Filtry
wszystkich: 1299
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: FIN-TUBE HEAT EXCHANGER, HEAT TRANSFER
-
Turbulence model evaluation for numerical modelling of turbulent flow and heat transfer of nanofluids
PublikacjaIn this work, Nusselt number and friction factor are calculated numerically for turbulent pipe flow (Reynolds number between 6000 and 12000) with constant heat flux boundary condition using nanofluids. The nanofluid is modelled with the single-phase approach and the simulation results are compared with experimental data. Ethylene glycol and water, 60:40 EG/W mass ratio, as base fluid and SiO2 nanoparticles are used as nanofluid...
-
Combined Heat & Power Generating Systems
PublikacjaSteam cycles in combined heat and power plants. Efficiency of combined heat and power systems. Characteristics of steam-turbine CHP plants. Choice of equipment in CHP generating systems. Economic effects of combined heat and power production. Costs and energy produced CHP generating systems. Future development trends in CHP generating systems.
-
Comparison of various flow maldistribution quantification methods in mini heat exchangers
PublikacjaThe aim of study is to compare various flow maldistribution quantification methods, using velocity, mass flow rate, pressure, and temperature. An experimentally validated numerical study has been prepared and a heat exchanger with 34 semi-circular channels with a diameter of 3.1 mm has been tested. The minichannels were heated from the bottom with a heat flux of 50, 60, 70, and 80 kW/m2. The cases for various inlet velocities of...
-
NUMERICAL HEAT TRANSFER PART B-FUNDAMENTALS
Czasopisma -
Heat and mass transfer in air-fed pressurised suits
PublikacjaOpisano konieczność modelowania transportu masy i ciepła w kombinezonach ochronnych. Omówiono różne sposoby modelowania wymiany ciepła, łącznie ze sprzężoną wymianą ciepła. Uwzględniono również ludzki metabolizm i turbulentne mechanizmy wymiany masy i ciepła. Publikacja opisuje również sposób modelowanie turbulentnych przepływów wieloskładnikowych. Pokazano również porównanie obliczeń z eksperymentem.
-
Determining heat transfer coefficients using evolutionary alogrithms
PublikacjaPokazano sposób kalibracji współczynnika wymiany ciepła za pomocą algorytmów ewolucyjnych. Wykorzystano tu minimalizację błędu między pomiarami a obliczeniami. Pokazano dwie metody optymalizacji: wielokryterialną i jednokryterialną.
-
Heat transfer in fluidized and fixed beds of adsorption chillers
Publikacja -
Analysis of heat transfer in a coated bed of an adsorption chiller
Publikacja -
Thermochromic liquid crystals applied for heat transfer research
PublikacjaAutorzy opisali własne wieloletnie doświadczenia z badań wymiany ciepła, w których wykorzystali termochromatyczne ciekłe kryształy. Obejmowały one badania przepływów w kanałach o różnorakiej konfiguracji, badania w przestrzeniach zamkniętych oraz podczas zmiany stanu skupienia badanego płynu.
-
The use of thermochromic liquid crystals in heat transfer research
PublikacjaW ostatnich latach ciekłe kryształy zostały z powodzeniem zastosowane do wizualizacji pola temperatury w stanach ustalonych i przejściowych na różnych powierzchniach. Analiza otrzymanych obrazów początkowo była skomplikowana, ale dzięki zastosowaniu obróbki komputerowej pomiary stały się o wiele dokładniejsze i szybsze. W opracowaniu przedstawiono przegląd badań, w których zastosowano automatyczną technikę analizy obrazów, a prowadzone...
-
Natural convective heat transfer from isothermal cuboids
PublikacjaPrzestawiono rozważania teoretyczne i wyniki badań eksperymentalnych konwekcyjnej wymiany ciepła od powierzchni izotermicznego prostopadłościanu. W rozwiązaniu analitycznym uwzględniono pełną długość warstwy przyściennej i sposób jej rozchodzenia się wzdłuż powierzchni prostopadłościanu. W celu zweryfikowania otrzymanego rozwiązania przeprowadzono badania eksperymentalne w trzech możliwych położeniach bryły. Zaproponowano uniwersalną...
-
Heat transfer augmentation visualized by liquid crystal thermography
PublikacjaW pracy przedstawiono możliwości wykorzystania termografii ciekłokrystalicznej do badań wymiany ciepła oraz wizualizacji pola przepływu w elementach urządzeń przemysłowych.
