Wyszukiwarka
Wyniki wyszukiwania dla: ACRYLONITRILE BUTADIENE STYRENE
-
Effect of Thermal Shock Conditions on the Low-Cycle Fatigue Performance of 3D-Printed Materials: Acrylonitrile Butadiene Styrene, Acrylonitrile-Styrene-Acrylate, High-Impact Polystyrene, and Poly(lactic acid)
Publikacja -
A Comparative Study of Precision Surface Grinding Using Additively Fabricated Acrylonitrile–Butadiene–Styrene (ABS) Wheels with Continuous and Serrated Working Surfaces
PublikacjaNowadays, high requirements imposed by mechanical components make it necessary to develop modern production methods. Additive technologies have been dynamically developing in recent years, showing many advantages associated with the fabrication of elements with complex ge-ometries and structures. One of the areas where the potential of additive technologies is exploited is the rapid tooling sector, which is based on the rapid production...
-
Monitoring the BTEX Volatiles during 3D Printing with Acrylonitrile Butadiene Styrene (ABS) Using Electronic Nose and Proton Transfer Reaction Mass Spectrometry
PublikacjaWe describe a concept study in which the changes of concentration of benzene, toluene, ethylbenzene, and xylene (BTEX) compounds and styrene within a 3D printer enclosure during printing with different acrylonitrile butadiene styrene (ABS) filaments were monitored in real-time using a proton transfer reaction mass spectrometer and an electronic nose. The quantitative data on the concentration of the BTEX compounds, in particular...
-
Monitoring the BTEX Volatiles during 3D Printing with Acrylonitrile Butadiene Styrene (ABS) Using Electronic Nose and Proton Transfer Reaction Mass Spectrometry
Publikacja -
ID and 2D Electron Spin Resonance Imaging (ESRI) of Nitroxide Radicals in Stabilized Poly(acrylonitrile−butadiene−styrene) (ABS): UV vs Thermal Degradation
Publikacja -
Potential Alternative to Styrene–Butadiene–Styrene for Asphalt Modification Using Recycled Rubber–Plastic Blends
Publikacja -
The Taste of Waste: The Edge of Eggshell Over Calcium Carbonate in Acrylonitrile Butadiene Rubber
PublikacjaRubber technology experiences a new age by the use of biowaste or natural fillers. In this regard, taking properties of reinforcing agents from biowaste fillers remains as the challenging matter. Chicken eggshell (ES) biowaste has recently been introduced to substitute calcium carbonate (CaCO3) duo to its superior properties and low price. In this work, composites based on acrylonitrile butadiene rubber (NBR) reinforced with ES...
-
Morphology of polystyrene-block-poly(styrene-co-acrylonitrile) and polystyrene-block-poly(styrene-co-acrylonitrile-co-5-vinyltetrazole) diblock copolymers prepared by nitroxide-mediated radical polymerization and “click” chemistry
Publikacja -
Thermal decomposition kinetics of dynamically vulcanized polyamide 6-acrylonitrile butadiene rubber-halloysite nanotube nanocomposites
PublikacjaThermally stable thermoplastic elastomer nanocomposites based on polyamide 6 (PA6), acrylonitrile butadiene rubber (NBR), and halloysite nanotubes (HNTs) were dynamically vulcanized, and their nonisothermal decomposition kinetics were examined. The Friedman, Kissinger–Akahira–Sunose (KAS), Ozawa–Wall–Flynn (FWO), and modified Coats–Redfern (m‐CR) isoconversional models were used to obtain information about the kinetics of the thermal...
-
Effect of hybrid TiO2 nanoparticles with controlled morphology on rheological properties of poly(styrene-co-acrylonitrile) nanocomposites
Publikacja -
Reactive compatibilization of poly(styrene‐ran‐acrylonitrile)/poly(ethylene) blends through the acid–epoxy reaction
Publikacja -
Styrene-Butadiene Rubber/Modified Ground Tire Rubber Blends Co-Vulcanization: Effect of Accelerator Type
PublikacjaGround tire rubber was thermo-mechanically modified with using a co-rotating twin screw extruder. Modification of GTR was conducted in autothermal conditions. Styrene-butadiene rubber and modified ground tire rubber blends were prepared via two-roll milling. Obtained compounds were cured with conventional system (sulfur/vulcanization accelerator ratio was 2:1). During this research three commonly vulcanization accelerators (MBT,...
