Wyszukiwarka
Wyniki wyszukiwania dla: EXPERIMENTAL INVESTIGATION
-
Experimental investigation of a two-phase thermosiphon.
PublikacjaPrzedstawiono wyniki badań dwufazowego, termosyfonowego wymiennika ciepła. W szczególności uwzględniono wpływ podziałki rur oraz wartość ciśnienia w płaszczu na gęstość przenoszonego strumienia ciepła.
-
Modeling and experimental investigation of the small UPQC systems
Publikacja -
Modeling and experimental investigation of the small UPQC systems
PublikacjaIn this paper the basis of analytical modelling of the UPQC arrangements (Unified Power Quality Conditioner) in d-q rotating coordinates, as well as select results of investigations conducted on the simplified small power laboratory model were talked over. In short form power balance as well as fundamental dependences and analytic model with regard of decoupling circuits were investigated. Applied method for DC link capacity selection...
-
Experimental investigation of joint with positive eccentricity in CFS truss
PublikacjaDue to technological restrictions, in the case of trusses made of CFS open cross-sections, positive eccentricities in the truss joints have become very frequent. Therefore studies concerning the load-bearing capacity of truss joints with positive eccentricity were undertaken. It was assumed that the resistance of cold-formed steel (CFS) open cross-section truss joints located on compression chords and with positive eccentricity...
-
An experimental investigation of the influence of plasticity on creep degradation rate
Publikacja -
Theoretical and experimental investigation of Optical Coherent Tomography topologies
PublikacjaW artykule przedstawiono teoretyczną i eksperymentalną analizę konfiguracji interferometrów w układach koherentnego tomografu optycznego. Zaprezentowano zrealizowany układ, którego specjalnie zaprojektowana konfiguracja pozawala na analizę zmian polaryzacji sygnału pomiarowego.
-
An experimental investigation of the influence of plasticity on creep degradation rate
Publikacja -
Experimental investigation into surface texture effect on journal bearings performance
PublikacjaThe aim of this study was to analyse the performance of journal bearings with specially created dimples on the sliding surface and operating under various conditions. The texture was created on the bearing surface that co-acted with the smooth journal; moreover, the variation of the textured surface of the journal mating with the smooth bearing was tested, and the results were compared to those obtained with the standard smooth...
-
Experimental Investigation of Prototype Water-Lubricated Compliant Foil Bearings
PublikacjaPraca zawiera wyniki badań doświadczalnych prototypowego łożyska foliowego smarowanego wodą. Łożyska tego typu mogą mieć zastosowanie w węzłach, od których wymaga się ekologicznego środka smarowego, np. pompy wodne czy turbiny wodne. W opracowaniu zademonstrowano wyniki badań trzech prototypowych poprzecznych łożysk foliowych. Opisano napotkane problemy badań oraz wprowadzonych do konstrukcji łożyska zmian, których celem była poprawa...
-
Selected problems of experimental investigation of dynamically loaded journal bearings
PublikacjaIn the paper some problems concerning relations between external bearing loadings and critical lining stresses are described for test stand with rotating load vector. According to the standard ISO 7905/1 this type of test stand, for dynamically loaded slide bearing, is recommended as a basic research unit for material testing in a complete bearing unit. The lining stress calculation results occurred being dependent on applied calculation...
-
Experimental investigation of Organic Rankine Cycles for domestic micro CHP
PublikacjaW artykule przedstawiono wyniki badań eksperymentalnych obiegu ORC wyposażonego w ekspander typu scroll (I etap badań) oraz ekspander utworzony na bazie turbinki pneumatycznej (II etap badań). Raportowane badania przeprowadzono na laboratoryjnym stanowisku realizującym obieg ''domowej'' mikrosiłowni parowej.
-
Experimental investigation of domestic gas boiler fitted with ORC module
PublikacjaIn the paper the prototype of innovative domestic cogenerative ORC system, consisting of a conventional gas boiler and a small size axial vapour microturbines (in-house designed for ORC and the commercially available for Rankine cycle (RC)), evaporator and condenser were scrutinised. In the course of study the fluid working temperatures, rates of heat, electricity generation and efficiency of the whole system were obtained. The...
