Wyszukiwarka
Filtry
wszystkich: 1549
-
Katalog
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: FLUE GAS DESULPHURIZATION
-
Electrochemical investigations of stainless steels used in flue‐gas desulphurization units
Publikacja -
Assessment of protective properties of rubber lining in absorbers of flue gas desulphurization systems.
PublikacjaResults of research on degradation of rubber lining which is the main protection of absorbers in flue gas desulphurization (FGD) systems were presented. The power plant where the system operated is lignite-fired. Owing to measurements using electrochemical impedance spectroscopy and gravimetric determination of water content in the lining, the areas of the system which are most exposed to degradation were shown. The results obtained...
-
Anti‐corrosion protection of chimneys and flue gas ducts
Publikacja -
Inspection of rubber linings operating in flue gas desulphurisation units
Publikacja -
OPTIMALIZATION OF SORBENT FEEDING IN THE DRY METHOD OF FLUE GAS DESULFURIZATION
PublikacjaThe swiftly developing sea transport contributes to a considerable increase of fuel usage in the international shipping, which results in the escalation of toxic compounds emitted into the atmosphere. It is followed by the constantly heightened requirements limiting those emissions. In the case of sulfur oxide emission, inside of SECA (Sulfur Emission Control Area), the maximum content of sulfur in the shipping fuels used on the...
-
Degradation of protective coatings in steel chimneys of flue gas desulfurisation system
PublikacjaThis paper presents problems associated with corrosion of steel stacks and changes in philosophy of corrosion protection when implemented into flue gas desulphurization systems. In-situ tests were taken by means of electrochemical impedance spectroscopy at the stack which discharges flue gas before wet lime/limestone desulphurization. A very quick electrolyte absorption by the spherical infill vinylester coating was found using...
-
Flue gas treatment for SO2 removal with air-sparged hydrocyclone technology
PublikacjaWyniki badań dowodzą, że reaktor cyklonowy jest wysokosprawnym absorberem. Absorber cyklonowy pozwala na osiągnięcie stopnia redukcji 97% dla samej wody i zawartości dwutlenku siarki w fazie gazowej 5 mg/dm3. Dwutlenek siarki był usuwany również w wodnym rozworze alkaicznym (0.01 mol NaOH/dm3).
-
Flue gas treatment for SO2 removal with air-sparged hydrocyclone technology
PublikacjaOpisano wstępne wyniki badań laboratoryjnych usuwania SO2 z mieszaniny gazów z zastosowaniem reaktora cyklonowego (ASH). Do absorpcji stosowano wodę wodociągową oraz roztwór alkaliów. Zbadano wpływ natężenia przepływu gazu, natężenia przepływu wody oraz długość elementów ASH. Stwierdzono, że efektywność absorpcji SO2 z powietrza stosując technologię ASH jest porównywalna z efektywnością metod konwencjonalnych.
-
Research on flue gas flow measurement and modelling in the moving grate biomass boiler
PublikacjaThe aim of this research was to determine the nature of gas flow in a grate boiler model by the method of Particle Image Velocimetry (PIV) and CFD. The paper presents the comparison of the PIV results with numerical simulations made in the environment of ANSYS Fluent. The main goal of the experiment was to describe the phenomena occurring on the grate. Methodology of modelling solid fuel combustion on the moving grate was proposed...
-
Separation of CO2 from flue gas in air-sparged hydrocyclone (ash) reactor
PublikacjaPrzedmiotem badań była absorpcja dwutlenku węgla w wodnym roztworze wodorotlenku sodu, z fazy gazowej w skali laboratoryjnej i technologicznej z wykorzystaniem reaktora typu ash. Natężenie przepływu powietrza wynosiło 900 dm3/min a wodnego roztworu NaOH 15 dm3/min w skali technologicznej. Zbadano stężenie CO2, pH w fazie ciekłej, wpływ natężenia przepływu fazy gazowej i fazy ciekłej na efektywność absorpcji
-
Experimental investigation of utilizing waste flue gas desulfurized gypsum as backfill materials
Publikacja -
Experimental and numerical investigation of mercury removal from flue gas by sorbent polymer composite
PublikacjaThis paper presents an experimental and numerical investigation of the performance of a sorbent polymer composite (SPC) material used for removing mercury from the flue gases in a full-scale industrial installation. The investigated material is an attractive alternative to activated carbon, which is commonly used for this purpose. While the application of the SPC is characterized by high capital expenditures, this technology offers...