-
Fabrication of toughened plastic using styrene butadiene rubber-poly (methyl methacrylate) interpenetrating polymer networks
PublikacjaA standard set of interpenetrating polymeric networks (IPNs) has been contrived using an elastomerstyrene butadiene rubber and a thermoplastic poly (methyl methacrylate) through sequential polymerization protocol. This low-cost material can be hopefully engaged as a toughened plastic with cocontinuous morphology. Different morphological protocols including Raman imaging are effectively utilized to envisage the effect of blend ratio...
-
Chitin nanowhiskers from shrimp shell waste as green filler in acrylonitrile-butadiene rubber: Processing and performance properties
PublikacjaIn this work, chitin nanowhiskers with high crystallinity index were obtained from shrimp shells waste using acid hydrolysis method and then comprehensively characterized. Subsequently, the impact of chitin nanowhisker content on processing and performance of acrylonitrile-butadiene rubber based nanocomposites was evaluated. The results showed that the addition of chitin nanowhiskers increased tensile strength and tear strength...
-
Cellulosic bionanocomposites based on acrylonitrile butadiene rubber and Cuscuta reflexa: adjusting structure-properties balance for higher performance
PublikacjaDesign and manufacture of cellulosic nanocomposites with acceptable performance is in the period of a transition from fantasy to reality. Typically, cellulosic nanofillers reveal poor compatibility with polymer matrices. Thus, adjusting the balance between structure and properties of cellulosic bionanocomposites by careful selection of parent ingredients is the first priority. Herein, we incorporated Cuscuta reflexa derived cellulose...
-
Enhanced interfacial and mechanical performance of styrene-butadiene rubber/silica composites compatibilized by soybean oil derived silanized plasticization
PublikacjaSilanized plasticizer (SP) was chemically derived and synthesized from soybean oil (SBO) co-vulcanized with bis-(3-(triethoxysilyl)-propyl) tetrasulfide (TESPT) by using the sulfur-accelerated curing system. SP extended styrene-butadiene rubber (SBR)/silica composites have been studied for their improved filler dispersion through coupling interaction at the SBR/silica interface. The effect of SP on cross-link density, thermal,...
-
Super tough interpenetrating polymeric network of styrene butadiene rubber‐poly (methyl methacrylate) incorporated with general purpose carbon black ( N660 )
PublikacjaA classic set of polymeric interpenetrating polymeric network (IPN) microcomposites has been fabricated using an elastomer—styrene butadiene rubber [SBR], a thermoplastic poly(methyl methacrylate)-PMMA and with carbon black (CB)-N660 as a filler and reinforcing agent. This synthesized IPN composite can be promisingly employed as a toughened plastic and vibrational damper in a wide service range with excellent thermal stability,...
-
The emissions of monoaromatic hydrocarbons from small polymeric toys placed in chocolate food products
PublikacjaThe article presents findings on the emissions of selected monoaromatic hydrocarbons from children's toys placed in chocolate food products. The emission test system involved the application of a new type of microscale stationary emission chamber, μ-CTE™ 250. In order to determine the type of the applied polymer in the manufacture of the tested toys, Fourier transform infrared spectroscopy and thermogravimetric analysis coupled...
-
Emission Profiles of Volatiles during 3D Printing with ABS, ASA, Nylon, and PETG Polymer Filaments
PublikacjaIn this short communication we characterize the emission of volatile organic compounds (VOCs) from fused filament fabrication (FFF) 3D printing using four polymer materials, namely polyethylene terephthalate glycol-modified (PETG), acrylonitrile styrene acrylate (ASA), Nylon, and acrylonitrile butadiene styrene (ABS). Detailed emission profiles are obtained during thermal degradation of the polymers as a function of temperature...
