Wyszukiwarka
Wyniki wyszukiwania dla: condensation, steam condenser
-
O strumieniu mocy w silniku lub w układzie napędowym
PublikacjaW silniku lub w układzie napędowym wielkość strumienia mocy rośnie w kierunku przeciwnym do kierunku przepływu mocy. Straty energetyczne i sprawność energetyczna silnika lub układu napędowego powinny być przedstawiane jako funkcje wielkości fizycznych niezależnych od strat. Takimi wielkościami są prędkość i obciążenie silnika. Jednakże obraz strumienia mocy w silniku lub w układzie napędowym jest przedstawiany w literaturze w formie...
-
Accuracy Investigations of Turbine Blading Neural Models Applied to Thermal and Flow Diagnostics
PublikacjaPossibility of replacing computional fluid dynamics simulations by a neural model for fluid flow and thermal diagnostics of steam turbines is investigated. Results of calculations of velocity magnitude of steam for 3D model of the stator of steam turbine is presented.
-
On power stream in motor or drive system
PublikacjaIn a motor or in a drive system the quantity of power increases in the direction opposite to the direction of power flow. Energy losses and energy efficiency of a motor or a drive system must be presented as functions of physical quantities independent of losses. Such quantities are speed and load. But the picture of power stream in a motor or in a drive system is presented in the literature in the form of traditional Sankey...
-
Model dynamic electrochemical impedance spectroscopy (DEIS) results obtained with various DC polarization rates
Dane BadawczeThe dataset contains results of model dynamic electrochemical impedance spectroscopy studies carried out on a setup of 10 diodes in series, which were connected in parallel with a condenser. The impedance data were acquired every 1 s (the analytic window length for Fourier Transform was 1 s). The model system was polarized between 0 and +8 V with DEIS...
-
Fundamentals of thermodynamics and heat transfer, W/C, GTM (WCh), sem.04, zimowy 23/24 (PG_00048767)
Kursy OnlineTable of contents presented on the course: Basic terms.The first law of thermodynamics for closed and open systems.The properties of perfect, semi-perfect and real gases.Gas rights. Thermal and caloric state equation.Thermodynamic transformations of a perfect gas.Gaseous thermodynamic cycles. The second law of thermodynamics.Steam and steam cycles.Basics of heat exchange.
-
Comparative analysis of thermodynamic cycles of selected nuclear ship power plants with high-temperature helium-cooled nuclear reactor
PublikacjaThis paper presents a comparative analysis of thermodynamic cycles of two ship power plant systems with a high-temperature helium- cooled nuclear reactor. The first of them is a gas system with recuperator , in which classical gas chamber is substituted for a HTGR reactor (High Temperature Gas-cooled Reactor) . The second of the considered cycles is a combined gas-steam system where working medium flux from gas turbine outlet...
-
Zdzisław Kowalczuk prof. dr hab. inż.
OsobyW 1978 ukończył studia w zakresie automatyki i informatyki na Wydziale Elektroniki Politechniki Gdańskiej, następnie rozpoczął pracę na macierzystej uczelni. W 1986 obronił pracę doktorską, w 1993 habilitował się na Politechnice Śląskiej na podstawie pracy Dyskretne modele w projektowaniu układów sterowania. W 1996 mianowany profesorem nadzwyczajnym, w 2003 otrzymał tytuł profesora nauk technicznych. W 2006 założył i od tego czasu...
-
Analysis of operations of combined STIG installation
PublikacjaSteam injection in gas turbines is interesting technology with good energetic and ecological properties of gas turbines. In these applications the heat of exhaust gases is used to produce steam, which is injected in the combustion chamber of a gas turbine. The steam injection increase the power and efficiency of the installation. there are some possibilities to increases the properties of STIG turbines, for example by meas of additional...
-
Revalorization of the Szewalski binary vapour cycle
PublikacjaThe aim of the paper is to revalorizate of the Szewalski binary vapour cycle by analysing thermodynamical and operational parameters of this cycle. This was carried by accessible numerical CFM (Computational Flow Mechanics) codes type, by step-by-step modeling of separates apparatus. The binary vapour cycle is providing steam as the working fluid in the high temperature part of the cycle, while another fluid - a low boiling point...
