Filtry
wszystkich: 769
-
Katalog
Wyniki wyszukiwania dla: MODERN MATERIALS/GFRP COMPOSITE/FOOTBRIDGES/DYNAMIC CONSTRUCTION
-
Sustainable utilization of copper post-flotation waste in cement composites
PublikacjaThe current way of managing the copper ore flotation waste is by placing it in waste neutralization facilities. However, flotation waste has great potential in application in cement composites. The article presents the detailed characteristics of post-flotation waste (PFW) and three types of cements: CEM I, CEM II/B-V, and CEM III/A, 42.5 MPa class. The post-flotation waste added for 20% of the cement mass increase the water demand...
-
Impact and stretching standardized tests as useful tools for assessment of viscoelastic behavior for highly rubberized asphalt binder
PublikacjaAsphalt binder is generally identified as a brittle material at low service temperature or under high-speed load, and the brittleness becomes serious after weathering aging. Improving the toughness of asphalt binder through adding high-content of crumb tire rubber is an efficient method to solve this problem. Devulcanized rubber modified asphalt binder (DRMA) with different contents (15–40%) of devulcanized rubber (DR) were prepared...
-
Simple empirical formula to estimate the main geomechanical parameters of preplaced aggregate concrete and conventional concrete
PublikacjaPreplaced aggregate concrete (PAC) or two-stage concrete is a specific type of concrete successfully employed in many projects including underwater concrete structures, massive concrete structures, structures made of reinforced concrete, and improvement of concrete structures. PAC is significantly different than the conventional concrete. In this type of concrete, aggregates are initially poured into the mold, the voids between...
-
Preliminary study of linear viscoelasticity limits of cold recycled mixtures determined in Simple Performance Tester (SPT)
PublikacjaThe publication presents methodology developed for determination of linear viscoelasticity limits for cold recycled mixtures with cement and bituminous emulsion using Simple Performance Tester (SPT). Methodology was verified on reference materials (PCV and steel dummy specimens, cement concrete and asphalt concrete) to comply with elasticity and viscoelasticity theory. The developed methodology enabled determination of linear viscoelasticity...
-
Experimental and analytical analysis of punching shear in flat slabs supported on column topped with concrete head
PublikacjaAn experimental laboraatory test of the two series of slab-column elements topped with drop panels of varying sizes is described in this paper. The scope of the paper is to investigate the influence of the drop panel size and stiffness on the behaviour of the connection between the flat slab and the column topped by the concrete head. The impact of the head size and stiffness is analysed analytically and experimentally. The experimental...
-
Development and application of asphalt binder relaxation test in different dynamic shear rheometers
PublikacjaIn this study, a novel relaxation test is proposed to evaluate asphalt binder low temperature properties using a Dynamic Shear Rheometer (DSR) with parallel plates of 4 mm in diameter. Three rheometers from three different manufacturers are used to analyze seven asphalt binders. Different material parameters are derived which are useful to evaluate and discriminate different asphalt binders. Test results of all three instruments...
-
FEM and experimental investigations of concrete temperature field in the massive stemwall of the bridge abutment
PublikacjaThe paper deals with the prediction of early-age concrete temperature of cast-in-place stemwall of the bridge abutment. The considered object is an arch bridge located in Gda´nsk. In the case of massive structures, it is particularly important to not exceed the temperature difference between the core and the concrete surface. Too high temperature gradient generates an increase in thermal stresses, what could be the reason of exceeding...
-
Modification of thermal and rheological characteristics of bitumen by waste PET/GTR blends
PublikacjaWaste poly(ethylene terephthalate) (wPET)/ground tire rubber (GTR) blends with variable compositions were applied as low-cost modifiers into bitumen and their performance has been evaluated via morphological, thermal and rheological analyses. Depending on the weight ratio of wPET/GTR, dispersion of single/composite domains of waste polymers in the bitumen has promoted the interaction between bitumen and blend components. Fourier...
-
Improving asphalt pavement intelligent compaction based on differentiated compaction curves
Publikacja -
An experimental study of self-sensing concrete enhanced with multi-wall carbon nanotubes in wedge splitting test and DIC
PublikacjaConcrete is the worldwide most utilized construction material because of its very good performance, forming ability, long-term durability, and low costs. Concrete is a brittle material prone to cracking. Extensive cracking may impact durability and performance over time considerably. The addition of a small amount of carbon nanotubes (CNT) increases the concrete’s overall electrical conductivity, enabling internal structure...