-
Nucleate pool boiling modelling and experimental investigation : chapter 7
PublikacjaOmówiono wpływ powłoki porowatej nanoszonej na całą powierzchnię rurki lub jej fragment na osiągany współczynnik przejmowania ciepła, krytyczne gęstości strumienia ciepła, a także obwodowy rozkład temperatury przy wrzeniu pęcherzykowym na zewnętrznej powierzchni poziomej rurki.Przedstawiono wyniki badań częstotliwości odrywania się pęcherzyków oraz pól prędkości wokół wzrastającyh i unoszących się pęcherzyków przy wrzeniu z pojedynczych...
-
Response of a steel tank during earthquakes and mining tremors - experimental investigation
PublikacjaCylindrical steel tanks are very popular shell structures used to store the products of chemical and petroleum industries. Any failure might have disastrous consequences, therefore their safety and reliability is essential. Earthquakes are the most dangerous and also the most unpredictable dynamic loads acting on such structures. On the other hand, mining tremors are usually considered to be less severe due to lower acceleration...
-
An Experimental Investigation of Pressure Wave Celerity During the Transient Slurry Flow
PublikacjaTransportation of slurries in pressure pipelines is an example of a complex flow due to specific parameters of transported medium. For practitioners, the economy of designing and maintenance is usually the most important factor. For this reason, most of hydrotransport installations are fairly simple; however, they become more vulnerable to negative effects of the transient flow which can occur in pressure pipelines. As the consequence,...
-
Experimental investigation of two-phase thermosyphon heat exchanger charged with acetone
PublikacjaThis paper presents thermal characteristics of prototype of a two-phase thermosyphon heat exchanger (TPTHEx) charged with acetone as a working fluid. The TPTHEx consists of two horizontal cylindrical vessels connected by two risers and a downcomer. Tube bundles placed in the lower and upper cylinders work as an evaporator and a condenser, respectively. The tested TPTHEx operates in a vacuum. Therefore, the working liquid is boiled...
-
Experimental Investigation of Elastic Waves Propagation in 1D and 2D Structures with Faults.
PublikacjaW pracy omówiono wyniki pomiarów fal sprężystych w prętach, belkach i płytach z uszkodzeniami.
-
Experimental investigation of the PEM fuel cells performance for automotive and stationary applications
PublikacjaThe aim of the study was to provide dynamic characteristics of the PEM fuel cell system consisted of Nexa modules, provide steady-state characteristics of the for different values of air excess ratio and steady-state characteristics for different stack temperatures and given load.
-
Numerical and experimental investigation of rotational stiffness of zed-purlins connection with sandwich panels
PublikacjaA rotational resistant stiffness of the zed-purlins connection with sandwich panels is investigated. A simple finite element method model of the connection is proposed. The numerical analysis of the model performed by ABAQUS software, in physically linear and geometrically nonlinear ranges, leads to the rotational resistant stiffness sought. The numerical solution obtained is verified experimentally. Two variants of distribution...
-
Numerical and experimental investigation of thermal convection near electric devices with vertical channels
PublikacjaThis paper presents the results of numerical and experimental investigation of thermal convection near heat emitting surfaces of an electric device. For the intensification of thermal convection, special vertical channels were formed near the heat emitting surfaces of the device. An experimental test has proved that there is an optimal length of the channels – thermal convection is the most intensive then. Air velocity vectors...
-
EXPERIMENTAL INVESTIGATION OF FREE CONVECTION OF GLYCOL-Al2O3 NANOFLUID FROM HORIZONTAL TUBE
PublikacjaNanofluids came to be seen as a new generation of coolants, both in single- and two phase systems. Furthermore, nanofluids or nanocomposites may be used as a media in a thermal energy storage (TES) in such systems as sensible heat storage (SHS) and phase change materials (PCM). In the SHS systems the dominating mechanism of the heat transfer is natural convection. However, in the literature only a few investigations of free convection...
