Wyszukiwarka
Wyniki wyszukiwania dla: TURBULENT FLOW
-
Numerical Study of Turbulent Flow and Heat Transfer of Nanofluids in Pipes
PublikacjaIn this work, Nusselt number and friction factor are calculated numerically for turbulent pipe flow (Reynolds number between 6000 and 12000) with constant heat flux boundary condition using nanofluids. The nanofluid is modelled with the single-phase approach and the simulation results are compared with experimental data. Ethylene glycol and water, 60:40 EG/W mass ratio, as base fluid and SiO2 nanoparticles are used as nanofluid...
-
Numerical study of turbulent flow and heat transfer of nanofluids in pipes
PublikacjaIn this work, Nusselt number and friction factor are calculated numerically for turbulent pipe flow (6 000 < Re < 12 000) with constant heat flux boundary condition using nanofluids. The nanofluid is modelled with the single-phase approach and the simulation results are compared with experimental data of Vajjha et al. [1]. Ethylene glycol and water, 60:40 EG/W mass ratio, as base fluid and SiO2 nanoparticles are used as nanofluid...
-
A numerical and experimental analysis of multi-hole orifice in turbulent flow
PublikacjaIn this research study, the comprehensive metrological analysis is investigated for a 4-hole orifice with module m = 0.25 installed in the pipeline with an internal diameter of 50 mm. A detailed numerical simulation was performed for the turbulence models: k-ε-realizable and k-ω-BSL. The novelties of the research include model validation by comparing the results of numerical studies with the experiment conducted in the area of...
-
Analysis of Turbulent Flow Measurements in a Flume with Induced Upward Seepage
Publikacja -
Numerical single-phase modeling of turbulent flow and heat transfer of nanofluids
PublikacjaIn this work, Nusselt number and friction factor are calculated numerically for turbulent pipe flow (6 000< Re < 12 000) with constant heat flux boundary condition using nanofluids. The nanofluid is modelled with the single-phase approach and the simulation results are compared with published experimental data.
-
Turbulent flow and heat transfer of a liquid film formed by impinging jet.
PublikacjaZaproponowano prosty model wymiany ciepła w turbulentnym filmie cieczowym utworzonym przez uderzająca strugę. Rozpatrzono dwa przypadki: przepływ rozwijający się i w pełni rozwinięty filmu cieczowego. W obu przypadkach model wyprowadzono na podstawie zmiany grubości filmu w wyniku działania sił bezwładności i sił tarcia. Wyznaczono profile prędkości w obu zakresach co umożliwia wyznaczenie współczynników wymiany ciepła.
-
Turbulence model evaluation for numerical modelling of turbulent flow and heat transfer of nanofluids
PublikacjaIn this work, Nusselt number and friction factor are calculated numerically for turbulent pipe flow (Reynolds number between 6000 and 12000) with constant heat flux boundary condition using nanofluids. The nanofluid is modelled with the single-phase approach and the simulation results are compared with experimental data. Ethylene glycol and water, 60:40 EG/W mass ratio, as base fluid and SiO2 nanoparticles are used as nanofluid...
-
Numerical Analysis of Turbulent Flow over a Backward-facing Step in an Open Channel
PublikacjaComputational examinations of the flow field in an open channel having a single Backward--Facing Step (BFS) with a constant water depth of 1.5 m were performed. The effects of the expansion ratio, and the flow velocity along the reattachment length, were investigated by employing two different expansion ratios of 1.5 and 2, and eight various flow velocities of 0.5, 1, 2, 3, 4, 5, 7.5 and 10 m/sec in the Computational Fluid Dynamic...
-
Anisotropic stochastic dispersion model for large-eddy simulations of particle-laden turbulent flows
Publikacja -
Hydrodynamics and heat transfer in bubbly flow in the turbulent boundarylayer
PublikacjaW pracy przedstawiono oryginalne podejście do modelowania przepływu pęcherzykowego w warstwie przyściennej i w kanale. Podejście oparte jest na sumowaniu energii dyssypacji pochodzącej od przepływu ścinającego w kanale oraz dyssypacji pochodzącej od obecności pęcherzyków. W wyniku otrzymuje się naprężenia styczne ekwiwalentnego przepływu jednofazowego. Zaproponowano własne podejście do modelowania stopnia zapełnienia opisane równaniem...
