Wyszukiwarka
Filtry
wszystkich: 337
-
Katalog
- Publikacje 283 wyników po odfiltrowaniu
- Czasopisma 13 wyników po odfiltrowaniu
- Osoby 5 wyników po odfiltrowaniu
- Wynalazki 1 wyników po odfiltrowaniu
- Zespoły Badawcze 2 wyników po odfiltrowaniu
- Kursy Online 26 wyników po odfiltrowaniu
- Oferty 1 wyników po odfiltrowaniu
- Dane Badawcze 6 wyników po odfiltrowaniu
Wyniki wyszukiwania dla: SOLA
-
Projekt belki hybrydowej 1a dla firmy H+H Polska sp. z o.o.
PublikacjaNiniejsze opracowanie stanowi projekt belki nadprożowej o długości 3,0 m o przekroju poprzecznym belki hybrydowej (beton konstrukcyjny łączony z betonem komórkowym) nawiązującej do wymiaru bloczka z betonu komórkowego firmy H+H Polska sp. z o.o. o wymiarach (szerokość × wysokość × długość): 24 × 24 × 60 cm, odmiany D600 o średniej wytrzymałości na ściskanie 3,0 MPa. Całkowita wysokość belki hybrydowej wynosi 27 cm (wraz z 3 cm...
-
Applying response surface method to optimize the performance of a divergent-chimney solar power plant
PublikacjaOne of the effective tools to generate electricity from solar energy is Divergent-chimney solar power plant (DSPP). Divergent and cylindrical chimneys of solar power plants have different performances considering turbine pressure drop ratio (ft). For the first time, the divergent angle (DA) and solar radiation (SR) interaction effects on 〖ft〗_opt are discussed through applying the Computational Fluid Dynamics (CFD) and Response...
-
Re-use of photovotaic [i.e. photovoltaic] crystalline silicon solar cells - technological possibilities
PublikacjaSystemy fotowoltaiczne są stosowane na całym świecie jako niezawodne i wydajne układy zasilania dla zastosowań przemysłowych, komunalnych i komercyjnych. Średni czas eksploatacji modułów fotowoltaicznych wynosi ponad 25 lat. Wyeksploatowane moduły oraz te, które uległy uszkodzeniu, są obecnie przeważnie składowane na wysypiskach jako odpady przemysłowe lub komunalne, np. jako szkło lub materiał rozbiórkowy, co było dopuszczalne...
-
1/f noise as a diagnostic tool for non-destructive testing of silicon solar cells
PublikacjaPrzeprowadzono badania eksperymentalne charakterystyk statycznych i szumowych krzemowych ogniw słonecznych. Wyniki wykazują możliwość wykorzystania szumu 1/f jako narzędzia diagnostycznego w testach nieniszczacych tych przyrzadów.
-
Modeling the electrical characteristics of P3HT:PCBM bulk heterojunction solar cells: Influence of the interface recombination
PublikacjaThe interface recombination of charge carriers located in the material with lower permittivity (Szmytkowski 2009 Chem.Phys.Lett. 470 123) has been implemented for the first time to calculate the electrical characteristics of the donor-acceptor P3HT:PCBM bulk heterojunction solar cell. In order to estimate the photocurrent density in this system, a simple analytical formula has been derived. We have obtained a very good agreement...
-
Nongeminate recombination in organic bulk heterojunction solar cells: Contribution of exciton–polaron interaction
PublikacjaA new model to explain nongeminate recombination in organic bulk heterojunction solar cells is presented. We suggest that the annihilation of excitons on charge carriers at the interface between donor and acceptor phases competes with the bimolecular recombination of Coulombically bound electron–hole pairs. The exciton–polaron interaction gives visible contribution to the reduction of Langevin recombination. An analytical formula,...
-
Iron-based catalysts under solar and visible radiation for contaminants of emerging concern removal
Publikacja -
Testing of PTA automatic braze-welding technology for producing absorber joints of solar collectors
Publikacja -
Technology of braze welding absorber tubes to copper foil in solar collectors by the GTA method
Publikacja -
Significant Parameters Identification for Optimal Modelling of the Harp-Type Flat-Plate Solar Collector
Publikacja -
Investigations of New Phenothiazine-Based Compounds for Dye-Sensitized Solar Cells with Theoretical Insight
Publikacja -
Effect of thienyl units in cyanoacrylic acid derivatives toward dye-sensitized solar cells
Publikacja -
Experimental investigations of prototype od solar collector on the rig equipped with artificial source of illumination
PublikacjaW pracy opisano badania eksperymentalne prowadzone w Katedrze Techniki Cieplnej Politechniki Gdańskiej, dotyczące prototypowego cieczowego kolektora słonecznego, wykonanego z organicznego tworzywa sztucznego. Badania cieplne przeprowadzono metodą porównanwczą, przy czym kolektorem odniesienia był kolektor słoneczny Aparel produkowany na rynku krajowym. W artykule opisano też stanowisko badawcze zaprojektowane i zbudowane jako moblina...