-
Moisture content during and after high- and normal-temperature drying processes of wood
PublikacjaThe aim of the article is to present the results of moisture content of wood during and after the high-temperature steam and air–steam mixture drying processes and after an open air-drying process. The knowledge of moisture content changes of wood in the process of its drying is one of the important parameters to economy drying process and to keep the quality of dried wood. Wood samples, namely, spruce (Picea abies K.) and beech...
-
Dynamic model of nuclear power plant turbine
PublikacjaThe paper presents the dynamic multivariable model of Nuclear Power Plant steam turbine. Nature of the processes occurring in a steam turbine causes a task of modeling it very difficult, especially when this model is intended to be used for on-line optimal process control (model based) over wide range of operating conditions caused by changing power demand. Particular property of developed model is that it enables calculations...
-
BADANIE EFEKTYWNOŚCI WYKRYWANIA ANOMALII PROCESOWYCH W DZIAŁANIU TURBINY PAROWEJ ELEKTROWNI JĄDROWEJ PRZY POMOCY METOD WIELOWYMIAROWEJ ANALIZY STATYSTYCZNEJ
PublikacjaW artykule przedstawiono analizę możliwości wykrywania anomalii procesowych w działaniu turbiny parowej elektrowni jądrowej przy pomocy metod wielowymiarowej analizy statystycznej. Zasymulowano symptomy dwóch rodzajów uszkodzeń turbiny parowej tj. uderzenie wodne oraz, wyciek pary z zaworu części niskoprężnej. Jako narzędzie diagnostyczne wykorzystano Metodę Składników Podstawowych PCA (z ang. Principal Component Analysis). Jako...
-
Cooperation of ORC installation with a gas boiler as a perspective co-generation system for households
PublikacjaThis paper reports tests of an innovative micro-CHP unit prototype, consisting of a traditional gas boiler and organic Rankine cycle (ORC), which incorporates original system components such as an axial vapour microturbine, evaporator and condenser. The system co-generates heat and electricity for a single household or a group of households. Electricity is only a by-product during production of heat. While testing the prototype,...
-
The influence of drying parameters on wood properties
PublikacjaResults of influence of gas-steam mixture drying process on wood mechanical properties are presented. Wood species, namely pine (Pinus sylvestris L.) and beech (Fagus silvatica L.) from the northern part of Pomerania region in Poland, were subject of steam kiln-drying process in a laboratory kiln specially arranged for that reason.
-
Combined Heat & Power Generating Systems
PublikacjaSteam cycles in combined heat and power plants. Efficiency of combined heat and power systems. Characteristics of steam-turbine CHP plants. Choice of equipment in CHP generating systems. Economic effects of combined heat and power production. Costs and energy produced CHP generating systems. Future development trends in CHP generating systems.
-
ANALIZA MOŻLIWOŚCI ZASTOSOWANIA STEROWANIA PREDYKCYJNEGO TURBINĄ PAROWĄ ELEKTROWNI JĄDROWEJ
PublikacjaArtykuł przedstawia wyniki wstępnej analizy możliwości zastosowania sterowania predykcyjnego MPC turbiną parową elektrowni jądrowej. Tradycyjnie przyjmuje się, że turbina pracuje w jednym punkcie pracy odpowiadającym jej mocy nominalnej, co pozwala na stosowanie klasycznych regulatorów PID. Synteza sterowania dla warunków zmiennego punktu pracy wymaga uwzględnienia nieliniowego charakteru procesów turbiny oraz możliwości naruszania...
-
Small Scale Gasification of Biomass and Municipal Wastes for Heat and Electricity Production using HTAG Technology
PublikacjaCombustion and gasification technology utilizing high-cycle regenerative air/steam preheater has drawn increased attention in many application areas. The process is to be realized at temperature level above ash melting point using highly preheated agent. The use of highly preheated media above 900degC provides additional energy to conversion processes and results in considerable...
