Wyniki wyszukiwania dla: energy and heating
-
The reduction of auxiliaries power demand: The challenge for electromobility in public transportation
PublikacjaAn important role in the consumption of electric energy in urban transport are non-traction needs (auxiliaries), the main part of which is heating and air condition (HVAC). Auxiliaries are responsible for almost half of total energy consumption (normal weather conditions) and in the winter (or hot summer) it reaches up to 70% in daily scale. The reduction of energy used for non-traction needs is currently the main challenge related...
-
Energy policy and the role of bioenergy in Poland
PublikacjaPrzedstawiono sytuacje energetyczną kraju. Omówiono poszczególne sektory wytwarzania energii oraz zapotrzebowania na energię i paliwa. Omówiono przekształcenia sektorów energetycznych w Polsce na przestrzeni lat 1990-2002. Na tym tle przedstawiono techniczne, ekonomiczne, społeczne i prawne aspekty rozwoju energetyki źródeł odnawialnych a w szczególności opartych o bioenergię. Przedstawiono wnioski dla Polski płynące z dotychczasowych...
-
Optimisation of turbine shaft heating process under steam turbine run-up conditions
PublikacjaAn important operational task for thermal turbines during run-up and run-down is to keep the stresses in the structural elements at a right level. This applies not only to their instantaneous values, but also to the impact of them on the engine lifetime. The turbine shaft is a particularly important element. The distribution of stresses depends on geometric characteristics of the shaft and its specific locations. This means a groove manufactured...
-
Thermally stimulated currents in amorphous solids due to complex heating regimes
PublikacjaPodano opis teoretyczny prądów termicznie stymulowanych w ciałach amorficznych. Dokonano rozszerzenia istniejących wzorów przybliżonych na przypadki opóźnionego i krokowego ogrzewania próbki. Otrzymane wyrażenia zweryfikowano za pomocą obliczeń numerycznych dla przypadku wykładniczego rozkładu pułapek.
-
Influence of material properties of charge on electrical parameters of induction heating setup
Publikacja -
Video component of a computer system to supervise of charge position by induction heating
Publikacja -
Predictive method of improvement of the generators rated power usage in inductive heating
Publikacja -
EVALUATION OF CAUSES OF CORROSION OF HEATING PIPES AND BALLAST CHAMBERS ON HLVJ INNOVATION
Publikacja..
-
Innovative optimization algorithm of variable speed pumps in district heating systems.
PublikacjaW referacie przedstawiono innowacyjny algorytm matematyczny optymalizacji pracy pomp zmienno prędkościowych w systemach ciepłowniczych. Algorytm wykorzystuje procedurę iterecyjnego wyznaczania parametrów pracy pomp, których charakterystyki są linearyzowane odcinkami w układzie dwóch współrzędnych. Do rozwiązania modelu całkowitoliczbowego zaproponowano wykorzystanie systemu GAMS. W pracy przedstawiono podstawy metodologiczne i...
-
Effect of laser heating on cavitation behaviour of Fe-Cr-Mn coating.
PublikacjaW pracy przedstawiono badania odporności kawiracyjnej napoiny Fe-Cr-Mn po obróbce laserowej polegającej na przetapianiu napoiny wiązką lasera CO2 o mocy 1000W oraz jej nagrzewaniu w stanie stałym. Rezultaty badań wskazują,że po każdym rodzaju obróbki występuje inna podatność obrobionej powierzchni do odkształceń plastycznych pod działaniem obciążeń kawitacyjnych.
-
Experimental investigation and process parameter optimization of sheet metal bending by line heating method
PublikacjaThe present study is concerned with the experimental investigation of sheet metal deforming by line heating method that incorporates the combined effect of traverse speed of the torch, thickness of the sheet metal, and the number of passes of the torch. For the numerical analysis of metal bending by line heating, the
-
Interaction of Acoustic and Thermal Modes in the Vibrationally Relaxing Gases. Acoustic Cooling
PublikacjaThe dynamic equation which governs an excess temperature associated with the thermal mode in vibrationally relaxing gas is derived. The nonlinear transfer of acoustic energy to the energy of the thermal mode in a relaxing gas causes slow variation of temperature with time. The nal dynamic equation is instantaneous. All types of sound, including aperiodic, may be considered as an acoustic source of corresponding heating or cooling....