-
Use of Impedance Spectroscopy to Characterize Lining Performance in Simulated Flue Gas Desulfurization Systems
Publikacja -
Reliability of flue gas desulphurisation installations - the essential condition of efficient air pollution control
PublikacjaW celu minimalizacji niekorzystnego wpływu SO2 i SO3 na środowisko naturalne w wielu instalacjach skrubery odsiarczające gaz spalinowy (FGD) stosowane są do usuwania tlenków siarki z gazów wylotowych. Ostre warunki pracy skruberów i dodatkowego osprzętu powodują problemy korozyjne w powszechnie stosowanych materiałach konstrukcyjnych a awarie wywierają długookresowy wpływ na środowisko. Opisano najnowsze doświadczenia związane...
-
Durability evaluation of Ni‐Cr‐Mo super alloys in a simulated scrubbed flue gas environment
Publikacja -
Ammonia in Fly Ashes from Flue Gas Denitrification Process and its Impact on the Properties of Cement Composites
Publikacja -
Nitrogen oxides removal from hydrogen flue gas using corona discharge in marine boilers: Application perspective
PublikacjaThis paper focuses on the combustion of hydrogen in boilers, as it appears to be a more effective method than using fuel cells for heating purposes due to higher boiler efficiency. One of the main disadvantages of hydrogen combustion in air is NOx formation. Therefore, the authors decided to introduce corona discharge as an inno- vative technique to clean hydrogen flue gas by effectively reducing NOx levels. The method involves...
-
Inspection of rubber linings operating in flue gas desulphurisation units. Inspekcje wykładzin gumowych w warunkach instalacji odsiarczania spalin.
PublikacjaPomiary metodą EIS wykładzin gumowych przeprowadzono w warunkach polowych.Stwierdzono, że najlepszym miernikiem jakości powłoki jest pojemność elektryczna powłoki. Sposób wyznaczania zwartości wilgoci w powłoce oparty został na równaniu Brashera-Kingsbury´ego. Wyniki porównano z oznaczeniami wilgoci w wykładzinie metodami niszczącymi przeprowadzonymi w tych samych miejscach co badania elektrochemiczne.
-
Emission characteristics for gaseous- and size-segregated particulate PAHs in coal combustion flue gas from circulating fluidized bed (CFB) boiler
Publikacja -
PROBLEMS WITH CORROSION PROTECTION STEEL STACKS IN FGD SYSTEMS
PublikacjaThis paper presents problems associated with corrosion of steel stacks and changes in philosophy of corrosion protection when implemented into flue gas desulphurization systems. In-situ tests were taken by means of electrochemical impedance spectroscopy at a stack which discharges flue gas before wet lime/limestone desulphurization. A very rapid soaking of spherical infill vinylester coating with electrolyte has been observed....
-
State of the art in the field of emission reduction of sulphur dioxide produced during coal combustion
PublikacjaThe need for clean coal technologies to reduce the adverse environmental impact of coal combustion products has been grounded. The article deals with information concerning present and future technologies, directed towards the struggle against air pollution by SO2, produced during coal combustion. Their classification and critical rating from economical and technological points of views (including those developed by authors) have...
-
Kazimierz Darowicki prof. dr hab. inż.
OsobyStudia wyższe ukończyłem w czerwcu 1981 roku po zdaniu egzaminu dyplomowego i obronie pracy magisterskiej. Opiekunem pracy magisterskiej był dr hab. inż. Tadeusz Szauer. W roku 1991, 27 listopada uzyskałem stopień naukowy broniąc pracę doktorską zatytułowaną „Symulacyjna i korelacyjna analiza widm immitancyjnych inhibitowanej reakcji elektrodowej”. Promotorem pracy był prof. dr hab. inż. Józef Kubicki (Wydział Chemiczny...
-
Fundamentals of Steam and Gas Turbines OASIV
Kursy OnlineApplication of turbines in industry and sea power plants. Basic thermodynamics and fluid flow mechanics in turbomachinery. Steam turbine power cycle and plants. Gas turbine power cycle and plants. Turbine blading systems operation.
-
Sounding Mechanism of a Flue Organ Pipe—A Multi-Sensor Measurement Approach
PublikacjaThis work presents an approach that integrates the results of measuring, analyzing, and modeling air flow phenomena driven by pressurized air in a flue organ pipe. The investigation concerns a Bourdon organ pipe. Measurements are performed in an anechoic chamber using the Cartesian robot equipped with a 3D acoustic vector sensor (AVS) that acquires both acoustic pressure and air particle velocity. Also, a high-speed camera is employed...