-
CFD analysis of fluid flow through the labyrinth seal
PublikacjaSteam and gas turbines are some of the fundamental means of power generation. The energy efficiency of the turbines, however, is not satisfactory. Ever since the start-up of the first turbine in the world, engineers have been striving for their increased efficiency. Multiple solutions to the problem of steam loss in an operating turbine are available. The use of seals is one of them. Empirical methods or numerical calculations...
-
The influence of drying parameters on wood properties
PublikacjaThe influence of drying conditions on wood properties is presented. The classical approach was used to determine energetic effects (cutting forces and cutting power) of wood sawing process on the basis of the wood specific cutting resistance, material constant. Before mashining wood material (soft and hard) was dryied at various conditions using air at 25oC, air-steam meaxture at 80oC and steam at 110oC.
-
THE THERMODYNAMIC ANALYSIS OF THE SZEWALSKI HIERARCHIC VAPOUR CYCLE COOPERATED WITH THE SYSTEM OF HEAT RECOVERY
PublikacjaIn this paper, thermodynamic analysis of the Szewalski hierarchic vapour cycle cooperated with the system of heat recovery from exhaust gases are presented. According to that purpose, the CFM (Computation Flow Mechanics [1,3]) approach has correctly been used. The whole system consists of the first traditional steam cycle, the second organic Rankine cycle (ORC) and system of heat recovery with use of water with temperature 90...
-
Comparative study of a bottoming SRC and ORC for Joule–Brayton cycle cooling modular HTR exergy losses, fluid-flow machinery main dimensions, and partial loads
PublikacjaEnergy conversion efficiency increase in power plants with high-temperature gas-cooled reactors via implementation of the bottoming cycle was investigated under nominal and minimal thermal load of a high-temperature reactor (HTR). Heat transfer surface area and turbine outlet volumetric flow rate in bottoming cycles was also investigated. Water and two low-boiling point working fluids (ammonia and ethanol) were analyzed. Analyzed...
-
Janusz Cieśliński prof. dr hab. inż.
OsobyUrodził się 15 kwietnia 1954 r. w Słupsku. Jest absolwentem Wydziału Budowy Maszyn Politechniki Gdańskiej (1978), z którą związał całe swoje życie zawodowe. W 1986 r. obronił doktorat, w 1997 r. – habilitację, w 2006 r. – uzyskał tytuł profesora. Pełnił funkcje prodziekana ds. nauki Wydziału Mechanicznego przez dwie kadencje (2002–2008) oraz kierownika: Katedry Maszyn Przemysłu Spożywczego (2002–2006), Katedry Ekoinżynierii i...
-
Marek Dzida dr hab. inż.
OsobyUrodził się 6 sierpnia 1953 r. w Bielsku-Białej. Absolwent Instytutu Okrętowego Politechniki Gdańskiej, od 1978 r. pracuje na Wydziale Oceanotechniki i Okrętownictwa PG. W 1983 r. uzyskał tytuł doktora nauk technicznych, w 2001 r. – doktora habilitowanego. Aktualnie zatrudniony na stanowisku profesora nadzwyczajnego na PG. Pełnił funkcję prodziekana ds. kształcenia WOiO (1996–2002) oraz dziekana (2005–2012). Od 2010 r. jest kierownikiem...
-
Synthesis of compounds with C-P-P and C=P-P bond systems based on the phospha-Wittig reaction
PublikacjaA reactivity study of a β-diketiminate titanium(III) phosphanylphosphido complex [MeNacNacTi(Cl){η2-P(SiMe3)-PtBu2}] (1) towards ketones such as benzophenone, 9-fluorenone, acetophenone, cyclopentanone, cyclohexanone and cycloheptanone is reported. The reactions of 1 with aromatic ketones (without α-protons) directly lead to the Ti(III) complex [MeNacNacTi(μ2-Cl)(OSiMe3)] (5) as well as Ti(IV) complexes with the pinacol condensation...
-
Exergy analysis of a negative CO2 emission gas power plant based on water oxy-combustion of syngas from sewage sludge gasification and CCS
PublikacjaA power cycle with water-injected oxy-combustion (water cycle) is investigated by exergy analysis. It is fueled with syngas (aka. producer gas) from gasification of sewage sludge. The cycle is equipped with a spray-ejector condenser (SEC). CO2 is separated and compressed for transportation and storage. The net delivered electric power is 31% of the fuel exergy. The task efficiency is 39% when the flue gas bleed to gasification...