-
Potential use of granite waste sourced from rock processing for the application as coarse aggregate in high-performance self-compacting concrete
Publikacja -
Asphalt concrete subjected to long-time loading at low temperatures – Deviations from the time-temperature superposition principle
PublikacjaThe article presents the observed deviations from the time-temperature superposition principle of asphalt concretes, tested in the bending beam creep test at low temperatures for a long time of loading. In almost all tested asphalt concretes, deviations appeared after 500 s of loading at the temperature of -10 C. Some types of bitumen presented deviations at other temperatures – usually the harder the grade of the bitumen, the...
-
Influence of cooling rate and additives on low-temperature properties of asphalt mixtures in the TSRST
PublikacjaThe paper presents the results and analysis of low-temperature properties of asphalt mixtures according to Thermal Stress Restrained Specimen Test (TSRST) and Indirect Tensile Test methods. Different groups of bitumen were investigated: neat, SBS-modified and highly SBS-modified. Influence of cooling rates (1 C/h, 3 C/h, 5 C/h and 10 C/h) and additives (aramid fibres and crumb rubber) was identified as well. Moreover, for each...
-
Ground tire rubber thermo-mechanically devulcanized in the presence of waste engine oil as asphalt modifier
PublikacjaCross-linked elastomers network is main limitation for industrial usage of ground tire rubber (GTR) as asphalts’ and road pavements modifier. GTR was thermo-mechanically devulcanized via extrusion in the presence of waste engine oil (WEO) at temperature ranges from 150 to 280 °C. Combined impact of WEO content and extruder barrel temperature on the change of cross-linked structure of degraded GTR (DTGR) was investigated through...
-
Mechanical, durability, depolluting and electrical properties of multifunctional mortars prepared with commercial or waste carbon-based fillers
PublikacjaCarbon-based fillers from industrial wastes and commercial ones were compared to improve the properties of lime-based mixes. As commercial fillers, graphene nanoplatelets and activated carbon were used, whereas as industrial wastes a char obtained by the gasification of biomasses and a used foundry sand were chosen. Carbon-based wastes were found to be a good cost-effective alternative to commercial carbon based fillers to increase...
-
Mechanical and radiation shielding properties of concrete reinforced with boron--basalt fibers using Digital Image Correlation and X--ray micro--computed tomography
PublikacjaThe paper presents experimental investigations of the radiation shielding, mechanical and fracture properties of concrete reinforced with 5 kg/m3 of novel basalt fibers infused with boron oxide (BBF). However, further studies concerning other dosages i.e. 1 kg/m3, 10 kg/m3, 15 kg/m3 and 20 kg/m3 are currently carried out. Experiments with neutron source revealed that addition of BBF as a dispersed concrete reinforcement could improve...
-
Prediction of cast-in-place concrete strength of the extradosed bridge deck based on temperature monitoring and numerical simulations
PublikacjaThe work is devoted to the implementation of a monitoring system for high performance concrete embedded in the span of an extradosed bridge deck using a modified maturity method augmented by numerical simulations conducted by the authors’ FEM code. The paper presents all research stages of bridge construction and considers the conclusions drawn from the results of laboratory tests, field measurements, and numerical calculations....
-
Impact response of two-layered grouted aggregate fibrous concretecomposite under falling mass impact
PublikacjaTwo-layered Grouted Aggregates Fibrous Concrete Composite (TGAFCC) is a new category concrete which became popular recently and attracted the attention of researchers globally. Recent studies indicated that TGAFCC has notable improvement in mechanical properties, which has been sufficiently documented. However, the impact behaviour of TGAFCC when combined with Glass Fibre Mesh (GFM) and Textile Fibre Mesh (TFM) is still unexplored....
-
Detection of debonding in reinforced concrete beams using ultrasonic transmission tomography and hybrid ray tracing technique
PublikacjaThis paper concerns inspection of reinforced concrete elements, with particular emphasis on assessing the quality of the adhesive connection between steel and concrete. A novel theoretical model was developed to determine the paths of transmitted, refracted and reflected elastic waves as well as a creeping wave propagated along the inclusion surface. Imaging the internal structure of tested beams was based on wave propagation measurements...
-
Effect of bitumen characteristics obtained according to EN and Superpave specifications on asphalt mixture performance in low-temperature laboratory tests
PublikacjaThe paper aims to identify those characteristics of bitumen which have the greatest impact on asphalt mixture low-temperature performance. It was observed that stiffness and m-value of bitumen from BBR test were moderately related to stiffness and m-value of asphalt mixture obtained from 3 PB test. Simultaneously those rheological properties significantly impact on cryogenic stresses induced during TSRST test. The multiple regression...
