Wyszukiwarka
Filtry
wszystkich: 1604
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: HEAT-RESISTIVE STEELS
-
The In-House Method of Manufacturing a Low-Cost Heat Pipe with Specified Thermophysical Properties and Geometry
PublikacjaVarious types of heat pipes are available to purchase off the shelf, from various manufacturers, but most of them have strictly defined geometry and technical parameters. However, when there is a need to use a heat pipe (HP) with an unusual size and shape or working conditions other than the standard ones, it becomes very costly to order them from manufacturers, especially in small quantities, and only a few producers are willing...
-
Numerical single-phase modeling of turbulent flow and heat transfer of nanofluids
PublikacjaIn this work, Nusselt number and friction factor are calculated numerically for turbulent pipe flow (6 000< Re < 12 000) with constant heat flux boundary condition using nanofluids. The nanofluid is modelled with the single-phase approach and the simulation results are compared with published experimental data.
-
Correlation between Compressive Strength and Heat of Hydration of Cement Mortars with Siliceous Fly Ash
PublikacjaThis paper presents the results of calorimetric and strength tests of mortars with ordinary Portland cement and two substitution rates (10 and 20%) of cement by siliceous fly ash. The prepared samples were cured under isothermal conditions at four different temperatures: 23, 33, 43 and 53 °C. Heat of hydration was measured using an isothermal calorimeter dedicated to monitor the hydration process of cementitious composites such...
-
Particulate Matter Production of Small Heat Source Depending on the Bark Content in Wood Pellets
PublikacjaWood pellets as biofuel are more and more used in small heat sources in Europe. Standard wood pellets are produced from wood sawdust without bark. The paper deals about the impact of bark in wood pellets on their properties and combustion process. Special attention in this work is paid to production of particulate matter during combustion of wood pellets depending on bark content. There were experimentally produced spruce wood...
-
Heat Transfer in Adsorption Chillers with Fluidized Beds of Silica Gel, Zeolite, and Carbon Nanotubes
Publikacja -
Heat Transfer-Asian Research
Czasopisma -
Frontiers in Heat and Mass Transfer
Czasopisma -
Interfacial Phenomena and Heat Transfer
Czasopisma -
Optimization of combined heat and power (CHP) market allocation: The case of Poland
PublikacjaCombined heat and power (CHP), that is production of electricity and useful heat in a single thermodynamic process, is a way of primary energy saving and emission reduction. Therefore, promotion of the electricity from high-efficiency cogeneration (CHP-E) was encouraged in the European Union. However, CHP-E promotion mechanisms proved low effectiveness in certain countries, like Poland, where the prices of certificates of origin...
-
Heat Transfer of the Multicolor-Laser-Sources-Irradiated Nanoparticles in Reference to Thermal Processes
PublikacjaUnlike the standard materials, metallic nanoparticles offer enhancing the heat convertion rate which implies the maximum and average temperature boost significantly in the considered system. The work’s purpose is to examine heat transfer in the metallic nanoparticles which have been deposited on a glassy substrate, enabling the nanostructures thermoablation. Furthermore, the functionalized substrate is irradiated with multicolor-laser-sources,...
-
Selected problems of heat and mass transfer
Kursy Online -
Numerical methods in heat and fluid flow
Kursy OnlinePrzedmiot odnosi się do bilansu masy pędu i energii w ujęciu 0D i 3D.
-
Numerical methods in heat and fluid flow
Kursy OnlinePresentation of issues concerning mathematical modelling of power installations, including thermodynamic cycles and selected devices of power installations using commercial codes, so that the student is able to properly model the process and interpret the results. Presentation of capabilities of CFD code.
-
Selected problems of heat and mass transfer
Kursy Online -
Numerical methods in heat and fluid flow
Kursy OnlinePrzedstawienie zagadnień dotyczących modelowania urządzeń instalacji energetycznych, w tym obiegów cieplnych termodynamicznych oraz wybranych urządzeń instalacji energetycznych przy użyciu kodów komercyjnych. Przedstawienie możliwości obliczeniowych kodu obliczeniowego typu CFD.
-
Effect of the inclination angle of the condenser on the heat transfer coefficient value – experimental study
PublikacjaWhen considering problem of the condensation of the refrigerant in a flow inside channel, one needs to pay attention to the shape of its cross-section, the hydraulic diameter, the channel length as well as the orientation of the channel axis in space (horizontal, vertical, inclined). This paper presents an experimental study concerning the effect of the inclination angle of the condenser with a single coil pipe on the heat transfer...
