Wyszukiwarka
Filtry
wszystkich: 1948
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: air
-
INCREASING THE COUNTRY'S SECURITY AND PUBLIC TRANSPORT ACCESSIBILITY BY CREATING A NETWORK OF SMALL AIRPORTS
PublikacjaIt has been shown that by creating a network of small airports, it is possible to increase the communication accessibility of large population groups and the country's security, including safety at sea. The airports mentioned above may also be located on land considered to be weak from an engineering point of view. These include, for example, wetlands, swamps, flood embankments, poor coastal belt grounds, and reclaimed land. A...
-
Lead Airgun Projectiles Inside the Maxillary Sinuses—Therapeutic Approaches through the Years: A Systematic Review of Case Reports
Publikacja -
Comparison of ETView SL, Airtraq, and Macintosh laryngoscopes for face-to-face tracheal intubation: a randomized crossover manikin trial
Publikacja -
A Dual-Polarized 39 GHz 4x4 Microstrip Antenna Array for 5G MU-MIMO Airflight Cabin Connectivity
PublikacjaThis paper presents the design, fabrication, and experimental validation of a 39 GHz dual-polarized 4x4 microstrip antenna array. The array consists of 16 slot coupled circular microstrip patches, fed through SMPS connectors. The procedure requiring a reduced number of cables for measurement of the uniformly excited antenna array is also presented. The array exhibits 18 dBi peak gain and 2.9 GHz reflection bandwidth and is intended...
-
Long term measurements of PM1, PM2.5, PM10 and NO2 in open-air at Gdansk (Poland) area using low-cost sensors together with the reference results
Dane BadawczeThe measurements results of open-air measurements made using the following low-cost sensors: particulate matter (PM) sensor SPS30 from Sensirion, NO2 electrochemical sensor SGX-7NO2 from SGX Sensortech, NO2 electrochemical sensor 7E4-NO2 from SemaTech, compact MOS air quality sensor MiCS 2714 from SGX Sensortech, BME280 (Bosch) environmental sensor...
-
Hydrodynamic studies in magnetically assisted external-loop airlift reactor
Publikacja -
Korzystne cechy bioreaktora airlift z odwrotną warstwą fluidalną
PublikacjaZbadano wpływ parametrów procesowych i właściwości fizykochemicznych na wynik i czas procesu biodegradacji ketonów w roztworach wodnych. Stosowano kultury bakterii A. Calcoaceticus. Stwierdzono wzrost czasu biodegradacji ze wzrostem początkowego stężenia ketonów oraz ze wzrostem pH w roztworach alkalicznych.
-
Studium wybranych właściwości radiowej sieci dostępowej AIRSPAN z dynamicznym przydziałem kanału (Wersja 1.0)
PublikacjaPrzeanalizowano właściwości radiowej sieci dostępowej Airspan z dynamicznym przydziałem. W oparciu o przeprowadzone badania instalacji pilotażowej dokonano oceny systemu w oparciu o wymagania Ministerstwa Łączności dotyczące radiowych systemów dostępowych.
-
Particle Image Velocimetry Measurements of Airflow in Electrohydrodynamic Device for Dust Particle Collection
PublikacjaIn this paper the pumping effect of air in the electrohydrodynamic (EHD) device for dust particle collection is presented. To induce an airflow in this EHD device corona discharge was used. The discharge was generated between the one-sided spike electrodes and the plate electrodes. The asymmetric electric field and generated discharge resulted in a unidirectional airflow through the EHD device. The current-voltage characteristics...
-
Potential Toxic Effects of Airport Runoff Water Samples on the Environment
PublikacjaDespite the positive aspects of the intensive development of aviation, airports are considered large-scale polluters. Pollution caused by runoff water (stormwater) is one of the major problems related to airport operations. The aim of this study was to characterize the potential toxic impact on aquatic life from runoff water discharges from four international airports in Europe. Samples of stormwater were collected at airports...