-
FURTHER REMARKS ON THE NEO-CLASSICAL NAVIER-STOKES EQUATIONS
PublikacjaThe seminal Navier-Stokes equations have been stated yet before creation of principles of thermodynamics and the first and second laws. In the literature there is the common opinion that the Navier-Stokes equations cannot be taken as a thermodynamically correct model of “working fluid” which is able to describe transformation of “ heat” into “work” and vice versa. Therefore, in the paper, a new exposition of thermodynamically...
-
Neoclassical Navier–Stokes Equations Considering the Gyftopoulos–Beretta Exposition of Thermodynamics
PublikacjaThe seminal Navier-Stokes equations were stated even before the creation of the foundations of thermodynamics and its first and second laws. There is a widespread opinion in the literature on thermodynamic cycles that the Navier-Stokes equations cannot be taken as a thermodynamically correct model of a local "working fluid", which would be able to describe the conversion of "heating" into "working" (Carnot's type cycles) and vice...
-
Energy Security of Polish Consumers in 2004-2021
Dane BadawczeEnergy security is one of the most important components of economic security. It is influenced not only by access to energy sources and the economic situation of the state and the individual consumer. In the years 2004–2021, energy security of the individual consumer in the economic dimension significantly improved. This was due to several factors:1....
-
Modeling and optimization of chemical-treated torrefaction of wheat straw to improve energy density by response surface methodology
PublikacjaToday, torrefaction is important technique for extending the potential of biomass for improvement of energy density. The independent variables investigated for torrefaction study were temperature, retention time, acid concentration, and particle size. The experiment was designed by central composite design (CCD) method using design expert (version 11). The three dependent variables were higher heating value (HHV), energy enhancement...
-
Chapter 1. Modelling of temperature field of cylindrical pool boiling heating section
PublikacjaPoddano analizie fundamentalny problem określania temperatury powierzchni, na której zachodzi wrzenie. Rozpatrzono dwa przypadki ogrzewania sekcji: z zastosowaniem grzejnika patronowego oraz użyciem sekcji jako elementu oporowego. Sformułowano i rozwiązano zagadnienia brzegowe 1D, 2D ORAZ 3D. Przedstawiono wyniki obliczeń numerycznych z zastosowaniem MES.
-
Adsorption chiller in a combined heating and cooling system: simulation and optimization by neural networks
Publikacja -
Heating caused by a non periodic ultrasound. Theory and calculations on pulse and stationary sources.
PublikacjaPrzedstawiono teorię ewolucji ogrzewania na skutek przejścia fali akustycznej każdego typu. Przedyskutowano obliczenia na podstawie nowych wzorów dla fali impulsowej i uderzeniowej. Wzory zgadzają się z klasycznymi w wypadku fal okresowych.
-
BACTERIAL INACTIVATION VIA LASER-DRIVEN GOLD NANOPARTICLE HEATING: SIMULATION AND ANALYSIS
PublikacjaThis study utilizes CFD technique to simulate the inactivation of E. coli bacteria within a microfluidic chamber, employing gold nanoparticles irradiated by a laser beam. Employing a single-phase model, the presence of bacteria is considered by treating thermal properties in the governing equations as effective, combining those of water and bacteria using established correlations from scientific literature. The conversion of light...
-
Use of Modified Cuckoo Search algorithm in the design process of integrated power systems for modern and energy self-sufficient farms
PublikacjaIn the face of increasingly stringent pollutant emission regulations, designing an agricultural holding becomes a difficult challenge of connecting a large number of coefficients that describe an energy system of a farm in regard to its ecological and economic efficiency. One way to cope with this issue is to design an energy self-sufficient farm that integrates various technologies, including renewable energy. However, the selection...
-
On energy, exergy, and environmental aspects of a combined gas-steam cycle for heat and power generation undergoing a process of retrofitting by steam injection
PublikacjaThe paper presents a study of retrofitting of a combined heat and power (CHP) plant aimed to increase the electric to heating power ratio. The modification would involve diverting part of the steam to the gas turbine, instead of letting it go to the steam turbine, using injection technique into a combustion chamber. Therefore, two potential retrofitting approaches are analyzed: steam injection gas turbine (STIGT) and combined steam...