-
Experimental investigation of free convection of glycol-Al2O3 nanofluid from horizontal tube
PublikacjaNanofluids came to be seen as a new generation of coolants, both in single- and two phase systems. Furthermore, nanofluids or nanocomposites may be used as a media in a thermal energy storage (TES) in such systems as sensible heat storage (SHS) and phase change materials (PCM). In the SHS systems the dominating mechanism of the heat transfer is natural convection. However, in the literature only a few investigations of free convection...
-
Experimental Investigation of Free Convection Heat Transfer from Horizontal Cylinder to Nanofluids
PublikacjaThe results of free convection heat transfer investigation from a horizontal, uniformly heated tube immersed in a nanofluid are presented. Experiments were performed with five base fluids, i.e., ethylene glycol (EG), distilled water (W) and the mixtures of EG and water with the ratios of 60/40, 50/50, 40/60 by volume, so the Rayleigh (Ra) number range was 3 104 Ra 1.3 106 and the Prandtl (Pr) number varied from 4.4 to 176....
-
Experimental Investigation of high frequency 3L-NPC qZS inverter for photovoltaic application
Publikacja -
Experimental investigation of utilizing waste flue gas desulfurized gypsum as backfill materials
Publikacja -
Experimental investigation of forced convection of water/EGAl2O3 nanofluids inside horizontal tube
PublikacjaIn this paper, forced convection of water/EG-Al2O3 nanofluids inside horizontal stainless steel tube is studied experimentally. As base fluid served water/EG mixture of two ratios (60:50 and 50:50). Nanoparticle mass concentrations was 0.1% or and 1%. Transition and turbulent flow regimes were tested. Average heat transfer coefficient and pressure drop values were determined for nanofluids and compared to base fluids. Deterioration...
-
Experimental Investigation of the ORC System Elements of a Home Cogenerative Micro Power Plant
PublikacjaW pracy przedstawiono wyniki badań obiegu ORC z prototypową pompą czerpakową czynnika roboczego HFE 7100 i elektrycznym przepływowym podgrzewaczem oleju termalnego w układzie ORC bez regeneracji. Z analizy wyników badań wynika, że w obiegu ORC bez regeneracji z zaworem rozprężnym (symulującym pracę mikroturbiny) osiągnięto przegrzanie par czynnika niskowrzącego HFE 7100. Uzyskano powtarzalność wyników badań wykonanych serii pomiarowych...
-
Experimental Investigation of an Intensified Heat Transfer Adsorption Bed (IHTAB) Reactor Prototype
Publikacja -
Experimental investigation of forced convection of water-Al2O3 nanofluids inside horizontal tubes,
PublikacjaIn this paper, forced convection of water–Al2O3 nanofluids inside horizontal copper tube is studied experimentally. Experiments were conducted for three, i.e. 0.1%, 1% and 5% nanoparticle mass concentrations under transition and turbulent flow regimes. Average heat transfer coefficients and pressure drop values were determined and compared to distilled water. Enhancement of heat transfer for lower nanoparticle concentration and...
-
Experimental investigation and process parameter optimization of sheet metal bending by line heating method
PublikacjaThe present study is concerned with the experimental investigation of sheet metal deforming by line heating method that incorporates the combined effect of traverse speed of the torch, thickness of the sheet metal, and the number of passes of the torch. For the numerical analysis of metal bending by line heating, the
-
Experimental Investigation of the Performance of an Innovative Implantable Left Ventricular Assist Device—Proof of Concept
PublikacjaThis paper presents the results of experimental performance of an innovative left ventricular assist device working on a specially designed test stand. The introduced invention is mainly applied for supporting the heart in patients with end-stage heart failure accompanied by mitral valve regurgitation and pulmonary hypertension. Moreover, the developed device has the form of a flexible balloon forming an intracardiac inert gas-filled...