-
Substrate specificity and inhibitory study of human airway trypsin-like protease
Publikacja -
In Reference to Voice, Swallow and Airway Outcomes Following Tracheostomy for COVID-19
Publikacja -
Blind intubation through the supraglottic airway laryngopharyngeal tube with a biohazard suit
Publikacja -
Across-shift changes in upper airways after exposure to bacterial cell wall components
Publikacja -
Vertex (Buenos Aires, Argentina)
Czasopisma -
Occupational exposure to anaerobic bacteria in a waste sorting plant
Publikacja -
Validation of odor concentration from mechanical-biological treatment piles using static chamber and wind tunnel with different wind speed values
Publikacja -
A comparative study of the performance of passive samplers
PublikacjaPodstawowym celem podjętych badań było porównanie pracy dozymetrów pasywnych wykorzystywanych na etapie izolacji i wzbogacania lotnych związków organicznych z powietrza atmosferycznego na terenie aglomeracji Trójmiejskiej. Jako próbniki do pobierania próbek analitów zastosowano komercyjne dozymetry pasywne typu dyfuzyjnego (Radiello i Orsa 5) oraz dozymetry typu permeacyjnego własnej konstrukcji wyposażone w półprzepuszczalną membranę...
-
Preliminary Evaluation of Airlaid Nonwovens with Superabsorbent for Use in Protective Footwear: Tests Involving a Thermal Foot Model and Climatic Chamber
Publikacja -
Comparative Analysis of Numerical and Experimental Studies of the Airflow Around the Sample of Urban Development
PublikacjaIn this paper, on the background of a short overview of the recent advances in the field of Environmental Wind Engineering (EWE), a comparison of wind tunnel experiment and numerical simulation for some cases of airflow around an urban layout have been reported. The purpose of the study is quantitative and qualitative comparison of measurements in the wind tunnel as well as numerical simulation using Ansys Fluent software. The...
-
Particle Image Velocimetry Measurements of Airflow in Electrohydrodynamic Device for Dust Particle Collection
PublikacjaIn this paper the electrohydrodynamic (EHD)device for gas pumping and cleaning is presented. To induce an airflow in this EHD device corona discharge was used. The discharge was generated between the one-sided spike electrodes and the plate electrodes. An asymmetric electric field and generated discharge result in unidirectional gas flow through the EHD device. The current-voltage characteristics were measured and the corona discharge...
-
The Undisrupted Growth of the Airbnb Phenomenon between 2014–2020. The Touristification of European Cities before the COVID-19 Outbreak
PublikacjaAs a result of the Airbnb eruption, not only has the character of the short-term rental market been completely transformed, but the decades long growth in tourism has also been further accelerated. Therefore, due to the new demands of the tourism economy, the major shift in the usage of historic city centers occurred–the process of ‘touristification’, that results in the emergence of its new, unsustainable form. Despite the significance...
-
Advances in Aircraft and Spacecraft Science
Czasopisma -
AIRCRAFT ENGINEERING AND AEROSPACE TECHNOLOGY
Czasopisma -
Propagation of guided elastic waves in shell-type aircraft structural elements
PublikacjaW pracy przedstawiony powłokowy spektralny element skończony do analizy zjawiska propagacji fal sprężystych w elementach konstrukcyjnych typu powłokowego.
-
Liquid circulation in the agitated airlift reactor with the high gas disengagement zone
PublikacjaPrzedstawiono doświadczalne zależności stopnia zatrzymania gazu i prędkości cyrkulacji cieczy od prędkości przepływu gazu i częstości obrotów mieszadła. Obserwowano wzrost prędkości cyrkulacji cieczy ze wzrostem wysokości strefy napowietrzania. Dla niskich częstości obrotów mieszadła prędkość cyrkulacji cieczy wzrastała wraz ze wzrostem prędkości przepływu gazu, natomiast dla wysokich cząstości obrotów mieszadła prędkość cyrkulacji...
-
Dynamic analysis of the first stage compressor bladed disc of an aircraft engine
Publikacja -
Airfoil Design Under Uncertainty Using Non-Intrusive Polynomial Chaos Theory and Utility Functions
PublikacjaFast and accurate airfoil design under uncertainty using non-intrusive polynomial chaos (NIPC) expansions and utility functions is proposed. The NIPC expansions provide a means to efficiently and accurately compute statistical information for a given set of input variables with associated probability distribution. Utility functions provide a way to rigorously formulate the design problem. In this work, these two methods are integrated...
-
Fully Separated Flow Control Using DBD Plasma Actuators Located at the Leading Edge of an Airfoil
PublikacjaIn the framework of the PLASMAERO European project, experiments were conducted to investigate the authority of surface DBD plasma actuators to alter a fully separated flow around an airfoil in order to improve its aerodynamic performances in its natural stall regime. In this paper, unsteady excitation control is more specifically investigated. The key control parameter studied here is the burst frequency which periodically imposes...