-
On Accuracy Modeling of Gas Turbine Cycles by the In-house COM-GAS Code
PublikacjaIn this paper, a comparison of accuracy modeling of gas turbine cycles between the basic (classical) model and the in-house COM-GAS code has been presented. The basic model uses a semi-perfect gas and well known projecting assumption. On the other hand, the computational flow mechanics (CFM) basis on a real gas by using thermodynamic tables. The thermodynamic analysis of thermal cycles, simply gas cycle GT8C and gas turbine cycle...
-
Steam and Gas Turbines Constuction_ seminar/project
Kursy Online -
Efficiency of gas mixtures detection by resistive gas sensors
PublikacjaResistive gas sensors are very popular and are commonly used to detect various gases and their mixtures. Theeir main disadvantage is very limited selectivity. Practical use of gas sensors in environenmental applications requires determination of concentration of a few mixed gases at the same time. We would like to present recent results of gas detection improvement by utilizing a single gas sensor and additional measurements to...
-
EFFICIENCY OF GAS MIXTURES DETECTION BY RESISTIVE GAS SENSORS
PublikacjaResistive gas sensors are very popular and are commonly used to detect various gases and their mixtures. Their main disadvantage is very limited selectivity. Practical use of gas sensors in environmental applications (e.g., in sewage systems to protect workers, in air conditioning systems to monitor atmosphere quality) requires determination of concentration of a few mixed gases at the same time. We would like to present recent...
-
Selectivity of amperometric gas sensors in multicomponent gas mixtures
PublikacjaIn recent years smog and poor air quality became a growing environmental problem. There is a need to continuously monitor the quality of air. The lack of selectivity is one of the most important problems limiting the use of gas sensors for this purpose. In this study, a selectivity of the six amperometric gas sensors is being investigated. Calibration of sensors has been performed in order to find a correlation between concentration...
-
Gas sampling system for matrix of semiconductor gas sensors
PublikacjaSemiconductor gas sensors are popular commercial sensors applied in numerous gas detection systems. They are reliable, small, rugged and inexpensive. However, there are a few problem limiting the wider use of such sensors. Semiconductor gas sensor usually exhibits a low selectivity, low repeatability, drift of response, strong temperature and moisture influence on sensor properties. Sample flow rate is one of the parameters that...
-
Application of Thermo-chemical Technologies for Conversion of Associated Gas in Diesel-Gas Turbine Installations for Oil and Gas Floating Units
PublikacjaThe paper considers the issue of thermo-chemical recovery of engine’s waste heat and its further use for steam conversion of the associated gas for oil and gas floating units. The characteristics of the associated gas are presented, and problems of its application in dual-fuel medium-speed internal combustion engines are discussed. Various variants of combined diesel-gas turbine power plant with thermo-chemical heat recovery are...
-
Gas selectivity enhancement by sampling-and-hold method in resistive gas sensors
PublikacjaCommercial resistive gas sensors exhibit various sensitivity to numerous gases when working at different elevated temperatures. That effect is due to a change in velocity of adsorption and desorption processes which can be modulated by temperature. Thus, to reach better selectivity of gas detection, we propose to apply a known method (called the sampling-and-hold method) of cooling down the gas sensor in the presence of the investigated...
-
SAMPLE-AND-HOLDING METHOD FOR GAS SENSING APPLIED FOR RESISTANCE GAS SENSORS
PublikacjaThe DC resistance of a Taguchi gas sensor is influenced by the ambient gas. To improve the selectivity and sensitivity of a sensor the fluctuation enhanced sensing (FES) was used. The paper proposes a novel methodology of utilizing FES technique that sample composition of an ambient atmosphere and hold it for further processing (sample-and-holding technique). The method uses the heated gas sensor to sample an ambient atmosphere...
-
Flicker Noise in Resistive Gas Sensors—Measurement Setups and Applications for Enhanced Gas Sensing
PublikacjaWe discuss the implementation challenges of gas sensing systems based on low-frequency noise measurements on chemoresistive sensors. Resistance fluctuations in various gas sensing materials, in a frequency range typically up to a few kHz, can enhance gas sensing by considering its intensity and the slope of power spectral density. The issues of low-frequency noise measurements in resistive gas sensors, specifically in two-dimensional...
-
GRAPHENE IN GAS CHEMIRESISTORS
PublikacjaGraphene has a range of unique physical properties which could be exploited in gas sensing. Every atom of graphene may be considered as a surface atom, able to interact even with single molecule of the target gas or vapour species resulting in the ultrasensitive sensor response. In this paper the potential of graphene as a nanomaterial for fabricating chemiresistors was described. Recent development in graphene sensors was considered...