-
ANALYSIS OF THE FEATURES OF EFFECTIVE IMPLEMENTATION OF SOLAR POWER PLANTS IN LOCAL ENERGY SUPPLY SYSTEMS
PublikacjaПоказано, що відновлені джерела енергії (ВДЕ) у багатьох країнах дедалі більше домінують на ринку електроенергії, при цьому обсяги генерації електроенергії сонячними електростанціями (СЕС) останніми роками зростають рекордними темпами. Зазначено, що хоча частка ВДЕ продовжує зростати і фотоелектрична індустрія стрімко розвивається, однак галузь все ще стикається з багатьма проблемами, зокрема як продовжувати знижувати нормовану...
-
The influence of UV light on Performance of poly(methyl methacrylate) in regard to dyesensitised solar cells
PublikacjaNiskie kosztu produkcji i prosta budowa Barwnikowych Ogniw Słonecznych (ang.DSSC-Dye Sensitized Solar Cells) a także porównywalne wydajności czynią je konkurencyjnymi wsród komercyjnych technologii ogniw słonecznych. Jednym z elementów wchodzących w skład BOS jest transparentne szkło przewodzące stanowiące jego elektrody. Doskonała transparentność omozliwia zastosowanie polimeru PMMA jako substytutu transparaentnego szkła przewodzącego....
-
Air temperature trends at Mount Śnieżka (Polish Sudetes) and solar activity, 1881–2012
Publikacja -
Effect of Different Bromine Sources on the Dual Cation Mixed Halide Perovskite Solar Cells
PublikacjaRecent research has shown that perovskite solar cells with a mixed dual A-cation have much better structural stability without loss of efficiency than single cation devices. Mixed cation perovskites create a lot of questions about the salts being used for the formation of the best-quality layer. Here, we have investigated three sources of bromide in the perovskite absorption layer, using lead bromide (PbBr2), formamidinium bromide...
-
Issues relating to the efficient Application of passive solar protection in multi-family residential buildings
PublikacjaThe following article is intended to discuss the issues concerning the introduction of passive measures aimed at improving solar protection in multi-family buildings. A system of classifying these methods into two groups of solutions (architectural and material-building) was applied. The first group includes issues concerning facade design, the spatial features of which (such as loggias, balconies and other overhangs) can be treated...
-
Design of power cable lines partially exposed to direct solar radiation – special aspects
PublikacjaPower cable lines are usually buried in the ground. However, in some cases, their ending sections are mounted along the supports of overhead lines. This leads to a situation where the cables are exposed to direct solar radiation and, consequentially, overheat. The paper presents the advanced computer modelling of power cables’ heating, considering their insolation as well as the effect of wind. The temperature and current-carrying...
-
Synthesis of novel dinuclear ruthenium polypyridine dye for dye-sensitized solar cells application
PublikacjaA new dinuclear ruthenium(II) polypyridine complex has been successfully synthesized. The new compound has been characterized by spectroscopic and electrochemical methods. Its potential application as a sensitizing dye in dye-sensitized solar cells has been checked under AM 1.5 G irradiation conditions (100 mW cm−2) and its performance was compared to that of a commercially available mononuclear analogous dye. The overall light-to-electricity...
-
Magnetic field effects in dye-sensitized solar cells controlled by different cell architecture
PublikacjaThe charge recombination and exciton dissociation are generally recognized as the basic electronic processes limiting the efficiency of photovoltaic devices. In this work, we propose a detailed mechanism of photocurrent generation in dye-sensitized solar cells (DSSCs) examined by magnetic field effect (MFE) technique. Here we demonstrate that the magnitude of the MFE on photocurrent in DSSCs can be controlled by the radius and...
-
Recycling of raw materials, silicon wafers and complete solar cells from photovoltaic modules
PublikacjaPhotovoltaic modules (PVs) are an attractive way of generating electricity in reliable and maintenance-free systems with the use of solar energy. The average lifetime of photovoltaic modules is 25 to 30 years. To offset the negative impact of photovoltaic modules on the environment, it is necessary to introduce a long-term strategy that includes a complete lifecycle of all system components from the production phase through installation...