-
Equivalent temperature for design of airport pavements using mechanistic-empirical methods
PublikacjaThe paper presents implementation of equivalent temperature for design of airport asphalt pavements. The calculation methods of equivalent temperature: the Shell method, the French method and method that use the Asphalt Institute fatique criteria were presented. An example of calculations of equivalent temperature for Gdansk Airport was introduced and discussed. It was shown that methods of calculation of equivalent temperature...
-
Automated detection of sleep apnea and hypopnea events based on robust airflow envelope tracking
PublikacjaThe paper presents a new approach to detection of apnea/hypopnea events, in the presence of artifacts and breathing irregularities, from a single-channel airflow record. The proposed algorithm identifies segments of signal affected by a high amplitude modulation corresponding to apnea/hypopnea events. It is shown that a robust airflow envelope—free of breathing artifacts—improves effectiveness of the diagnostic process and allows...
-
Automatic classification and mapping of the seabed using airborne LiDAR bathymetry
PublikacjaShallow coastal areas are among the most inhabited areas and are valuable for biodiversity, recreation and the economy. Due to climate change and sea level rise, sustainable management of coastal areas involves extensive exploration, monitoring, and protection. Current high-resolution remote sensing methods for monitoring these areas include bathymetric LiDAR. Therefore, this study presents a novel methodological approach to assess...
-
Trailing-Edge Separation Control of a NACA 0015 Airfoil Using Dielectric-Barrier-Discharge Plasma Actuators
PublikacjaThis paper presents a part of the works conducted in the Plasmaero European project (task 3.1), where the trailing-edge flow separation of a NACA 0015 airfoil has been controlled using four different dielectric barrier discharge (DBD) actuator types at three institutions across Europe. The results show that it is possible to enhance the aerodynamic performance of aircraft at speeds up to 40 m/s. Dielectric-barrier-discharge vortex...
-
Enhancement of lift and drag performances of a NACA0012 airfoil by multi-DBD plasma actuator with additional floating interelectrodes
PublikacjaIt is clear that the improvement of aircraft aerodynamic performances is currently and will continue to be a significant area of research for the aeronautical industry. The current study is focused on theenhancement of aerodynamic airfoil performances by using a multi-DBD plasma actuator mounted around the model leading-edge. Experiments have been conducted at the University of Orleans, in the 2 m x 2 m test section of a large...
-
Zastosowanie reaktora airlift z odwrotną warstwą fluidalną do biodegradacji dimetyloketonu.
PublikacjaProwadzono biodegradację modelowych ścieków zawierających dimetyloketon w obecności unieruchomionych bakterii Acinetobacter calcoaceticus. Eksperymenty przeprowadzono w reaktorze airlift z cyrkulacja zewnętrzną. Badano wpływ parametrów procesowych na czas biodegradacji dimetyloketonu.
-
Reconfigurable Dual Active Bridge (DAB) Converter Topology for Aircraft Application System
Publikacja -
An adaptive wing for a samll-aircraft application with a configuration of fibre Bragg greting sensors
PublikacjaW pracy przedstawiono koncepcję skrzydła o zmiennej geometrii wymuszanej układem siłowników zbudowanych z matriału z pamięcią kształtu oraz układem czujników optycznych z siatką Bragga do monitorowania jego stanu odkształceń.
-
Nonlinear model of a synchronous generator for analysis of more electric aircraft power systems
PublikacjaA nonlinear model for studying a variable-speed synchronous generator (SG) in more electric aircraft (MEA) power system has been developed. The saturation effects of the SG magnetic circuit have been considered. The model has been implemented in the Synopys/Saber simulation environment. The modelling language MAST has been used to elaborate the SG model. The model exhibit a network with the same number of external terminals/ports...
-
Multimodal Imaging Using Raman Spectroscopy and FTIR in a Single Analytical Instrument with a Microscope (Infrared Raman Microscopy AIRsight, Shimadzu): Opportunities and Applications
Publikacja -
Determination of flow properties of a serial connection of a pressure relief valve (C=6.2, b=0.38) and a silencer (C=1.4) from changes in air pressure in a tank being emptied
Dane BadawczeThe aim of the study was to determine the flow properties of serial connection of pneumatic components.The experiments were to measure the pressure changes in a being emptied tank for a pressure relief valve and a silencer arranged in-line. Three test configurations were used: (1) being emptied tank -> PRV -> ambient atmosphere, (2) pressure source...
-
Determination of flow properties of a serial connection of a pressure relief valve (C=3.3, b=0.40) and a silencer (C=3.0) from changes in air pressure in a tank being emptied
Dane BadawczeThe aim of the study was to determine the flow properties of serial connection of pneumatic components.The experiments were to measure the pressure changes in a being emptied tank for a pressure relief valve and a silencer arranged in-line. Three test configurations were used: (1) being emptied tank -> PRV -> ambient atmosphere, (2) pressure source...