-
Heat and mass transfer in air-fed pressurised suits
PublikacjaOpisano konieczność modelowania transportu masy i ciepła w kombinezonach ochronnych. Omówiono różne sposoby modelowania wymiany ciepła, łącznie ze sprzężoną wymianą ciepła. Uwzględniono również ludzki metabolizm i turbulentne mechanizmy wymiany masy i ciepła. Publikacja opisuje również sposób modelowanie turbulentnych przepływów wieloskładnikowych. Pokazano również porównanie obliczeń z eksperymentem.
-
Convective heat transfer inside hemispherical reflective concentrator.
PublikacjaW pracy przedstawiono uproszczone rozwiązanie analityczne, obliczenia numeryczne wykonane za pomocą programu FLUENT/UNS i wyniki badań eksperymentalnych swobodnej konwekcyjnej wymiany ciepła wewnątrz izotermicznej powierzchni kołowej w przestrzeni nieograniczonej. Wykonane obserwacje bezpośrednie konwekcyjnych struktur przepływu, jak i wyniki obliczeń numerycznych otrzymane w postaci pola prędkości i linii prądu wewnątrz...
-
Heat exchange enhancement of jet impingement cooling with the novel humped-cone heat sink
PublikacjaJet impingement cooling technology is applicable to control temperature of devices, where very high heat flux is generated within a small area. This paper is about the improvement of the jet impingement cooling efficiency by the heat sink geometry modification. Two reference cases were sourced from the literature – flat heat sink and modified one with cone in the jet stagnation region. Such a change improves cooling capability...
-
Janusz Cieśliński prof. dr hab. inż.
OsobyUrodził się 15 kwietnia 1954 r. w Słupsku. Jest absolwentem Wydziału Budowy Maszyn Politechniki Gdańskiej (1978), z którą związał całe swoje życie zawodowe. W 1986 r. obronił doktorat, w 1997 r. – habilitację, w 2006 r. – uzyskał tytuł profesora. Pełnił funkcje prodziekana ds. nauki Wydziału Mechanicznego przez dwie kadencje (2002–2008) oraz kierownika: Katedry Maszyn Przemysłu Spożywczego (2002–2006), Katedry Ekoinżynierii i...
-
Recent Advances in Loop Heat Pipes with Flat Evaporator
PublikacjaThe focus of this review is to present the current advances in Loop Heat Pipes (LHP) with flat evaporators, which address the current challenges to the wide implementation of the technology. A recent advance in LHP is the design of flat-shaped evaporators, which is better suited to the geometry of discretely mounted electronics components (microprocessors) and therefore negate the need for an additional transfer surface (saddle)...
-
Application of Feed Forward Neural Networks for Modeling of Heat Transfer Coefficient During Flow Condensation for Low and High Values of Saturation Temperatur
PublikacjaMost of the literature models for condensation heat transfer prediction are based on specific experimental parameters and are not general in nature for applications to fluids and non-experimental thermodynamic conditions. Nearly all correlations are created to predict data in normal HVAC conditions below 40°C. High temperature heat pumps operate at much higher parameters. This paper aims to create a general model for the calculation...
-
Current Trends in Wick Structure Construction in Loop Heat Pipes Applications: A Review
PublikacjaThermal control systems have been introduced as an important part of electronic devices, enabling thermal management of their electronic components. Loop heat pipe (LHP) is a passive two-phase heat transfer device with significant potential for numerous applications, such as aerospace applications, high-power LEDs, and solar central receivers. Its advantages are high heat transfer capability, low thermal resistance, long-distance...
-
Utilisation of waste heat from the power plant by use of the ORC aided with bleed steam and extra source of heat
PublikacjaUtilization of waste heat recovered from the exhaust gases of the power generation unit by means of ORC (organic Rankine cycles) installation is considered. The waste heat is available in the form of a stream of hot water having temperature of 90 stC in the amount of 200 MWt. To increase evaporation temperaturę of ORC working fluid the heat of steam from the extraction points from the low-pressure part of steam turbine is used....
-
Heat Turbomachinery 2023_24
Kursy OnlineBasics of thermodynamical cycles. Elements of turbine power plants. Fluid problems in turbomachinery. Theory of turbine stages. Turbine flow parts.