-
Erosion under turbulent slurry flow: An experimental determination of particle impact angle, impact direction, and distribution thereof by image processing
Publikacja -
Flow of liquid in flat gaps of the satellite motor working mechanism
PublikacjaThe article describes the methodology and results of investigations of the flow of oil and HFA-E emulsion in flat gaps of the working mechanism of a satellite motor. The flow of liquid in those gaps is turbulent and not fully developed. The article presents two methods of modelling this flow. Method I makes use of the Darcy-Weisbach formula, while Method II bases on the assumption that in the variable-length gaps the flow is turbulent...
-
Determination of Mechanical Energy Loss in Steady Flow by Means of Dissipation Power
PublikacjaWhen systems of simple geometry like pipes or regular channels are considered, the mechan- ical energy loss of the fluid flow can be expressed by local and longitudinal empirical energy loss coefficients. However, in the case of large spatially distributed objects, there are no simple approaches to this task. In practice, general recommendations addressing different types of objects are used, but they usually provide very coarse...
-
Modelling of two-component turbulent mass and heat transfer in air-fed pressurised suits
PublikacjaIn this paper the modelling of an important industrial problem is addressed, which involves the two-component turbulent flow with heat transfer that takes place inside protective clothing. The geometry of the flow boundaries is reconstructed in a CAD system from photogrammetry scan data. The overall model is sufficiently realistic to allow, after validation, design improvements to be tested. Those presented here allow the reduction...
-
Numerical simulation of cold flow and combustion in a swirl stabilized combustor
PublikacjaA numerical simulation model was developed to investigate the cold flow and combustion using Ansys FLUENT 2021R1. The governing equations were solved using the pressure-based method, and pressure–velocity coupling was performed using the SIMPLE method. To model the turbulent process, the RSM model was used. Non-premixed model is chosen to solve the chemical kinetics between fuel and oxigen. Radiation heat transfer was calculated...
-
Recent progress in experimental studies of electrohydrodynamic flow in electrostatic precipitators
PublikacjaMany experimental, theoretical and numerical works were devoted to the electrohydrodynamic (EHD) flow generated in electrostatic precipitators (EPSs). The generally accepted conclusion from these studies is that the EHD flow plays an important role in the particle collection in ESPs. However, despite of the recent fast progress in numerical simulation and experimental techniques used in the ESPs studies many problems related to...
-
Air flow phenomena in the model of the blind drift
PublikacjaIn the presented paper, Particle Image Velocimetry (PIV) has been used to investigate flow pattern and turbulent structure in the model of blind drift. The presented model exist in mining, and has been analyzed to resolve ventilation issues. Blind region is particularly susceptible to unsafe methane accumulation. The measurement system allows us to evaluate all components of the velocity vector in channel cross-section simultaneously....
-
Computational Fluid Dynamics Simulation of Gas–Liquid Multiphase Flow in T-junction for CO2 Separation
PublikacjaThe article presents the results of a computational fluid dynamics (CFD) analysis of gas-liquid multiphase flow. The simulation was conducted using CFD code and the Euler–Euler approach. The presented study relates to the non–reactive, steady-state, turbulent flow of water and carbon dioxide mixture in a 3D pipe. Separation phenomenon between phases is observed. The solution was obtained using a mixture model. Different values...
-
Effects of subfilter velocity modelling on dispersed phase in LES of heated channel flow
PublikacjaA non-isothermal turbulent flow with the dispersed phase is modelled using the Large Eddy Simulation (LES) approach for fluid, one-way coupled with the equations of point-particle evolution. The channel is heated at both walls and isoflux boundary conditions are applied for fluid. Particle velocity and thermal statistics are computed. Of particular interest are the r.m.s. profiles and the probability density function of particle...
-
Turbulence models impact on the flow and thermal analyses of jet impingement
PublikacjaAccurate numerical reconstruction of heat and mass transfer processes in particular applications, such a jet impingement, is difficult to obtain even with the use of modern computational methods. In the proposed paper, the flow and thermal phenomena occurring during single minijet impingement on the flat, concave and convex, heated surfaces were considered. Problem of impingement on non-flat surface, still not common and purely...
-
Impact of Temperature and Nanoparticle Concentration on Turbulent Forced Convective Heat Transfer of Nanofluids
PublikacjaTheoretical analysis of the influence of nanoparticles and temperature on the average Nusselt (Nu) number and the average heat transfer coefficient (HTC) during the turbulent flow of nanofluid in a horizontal, round tube was carried out. The Nu number is a function of the Reynolds (Re) number and the Prandtl (Pr) number, which in turn are functions of the thermophysical properties of the liquid and the flow conditions. On the other...