-
A novel heterogeneous model of concrete for numerical modelling of ground penetrating radar
PublikacjaThe ground penetrating radar (GPR) method has increasingly been applied in the non-destructive testing of reinforced concrete structures. The most common approach to the modelling of radar waves is to consider concrete as a homogeneous material. This paper proposes a novel, heterogeneous, numerical model of concrete for exhaustive interpretation of GPR data. An algorithm for determining the substitute values of the material constants...
-
Hydrogen embrittlement of X2CrNiMoCuN25-6-3 super duplex stainless steel welded joints under cathodic protection
PublikacjaThe effect of cathodic polarization conditions on hydrogen degradation of X2CrNiMoCuN25-6-3 super duplex stainless steel welded joints, obtained using flux cored arc and submerged arc welding methods, was evaluated. Slow strain rate tensile tests of base material and welded specimens, ferrite content measurements, scanning electron microscopy observations, and statistical analysis were performed. It was found that hydrogenation...
-
The influence of combination of binding agents on fatigue properties of deep cold in-place recycled mixtures in Indirect Tensile Fatigue Test (ITFT)
PublikacjaThe publication presents fatigue properties of cold recycled mixtures for eight combinations of binding agents (cement and bituminous emulsion). Cold recycled mixtures were evaluated in Indirect Tensile Fatigue Test (ITFT) at the temperature of 20 C in controlled stress mode. As a function of horizontal stress, fatigue life is strongly influenced by combination of the binding agents. When fatigue life is analyzed as a function...
-
Finite element description of nonlinear viscoelastic behaviour of technical fabric
PublikacjaW pracy podano propozycję nieliniowego modelowania zachowania się tkaniny technicznej. Podano wyniki identyfikacji i zweryfikowano poprzez numeryczną symulację prób laboratoryjnych
-
Evaluating structural characteristics of asphalt pavements by using deflection slopes from traffic speed deflectometer
Publikacja -
Binder availability and blending efficiency of reclaimed asphalt: A state-of-the-art review
Publikacja -
Laboratory investigation of gyratory-vibratory compaction method for better simulating asphalt mixture field compaction
Publikacja -
Cementless controlled low-strength material (CLSM) based on waste glass powder and hydrated lime: Synthesis, characterization and thermodynamic simulation
Publikacja -
Evaluating the performance of inverted pavement structure using the accelerated pavement test (APT)
Publikacja -
A review on Graphene/GNPs/GO modified asphalt
Publikacja -
Dispersion, compatibility, and rheological properties of graphene-modified asphalt binders
Publikacja -
Measuring moisture damage of hot-mix asphalt (HMA) by digital imaging-assisted modified boiling test (ASTM D3625): Recent advancements and further investigation
Publikacja -
An investigation of structural responses of inverted pavements by numerical approaches considering nonlinear stress-dependent properties of unbound aggregate layer
Publikacja -
Evaluation of inverted pavement by structural condition indicators from falling weight deflectometer
Publikacja -
The dynamic thermal properties of aerogel-incorporated concretes
Publikacja -
Automatic strength assessment of the virtually modelled concrete interfaces based on shadow-light images
Publikacja -
Influence of mobilized RAP content on the effective binder quality and performance of 100% hot in-place recycled asphalt mixtures
Publikacja -
Assessment of microstructure, physical and thermal properties of bitumen modified with LDPE/GTR/elastomer ternary blends
PublikacjaLDPE/GTR/elastomer ternary blends with variable LDPE/GTR ratio and constant elastomer content were prepared via melt-compounding. Obtained LDPE/GTR/elastomer blends were applied as thermoplastic modifiers into bitumen. Microstructure, physical and thermal properties of the modified bitumen were determined. It was observed that chemical composition of LDPE/GTR/elastomer blends has significant influence on their density and rheological...
-
Mechanical properties for preliminary design of structures made from PVC coated fabric
PublikacjaIn this paper, laboratory tests necessary for the identification of non-linear elastic immediate properties of the PVC coated polyester fabric (like AF 9032) are described. The material parameters are specified on the basis of the uniaxial tensile tests in the warp and weft directions as well as on the base of the biaxial tensile tests. For the identification process techniques based on the least squares method are used. The authors...
-
Determination of causes of accelerated local corrosion of austenitic steels in water supply systems
PublikacjaThis paper concerns an inspection of a water supply system, made of AISI 304 steel, which showed signs of local corrosion at the weld. Such corrosion caused material perforation after very short periods of operation. It was revealed that steel was sensitised during the welding process. It was also proven that chromium micro-segregation occurred in the alloy leading to galvanic cell formation which initialised the process of pitting...