-
Modeling and Strength Calculations of Parts Made Using 3D Printing Technology and Mounted in a Custom-Made Lower Limb Exoskeleton
PublikacjaThis study is focused on the application of 3D-printed elements and conventional elements to create a prototype of a custom-made exoskeleton for lower limb rehabilitation. The 3D-printed elements were produced by using Fused Deposition Modeling technology and acrylonitrile butadiene styrene (ABS) material. The scope of this work involved the design and construction of an exoskeleton, experimental testing of the ABS material and...
-
Quality Evaluation of Small Features Fabricated by Fused Filament Fabrication Method
PublikacjaThe purpose of this research was to evaluate the quality of small features fabricated by the fused filament fabrication (FFF) method. The samples containing circular and square cross-sections through holes with different dimensions, lengths, and orientation angles were printed from ABS (acrylonitrile butadiene styrene) filament. The adopted optical inspection method allowed us to conduct observations of individual features and...
-
Static and Dynamic Mechanical Properties of 3D Printed ABS as a Function of Raster Angle
PublikacjaDue to the rapid growth of 3D printing popularity, including fused deposition modeling (FDM), as one of the most common technologies, the proper understanding of the process and influence of its parameters on resulting products is crucial for its development. One of the most crucial parameters of FDM printing is the raster angle and mutual arrangement of the following filament layers. Presented research work aims to evaluate different...
-
Emission and properties of airborne wear particles from train brake friction materials based on novolac phenolic resins and butadiene rubbers
PublikacjaThe emission of airborne particulate matter from a train brake depends on the formulation of its friction material. This study investigates the emission and properties of wear particles from train brake friction materials based on straight or resorcinol-modified novolac phenolic resin and nitrile or styrene butadiene rubber used as binding ingredients. The wear particles are generated by a pin-on-disc tribomachine inside an aerodynamic...
-
Determination of modifier contents in polymer-modified bitumens and in samples collected from the roads using high performance gel permeation/size exclusion chromatography
PublikacjaThis paper describes application of high performance gel permeation/size exclusion chromatography (HP-GPC/SEC) for the determination of content of polymer modifiers in modified road bitumens. The obtained results were compared with the measurements based on the procedure recommended by the American Association of State Highway and Transportation Officials, which employs Fourier transform mid-infrared spectroscopy (mid-IR FTIR)....
-
Influence of novolac phenolic resins and butadiene rubbers on airborne wear particles emission from train brake friction materials against steel brake discs with roughness of Ra2.5
Dane BadawczeThree train brake materials based on straight or resorcinol-modified novolac phenolic resin and nitrile or styrene-butadiene rubber were tested during pin-on-disc tribological tests. Each material was tested and retested at 9 different friction regimes with various contact pressure values (0.33, 0.66 and 1 MPa) and various sliding velocity values (0.6,...
-
Ground Tire Rubber Modified by Elastomers via Low-Temperature Extrusion Process: Physico-Mechanical Properties and Volatile Organic Emission Assessment
PublikacjaIn this paper, low-temperature extrusion of ground tire rubber was performed as a proecological waste tires recycling method. During this process, ground tire rubber was modified with constant content of dicumyl peroxide and a variable amount of elastomer (in the range: 2.5–15 phr). During the studies, three types of elastomers were used: styrene-butadiene rubber, styreneethylene/butylene-styrene grafted with maleic anhydride and...
-
Reclaimed rubber in-situ grafted with soybean oil as a novel green reactive plasticizer in SBR/silica compounds
PublikacjaPolymer recycling and biodegradable polymeric materials are two major routes towards the sustainable development of polymer materials which contributes to the management of waste. In this regard, an eco-friendly approach is presented wherein high reclaiming degree of ground tire rubber (GTR) was achieved by low-temperature oxidation under swollen action of soybean oil. In-situ reclaimed GTR with soybean oil was cured into reactive...