-
Ampacity of power cables exposed to solar radiation – recommendations of standards vs. CFD simulations
PublikacjaThe aim of the paper is to evaluate the ampacity of a low-voltage single power cable according to: 1) recommendations of the standard IEC 60287, 2) a Computational Fluid Dynamics method, implemented in Ansys software; and comparison of the results obtained for these two cases. Moreover, limitations of recommendations of the above mentioned standard are indicated.
-
A strategy for GPS data processing in a precise local network during high solar activity
PublikacjaThis paper presents the analyses connected with reduction of errors from ionospheric refraction using GPS data from local satellite networks. This is particularly essential during rising solar activity. The Bernese GPS Software v. 4.2 was used, as an analytical tool. The test data included measurements from a geodynamic network SUDETES situated in the Sudety Mountains across the border between the Czech Republic and Poland. A local...
-
Overheating of underground power cable line due to its partial exposition to solar radiation
PublikacjaCurrent-carrying capacity of underground power cable lines depends, among others, on thermal resistivity of the soil and cables layout: trefoil formation, flat formation with or without spacing. If conditions for heat transfer in the ground are favorable, the current-carrying capacity is relatively high. Therefore, it generates risk of the power cables overheating, if part of the cable line is located vertically in the air, to...
-
Heat recovery from the hybrid photovoltaic tile – experimental studies with the solar light simulator
PublikacjaConsidering the current development of micro-cogeneration energy sources, supported by the national prosumer policy and the act on the renewable energy sources, there is a great demand for the effective solar technologies. In this area, the photovoltaic cells with a combined conversion of the solar radiation energy into the electrical and thermal energy (PV/T cells) seem to be attractive. They are already widely available and treated...
-
Hypsometric changes in urban areas resulting from multiple years of mining activity
Publikacja -
Geomorphological and Hydrological Effects of Subsidence and Land use Change in Industrial and Urban Areas
Publikacja -
Anthropogenic enrichment of the chemical composition of bottom sediments of water bodies in the neighborhood of a non-ferrous metal smelter (Silesian Upland, Southern Poland)
Publikacja -
Dynamics of Changes in the Surface Area of Water Bodies in Subsidence Basins in Mining Areas
Publikacja -
Aqueous Mechanical Oxidation of Zn Dust: An Inventive Technique for Bulk Production of ZnO Nanorods
Publikacja -
Numerical and Analytical Investigation of Aluminium Bracket Strengthening
PublikacjaThis paper focuses on an analytical and numerical investigation of aluminium brackets used to fasten light-weight curtain walls to building facilities. The authors propose a solution to increase the load capacity of aluminium brackets by means of additional cover plates (straps). This paper also includes a short survey of literature and material properties concerning the EN AW-6060 T6 aluminium alloy. This paper suggests an initiation...
-
Simulation of perovskite-based CuI/CH3NH3PbI3/TiO2 solar cell performance
Dane BadawczeThe presented data set is part of the theoretical research on novel thin-layer lead-halide perovskite solar cells with different inorganic transparent conductive oxides used as charge transport layers. In this study CuI/CH3NH3PbI3/TiO2 model structure (Model 1) was investigated by the use of the SCAPS-1D simulation method (https://scaps.elis.ugent.be/).
-
Simulation of perovskite-based CuI/CH3NH3PbI3/SnO2 solar cell performance
Dane BadawczeThe presented data set is part of the theoretical research on novel thin-layer lead-halide perovskite solar cells with different inorganic transparent conductive oxides used as charge transport layers. In this study CuI/CH3NH3PbI3/SnO2 model structure (Model 2) was investigated by the use of the SCAPS-1D simulation method (https://scaps.elis.ugent.be/).
-
Simulation of perovskite-based CuI/CH3NH3PbI3/ZnO solar cell performance
Dane BadawczeThe presented data set is part of the theoretical research on novel thin-layer lead-halide perovskite solar cells with different inorganic transparent conductive oxides used as charge transport layers. In this study CuI/CH3NH3PbI3/ZnO model structure (Model 3) was investigated by the use of the SCAPS-1D simulation method (https://scaps.elis.ugent.be/).
