube latent thermal energy storage (TES). Such shape of a shell was deliberately chosen instead of a cylindrical one due to its high modularity and with intent for future applications in automobiles (EV and PHEV) air conditioning systems (HVAC). Two geometries of helical coils, acting as tubes, were studied in this article. One was a simple...
-
Experimental investigation of two-phase thermosyphon heat exchanger charged with acetone
PublikacjaThis paper presents thermal characteristics of prototype of a two-phase thermosyphon heat exchanger (TPTHEx) charged with acetone as a working fluid. The TPTHEx consists of two horizontal cylindrical vessels connected by two risers and a downcomer. Tube bundles placed in the lower and upper cylinders work as an evaporator and a condenser, respectively. The tested TPTHEx operates in a vacuum. Therefore, the working liquid is boiled...
-
Application of linear buckling sensitivity analysis to economic design of cylindrical steel silos composed of corrugated sheets and columns
PublikacjaThe paper deals with global stability of steel cylindrical silos composed of corrugated walls and vertical columns with loads imposed by a bulk solid following Eurocode 1. The optimum silo design with respect to the steel weight was based on a sensitivity analysis method. The changes of silo column profiles at each design step were performed by means of influence lines for the buckling load factor due to the unit column bending...
-
Property-performance relationship of core-shell structured black TiO2 photocatalyst for environmental remediation
PublikacjaUnderstanding the relationship between the properties and performance of black titanium dioxide with core-shell structure (CSBT) for environmental remediation is crucial for improving its prospects in practical applications. In this study, CSBT was synthesized using a glycerol-assisted sol-gel approach. The effect of different water-to-glycerol ratios (W:G = 1:0, 9:1, 2:1, and 1:1) on the semiconducting and physicochemical properties...
-
Numerical Modelling of Forced Convection of Nanofluids in Smooth, Round Tubes: A Review
PublikacjaA comprehensive review of published works dealing with numerical modelling of forced convection heat transfer and hydrodynamics of nanofluids is presented. Due to the extensive literature, the review is limited to straight, smooth, circular tubes, as this is the basic geometry in shell-and-tube exchangers. Works on numerical modelling of forced convection in tubes are presented chronologically in the first part of the article....
-
Wpływ smarowności na działania układu tribologicznego (impact of lubricity on the tribological system action)
Publikacjathe paper presents analysis and evaluation, based on tests results, of the impact of lubricity of the used lubricating oils (shell argina t 40) on the action of boundary layer of sulzer 6zl40/48 engines aboard the ''włocławek'' sea-going ship. for comparison purposes, the same oils were tested with the ceramizer four-stroke engine (all types of the vidar four-stroke engines) regeneration agent added. so understood boundary layer...
-
Multi-region fuzzy logic controller with local PID controllers for U-tube steam generator in nuclear power plant
PublikacjaIn the paper, analysis of multi-region fuzzy logic controller with local PID controllers for steam generator of pressurized water reactor (PWR) working in wide range of thermal power changes is presented. The U-tube steam generator has a nonlinear dynamics depending on thermal power transferred from coolant of the primary loop of the PWR plant. Control of water level in the steam generator conducted by a traditional PID controller...
-
Thermodynamic and geometrical characteristics of mixed convection heat transfer in the shell and coil tube heat exchanger with baffles
PublikacjaThe article presents passive heat transfer enhancement method in the form of baffles to increase the energy efficiency of the shell coil heat exchanger. Conducted literature review shows that, despite numer- ous studies, there is little work on the intensification of heat transfer at the shell side. Most of the work focuses on the impact of geometrical parameters of the coil itself. This article successfully proves that it is possible...
-
Experimental and numerical investigation on shell and coil storage unit with biodegradable PCM for modular thermal battery applications
PublikacjaThermal energy storage (TES) in automotive applications is currently growing in importance. TES can visibly reduce primary energy consumptions, decrease CO2 emission, and improve thermal comfort in electric as well as hybrid vehicles. However, to meet the new ambitious target (15% reduction of CO2 emissions in the new cars until 2025) it is required to use plug-in electric vehicles. For this reason, this paper focuses on the optimization...
-
Multi-objective optimization of the cavitation generation unit structure of an advanced rotational hydrodynamic cavitation reactor
PublikacjaHydrodynamic cavitation (HC) has been widely considered a promising technique for industrial-scale process intensifications. The effectiveness of HC is determined by the performance of hydrodynamic cavitation reactors (HCRs). The advanced rotational HCRs (ARHCRs) proposed recently have shown superior performance in various applications, while the research on the structural optimization is still absent. The present study, for the...
-
Multi-functional monodispersed SiO2-TiO2 core-shell nanostructure and TEOS in the consolidation of archaeological lime mortars surfaces
PublikacjaArchaeological traditional lime mortars are susceptible to many environmental conditions such as the impact of water (rain, humidity, groundwater, etc.), variation of temperatures' degrees, wind and/or pollution. Accordingly, this research aims to provide newly assessed multifunctional Nano-coating for the purpose of archaeological lime mortar protection. For this, the study combined physicochemical and mechanical characterizations...