-
Gas Detection Using Resistive Gas Sensors And Radial Basis Function Neural Networks
PublikacjaWe present a use of Radial Basis Function (RBF) neural networks and Fluctuation Enhanced Sensing (FES) method in gas detection system utilizing a prototype resistive WO3 gas sensing layer with gold nanoparticles. We investigated accuracy of gas detection for three different preprocessing methods: no preprocessing, Principal Component Analysis (PCA) and wavelet transformation. Low frequency noise voltage observed in resistive gas...
-
Investigation of the Combustion Processes in the Gas Turbine Module of an FPSO Operating on Associated Gas Conversion Products
PublikacjaIn this paper, we consider the issue of thermo-chemical heat recovery of waste heat from gas turbine engines for the steam conversion of associated gas for offshore vessels. Current trends in the development of offshore infrastructure are identified, and the composition of power plants for mobile offshore drilling units and FPSO vessels is analyzed. We present the results of a comparison of power-to-volume ratio, power-to-weight...
-
Limited selectivity of amperometric gas sensors operating in multicomponent gas mixtures and methods of selectivity improvement
PublikacjaIn recent years, smog and poor air quality have became a growing environmental problem. There is a need to continuously monitor the quality of the air. The lack of selectivity is one of the most important problems limiting the use of gas sensors for this purpose. In this study, the selectivity of six amperometric gas sensors is investigated. First, the sensors were calibrated in order to find a correlation between the concentration...
-
Energy requirements for methods improving gas detection by modulating physical properties of resistive gas sensors
PublikacjaAbstract. One of the most important disadvantage of resistive gas sensors is their limited gas selectivity. Therefore, various methods modulating their physical properties are used to improve gas detection. These methods are usually limited to temperature modulation or UV light irradiation for the layers exhibiting photocatalytic effect. These methods cause increased energy consumption. In our study we consider how much energy...
-
Portable exhaled breath analyzer employing fluctuation-enhanced gas sensing method in resistive gas sensors
PublikacjaThis paper presents a portable exhaled breath analyser, developed to detect selected diseases. The set-up employs resistive gas sensors: commercial MEMS sensors and prototype gas sensors made of WO3 gas sensing layers doped with various metal ingredients. The set-up can modulate the gas sensors by applying UV light to induce physical changes of the gas sensing layers. The sensors are placed in a tiny gas chamber of a volume...
-
Extraction and evaluation of gas-flow-dependent features from dynamic measurements of gas sensors array
PublikacjaGas analyzers based on gas sensors are the devices which enable recognition of various kinds of volatile compounds. They have continuously been developed and investigated for over three decades, however there are still limitations which slow down the implementation of those devices in many applications. For example, the main drawbacks are the lack of selectivity, sensitivity...
-
INVESTIGATION OF THE CHARACTERISTICS OF A LOWEMISSION GAS TURBINE COMBUSTION CHAMBER OPERATING ON A MIXTURE OF NATURAL GAS AND HYDROGEN
PublikacjaT his article is devoted to the investigation of the characteristics of a low-emission gas turbine combustion chamber, which can be used in Floating Production, Storage and Offloading (FPSO) vessels and operates on a mixture of natural gas and hydrogen. A new approach is proposed for modelling the processes of burning out a mixture of natural gas with hydrogen under preliminary mixing conditions in gaseous fuel with an oxidizer...
-
Oil and Gas Geology
Czasopisma -
Natural Gas Geoscience
Czasopisma -
Medical Gas Research
Czasopisma -
OIL & GAS JOURNAL
Czasopisma -
Gas Science and Engineering
Czasopisma -
Gas mixtures recognition using an array of amperometric gas sensors with drifting or faulty sensors
PublikacjaIn this study, the possibility of using selected methods for diagnostics of performance of matrix composed with six amperometric electrochemical gas sensors is investigated. Measurements of sensor responses in selected concentrations of single toxic gases or gas mixtures were performed and were repeated over time to show sensor drift. Additionally, the studies on the sensors’ drift were performed. The drift has been recognized...
-
Hydrogen sulphide electrocatalytic gas sensor
PublikacjaIn this article measurement results of the electrocatalytic gas sensor in different concentrations of hydrogen sulphide are presented. Working principle of such sensor is based on electric current acquisition, while voltage ramp is applied to the sensor. During voltage sweep oxidation and reduction reactions occurs on the sensor electrodes. Obtained current-voltage plot has unique shape connected...
-
Efficiency of linear and non-linear classifiers for gas identification from electrocatalytic gas sensor
PublikacjaElectrocatalytic gas sensors belong to the family of electrochemical solid state sensors. Their responses are acquired in the form of I-V plots as a result of application of cyclic voltammetry technique. In order to obtain information about the type of measured gas the multivariate data analysis and pattern classification techniques can be employed. However, there is a lack of information in literature about application of such...