-
Additive Effect of Bromides and Chlorides on the Performance of Perovskite Solar Cells Fabricated via Sequential Deposition
PublikacjaA two-step sequential deposition method has been applied to prepare the solar cells with two types of perovskites Cs0.15FA0.85Pb(I0.95Cl0.05)3 and Cs0.15FA0.85Pb(I0.95Br0.05)3. In order to obtain the perovskite layers, the different sources of bromine and chlorine atoms were used for synthesis. The performance and time stability of chloride-based photocells are worse in comparison to the bromide-based devices. It can be explained...
-
The Influence of UV Light on Performance of Poly(methyl Methacrylate) in Regard to Dye-Sensitised Solar Cells
Publikacja -
Metal doped TiO2 decorated carbon nanostructured materials as an emerging photocatalysts for solar fuels production
Publikacja -
Self-adaptive heat extraction controller for solar thermal tower operational with molten salt tanks
Publikacja -
Investigating the potential of CuSCN as hole transport layer for perovskite solar cells for applications in indoor photovoltaics
Publikacja -
Impact of TiO2 Reduction and Cu Doping on Bacteria Inactivation under Artificial Solar Light Irradiation
Publikacja -
Highly stable CsFAPbIBr perovskite solar cells with dominant bulk recombination at real operating temperatures
PublikacjaMixed-cation mixed-halide perovskite solar cells have been characterized in DC at different temperatures (from −20 °C up to 50 °C) and the time evolution of the device efficiency has been assessed using different degradation protocols (indoors and outdoors). The completely planar p–i–n structure is ITO/CuNiOx/PTAA/CsFAPbIBr/PCBM/PEI/Ag. Pristine current–voltage characteristics barely show hysteresis, at any temperature. Open circuit...
-
Comparison of ZnO:Al, ITO and carbon nanotube transparent conductive layers in flexible solar cells applications
PublikacjaW artykule zostały przetestowane różne typy transparentnych elektrod z uwagi na właściwości mechaniczne, optyczne oraz elektryczne. Wszystkie przebadane materiały zostały nałożone w postaci warstw na podłoża elastyczne. Otrzymane wyniki zostały porównane z danymi dla podłoży sztywnych.
-
The influence of anchoring group position in ruthenium dye molecule on performance of dye-sensitized solar cells
PublikacjaThe effect of anchoring group position and, in consequence, the orientation of the ruthenium dye molecule on titania surface on the performance of dye-sensitized solar cells has been studied intensively. Three model ruthenium sensitizing dyes bearing carboxylic anchoring group in ortho, meta or para position were synthesized and well characterized by spectroscopic, electrochemical, photophysical and photochemical measurements....
-
Experimental study of the use of electric car powered with stationary solar and electrochemical batteries in Northern Poland
PublikacjaThe subject of this paper is an experimental analysis of a Nissan LEAF electric car equipped with 24 kWh battery, powered from the standalone photo-voltaic (PV) charging station in Gdańsk, Poland. The calculations of charging process efficiency and range of test drives were conducted in two extreme situations (winter and summer) of sunlight and road conditions. Experiments were performed in the Laboratory of Innovative Power Technologies...
-
Analysis of the image force effects on the recombination at the donor-acceptor interface in organic bulk heterojunction solar cells
PublikacjaWe consider the influence of image force effects on the recombination at the donor-acceptor interface in organic bulk heterojunction solar cells. The conclusion is that the charge carriers of one sign located in the material with lower permittivity recombine at the boundary between donor and acceptor phases. This process competes with the recombination of opposite sign charge carriers, leading to the reduction of the Langevin-type...
-
Chemical treatment of crystalline silicon solar cells as a method of recovering pure silicon from photovoltaic modules
PublikacjaProducenci modułów PV stosują ogniwa krzemowe, wyprodukowane w różnej technologii, w efekcie czego różnią się one między sobą. Różnorodność dotyczy zarówno modułów PV, wykonanych z ogniw polikrystalicznych jak i monokrystalicznych. Różnice widoczne są zwłaszcza dla kontaktów elektrycznych. Producenci ogniw wykonują metalizację z zastosowaniem past Al, Ag lub przy jednoczesnym użyciu Al/Ag. Proces recyklingu krzemowych ogniw PV...
-
Crystalline Silicon (c-Si)-Based Tunnel Oxide Passivated Contact (TOPCon) Solar Cells: A Review
Publikacja -
The Economic Dimension of Using the Integration of Highway Sound Screens with Solar Panels in the Process of Generating Green Energy
Publikacja -
Dyes based on the D/A-acetylene linker-phenothiazine system for developing efficient dye-sensitized solar cells
Publikacja