-
Alternative convolution approach to friction in unsteady pipe flow
PublikacjaIn the paper some aspects of the unsteady friction in pipe flow expressed by the convolution are analyzed. This additional term introduced into the motion equation involves the accelerations of fluid occurring in the past and a weighting function. The essence of such approach is to assume the appropriate form of weighting function. However, until now no fully reliable formula for this function has been found. To avoid some inconveniences...
-
Minichannel and minigap classification criteria based on the aspect ratio of the minigeometry: A numerical study
PublikacjaA detailed numerical investigation has been carried out to analyze the diabatic flow distribution and velocity profile in 18 minigeometries with various aspect ratios for V-type and I-type flow configurations (for 36 cases) assuming ethanol as a working fluid. The aim of the study is to distinguish the value of the aspect ratio for which the flow in minigeometry starts to be two-dimensional (minigap). Cases with a constant Reynolds...
-
Analysis of cyclone separator solutions depending on SEC outlet conditions in nCO2PP
PublikacjaUtilization of spray ejector condenser in order to carry out direct-contact condensation of vapour with inert gas (CO2) on a spray of subcooled liquid integrated with separator (to make pure CO2) has been proposed for the task of condensation and CO2 separation in the negative CO2 emission gas power plant. Condensation and separation has a significant impact on the thermodynamic efficiency of the entire negative CO2 emission gas...
-
Analysis of cyclone separator solutions depending on spray ejector condenser conditions
PublikacjaThe core design strategy for minimizing CO2 emissions in gas power plant entails combining a spray ejector condenser (SEC) and separator to accomplish steam condensation and CO2 purification. This innovative process involves direct-contact condensation of steam with CO2, facilitated by interaction with a subcooled water spray, along with a cyclone separator mechanism intended for generating pure CO2. The investigation of the SEC...
-
Experimental investigation on straight and u-bend double tube heat exchanger with active and passive enhancement methods
PublikacjaAuthors in this work want to demonstrate the possibility to increase the heat transfer efficiency by using simple wire coil inserts to create turbulent flow in the boundary layer as well as air blowing into the annulus of the pipe. In the study, Wilson plot approach was applied in order to estimate heat transfer coefficients for all heat exchanger (HX) configurations. The study focuses on experimental values of heat transfer coefficient...
-
An advanced Thermal-FSI approach to flow heating/cooling
PublikacjaActually, two-way thermal-energy exchange between working fluid and solid material of a casing is a leading problem for modern – semi automatic – design techniques. Many questions should be solved, especially, the turbulent mode of thermal energy transport both in fluid and solid, should be re-examined and reformulated from the primary principles. In the present paper, a group of researchers from Energy Conversion Department of...
-
Magneto-thermal convection of low concentration nanofluids
PublikacjaThe main aim of this paper was to analyze possible utilization of the low concentration nanofluids and the magnetic field to enhance heat transfer. The studied fluids were based on water with an addition of copper particles (40-60 nm diameter). They belonged to the diamagnetic group of materials. As a first attempt to stated target the analysis of enclosure placed in the maximal value of square magnetic induction gradient was carried...
-
Optimizing CO2 Purification in a Negative CO2 Emission Power Plant
PublikacjaIn the pursuit of mitigating CO2 emissions, this study investigates the optimisation of CO2 purification within a Negative CO2 Emission Power Plant using a spray ejector condenser (SEC) coupled with a separator. The approach involves direct-contact condensation of vapour, primarily composed of an inert gas (CO2), facilitated by a subcooled liquid spray. A comprehensive analysis is presented, employing a numerical model to simulate...
-
Improvement of Thrust Bearing Calculation Considering the Convectional Heating within the Space between the Pads
PublikacjaA modern thrust bearing tool is used to estimate the behavior of tilting pad thrust bearings not only in the oil film between pad and rotating collar, but also in the space between the pads. The oil flow in the space significantly influences the oil film inlet temperature and the heating of pad and collar. For that reason, it is necessary to define an oil mixing model for the space between the pads. In the bearing tool, the solutions...
-
Experimental investigation of forced convection of water-Al2O3 nanofluids inside horizontal tubes,
PublikacjaIn this paper, forced convection of water–Al2O3 nanofluids inside horizontal copper tube is studied experimentally. Experiments were conducted for three, i.e. 0.1%, 1% and 5% nanoparticle mass concentrations under transition and turbulent flow regimes. Average heat transfer coefficients and pressure drop values were determined and compared to distilled water. Enhancement of heat transfer for lower nanoparticle concentration and...