-
Characterisation of the interfacial heat transfer coefficient in hot stamping of titanium alloys
Publikacja -
Heat Transfer
Czasopisma -
Pressure drop and heat transfer during boiling and condensation at subcritical region
PublikacjaMost of the data presented in the literature relate to saturation temperatures in the range - 20°C to 40°C due to the application in refrigeration technology. There is necessity to extend databases to higher values of saturation temperature due to new applications such as Organic Rankine Cycle and high temperature heat pumps. Only few papers contain data for high reduced pressure for low boiling point liquids. This paper focus...
-
Pressure drop related to flow maldistribution in a model minichannel plate heat exchanger
PublikacjaThe paper describes the issues related to the pressure drop that accompanies the phenomenon of maldistribution of working fluid between the channels of a model minichannel plate heat exchanger. The research concerns a single exchanger's plate containing 51 (in every geometry) parallel rectangular minichannels of hydraulic diameters 461 µm, 571 µm, 750 µm and 823 µm. In addition, the more complex geometry has been investigated,...
-
Two-phase optimizing approach to design assessments of long distance heat transportation for CHP systems
PublikacjaCogeneration or Combined Heat and Power (CHP) for power plants is a method of putting to use waste heat which would be otherwise released to the environment. This allows the increase in thermodynamic efficiency of the plant and can be a source of environmental friendly heat for District Heating (DH). In the paper CHP for Nuclear Power Plant (NPP) is analyzed with the focus on heat transportation. A method for effectivity and feasibility...
-
An improved method for flow boiling heat transfer with account of the reduced pressure effect
PublikacjaIn the paper are presented the results using the authors own model to predict heat transfer coefficient during flow boiling. The model has been tested against a large selection of experimental data to investigate the sensitivity of the in-house developed model. In the work are presented the results of calculations obtained using the semi-empirical model on selected experimental flow boiling data of the refrigerants: R134a, R1234yf,...
-
Photovoltaic Roof Tiles: The Influence of Heat Recovery on Overall Performance
PublikacjaA photovoltaic (PV) roof tile serves both as a roofing material and as an electricity-producing surface. The main aim of the present study was to increase the overall system efficiency of PV tiles by using heat recovery. The chosen strategy was two-fold: determine the operational efficiency of PV tiles and optimize construction to increase the cooling effect when using air as the working medium. A detailed experimental study was...
-
High-quality Experiment Dedicated to microGravity Exploration, Heat Flow and Oscillation Measurement from Gdańsk
PublikacjaIn this paper we propose HEDGEHOG (High-quality Experiment Dedicated to microGravity Exploration, Heat flow and Oscillation measurement from Gdańsk) REXUS experiment to investigate vibrational and heat flow phenomena during the whole (ascent, microgravity phase, descent and recovery) flight of a sounding rocket. First, a proposed system of cantilever beams is discussed to study dynamic behaviour of dummy payload. Dimensioning has...
-
Study on Microstructural Characterization, Mechanical Properties and Residual Stress of GTAW Dissimilar Joints of P91 and P22 Steels
PublikacjaThis article deals with the dissimilar joining of two different grade Cr-Mo steel (2.25Cr-1Mo: P22 and modified 9Cr-1Mo: P91) for power plant application. The dissimilar butt-welded joint was produced for conventional V groove design by using the gas tungsten arc welding (GTAW) process with the application of an ERNiCrMo-3 Ni-based super alloy filler. A microstructure characterization was performed to measure the inhomogeneity...
-
Experimental investigation on straight and u-bend double tube heat exchanger with active and passive enhancement methods
PublikacjaAuthors in this work want to demonstrate the possibility to increase the heat transfer efficiency by using simple wire coil inserts to create turbulent flow in the boundary layer as well as air blowing into the annulus of the pipe. In the study, Wilson plot approach was applied in order to estimate heat transfer coefficients for all heat exchanger (HX) configurations. The study focuses on experimental values of heat transfer coefficient...
-
Effect of asymmetric fluid flow distribution on flow boiling in a microchannel heat sink – An experimental investigation
PublikacjaFlow boiling in microchannels is emerging as an exclusive cooling solution for miniaturized high-power electronic devices alongside having other high heat flux applications. Size miniaturization at microscale strangely increases heat transfer performance as well as flow boiling instabilities. Many flow boiling instabilities are interrelated and result from imperfect hydrodynamic conditions. One of such problems is flow maldistribution among...
-
Analysis of Organic Rankine Cycle efficiency and vapor generator heat transfer surface in function of the reduced pressure
PublikacjaIn the paper presented is analysis of the influence of reduced pressure on efficiency and heat transfer area of vapor generator of Organic Rankine Cycle (ORC) in case of subcritical and supercritical parameters of operation. Compared are two cases of subcritical and supercritical ORC featuring a similar arrangement of heat source supply and heat removal, that is featuring the same temperatures of working fluid before the turbine,...