-
Concomitant use of veno-arterial extracorporeal membrane oxygenation and Impella in the intensive care unit: a case report of fulminant myocarditis with multi-organ failure
Publikacja -
Bi-GRU-APSO: Bi-Directional Gated Recurrent Unit with Adaptive Particle Swarm Optimization Algorithm for Sales Forecasting in Multi-Channel Retail
PublikacjaIn the present scenario, retail sales forecasting has a great significance in E-commerce companies. The precise retail sales forecasting enhances the business decision making, storage management, and product sales. Inaccurate retail sales forecasting can decrease customer satisfaction, inventory shortages, product backlog, and unsatisfied customer demands. In order to obtain a better retail sales forecasting, deep learning models...
-
Tomasz Janowski dr
OsobyTomasz Janowski jest kierownikiem Katedry Informatyki w Zarządzaniu, Politechnika Gdańska; profesorem wizytującym w Department for E-Governance and Administration, University for Continuing Education Krems, Austria; oraz współredaktorem naczelnym czasopisma Government Information Quarterly, Elsevier. Wcześniej był założycielem i kierownikiem United Nations University Operating Unit on Policy-Driven Electronic Governance (UNU-EGOV),...
-
A higher order shell element for wave propagation in isotropic shell structures
PublikacjaThe presents the new multi mode higher order shell element for wave propagation problems in shell structures.
-
Junctions In Shell Structures: A Review
PublikacjaMany shell structures used in modern technology consist of regular shell parts joined together along their common boundaries. We review different theoretical, numerical, and experimental approaches to modelling, analyses and design of the compound shell structures with junctions. Several alternative forms of boundary, continuity and jump conditions at the singular midsurface curves modelling the shell junction are reviewed. We...
-
Wiktoria Wojnicz dr hab. inż.
OsobyDSc in Mechanics (in the field of Biomechanics) - Lodz Univeristy of Technology, 2019 PhD in Mechanics (in the field of Biomechanics) - Lodz Univeristy of Technology, 2009 (with distinction) Publikacje z listy MNiSW (2009 - ) Wojnicz W., Wittbrodt E., Analysis of muscles' behaviour. Part I. The computational model of muscle. Acta of Bioengineering and Biomechanics, Vol. 11, No.4, 2009, p. 15-21 Wojnicz W., Wittbrodt E.,...
-
Implementation of high-speed data transmission technological demonstrator using software defined radio technology
PublikacjaIn the article implementation of a high-speed data transmission technological demonstrator using software defined radio technology is presented. A system architecture design including asymmetric framing transmission organization, which differs from the ones used in cellular systems is described. The construction of technological demonstrator consisting of a management unit, radio unit and programmable multi-threaded software performing...
-
Jan Wajs dr hab. inż.
Osoby -
The impact of footing conditions of a vertical-axis floating-roof tank on structural shell deformation
PublikacjaStructural shells of fuel tanks are often subjected to geometric imperfections which may lead to exceeding the ultimate and serviceability limit states. One of the means triggering shell deformation is non-uniform settlement caused by incoherent soil conditions. Analysis carried out in the work concerns of vertical-axis, floating-roof cylindrical shell which volume is 50.000 m3, founded on a complex multi-layered soil. The sensitivity...
-
Drilling couples and refined constitutive equations in the resultant geometrically non-linear theory of elastic shells
PublikacjaIt is well known that distribution of displacements through the shell thickness is non-linear, in general. We introduce a modified polar decomposition of shell deformation gradient and a vector of deviation from the linear displacement distribution. When strains are assumed to be small, this allows one to propose an explicit definition of the drilling couples which is proportional to tangential components of the deviation vector....
-
Elastoplastic nonlinear FEM analysis of FGM shells of Cosserat type
PublikacjaThe paper is a continuation of [1] where the formulation of the elastic constitutive law for functionally graded materials (FGM) on the grounds of nonlinear 6-parameter shell theory with the 6th parameter (the drilling degree of freedom) was presented. Here the formulation is extended to the elasto-plastic range. The material law is based on Cosserat plasticity and employs the well-known Tamura-Tomota-Ozawa (TTO) [2] mixture...
-
Data-Driven Surrogate-Assisted Optimization of Metamaterial-Based Filtenna Using Deep Learning
PublikacjaIn this work, a computationally efficient method based on data driven surrogate models is pro-posed for the design optimization procedure of a Frequency Selective Surface (FSS)-based filtering antenna (Filtenna). A Filtenna acts as a as module that simultaneously pre-filters unwanted sig-nals, and enhances the desired signals at the operating frequency. However, due to a typically large number of design variables of FSS unit elements,...