-
RAPESEED PELLET - A BYPRODUCT OF BIODIESEL PRODUCTION - AS AN EXCELLENT RENEWABLE ENERGY SOURCE
PublikacjaVegetable oils are renewable feedstock currently being used for production of biofuels from sustainable biomass resources. The existing technology for producing diesel fuel from plant oils, such as rapeseed, soybean, canola and palm oil are largely centered on transesterification of oils with methanol to produce fatty acid methyl esters (FAME) or biodiesel. Rapeseed pellet - crushed seed residue from oil extraction is a byproduct...
-
Numerical Simulation of Temperature Field in Steel under Action of Electron Beam Heating Source
Publikacja -
Effects of rapid heating on non-equilibrium microstructure evolution and strengthening mechanisms of titanium alloy
Publikacja -
Analysis of the Heating Process of Hydraulic Motors during Start-Up in Thermal Shock Conditions
PublikacjaConditions that prevail during harsh winters and hot summers pose a serious challenge for machine designers building devices suitable for operation in extreme weather. It is essential for the designers and the users to define the principles and conditions for the safe operation of machines and devices with hydraulic drive in low ambient temperatures. Bearing in mind the above, the author tested the hydraulic motors in thermal shock...
-
Utilization of rapeseed pellet from fatty acid methyl esters production as an energy source
PublikacjaRapeseed pellet – crushed seed residue from oil extraction is a by-product of fatty acid methyl esters production process. As other types of biomass, it can either be burned directly in furnaces or processed to increase its energetic value. Biomass is renewable, abundant and has domestic usage; the sources of biomass can help the world reduce its dependence on petroleum products, fossil coal and natural gas. Energetically effective...
-
Phase Change Thermal Energy Storage – The Experience of the Materials Preparation for the Specific Applications.
PublikacjaThermal energy storage and temperature stabilization is very important in many engineering applications. There are three kinds of thermal energy storage: sensible heat storage, latent heat storage and reversible chemical reaction heat storage. Phase change materials (PCM) absorb, store and release large amounts of energy in the form of latent heat, at constant temperature, called the transition temperature. The amount of heat...
-
Effects of CO2 and Nd:YAG Laser Remelting of the Ti6Al4V Alloy on the Surface Quality and Residual Stresses
PublikacjaThe titanium alloys are materials susceptible to tribological wear and the laser treatment can be applied in surface treatment processes to obtain for example higher hardness level. From the other side, it is important to take into consideration, that hardness increase that can be connected with cracks . The aim of this research was to investigate the effects of different lasers and the process parameters on the form and level...
-
Multicriteria Optimization Approach to Design and Operation of District Heating Supply System over its Life Cycle
PublikacjaDistrict Heating (DH) systems are commonly supplied using local heat sources. Nowadays, modern insulation materials allow for effective and economically viable heat transportation over long distances (over 20 km). In the paper a method for optimized selection of design and operating parameters of long distance Heat Transportation System (HTS) is proposed. The method allows for evaluation of feasibility and effectivity of heat transportation...
-
Analytical method for calculation of heat source temperature drop for the Organic Rankine Cycle application
PublikacjaIn the paper presented are considerations on the cooperation of the limited capacity heat source with the Organic Rankine Cycle unit. Usually the heat source providing thermal energy to the Organic Rankine Cycle (ORC) may have twofold characteristics. It can be in the form of a single phase fluid, i.e. as hot exhaust gas or hot liquid, or in some cases it may be available as a phase changing fluid, as for example, technological...
-
Innovative Railway Stations
PublikacjaIn relation to modern demographic trends, evolving technologies and environmentfriendly solutions increases the potential of rail considered as sustainable form of public transport. Contemporary tendencies of designing railway stations in Europe are focused on lowering energy consumption and reducing carbon emission. The main goal of the designers is to create a friendly and intuitive space for its users and at the same time a...