-
Efficiency of thermomechanical reclaiming of ground tire rubber conducted in counter-rotating and co-rotating twin screw extruder
PublikacjaIn this article the results of research on a continuous thermomechanical reclaiming process of ground tire rubber (GTR) conducted in a twin screw extruder are presented. The effects of the rotation direction (co-rotating/counter-rotating), design of co-rotating plasticizing units and the rotational speed of the screws on the extruder working parameters, sol fraction and the degree of reclaiming in the obtained products were described....
-
INFLUENCE OF SOLID PARTICLE CONTAMINATION ON THE WEAR PROCESS IN WATER LUBRICATED MARINE STRUT BEARINGS WITH NBR AND PTFE BUSHES
PublikacjaThis paper reports on a study of the influence of solid particle contamination on the wear process in water-lubricated slide bearings (steel-acrylonitrile-butadiene rubber (NBR) and steel- polytetrafluoroethylene (PTFE)). To compare the wear of the shaft journal and bushes (NBR and PTFE) when lubricated with fresh water and contaminated water, an experiment was carried out to identify key factors that influence the state of wear...
-
Low-Temperature Requirements for Bitumen in Central East European Road Construction
PublikacjaThe paper presents the proposition of special assessment of lowtemperature requirements for bitumens in the region of Central and Eastern Europe where there is a moderate transitional area from sea to the continental type of climate. The results of the research program conducted on the road neat bitumens, Styrene-Butadiene-Styrene polymer and polymer-rubber modified bitumen, and multigrade bitumen types were presented and discussed....
-
Processing, Mechanical and Morphological Properties of GTR Modified by SBS Copolymers
PublikacjaIn this work, ground tire rubber (GTR) was thermo-mechanically treated in the presence of styrene-butadiene-styrene (SBS) copolymers. During preliminary investigation, the effects of different SBS copolymer grades, the variable content of SBS copolymer on the Mooney viscosity, and the thermal and mechanical properties of modified GTR were determined. Subsequently, GTR modified by SBS copolymer and cross-linking agents (sulfur-based...
-
Morphology and mechanical properties of polyamide/clay nanocomposites toughened with NBR/NBR-g-GMA: A comparative study
PublikacjaThis work highlights the importance of nanoclay dispersion state in the nanocomposites containing polyamide 6 (PA6), nanoclay and elastomers as well as clay localization at the interface of thermoplastic/elastomer. Morphology and mechanical properties of a series of nanocomposites containing acrylonitrile butadiene rubber (NBR), glycidyl methacrylate-grafted NBR (NBR-g-GMA), and combined NBR/NBR-g-GMA were compared and discussed...
-
Application of Tensile Creep Test and Viscoelastic Method to the Analysis of Thermal Stresses at Low Temperatures
PublikacjaThe paper presents the viscoelastic method of thermal stresses calculation with utilization of results from tensile creep test (TCT) at a temperature range from −20 to +20 °C (in the case of asphalt concrete with styrene-butadiene-styrene (SBS) polymer-modified bitumen from −30 to +20 °C). Two types of neat road bitumen 35/50 and 50/70 and polymer SBS-modified bitumen 45/80–55 were tested for tensile creep properties at low temperatures....
-
Interfacially modified LDPE/GTR composites with non-polar elastomers: From microstructure to macro-behavior
PublikacjaThis paper provides some new insights into the mechanism of interaction and modifications in thermoplastic composites based on low density polyethylene (LDPE), ground tire rubber (GTR) and non-polar elastomer. The composites were prepared using a co-rotating twin-screw extruder at variable LDPE/GTR ratio and constant elastomer content. Two types of commercial elastomer were applied: styrene-butadiene-styrene (SBS) block copolymers (Kraton®)...
-
Towards understanding the role of peroxide initiators on compatibilization efficiency of thermoplastic elastomers highly filled with reclaimed GTR
PublikacjaThermoplastic elastomers based on recycled high density polyethylene (rHDPE) and styrene-butadiene-styrene (SBS) block copolymer were highly filled with reclaimed ground tire rubber (RR). The impact of various organic peroxides (dicumyl peroxide (DCP), benzoyl peroxide (BP) and di-tert-butyl peroxide (DB)), applied as free-radical initiators, on the processing, structure and performance properties of rHDPE/SBS/RR blends was investigated....