-
Simultaneous impedance and volumetric studies and additionally potentiodynamic polarization measurements of molasses as a carbon steel corrosion inhibitor in 1M hydrochloric acid solution
PublikacjaThe inhibition effect of molasses on the corrosion of low carbon steel in 1M hydrochloric acid solution was investigated by volumetric and electrochemical measurements. Potentiodynamic polarization and dynamic electrochemical impedance spectroscopy (DEIS) results were obtained and compared with to those, obtained with the hydrogen evolution technique. All results indicate that molasses functioned as a good inhibitor in 1M hydrochloric...
-
Influence of low-temperature physical hardening on stiffness and tensile strength of asphalt concrete and stone mastic asphalt
PublikacjaThis paper presents laboratory testing of stiffness modulus and indirect tensile strength of three asphalt concrete (AC) and three stone mastic asphalt (SMA) mixes after isothermal storage at temperature of -20oC, at different time intervals up to 16 days. The tests under repeated dynamic loading showed physical hardening of all tested mixes which was manifested by an evident increase of their stiffness moduli after isothermal...
-
Thermal stabilization and permanent deformation resistance of LWA/PCM-modified asphalt road surfaces
PublikacjaThis paper presents the results of attempts at reducing the problem of solar overheating of asphalt road pavement surfaces, resulting in weakening and accelerated destruction of the aforementioned structures. To protect pavement surfaces against periodic overheating, standard asphalt mixture AC 16 W 35/50, used for binder course, has been modified by replacing one of the aggregate fractions from the mineral mixture with lightweight...
-
Comparison of low-temperature cracks intensity on pavements with high modulus asphalt concrete and conventional asphalt concrete bases
PublikacjaHigh modulus asphalt concrete (HMAC) base courses provide very good resistance to rutting and fatigue but they can increase the risk of low-temperature cracking as compared with conventional asphalt concrete (AC). The article presents the comparison of these two road materials in terms of low-temperature cracking. The statistical method based on the ordered logistic regression model was used. The analysis was based on results of...
-
The effect of tyre rubber grinding method on the rubber-asphalt binder properties
PublikacjaRubber products, especially those used in the automotive industry, are responsible for a significant amount of waste, mainly in the form of worn tyres. One way to recycle tyres is to use them as an asphalt binder modifier. The properties of rubber-asphalt binders vary greatly depending on the morphology of the ground tyre rubber (GTR) grains and the type of tyre to be recycled (car/truck). The paper presents the results of research...
-
Time evolution of Electrochemical Impedance spectra of cathodically protected steel in artificial seawater
PublikacjaUsability of Electrochemical Impedance Spectroscopy data for better cathodic protection control was investigated. Carbon steel – S235JR2 grade specimen were exposed in artificial seawater environment. Samples were polarized and their potentials corresponded to four different cathodic protection degrees. Time evolution of Electrochemical Impedance spectra was investigated. Goodness of fit function (X2) was analysed in terms of proper...
-
Reference-free determination of debonding length in reinforced concrete beams using guided wave propagation
PublikacjaThis paper presents theoretical and experimental investigations of guided wave propagation in reinforced concrete beams, with pre-existing debonding between steel rebars and concrete blocks, for the purpose of damage detection. The primary aim of these investigations was a detailed analysis of the possible applications of wave propagation in single and multiple debonding detection in reinforced concrete structures and reference-free...
-
Electrochemical investigations on the corrosion behaviour of reinforcing steel in diatomite- and zeolite-containing concrete exposed to sulphuric acid
PublikacjaCorrosion is a major concern for most structural applications. Its detrimental effect significantly reduces the life of metallic components. This paper presents the results of an experimental investigation of corrosion in the steel reinforcement of concrete samples having three different substituents: 20% diatomite, 20% zeolite, and a reference without zeolite or diatomite. All concrete specimens were subjected to a solution of...
-
Guided ultrasonic waves for detection of debonding in bars partially embedded in grout
PublikacjaThis paper deals with theoretical, numerical and experimental investigations of guided wave propagation in multilayered cylindrical bars with pre-existing debonding. The research focuses on a complex description of the nature of the wave phenomena occurring in a debonded specimen with a special emphasis on the influence of the location of damage on the wave conversion and diffraction. Experimental non-destructive and destructive...
-
Application of Electrochemical Impedance Spectroscopy to evaluate cathodically protected coated steel in seawater
PublikacjaTwo types of organic coated carbon steel (S235JR2 grade) electrodes were exposed to artificial seawater environment. One prepared type was defect free while the other one had an intentionally introduced φ0,5 cm coating defect. Both kinds of samples were polarized during the exposure to four potentials corresponding to four different cathodic protection levels. Evolution of their EIS spectra is presented in this paper. Results obtained...