-
Experiment-Based Study of Heat Dissipation from the Power Cable in a Casing Pipe
PublikacjaThe paper deals with the important challenges in terms of electricity transmission by means of underground cable lines. The power cable’s performance is characterized by an ampacity that represents its maximum electric current-carrying capacity. The ampacity of power cables depends on their ability to diffuse the heat generated by the current flow into the environment. In the performed research, the analysis of the efficiency of...
-
Thermal and economic investigation of straight and U-bend double tube heat exchanger with coiled wire turbulator
PublikacjaExperimental research has been carried out for four individual heat exchanger constructions, i.e., plain double tube, turbulized double tube, plain U-bend and U-bend with turbulator. Tests were made for the water-water system. The study covered a wide measuring range, i.e., Re = 800–9000 – on the shell side, for a constant cold water temperature of 9 ◦C and hot water of 50 ◦C. The heat exchangers were made from copper tubes with...
-
Turbulent heat transfer in thin liquid films at low and high heat fluxes
PublikacjaW pracy przedstawiono rozważania turbulentnej wymiany ciepła w cienkich filmach cieczowych powstałych w wyniku uderzenia strugi przy małych i dużych strumieniach ciepła. W ostatnim przypadku może dojść do wrzenia filmu cieczowego. Oba zjawiska zamodelowano i uzyskano odpowiednie rozkłady temperatury i pedkosci.
-
Prediction of flow boiling heat transfer coefficient for carbon dioxide in minichannels and conventional channels
PublikacjaIn the paper presented are the results of calculations using authors own model to predict heat transfer coefficient during flow boiling of carbon dioxide. The experimental data from various resea rches were collected. Calculations were conducted for a full range of quality variation and a wide range of mass velocity. The aim of the study was to test the sensitivity of the in-house model. The results show the importance of taking into...
-
Analysis of possibility and purposefulness of application of waste-heat boilers to trailing suction hopper dredgers
PublikacjaThis paper presents an analysis of possibility and purposefulness of application of waste-heat boilers to trailing suction hopper dredgers. Using results of own operational research on dredgers this author determined thermal power demand for six hypothetical trailing suction hopper dredgers of various size, at accounting for a type of power system and kind of fuel combusted by dredger's power plant. By means of basic indices of...
-
Heat and mass transfer in lack of gravity
Kursy Online -
Heat and mass transfer in lack of gravity
Kursy Online -
Experimental Investigation of Free Convection Heat Transfer from Horizontal Cylinder to Nanofluids
PublikacjaThe results of free convection heat transfer investigation from a horizontal, uniformly heated tube immersed in a nanofluid are presented. Experiments were performed with five base fluids, i.e., ethylene glycol (EG), distilled water (W) and the mixtures of EG and water with the ratios of 60/40, 50/50, 40/60 by volume, so the Rayleigh (Ra) number range was 3 104 Ra 1.3 106 and the Prandtl (Pr) number varied from 4.4 to 176....
-
A new method for determination of flow boiling heat transfer coefficient in conventional diameter channels and minichannels
PublikacjaW pracy przedstawiono rozważania związane z modelowaniem wrzenia w przepływie w kanałach o średnicach konwencjonalnych, małych i minikanałach. Przedstawiono przegląd podejść do modelowania wymiany ciepła i w tym świetle przedstawiono oryginalne podejście autora. W przeciwieństwie do innych podejść metoda autora ma zastosowanie zarówno do kanałów o średnicach konwencjonalnych i minikanałach. Przedstawiono zadowalające porównania...
-
Microstructure and corrosion behaviour of carbon steel and ferritic and austenitic stainless steels in NaCl solutions and the effect of p-nitrophenyl phosphate disodium salt
PublikacjaThe microstructure and corrosion behavior of carbon steel (CSA516) and ferritic (SS410) and austenitic (SS304L) stainless steels were studied and compared. Corrosion tests were carried out in 0.5 M NaCl solutions. Rates of corrosion were monitored based on weight loss, Tafel extrapolation and linear polarization resistance (LPR) methods. Rates of corrosion were ranked following the order: CSA516 >> SS410 > SS304L. The impact of...
-
Electrochemical investigations of stainless steels used in flue‐gas desulphurization units
Publikacja -
High temperature corrosion of stainless steels for Solid Oxide Fuel Cells
PublikacjaW pracy przedstawiono wyniki korozyjności wysokotemperaturowej stali litych i porowatych stosowanych w tlenkowych ogniwach paliwowych.