-
To what extent can hyperelastic models make sense the effect of clay surface treatment on the mechanical properties of elastomeric nanocomposites?
PublikacjaThe poor knowledge about nonlinear mechanical behavior of elastomer nanocomposites arises from the incomplete information on the interface. Application of hyperelastic models provides more insights into the nature and the situation of interaction between the elastomeric matrix and nanofillers. The current work seeks to address the effect of interphase strength on tensile properties of the elastomer nanocomposites under large deformations....
-
Thermo-mechanical reclaiming of ground tire rubber via extrusion at low temperature: Efficiency and limits
PublikacjaThermomechanical reclaiming of ground tire rubber (GTR) was performed at different temperatures (60, 120, and 180°C) using a co-rotating twin-screw extruder. Obtained samples were used in styrene-butadiene rubber (SBR) blends. As reference samples, SBR compounds containing untreated GTR were used. Curing characteristics, static and dynamic mechanical properties, and morphology of the obtained blends were determined. The results...
-
Investigating the combined impact of plasticizer and shear force on the efficiency of low temperature reclaiming of ground tire rubber (GTR)
PublikacjaIn the present work, ground tire rubber (GTR) was mechano-chemically reclaimed at ambient temperature using two-roll mills. Road bitumen and styrene-butadiene-styrene (SBS)-modified bitumen at variable content (in range: 2.5–20 phr) were applied as reactive plasticizers to enhance reclaiming of GTR. For better understanding the plasticizing effect of bitumen on the quality of obtained reclaimed rubber, mechano-chemically reclaimed...
-
Vegetable derived-oil facilitating carbon black migration from waste tire rubbers and its reinforcement effect
PublikacjaThree dimensional chemically cross-linked polymer networks present a great challenge for recycling and reutilization of waste tire rubber. In this work, the covalently cross-linked networks of ground tire rubber (GTR) were degraded heterogeneously under 150 °C due to the synergistic effects of the soybean oil and controlled oxidation. The degradation mechanism was discussed using Horikx theory and Fourier transformation infrared...
-
Processing, Performance Properties, and Storage Stability of Ground Tire Rubber Modified by Dicumyl Peroxide and Ethylene-Vinyl Acetate Copolymers
PublikacjaIn this paper, ground tire rubber was modified with dicumyl peroxide and a variable content (in the range of 0–15 phr) of ethylene-vinyl acetate copolymers characterized by different vinyl acetate contents (in the range of 18–39 wt.%). Modification of ground tire rubber was performed via an auto-thermal extrusion process in which heat was generated during internal shearing of the material inside the extruder barrel. The processing,...
-
Wastes from Agricultural Silage Film Recycling Line as a Potential Polymer Materials
PublikacjaThe recycling of plastics is currently one of the most significant industrial challenges. Due to the enormous amounts of plastic wastes generated by various industry branches, it is essential to look for potential methods for their utilization. In the presented work, we investigated the recycling potential of wastes originated from the agricultural films recycling line. Their structure and properties were analyzed, and they were...
-
Investigating the combined effects of devulcanization level and carbon black grade on the SBR/GTR composites
PublikacjaCarbon black migration between ground tire rubber (GTR) and rubber matrix is essential in developing high-performance rubber/GTR composites. In this work, carbon black N220 (surface area: 107.1 m2/g, particle size: 20–25 nm) andN660 (surface area: 33.1 m2/g, particle size: 49–60 nm) were used as the reinforcement fillers for styrene-butadiene rubber(SBR) blended with reclaimed GTR. The combined effects of GTR devulcanization level...
-
Cross-Linking, Morphology, and Physico-Mechanical Properties of GTR/SBS Blends: Dicumyl Peroxide vs. Sulfur System
PublikacjaIn this work, ground tire rubber and styrene–butadiene block copolymer (GTR/SBS) blends at the ratio of 50/50 wt%, with the application of four different SBS copolymer grades (linear and radial) and two types of cross-linking agent (a sulfur-based system and dicumyl peroxide), were prepared by melt compounding. The rheological and cross-linking behavior, physico-mechanical parameters (i.e., tensile properties, abrasion resistance,...