-
Influence of the thermal modernization of window on transmission heat losses
PublikacjaThe article presents the results of calculations of the heat transfer coefficient for the state before and after renovation for the historic windows. The aim of the analysis was to obtain the values of thermal insulation parameters demanded by the regulations, while not losing the historical value of the window. The described example of the renovation of the existing window consisted in installing an additional window panel from...
-
Modelling heat transfer in heterogeneous media using fractional calculus
Publikacja -
Modeling Heat Transfer in Heterogeneous Media Using Fractional Calculus
Publikacja -
Model of heat transfer in the stagnation point of rapidly evaporating microjet
PublikacjaThe paper presents investigation in the single water microjet surface cooling producing evaporating film. Reported tests were conducted under steady state conditions. It was proved that the phenomenon is similar to that of pool boiling. Results of experiments were compared with predictions by the model showing a good consistency.
-
Measurements of heat transfer enhanced by the use of transverse vortex generators
PublikacjaArtykuł dotyczy badań eksperymentalnych wymiany ciepła w modelowym wymienniku ciepła z turbulizatorami przepływu dla różnej geometrii turbulizatorów. Badania wykonano przy użyciu termografii ciekłokrystalicznej i cyfrowej anemometrii obrazowej.
-
Measurements of heat transfer enhanced by the use of transverse vortex generators
PublikacjaArtykuł dotyczy badań eksperymentalnych intensyfikacji wymiany ciepła w modelowym wymienniku ciepła z turbulizatorami przepływu dla różnej geometrii turbulizatorów. W badaniach zastosowano termografię ciekłokrystaliczną i cyfrową anemometrię obrazową.
-
Heat transfer enhancement through nanofluids with applications in automobile radiator
Publikacja -
Convective momentum and heat transfer in single and two-phase flows
PublikacjaW pracy przedstawiono dorobek autora w zakresie modeowania wymiany pędu i ciepław w przepływach jedno i dwufazowych.
-
Numerical heat transfer model in skin burn depth simulations
PublikacjaW artykule przedstawiono numeryczny model wymiany ciepła zachodzącej w tkance skórnej . Wyniki symulacji na modelu zostały porównane z wynikami pomiarów In vivo na zwierzętach.
-
Numerical modeling of cross-flow heat exchanger for air-conditioning purposes in preliminary study.
PublikacjaPraca przedstawia wyniki obliczeń numerycznych krzyżowego płytowo-rurowego wymiennika ciepła przeznaczonego do celów klimatyzacyjnych w początkowym etapie jego projektowania.
-
High-efficiency mini and micro heat exchangers for dispersed power generation
PublikacjaTaking into account the dispersed systems technologies and their development, the ORC systems seem to be promising technology amongst various micro-CHP domestic units (electrical power production below 10 kWe), however practical realization of the ORC cycle in a micro-scale is technically challenging. The system consists in devices such as the vapour generation unit (boiler), expansion device and heat exchangers. Each of them should...
-
Heat and mass transport
Kursy OnlineCelem przedmiotu jest przekazanie wiedzy o podstawowych mechanizmach i prawach procesów transportu ciepła i masy, pozwalającej na rozwiązywanie inżynierskich problemów związanych z projektowaniem urządzeń i aparatury wymiany ciepła i masy.
-
Heat and mass transport
Kursy Online -
Heat and mass transport
Kursy Online -
JOURNAL OF THERMOPHYSICS AND HEAT TRANSFER
Czasopisma -
Green function diagonal for a class of heat equations
PublikacjaA construction of the heat kernel diagonal is considered as element of generalized zeta function theory, which gradient at the origin defines determinant of a differential operator in a technique for regularizing quadratic path integral. Some classes of explicit expressions of the Green function in the case of finite-gap potential coefficient of the heat equation are constructed. An algorithm and program for Mathematica are presented...
-
Heat Dissipation from the Power Cable in the Casing Pipe
PublikacjaThe current carrying capacity of a power cable determines its ability to carry a specific current and is related to the efficiency of dissipation of heat generated in the cable laid in a specific environment. The studies were conducted in order to determine how the characteristics of the medium around the cable affected its temperature, and thus the ability of the cable to transmit electricity. The experimentation in the lab and...