-
Performance analyses of helical coil heat exchangers. The effect of external coil surface modification on heat exchanger effectiveness
PublikacjaThe shell and coil heat exchangers are commonly used in heating, ventilation, nuclear industry, process plant, heat recovery and air conditioning systems. This type of recuperators benefits from simple construction, the low value of pressure drops and high heat transfer. In helical coil,centrifugal force is acting on the moving fluid due to the curvature of thetube results in the development. It has been long recognized that the...
-
Experimental and Computational Fluid Dynamics Studies on Straight and U-Bend Double Tube Heat Exchangers with Active and Passive Enhancement Methods
PublikacjaIn this work, the authors wanted to demonstrate the possibility to increase the heat transfer efficiency by using simple wire coil inserts to create turbulent flow in the boundary layer as well as air blowing into the annulus of the pipe. Experimental investigations were carried out for four heat exchanger constructions, i.e., plain double tube, turbulized double tube, plain U-bend double tube, U-tube with turbulator, plain double...
-
Fluid Mechanics, L/L/E, DaPE, sem. 04, summer 21/22 (PG_00050282)
Kursy OnlineLECTURES Introduction and basic definitions. Properties of fluids. Models of fluids. Fluids in equilibrium. Determination of hydrostatic forces. Archimedes" law. Methods of fluid flow description. General motion of fluid. Deformation of fluid element. Vortex motion of fluid. Principles of conservation of mass, momentum and energy. Balance of entropy. Navier-Stokes equation. Bernoulli equation. Similarity of flow phenomena. Potential...
-
Numerical Modelling of Forced Convection of Nanofluids in Smooth, Round Tubes: A Review
PublikacjaA comprehensive review of published works dealing with numerical modelling of forced convection heat transfer and hydrodynamics of nanofluids is presented. Due to the extensive literature, the review is limited to straight, smooth, circular tubes, as this is the basic geometry in shell-and-tube exchangers. Works on numerical modelling of forced convection in tubes are presented chronologically in the first part of the article....
-
Experimental investigation of forced convection of water/EGAl2O3 nanofluids inside horizontal tube
PublikacjaIn this paper, forced convection of water/EG-Al2O3 nanofluids inside horizontal stainless steel tube is studied experimentally. As base fluid served water/EG mixture of two ratios (60:50 and 50:50). Nanoparticle mass concentrations was 0.1% or and 1%. Transition and turbulent flow regimes were tested. Average heat transfer coefficient and pressure drop values were determined for nanofluids and compared to base fluids. Deterioration...
-
Heat transfer intensification by jet impingement – numerical analysis using RANS approach
PublikacjaJet impingement is a method of the heat transfer enhancement applied in the engineering systems. The idea is to generate fast-flow fluid jet which impinge on the heated (or cooled) surface, causing significantly higher heat transfer rate. Although some flat surface jet impingement cases are described in the literature, the validated data is still limited. The reason is coming from the fact, that these flows are hydrodynamically...
-
CO2 capture using steam ejector condenser under electro hydrodynamic actuator with non-condensable gas and cyclone separator: A numerical study
PublikacjaThe concept for condensation of steam and CO2 separation in a negative CO2 emission gas power plant involves the utilization of a steam ejector condenser (SEC) for direct-contact condensation of vapor with inert gas (CO2) on a spray of subcooled liquid, integrated with a separator to produce pure CO2. Due to the increasing diffusion resistance and reduced convective heat transfer between the steam and subcooled water phases...
-
Numerical analysis of the ostiomeatal complex aeration using the CFD method
PublikacjaWe aimed to analyse ostiomeatal complex (OMC) aeration using the computational fluid dynamics (CFD) method of simulation based on human craniofacial computed tomography (CT) scans. The analysis was based on CT images of 2 patients: one with normal nose anatomy and one with nasal septal deviation (NSD). The Reynolds-Average Simulation approach and turbulence model based on linear eddy viscosity supplemented with the two-equation...
-
DO WE NEED NAVIER NUMBER? – FURTHER REMARKS AND COMPARISON WITH ANOTHER DIMENSIONLESS NUMBERS
PublikacjaThis paper presents a role of the Navier number (Na-dimensionless slip-length) in universal modelling of flow reported in micro- and nano-channels like: capillary biological flows, fuel cell systems, micro-electro-mechanical systems and nano-electro-mechanical systems. Similar to another bulk-like and surface-like dimensionless numbers, the Na number should be treated as a ratio of internal viscous to external viscous momentum...
-
Improvement of the thrust bearing calculation considering the convectional heating within the space between the pads
PublikacjaA modern thrust bearing calculation tool should consider not only the oil film between pad and rotating collar but also the space between the pads. The oil flow in the space has a significant influence on the oil film inlet temperature, the convectional cooling of pad and collar and should be included in the bearing calculation methods. The authors use a tool developed at Clausthal University of Technology in cooperation with the...