-
Curing characteristics, mechanical properties and morphology of butyl rubber filled with ground tire rubber (GTR)
PublikacjaThe results on testing application of ground tire rubber (GTR), as potential filler for butyl rubber, are pre- sented. The GTR content variation, within the range of 10–90 phr, was studied with respect to the vulcanization process, static mechanical properties (tensile strength, elongation-at-break, hardness and resilience), dynamic mechanical properties and the morphology of the obtained vulcanizates. Butyl rubber was characterized...
-
Evaluation and rationale of the performance of several elastomeric composites incorporating devulcanized EPDM
Publikacjathylene Propylene Diene rubber (EPDM), is present in many applications. However, its crosslinked structure makes difficult its recycling. The use of devulcanized EPDM, (dEPDM) as a component of elastomeric composites, is a real possibility to reuse EPDM scraps. In this study, three matrices (natural rubber (NR), styrene butadiene rubber (SBR) and EPDM rubber) have been tested including devulcanized EPDM as a recycled component....
-
Electron scattering from 2-methyl–1,3-butadiene,C5H8, molecules: Role of methylation
PublikacjaWe report cross-section results from experimental and theoretical investigations into electron collisions with the 2-methyl–1,3-butadiene [C5H8] molecule. The current results are compared with our previous results for the 1,3-butadiene [C4H6] molecule, a structural homologue of 2-methyl–1,3-butadiene, to investigate how the methylation (the substitution of hydrogen atom by a methyl group) affects the shape and/or magnitude of the...
-
Scattering of electrons by a 1,2-butadiene (C4H6) molecule: measurements and calculations
PublikacjaWe present the results of experimental and theoretical study on electron collisions with a 1,2-butadiene (H2C=C=CHCH3) molecule. Absolute grand-total cross sections (TCSs) were measured using a linear electron-transmission method for collision energies in the 0.5–300 eV range. Two distinct features in the TCS energy curve were detected: a narrow peak located at 2.3 eV and a broad enhancement centered around 9 eV. We attributed...
-
Copolymerization of Styrene and Pentadecylphenylmethacrylate (PDPMA): Synthesis, Characterization, Thermomechanical and Adhesion Properties
PublikacjaThe copolymerization of styrene (St) with a bioderived monomer, pentadecylphenylmethacrylate (PDPMA), via atom transfer radical polymerization (ATRP) was studied in this work.The copolymerization reactivity ratio was calculated using the composition data obtained from1HNMR spectroscopy, applying Kelen-Tudos and Finemann-Ross methods. The reactivity ratio of styrene (r1=0.93) and PDPMA (r2=0.05) suggested random copolymerization...
-
Indole-Acrylonitrile Derivatives as Potential Antitumor and Antimicrobial Agents—Synthesis, In Vitro and In Silico Studies
PublikacjaA series of 2-(1H-indol-2-yl)-3-acrylonitrile derivatives, 2a–x, 3, 4a–b, 5a–d, 6a–b, and 7, were synthesized as potential antitumor and antimicrobial agents. The structures of the prepared compounds were evaluated based on elemental analysis, IR, 1H- and 13NMR, as well as MS spectra. X-ray crystal analysis of the representative 2-(1H-indol-2-yl)-3-acrylonitrile 2l showed that the acrylonitrile double bond was Z-configured. All...
-
Styrene epoxidation over heterogeneous manganese(III) complexes
PublikacjaThe manganes(III) complex functionalised with 2,3-dihydropyridazine has been encapsulated in the supercages of the NaY zeolite using two different procedures, flexible ligand and in situ complex. The parent zeolite and the encapsulated manganese(III) complexes were screened as catalysts for styrene oxidation by using t-BOOH as the oxygen source in acetonitrile. Under the optimized conditions, the catalysts exhibited moderate activity...