-
Dataset Related Experimental Investigation of Chess Position Evaluation Using a Deep Neural Network
PublikacjaThe idea of training Articial Neural Networks to evaluate chess positions has been widely explored in the last ten years. In this paper we investigated dataset impact on chess position evaluation. We created two datasets with over 1.6 million unique chess positions each. In one of those we also included randomly generated positions resulting from consideration of potentially unpredictable chess moves. Each position was evaluated...
-
Experimental investigation of the flow pattern and wall pressure distribution in a silo with double-cone insert
PublikacjaArtykuł opisuje przeprowadzone badania przepływów silosowych i naporu materiałów sypkich podczas napełniania i opróżniania silosu o średnicy 2.5 m wyposażonego we wkładkę "podwójny stożek". Badania przeprowadzane były w Instytucie Badawczym Tel-Tek w Norwegii. Materiałem użytym był suchy piasek. Napór na ścianę mierzony był bezpośrednio za pomocą 10 czujników wbudowanych w ścianę. Badania eksperymentalne pokazały duży wpływ wkładki...
-
Experimental investigation of dryout of SES36, R134a, R123 and ethanol in vertical small diameter tubes
PublikacjaW publikacji przedstawiono wyniki badań eksperymentalnych kryzysu wrzenia typu dryout podczas wrzenia w przepływie czterech czynników (SES36, R134a, R123, alkohol etylowy) w kanałach o średnicy wewnętrznej 1.15 mm i 2.3 mm. Badania przeprowadzono w szerokim zakresie zmian stopnia suchości pary (0.65-1), gęstości strumienia masy (40-900 kg/(m2s)) i gęstości strumienia ciepła (20-220 kW/m2). W badaniach wykorzystano technikę termowizyjną...
-
Experimental investigation of domestic micro-CHP based on the gas boiler fitted with ORC module
PublikacjaThe results of investigations conducted on the prototype of vapour driven micro-CHP unit integrated with a gas boiler are presented. The system enables cogeneration of heat and electric energy to cover the energy demand of household. The idea of such system is to produce electricity for own demand or for selling it to the electric grid – in such situation the system user will became the prosumer. A typical commercial gas boiler,...
-
Experimental investigation of Steel–Concrete–Polymer composite barrier for the ship internal tank construction
PublikacjaTransportation of dangerous cargo by ships demands ensuring an appropriate protection level in case of an accident. Two of the most dangerous accident types resulting in an oil spill are grounding and ship to ship collision. The article presents results of research on a new composite construction for a ship hull that increases structural safety during collision. The concept of semi-elastic Steel–Concrete–Polymer structure is presented....
-
Experimental investigation on heat pipes supported by soy wax and lauric acid for electronics cooling
PublikacjaThis paper presents an experimental study of heat pipes for electronics cooling that were supported by energy storage materials (i.e. phase change materials - PCMs) coated at the adiabatic section. The PCMs utilized included two materials, namely lauric acid and soy wax, the latter being considered as a more cost-effective alternative. The study focused on three different powers: 20 W, 25 W, and 30 W. Both heating, cooling, and...
-
Experimental investigation of the weight averaging of pulse frequency modulated sensor output signal
Dane BadawczeThe research aims to practically verify the results of theoretical analysis and simulations of the efficiency of weight averaging of pulse frequency modulated signal. For this purpose, a suitable test stand was built, and the control software in the LabVIEW environment was prepared. Then, a series of experiments were carried out to process and analyze...
-
Effect of asymmetric fluid flow distribution on flow boiling in a microchannel heat sink – An experimental investigation
PublikacjaFlow boiling in microchannels is emerging as an exclusive cooling solution for miniaturized high-power electronic devices alongside having other high heat flux applications. Size miniaturization at microscale strangely increases heat transfer performance as well as flow boiling instabilities. Many flow boiling instabilities are interrelated and result from imperfect hydrodynamic conditions. One of such problems is flow maldistribution among...