-
Determination of flow properties of a serial connection of a pressure relief valve (C=6.4, b=0.45) and a silencer (C=7.0) from changes in air pressure in a tank being emptied
Dane BadawczeThe aim of the study was to determine the flow properties of serial connection of pneumatic components.The experiments were to measure the pressure changes in a being emptied tank for a pressure relief valve and a silencer arranged in-line. Three test configurations were used: (1) being emptied tank -> PRV -> ambient atmosphere, (2) pressure source...
-
Determination of flow properties of a serial connection of a directional control valve (C=2.0, b=0.11) and a silencer (C=3.4) from changes in air pressure in a tank being emptied
Dane BadawczeThe aim of the study was to determine the flow properties of serial connection of pneumatic components.The experiments were to measure the pressure changes in a being emptied tank for a directional control valve and a silencer arranged in-line. Three test configurations were used: (1) being emptied tank -> DCV -> ambient atmosphere, (2) pressure...
-
Determination of flow properties of a serial connection of a directional control valve (C=2.4, b=0.26) and a silencer (C=1.4) from changes in air pressure in a tank being emptied
Dane BadawczeThe aim of the study was to determine the flow properties of serial connection of pneumatic components.The experiments were to measure the pressure changes in a being emptied tank for a directional control valve and a silencer arranged in-line. Three test configurations were used: (1) being emptied tank -> DCV -> ambient atmosphere, (2) pressure...
-
Determination of flow properties of a serial connection of a pressure relief valve (C=4.4, b=0.42) and a silencer (C=1.4) from changes in air pressure in a tank being emptied
Dane BadawczeThe aim of the study was to determine the flow properties of serial connection of pneumatic components.The experiments were to measure the pressure changes in a being emptied tank for a pressure relief valve and a silencer arranged in-line. Three test configurations were used: (1) being emptied tank -> PRV -> ambient atmosphere, (2) pressure source...
-
Determination of flow properties of a serial connection of a pressure relief valve (C=5.3, b=0.38) and a silencer (C=3.4) from changes in air pressure in a tank being emptied
Dane BadawczeThe aim of the study was to determine the flow properties of serial connection of pneumatic components.The experiments were to measure the pressure changes in a being emptied tank for a pressure relief valve and a silencer arranged in-line. Three test configurations were used: (1) being emptied tank -> PRV -> ambient atmosphere, (2) pressure source...
-
Determination of flow properties of a serial connection of a pressure relief valve (C=7.3, b=0.49) and a silencer (C=6.8) from changes in air pressure in a tank being emptied
Dane BadawczeThe aim of the study was to determine the flow properties of serial connection of pneumatic components.The experiments were to measure the pressure changes in a being emptied tank for a pressure relief valve and a silencer arranged in-line. Three test configurations were used: (1) being emptied tank -> PRV -> ambient atmosphere, (2) pressure source...
-
Determination of flow properties of a serial connection of a directional control valve (C=2.4, b=0.26) and a silencer (C=7.0) from changes in air pressure in a tank being emptied
Dane BadawczeThe aim of the study was to determine the flow properties of serial connection of pneumatic components.The experiments were to measure the pressure changes in a being emptied tank for a directional control valve and a silencer arranged in-line. Three test configurations were used: (1) being emptied tank -> DCV -> ambient atmosphere, (2) pressure...
-
Determination of flow properties of a serial connection of a pressure relief valve (C=6.2, b=0.38) and a silencer (C=3.4) from changes in air pressure in a tank being emptied
Dane BadawczeThe aim of the study was to determine the flow properties of serial connection of pneumatic components.The experiments were to measure the pressure changes in a being emptied tank for a pressure relief valve and a silencer arranged in-line. Three test configurations were used: (1) being emptied tank -> PRV -> ambient atmosphere, (2) pressure source...
-
Determination of flow properties of a serial connection of a pressure relief valve (C=5.3, b=0.38) and a silencer (C=6.8) from changes in air pressure in a tank being emptied
Dane BadawczeThe aim of the study was to determine the flow properties of serial connection of pneumatic components.The experiments were to measure the pressure changes in a being emptied tank for a pressure relief valve and a silencer arranged in-line. Three test configurations were used: (1) being emptied tank -> PRV -> ambient atmosphere, (2) pressure source...