-
Effect of Simultaneous Valve Closures in Hydraulic Piping Systems
PublikacjaThe paper investigates wave interference (between pressure waves) occurring in simple hydraulic systems. Water hammer was induced by simultaneous closure of three valves located at the reservoirs of a “Y” type hydraulic system. Numerical simulations were carried out with the help of the freeware computer package Allievi enabling the reader to replicate results in a direct manner. The influence of the following quantities has been...
-
Investigations of the Working Process in a Dual-Fuel Low-Emission Combustion Chamber for an FPSO Gas Turbine Engine
PublikacjaThis investigation is devoted to an analysis of the working process in a dual-fuel low-emission combustion chamber for a floating vessel’s gas turbine. The low-emission gas turbine combustion chamber with partial pre-mixing of fuel and air inside the outer and inner radial-axial swirlers was chosen as the object of research. When modelling processes in a dual-flow low-emission gas turbine combustion chamber, a generalized method...
-
Navier number and transition to turbulence
PublikacjaThe motivation behind this article is to explain a role of the Navier number (Na -dimensionless slip-length) in prediction of closures for laminar to turbulent transition undergoing via eddies detachment from the slip layer in nano-cannals. Additionally the role of the Navier number Na in universal modeling of phenomenon of enhanced mass flow rate reported in micro- and nano-channels has been explained. The Na number should be...
-
Fluid Mechanics and Hydraulics EE Msc sem. I r.a. 22/23
Kursy OnlineBasic definitions. Physical properties of liquids. Forces acting on fluids. Hydrostatics - basic equations. Pressure on a flat and curved wall. Buoyancy. Archimedes' law. Balance of submerged bodies. The balance of floating bodies. Hydrodynamics. Hydrodynamic quantities. Continuity equation for the liquid stream. Bernoulli equation. Basic laws of hydrodynamics. Equation of mass behavior, preservation of the amount of motion, Bernoulli's...
-
Fluid Mechanics and Hydraulics EE Msc sem. I r.a. 23/24
Kursy OnlineBasic definitions. Physical properties of liquids. Forces acting on fluids. Hydrostatics - basic equations. Pressure on a flat and curved wall. Buoyancy. Archimedes' law. Balance of submerged bodies. The balance of floating bodies. Hydrodynamics. Hydrodynamic quantities. Continuity equation for the liquid stream. Bernoulli equation. Basic laws of hydrodynamics. Equation of mass behavior, preservation of the amount of motion, Bernoulli's...
-
CO2 capture through direct-contact condensation in a spray ejector condenser and T- junction separator
PublikacjaThe design principle underlying the steam condensation and CO2 purification in a gas power plant with a focus on reducing CO2 emissions encompasses the deployment of a spray ejector condenser (SEC) and separator. This innovative system facilitates direct-contact condensation of steam with non-condensable gas (CO2) by inter acting with a spray of subcooled water, seamlessly integrated with a T-junction separator mechanism aimed...
-
Wpływ wybranych parametrów środowiska na przebieg degradacji rur okładzinowych ze stali P110
PublikacjaMateriały używane na orurowanie odwiertów w poszukiwaniu i wydobyciu ropy i gazu poddawane są niekorzystnym warunkom eksploatacji takich jak: podwyższona temperatura, wysokie ciśnienie, turbulentny przepływ korozyjnych cieczy z zawieszonymi cząstkami stałymi. Jednym z gatunków stali używanych do produkcji rur okładzinowych jest stal P110 (za normą API 5CT) będąca stalą średnio-węglową, niskostopową o wysokiej wytrzymałości. Celem...
-
Suspended-sediment transport related to ice-cover conditions during cold and warm winters, Toudaoguai stretch of the Yellow River, Inner Mongolia, China
PublikacjaThe presence of winter ice in cold regions changes the water level, flow rate, velocity distribution, and other parameters of the river, which in turn affects the sediment concentration and channel evolution. Based on data obtained from Toudaoguai Hydrological Station from 1959 to 2021, this study examines the characteristics of the ice regime during cold and warm winters and the water and sediment transport processes along the...
-
Ocean mixed layer dynamics: high-resolution simulations of wind, wave and convective effects
Dane BadawczeThis dataset contains results of high-resolution numerical simulations of the ocean mixed layer (OML) forced by wind, waves and cooling from the atmosphere, i.e., under strongly turbulent, convective conditions. The goal is to provide detailed, three-dimensional information about OML circulation, turbulent kinetic energy, and temperature and salinity...