-
Application of Thermo-chemical Technologies for Conversion of Associated Gas in Diesel-Gas Turbine Installations for Oil and Gas Floating Units
PublikacjaThe paper considers the issue of thermo-chemical recovery of engine’s waste heat and its further use for steam conversion of the associated gas for oil and gas floating units. The characteristics of the associated gas are presented, and problems of its application in dual-fuel medium-speed internal combustion engines are discussed. Various variants of combined diesel-gas turbine power plant with thermo-chemical heat recovery are...
-
Comparative study of operation of condensing and traditional boilers equipped with the ORC module for electricity generation
PublikacjaCondensing technology applied to boilers is to make full use of thermal energy contained in the fuel. That means that additionaly the heat from condensation of exhaust gases can be used for the purposes of heating the domestic hot water and to cover the demand for central heating. The study analyzed the operation of the "traditional" boiler equipped with the ORC module as the similar arrangement but with the condensing boiler....
-
Twin volute admission as an alternative inlet configuration for a steam tu- rbine.**2002, 164 s. 155 rys. bibliogr. 14 poz. maszyn. Podwójna spirala zasilająca jako alternatywny wlot do turbiny parowej. Rozprawa doktorska /2002.06.05/. PG, Wydz. Mechaniczny. Promotor: prof. dr hab. inż. R. Puzyrewski.
Publikacja.
-
Exergy analysis of the Szewalski cycle with a waste heat recovery system
PublikacjaThe conversion of a waste heat energy to electricity is now becoming one of the key points to improve the energy efficiency in a process engineering. However, large losses of a low-temperature thermal energy are also present in power engineering. One of such sources of waste heat in power plants are exhaust gases at the outlet of boilers. Through usage of a waste heat regeneration system it is possible to attain a heat rate of approximately...
-
LEGAL ASPECTS OF ELECTRIC ENERGY GENERATION IN A FLOATING POWER PLANT
PublikacjaThis paper discusses the characteristics of pollution and legal regulations governing investment projects affecting the environment. It describes a combined system of a compression ignition engine and a steam turbine, whose aim, when placed on a floating platform, is to produce electric energy in a so-called distributed generation system. Such a system involves a reciprocating internal combustion engine and a connected steam turbine...
-
Applications of Alkanethiols in Organic Synthesis
PublikacjaThis manuscript is an update to the earlier Science of Synthesis contribution describing methods for the synthesis of alkanethiols. Thiols can be converted into sulfonic, sulfinic, sulfenic acid and their derivatives, sulfides, disulfides, polysulfides, sulfonium salts, and thiiranes, etc. These transformations are accomplished by nucleophilic displacement or addition, oxidation, condensation, or coupling reactions involving thiol...
-
Metal ion directed template synthesis using 2-acetyl-1,3-indandione and ethylenediamine: steric and electronic restrictions
PublikacjaA template synthesis using 2-acetyl-1,3-indandione and ethylenediamine results in formation of octahedral Ni complex, whose crystal structure has been resolved using single crystal X-ray diffraction. The structure indicates that only exocyclic enolic oxygen atom of the triketone takes part in the condensation with ethylenediamine.
-
Determination of Moisture Content Profiles of Spruce Wood After High Temperature Process and Air Drying
PublikacjaThe results of moisture content of wood after the process of its drying under high temperature conditions and air drying are presented. Wood samples, namely spruce (Picea abies Karst.) from the northern part of Pomerania region in Poland, were subject of steam and air drying.The aim of experiments was to measure moisture content of wood in its cross sections using moisture meter WRD-100. The samples of thickness 70 mm and length...