-
Heat tint colours on stainless steel and welded joints
PublikacjaSurface layer condition of stainless steels and welded joints influences strongly their corrosion resistance. This problem seems to be underestimated. This current study explains the phenomenon of heat tint forming on welds, the methods of its removal, inspection procedures after heat tint removing and post weld finishing
-
HIGH TEMPERATURE HEAT PUMPS – PERSPECTIVE HEATING SYSTEMS?
PublikacjaIn the paper presented are authors own concepts of high temperature compressor heat pumps for the utilisation of medium and low temperature sources of heat. Working fluids for use in high temperature heat pumps are discussed, as well as the criteria for their selection. Analyses are presented for the production of in the upper steam source at 130 °C. One-stage systems and cascade systems were analyzed. An analysis of the coefficient...
-
A device for measuring heat flux on a rocket skin surface
PublikacjaA novel method for measuring heat flux on a surface is presented. It is an extensive upgrade of currently known heat flux sensors used mostly in civil engineering. As the thermal environment of launchers, especially sounding rocket can have an enormous negative effect on payload, careful considerations have to be taken in the process of preparing insulation. Usually, thermal data provided by the launch vehicle manufacturer is limited...
-
Gas boiler as a heat source for the domestic micro-CHP
PublikacjaThis analysis considers a commercially available domestic gas boiler as a heat source for a domestic organic Rankine cycle system. An experimental study was made into the applicability of the gas boiler (De Dietrich with thermal power 25 kW) coupled with the laboratory prototype micro ORC setup. The main aim of the study is to determine the working fluid temperature, attainable heat rates and effciencies of the whole system. Preliminary...
-
Gas boiler as a heat source for the domestic micro-CHP
PublikacjaIn the presented analysis a commercially available domestic gas boiler as a heat source for domestic ORC is considered. The applicability of the gas boiler (De Dietrich with thermal power 25 kW) coupled with the laboratory prototype micro ORC setup has experimentally studied. The main aim of the study is to determine the working fluid temperature, attainable heat rates and efficiencies of the whole system. Preliminary investigations...
-
Numerical methods in heat and fluid flow, PG_00057408
Kursy OnlineReiteration of information on thermodynamic cycles and extension of information on their modelling using commercial software tools. Presentation of balances, constitutive equations, how to set up conditions in CFD type codes. Equipment regulation and control in the context of heat exchangers.Presentation of the computational capabilities of the CFD calculation code ANSYS Fluent. Mass, momentum and energy balances in 0D and 3D terms.Analysis...
-
Corrosion-erosion damage of heat exchanger tubes by desalted crude oil flowing at shell side
Publikacja -
Corrosion-erosion damage of heat exchanger tubes by desalted crude oil flowing at shell side.
PublikacjaRurki wymiennika zostały uszkodzone lokalnie przez odsoloną ropę naftową przepływającą pod ciśnieniem 2,6 MPa i w temperaturze 385-395K. Większość powierzchni rurek nie była uszkodzona i była pokryta osadem związków organicznych i nieorganicznych, zabezpieczającym przed uszkodzeniami. Badania wykluczyły możliwość występowania intensywnej korozji elektrochemicznej na powierzchniach rurek pozbawionych osadu. Przyczyną perforacji...
-
Nuclear power plant as a source of electrical energy and heat
PublikacjaIn this paper certain issues concerning usage of nuclear power plants as sources of not only electric power but also thermal energy will be discussed. For such a solution appeals most of all the need to limit harmful emissions of gases (including CO2) and ashes, which come from the process of burning fossil fuels, as well as the raising demand for network heat and chill. Additionally combined heat and power production brings measurable...
-
Experimental study of heat transfer intensification in surface cooling using microjets
PublikacjaW pracy przedstawiono badania eksperymentalne intensyfikacji wymiany ciepła podczas chłodzenia powierzchni mikrostrugami. Wyniki badań porównano z własnym modelem teoretycznym zjawiska.
-
A comparative study of different methods for heat transfer enhanced by the use of TVG
PublikacjaArtykuł dotyczy badań eksperymentalnych i numerycznych intensyfikacji wymiany ciepła w modelowym wymienniku ciepła z turbulizatorami przepływu dla różnej geometrii turbulizatorów. Do badań eksperymentalnych wykorzystano termografię ciekłokrystaliczną a modelowanie fizyczne wykonano za pomocą kodu komputerowego FLUENT.
-
The Numerical Comparison of Heat Transfer in a Coated and Fixed Bed of an Adsorption Chiller
Publikacja