-
Determinants of the surface quality, density and dimensional correctness in selective laser melting of the Ti-13Zr-13Nb alloy
PublikacjaSelective laser melting is widely used for custom-designed elements. Successful manufacturing depends on laser treatment parameters and material features. This research aimed to determine the effects of laser power, scan time and hatch distance on surface quality, relative density and dimensional precision for cuboids made of the Ti-13Zr-13Nb alloy. The influence of energy density, energy flux and pre-heating was seen to be decisive...
-
Relevance of the EU Structural Funds’ Allocation to the Needs of Combating Air Pollution in Poland. Analysis of the Operational Programmes of Regions Threatened With Critical Air Pollution from Distributed Energy Sources
PublikacjaRecent years, the European Environmental Agency, has been reporting air quality parameters in Poland, as the poorest among all the EU countries. Despite of adoption of the EU legislation on energy efficiency and energy performance of buildings, existing legal solutions occur insufficient in reducing air pollution in Polish regions. Lack of an effective schemes supporting complex thermal renovation of buildings, exchange of inefficient...
-
Prediction of metal deformation due to line heating; an alternative method of mechanical bending, based on artificial neural network approach
PublikacjaLine heating is one of the alternative methods of forming metals and this kind of forming uses the heating torch as a source of heat input. During the process, many parameters are considered like the size of the substrate, thickness, cooling method, source power intensity, the travel speed of the power source, the sequence of heating, and so on. It is important to analyze the factors affecting the...
-
Battery Technologies in Electric Vehicles: Improvements in Electric Battery Packs
PublikacjaRestrictions on fossil fuels and related environmental pollution issues motivate many organizations and countries to set their focus on electric vehicles (EVs) rather than conventional internal combustion engine vehicles [1], [2]. EVs require an energy storage system to store converted electric power in another form of energy and then reconvert the stored energy to electric power whenever it is required. The energy stored can be...
-
Development of linear projecting in studies of non-linear flow. Acoustic heating induced by non-periodic sound
PublikacjaRównanie bilansu energii rozkłada się na sumę dwóch równań, opisujących dynamikę fali akustycznej i wywołanego przez nią ogrzewania. Nowe równanie dynamiczne stosowane jest dla opisu dźwięku nieokresowego zarówno jak okresowego. Rozpatruje się geometrię wiązkową. Omówiane są poszczególne udziały przewodnictwa cieplnego i lepkości w ogrzewaniu akustycznym. Równania stanu ośrodka propagacji są uwzględniane w najbardziej ogólnej postaci.
-
Automatic Adjustment of Integration Time in the NIR Camera for Calibrated Temperature Measurement during Inductive Heating Processes
Publikacja -
About definition of modes and magnetosonic heating in a plasma’s flow: Especial cases of perpendicular and nearly perpendicular wave vector and magnetic field
PublikacjaDynamics of hydrodynamic perturbations in a plasma depend strongly on an angle between the wave vector and equilibrium straight magnetic field. The case of perpendicular propagation is especial. There are only two (fast) magnetosonic modes since two (slow) ones degenerate into the stationary one with zero speed of propagation. This demands individual definition of wave modes by the links of hydrodynamic relations. These links are...
-
Comparative study of operation of condensing and traditional boilers equipped with the ORC module for electricity generation
PublikacjaCondensing technology applied to boilers is to make full use of thermal energy contained in the fuel. That means that additionaly the heat from condensation of exhaust gases can be used for the purposes of heating the domestic hot water and to cover the demand for central heating. The study analyzed the operation of the "traditional" boiler equipped with the ORC module as the similar arrangement but with the condensing boiler....
-
Will NILM Technology Replace Multi-Meter Telemetry Systems for Monitoring Electricity Consumption?
PublikacjaThe estimation of electric power utilization, its baseload, and its heating, light, ventilation, and air-conditioning (HVAC) power component, which represents a very large portion of electricity usage in commercial facilities, are important for energy consumption controls and planning. Non-intrusive load monitoring (NILM) is the analytical method used to monitor the energy and disaggregate total electrical usage into appliance-related...
-
Evaluating the influence of radiative heat flux on convective heat transfer from a vertical plate in air using an improved heating plate
PublikacjaThis article examines the influence of radiative heat flux on the accuracy of the results of free convective heat transfer in air. In order to carry out these tests, based on the experience gained during the operation of a plate heated on one side, compensated by a reverse heat loss flux counter-heater, a unique double-sided heating sandwich plate was designed and built, consisting of three thin epoxy resin plates reinforced with...