-
Możliwości ograniczenia zużycia energii napędowej urządzeń przez optymalizację doboru wymienników ciepła, właściwą konfigurację i kontrolę przepływu płynów roboczych
PublikacjaArtykuł poświęcony możliwości ograniczenia zużycia energii napędowej urządzeń na drodze optymalizacji doboru wymienników ciepła, właściwej konfiguracji i kontroli przepływu płynów roboczych. Przedstawiono w nim ocenę zużycia energii w systemach energetycznych o największej energochłonności w realiach Polski. Zwrócono uwagę na możliwość wykorzystania wymienników ciepła o wysokiej efektywności dla zmniejszenia oporu przenoszenia...
-
ANALYSIS OF THE IMPACT OF MASS FLOW EXTRACTION ON THE CHANGE OF PARAMETERS IN A LABYRINTH SEAL USING THE STODOLA METHOD
PublikacjaLabyrinth seals are an important element of a steam turbine set design. The use of diagnostic extraction makes it possible to control the operation of a seal by providing information on the thermodynamic parameters along the length of the seal. Diagnostic extraction has a considerable impact on the change of the parameters, the amount of the extracted mass. This article describes the dependence of pressure in the clearance downstream...
-
ANALYSIS OF THE IMPACT OF MASS FLOW EXTRACTION ON THE CHANGE OF PARAMETERS IN A LABYRINTH SEAL USING THE STODOLA METHOD
PublikacjaLabyrinth seals are an important element of a steam turbine set design. The use of diagnostic extraction makes it possible to control the operation of a seal by providing information on the thermodynamic parameters along the length of the seal. Diagnostic extraction has a considerable impact on the change of the parameters, the amount of the extracted mass. This article describes the dependence of pressure in the clearance downstream...
-
Cutting power estimation of the bandsawing process of beech wood (Fagus sylvatica L.) dried in three operating modes
PublikacjaIn this paper the predicted values of cutting power for bandsawing machine (ST100R, f. Stenner), which is located at the sawmill company Complex in Dziemiany, were presented. The values of cutting power were forecasted for beech wood (Fagus sylvatica L.), from the northern part of Pomerania region in Poland, which was dried in three operating modes: BKP - air drying at 25oC, BKS - air-steam mixture drying at 80oC, BKW - steam drying...
-
Conditions for increasing the recognition of degradation in thermal-flow diagnostics, taking into account environmental legal aspects
PublikacjaThe ever-increasing demand for electricity and the need for conventional sources to cooperate with renewable ones generates the need to increase the efficiency and safety of the generation sources. Therefore, it is necessary to find a way to operate existing facilities more efficiently with full detection of emerging faults. These are the requirements of Polish, European and International law, which demands that energy facilities...
-
Dariusz Mikielewicz prof. dr hab. inż.
OsobyDariusz Mikielewicz – urodził się 6 lutego 1967 roku w Gdańsku, w 1985r. zdał pomyślnie egzaminy wstępne na Wydział Budowy Maszyn Politechniki Gdańskiej, który ukończył z wynikiem bardzo dobrym w 1990 roku na specjalności Maszyny i Urządzenia Energetyczne. Zainteresowania pracą naukową skłoniły go do podjęcia badań na University of Manchester na wydziale mechanicznym i energetyki jądrowej (Mechanical and Nuclear Engineering Department)...
-
High-efficient, zero-emission energy production
PublikacjaThis paper presents innovative thermodynamiccycles with high-efficient, zero-emission energy production. The main aim of this work is to show the role of nano-phenomena in the enhancement of the power of thermodynamic cycles. For that purpose, the cycles using oxy-combustion and spray ejected condensation are first studied and, secondly hybrid cycles using fuel cells and gas turbines are presented. The role of nano-phenomena in...
-
Giant Nernst effect in the incommensurate charge density wave state of P4W12O44
PublikacjaWe report the study of Nernst effect in quasi-low-dimensional tungsten bronze P4W12O44 showing a sequence of Peierls instabilities. We demonstrate that both condensation of the electronic carriers in the charge density wave state and the existence of high-mobility electrons and holes originating from the small pockets remaining in the incompletely nested Fermi surface give rise to a Nernst effect of a magnitude similar to that...