-
Investigations into tendency to stress corrosion of joints welded in austenitic and duplex steels
PublikacjaPrzedstawiono wyniki badań spawanych złączy różnoimiennych wykonanych ze stali austenitycznej oraz typu duplex 2205. Badania podatności do korozji naprężeniowej złączy wykonano metodą odkształcania z małą prędkością. Próby przeprowadzono w środowisku obojętnym oraz agresywnym (MgCl2).
-
Corrosion and hydrogen intake for some Cr-Mn steels in liquid hydrocarbons
PublikacjaStal 34HNM i 26H2MF, poddana różnym obróbkom cieplnym wykazała skłonność do korozji naprężeniowej przy pomiarach ze stałą szybkością rozciągania (10-6s-1) i pomiarach niskocyklowego zmęczenia, wykonanych w paliwie kotłowym. Mechanizm korozji naprężeniowej określono jako kruchość wodorowa, co zostało potwierdzone w pomiarach pochłaniania wodoru z tych środowisk. Jako możliwe źródła wnikania wodoru do stali omówiono procesy korozyjne,...
-
Stress corossion cracking susceptibility of dissimilar stainless steels welded joints
PublikacjaW artykule przedstawiono wyniki badań odporności na naprężeniowe pękanie korozyjne złączy różnoimiennych stali odpornych na korozję; austenitycznej 316L oraz typu duplex 2205. Badania próbek przeprowadzono techniką odkształcania z małą prędkością w agresywnym środowisku roztworu chlorku magnezowego. Wyniki badań korozyjnych uzupełniono analizą metalograficzną z obszarów przełomów.
-
Introductory Chapter: Why Austenitic Stainless Steels are Continuously Interesting for Science?
Publikacja -
Laser Surface Treatment of Sintered Stainless Steels for Wear Resistance Enhancement
Publikacja -
Creep rupture study of dissimilar welded joints of P92 and 304L steels
PublikacjaThe present work investigates the high-temperature tensile and creep properties of the dissimilar metal weld joints of 304L austenitic stainless steel (SS) and P92 creep strength-enhanced ferritic-martensitic (CSEF/M) steel under diferent testing condition. Thermanit MTS 616 fller rod (P92 fller) and the multi-pass tungsten inert gas (TIG) welding process were used to create the dissimilar weld connection. The ultimate tensile...
-
The effect of the temperature change rate on determination of the criticalpitting temperature of stainless steels
PublikacjaPrzedstawiono wyniki badań wpływu szybkości zmian temperatury na wyznaczaną krytyczną temperaturę korozji wżerowej. Badania stali 316L przeprowadzono metodą termometrii cyklicznej. Stwierdzono, że zwiększenie szybkości zmian temperatury związane jest ze zwiększeniem wyznaczonej temperatury krytycznej. Zależność krytycznej temperatury korozji wżerowej od szybkości korozji ma charakter liniowy. Wartości krytycznej temperatury korozji...
-
Hydrogen-enhanced stress corrosion cracking in low alloy steels in seawater
PublikacjaBadano podatność stali niskostopowych w wodzie morskiej w warunkach polaryzacji katodowej. Stwierdzono spadek czasu do zniszczenia, energii zniszczenia i przewężenia ze wzrostem potencjału katodowego. Wykazano znaczącą korelację między stopniem degradacji wodorowej a stężeniem wodoru dyfuzyjnego.
-
Microstructural aspects of hydrogen degradation of the 26H2MF and 34HNM constructional alloy steels
PublikacjaPodatność na degradację wywołaną przez wodór, dwóch gatunków polskich stali konstrukcyjnych stopowych: 26H2MF i 34HNM, określano przy pomocy próby powolnego rozciągania. Mierzono następujące parametry: energię pękania, wydłużenie, wytrzymałość na rozciąganie i przewężenie. Degradację stali obserwowano w 0,01M kwasie siarkowym przy gęstości prądu 20 mA/cm2 wraz z rodzajem przełomów. Poziom degradacji był zgodny z ilością wodoru...
-
Influence of deformation velocity on mechanical properties of high strength structural steels.
PublikacjaW referacie przedstawiono wyniki badań własności mechanicznych stali wysokiej wytrzymałości przeznaczonych na spawane konstrukcje okrętowe w zależności od prędkości odkształcenia. Badania były prowadzone w Akademii Marynarki Wojennej oraz w Politechnice Gdańskiej przy współudziale Uniwersytetu Technicznego w Rostocku podczas opracowywania charakterystyk tych stali dla potrzeb polskiego przemysłu okrętowego. Uwzględnienie obciążeń...