-
The electronic structure of p-xylylene and its reactivity with vinyl molecules
PublikacjaThe electronic states of p-xylylene molecule were described at the multi-configurational CASSCF/MRMP2 level of theory. The closed-shell singlet state representing the quinoidal p-xylylene molecule was pre-dicted to be the ground electronic state whereas the triplet (benzoidal) and the singlet open-shell states were found to be much higher in energy (by 159 and 423 kJ/mol, respectively, as found at the CASSCF(8,8)/6-31+G(d) level)....
-
GPU based implementation of Temperature-Vegetation Dryness Index for AVHRR3 Satellite Data
PublikacjaPaper presents an implementation of TVDI (Temperature-Vegetation-Dryness Index) algorithm on GPU (Graphics Processing Unit). Calculation of this index is based on LST (Land Surface Temperature) and NDVI (Normalized Difference Vegetation Index). Discussed results are based on multi-spectral imagery retrieved from AVHRR3 sensors for area of Poland. All phases of TVDI implementation on GPU are modified in respect to CUDA platform....
-
Finite element matrix generation on a GPU
PublikacjaThis paper presents an efficient technique for fast generation of sparse systems of linear equations arising in computational electromagnetics in a finite element method using higher order elements. The proposed approach employs a graphics processing unit (GPU) for both numerical integration and matrix assembly. The performance results obtained on a test platform consisting of a Fermi GPU (1x Tesla C2075) and a CPU (2x twelve-core...
-
Implementation of TVDI calculation for coastal zone
PublikacjaPaper will show an implementation of TVDI (Temperature-Vegetation-Dryness Index) algorithm on GPU (Graphics Processing Unit). Calculation of this index is based on LST (Land Surface Temperature) and NDVI (Normalized Difference Vegetation Index). Discussed results are based on multi-spectral imagery retrieved from AVHRR3 sensors for area of Poland, especially from region of Gdańsk coastal zone. All phases of TVDI implementation...
-
Surface sliding in human abdominal wall numerical models: Comparison of single-surface and multi-surface composites
PublikacjaDetermining mechanical properties of abdominal soft tissues requires a coupled experimental-numerical study, but first an appropriate numerical model needs to be built. Precise modeling of human abdominal wall mechanics is difficult because of its complicated multi-layer composition and large variation between specimens. There are several approaches concerning simplification of numerical models, but it is unclear how far one could...
-
RF Multi-Functional Input-Reflectionless Dispersive-Delay Structure With Sharp-Rejection Filtering Using Channelization Techniques
PublikacjaA class of RF multi-functional input-reflectionless dispersive-delay structure (DDS) with linear-type in-band groupdelay variation and sharp-rejection bandpass-filtering capability is reported. It exploits a two-branch-channelized/balanced-type circuit with similar low-order reflective DDS units inside its channels, which are connected through input/output 3-dB quadrature wideband couplers. The adopted DDS unit is based on a coupledresonator...
-
Exploiting multi-interface networks: Connectivity and Cheapest Paths
PublikacjaLet G = (V,E) be a graph which models a set of wireless devices (nodes V) that can communicate by means of multiple radio interfaces, according to proximity and common interfaces (edges E). The problem of switching on (activating) the minimum cost set of interfaces at the nodes in order to guarantee the coverage of G was recently studied. A connection is covered (activated) when the endpoints of the corresponding edge share at...
-
Design and Implementation of Multi-Band Reflectarray Metasurface for 5G Millimeter Wave Coverage Enhancement
PublikacjaA compact low-profile multi-band millimeter-wave (mm-wave) reflectarray metasurface design is presented for coverage enhancement in 5G and beyond cellular communication. The proposed single-layer metasurface exhibits a stable reflection response under oblique incidence angles of up to 60o at 24 and 38 GHz, and transmission response at 30 GHz, effectively covering the desired 5G mm-wave frequency bands. The proposed reflectarray...
-
Light‐Driven Multi‐Charge Separation in a Push‐Pull Ruthenium‐Based Photosensitizer – Assessed by RASSCF and TDDFT Simulations
PublikacjaThe performance of photosensitizers in the field of, for example, solar energy conversion, relies on their light-harvesting efficiency in the visible region, population of long-lived charge separated intermediates, as well as their charge-accumulation capacity amongst other properties. In this computational study, we investigate the photophysical properties of a bis(bipyridyl)ruthenium(II)-based black dye (Ru) incorporating a chromophoric...
-
Load effect impact on the exploitation of concrete machine foundations used in the gas and oil industry
PublikacjaMachine foundations is a critical topic in the gas and oil industry, which design and exploitation require extensive technical knowledge. Machine foundations are the constructions which are intended for mounting on it a specific type of machine. The foundation has to transfer dynamic and static load from machine to the ground. The primary difference between machine foundations and building foundations is that the machine foundations...
-
Measurement of luminance and color uniformity of displays using the large-format scanner
PublikacjaUniformity of display luminance and color is important for comfort and good perception of the information presented on the display. Although display technology has developed and improved a lot over the past years, different types of displays still present a challenge in selected applications, e.g. in medical use or in case of multi-screen installations. A simplified 9-point method of determining uniformity does not always produce...