-
Experimental Investigation of Adhesion Failure between Waterproof Coatings and Terrace Tiles under Usage Loads
Publikacja -
Numerical and experimental investigation of guided ultrasonic wave propagation in non-uniform plates with structural phase variations
PublikacjaThe article presents the results of numerical and experimental investigations of guided wave propagation in aluminum plates with variable thickness. The shapes of plate surfaces have been specially designed and manufactured using a CNC milling machine. The shapes of the plates were defined by sinusoidal functions varying in phase shift, which forced the changes in thickness variability alongside the propagation path. The main aim...
-
Theoretical and experimental investigation of low-noise optoelectronic system configurations for low-coherent optical signal detection
PublikacjaW artykule przedstawiono wyniki teoretycznej i eksperymentalnej analizy konfiguracji niskokoherencyjnego układu detekcji sygnałów optycznych. Zaprezentowano zaprojektowany układ detekcji optycznych sygnałów niskokoherencyjnych, który pozwala na pracę w konfiguracji zrównoważonej i niezrównoważonej, co umożliwia porównanie parametrów obu konfiguracji.
-
Experimental investigation on the effect of dry and multi-jet cryogenic cooling on the machinability and hole accuracy of CFRP composites
Publikacja -
Experimental investigation on straight and u-bend double tube heat exchanger with active and passive enhancement methods
PublikacjaAuthors in this work want to demonstrate the possibility to increase the heat transfer efficiency by using simple wire coil inserts to create turbulent flow in the boundary layer as well as air blowing into the annulus of the pipe. In the study, Wilson plot approach was applied in order to estimate heat transfer coefficients for all heat exchanger (HX) configurations. The study focuses on experimental values of heat transfer coefficient...
-
Experimental investigation of heat transfer enhancement in straight and U-bend double-pipe heat exchanger with wire insert
PublikacjaIn this paper, the possibility of heat transfer enhancement in the U-bend exchanger was presented. Experimental research has been carried out for four individual heat exchanger constructions i.e. plain tube in tube, turbulized tube in tube, plain U-bend and U-bend with turbulator. Also, heat transfer experiments for various boundary conditions were performed to obtain reference values. In case of U-bend exchanger with and without...
-
Modelling and experimental investigation of the phenomenon of brekdown of the liquid layer formed by an impinging two-phase air-water jet
PublikacjaW pracy przedstawiono analizę teoretyczną i badania eksperymentalne badania zjawiska rozrywania warstwy cieczy powstałej z uderzającej strugi
-
Modeling and experimental investigation of the hydraulic jump in liquid film formed by an impinging two-phase air-water jet
PublikacjaPrzedstawiono model analityczny układu hydraulicznego powstałego na skutek uderzenia strugi dwufazowej wody i powietrza. Obliczenia porównano z badaniami eksperymentalnymi przeprowadzonymi na własnym stanowisku badawczym. Uzyskano zadowalającą zgodność.
-
Experimental investigation of M-shape heat transfer coefficient distribution of R123 flow boiling in small-diameter tubes
PublikacjaW publikacji przedstawiono wyniki badań wrzenia czynnika R123 w srebrnych rurkach o małych średnicach (średnice wewnętrzne wynosiły odpowiednio 1.15 mm i 2.3 mm). Badania przeprowadzono w szerokim zakresie stopnia suchości pary (0.01-0.9), gęstości strumienia masy (650-3000 kg/(m2s)) oraz gęstości strumienia ciepła (40-80 kW/m2). W badaniach wykazano, że istnieją dwa lokalne maksima współczynnika przejmowania ciepła w jego profilu...
-
Experimental investigation and optimization of compression moulding parameters for MWCNT/glass/kevlar/epoxy composites on mechanical and tribological properties
Publikacja -
Experimental investigation of thermal energy storage in shell-and-multi-tube unit with nano-enhanced phase change material
PublikacjaThis paper deals with thermal energy storage with use of nanoparticle enhanced phase change material in shell-and-multitube unit. The experiments are conducted under atmospheric pressure. Paraffin wax and two different fatty acids are used as base phase change material. Graphite and multi-walled carbon nanotubes serve as nanoparticles. Graphite nanoparticles are tested at the concentrations of 0.1%, 1% and 5% by weight, while multi-walled...