-
Katalizatory wykorzystywane w syntezie biodiesla
PublikacjaRising prices of electricity, conventional fuels and heating require decisive steps in the further development of technologies based on renewable energy sources. These include geothermal-; hydrothermal-; aerothermal-; and solar energy. Due to the fact that the petrochemical industry is one of the fastest growing branches of the economy, we would like to expand on the topic related to biofuels. Biodiesel is an alternative fuel similar...
-
Nuclear Co-generation: The Analysis of Technical Capabilities and Cost Estimates
PublikacjaThis paper presents a concept of the parallel connection of a nuclear power plant fitted to provide heat for district heating application, with the CHP and heat plants existing in the supply region, in this case with the heating systems of Wejherowo and Gdynia. Presented variant proposes to add heat to a nuclear power plant’s total output by supplying heat exchangers with the steam from bleeders of low pressure (LP) turbine stage...
-
A novel approach for processing CaAlSiON glass-ceramics by spark plasma sintering: Mechanical and electrical properties
PublikacjaLithium containing glassy materials can be used as solid electrolytes or electrode materials for lithium-ion batteries due to their high energy density. Conventional melt-quenched Ca11Al14Si16O49N10 glass powder containing 24 e/o N, doped with Li-ions (1, 3, and 6 wt. %) and sintered by spark plasma sintering technique (SPS) was studied. The benefits of using SPS to produce glass-ceramics are rapid heating rates compared to conventional...
-
Ekonomična efektivnist` teplovoï pompi v sistemi opalennâ = Economical efficiency of heat pump system in heating system
PublikacjaW artykule opisano wynik porównawczych obliczeń kosztów ogrzewania budynku jednorodzinnego. Porównano koszty konwencjonalnego ogrzewania z kotłem olejowym jako źródłem ciepła z kosztami ogrzewania układem hybrydowym, w którym współpracują ze sobą dwa żródła ciepła: konwencjonalny kocioł olejowy i sprężarkowa pompa ciepła. Wykonano studium parametryczne kosztów ogrzewania z wykorzystaniem metody kosztów narastających.
-
Gas Turbine Cycle with External Combustion Chamber for Prosumer and Distributed Energy Systems
PublikacjaThe use of various biofuels, usually of relatively small Lower Heating Value (LHV), affects the gas turbine efficiency. The present paper shows that applying the proposed air by-pass system of the combustor at the turbine exit causes tan increase of efficiency of the turbine cycle increased by a few points. This solution appears very promising also in combined gas/steam turbine power plants. The comparison of a turbine set operating...
-
Hydrogen production from ethanol In nitrogen microwave plasma At atmospheric pressure
PublikacjaHydrogen seems to be one of the most promising alternative energy sources. It is a renewable fuel as it could be produced from e.g. waste or bio-ethanol. Furthermore hydrogen is compatible with fuel cells and is environmentally clean. In contrast to conventional methods of hydrogen production such as water electrolysis or coal gasification we propose a method based on atmospheric pressure microwave plasma. In this paper we present...
-
Influence of Different Biofuels on the Efficiency of Gas Turbine Cycles for Prosumer and Distributed Energy Power Plants
PublikacjaThe efficiency of a gas turbine can be affected by the use of different biofuels usually with a relatively Lower Heating Value (LHV). The paper evaluates the impact of calorific value of fuel on turbine performance and analyzes the possibilities of optimizing turbine construction from the point of view of maximum efficiency for a particular fuel. The several variants of design of small power microturbines dedicated to various biofuels...
-
Assessment, optimisation and working fluid comparison of organic rankine cycle combined with negative CO2 gas power plant system
PublikacjaThis study aims to investigate the application of the Organic Rankine Cycle (ORC) as an alternative to low-pressure expansion in the negative CO2 power plant (nCO2PP). The reason for this study is that a detailed analysis of nCO2PP indicates a certain amount of waste heat present in the exhaust gas from the high-to-intermediate pressure gas turbine. Some of this energy can be used by the application of the expansion in a low-pressure...