-
Efficient Method for the Synthesis of Functionalized Basic Maleimides
PublikacjaA three-step procedure involving Diels-Alder condensation of maleic anhydride with furane, formation of N-substituted imide upon reaction with appropriate diamine and a final retro Diels-Alder regeneration of the maleic carbon-carbon double bond is proposed for an unequivocal synthesis of N-substituted basic maleimides. The novel method is characterized by mild reaction conditions, easy work-up, high yields and no need for additional...
-
THE EFFECT OF WOOD DRYING METHOD ON THE GRANULARITY OF SAWDUST OBTAINED DURING THE SAWING PROCESS USING THE FRAME SAWING MACHINE
PublikacjaThe experimental results of the study focused on the effect of drying processes of warm air drying at the temperature of 6580°C and warm air-steam mixture drying at the temperature of 105°C of pine and beech wood to the size of sawdust grains created by cutting using RPW 15M frame saw is presented in the paper. Particle size analysis of dry sawdust was performed using two methods - screening method and optical method based on...
-
Calculations of labyrinth seals with and without diagnostic extraction in fluid-flow machines
PublikacjaLabyrinth seals are essential components of steam turbine unit constructions. Two types of labyrinth seals can be named, the first of which is the seal without diagnostic steam extraction, and the second – with extraction. The distribution of flow parameters along the packing is affected remarkably by the average seal clearance. The presence of diagnostic extraction leads to the equation system which is determinable and can be...
-
Analysis of the possibility of increasing thermal-electric energy conversion ratio in CHP units based on micro gas turbine
PublikacjaThe aim of this paper is to analyze the possibility of increasing thermal energy to electricity conversion efficiency in combined heat and power (CHP) units based on micro gas turbine during low heat demand periods. At the beginning sustainable development postulates under power engineering are explained. Next micro CHP as part of distributed generation idea is presented. The main part of the article is based on results of thermodynamic...
-
Influence of drying mode and feed per tooth rate on the fine dust creation in pine and beech sawing on a mini sash gang saw
PublikacjaThe experimental results of the study focused on the effect of drying processes of modified air drying and warm air steam mixture drying of pine and beech wood on the size of sawdust particles created in cutting using PRW-15M sash gang saw, are presented in the paper. Particle size analysis of dry sawdust was performed using two methods—sieving method and laser diffraction analysis. The results showed that the drying process did...
-
Investigation of the Combustion Processes in the Gas Turbine Module of an FPSO Operating on Associated Gas Conversion Products
PublikacjaIn this paper, we consider the issue of thermo-chemical heat recovery of waste heat from gas turbine engines for the steam conversion of associated gas for offshore vessels. Current trends in the development of offshore infrastructure are identified, and the composition of power plants for mobile offshore drilling units and FPSO vessels is analyzed. We present the results of a comparison of power-to-volume ratio, power-to-weight...
-
Alkanethiolates of Group 1,2, and 13-15 Metals
PublikacjaThis manuscript is an update to the earlier Science of Synthesis contribution describing methods for the synthesis of alkanethiolates of group 1, 2, and 13-15 metals. Alkanethiolates can be converted into S-alkyl thiocarboxylic acid esters, 1-thioglycosides, S-alkyl thiosulfinates, tetrahydro-1,4-thiazine-3-ones, sulfides, disulfides, sulfonium salts, dithioacetals and dithioketals, etc. These transformations are accomplished by...
-
Experimental investigations and simulations of the microturbine unit with permanent magnet generator
PublikacjaIn dispersed power generation, low power devices are used for local combined generating of heat end electric power. There are developing concepts of micropower plants with electric generators driven by steam or gas microturbines. The paper presents the results of an experimental investigations of the microturbine set consists of the turbine with partial admission, permanent magnet generator and three phase AC-to-DC rectifier. The...
-
High temperature corrosion of evaporator tubes with thermal sprayed coatings
PublikacjaDegradation examinations of outer surface of low-emission steam boiler evaporator tubes are presented in the paper. Metallographic evaluation of scale morphology, its micro sites chemical composition analysis and distribution of elements on cross sections have been performed. Water-wall tubes were exposed in steam boiler for up to two years period. Common tubes made of 16Mo3 steel suffered sulphide and molten salts corrosions....