Wyszukiwarka
Filtry
wszystkich: 1383
wybranych: 1192
-
Katalog
Filtry wybranego katalogu
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: PRECISION MACHINING
-
MULTI-CRITERIA INVESTMENT DECISION SUPPORT MODEL USING FUZZY ANALYTIC HIERARCHY PROCESS (F-AHP) METHOD FOR POWER INDUSTRY
PublikacjaIn this paper, the comparative analysis of two wind farm construction projects was presented. This particular type of analysis is commonly applied before purchasing investment project being in a planning phase by a company interested in its development. Conduction of this type of analysis is prompted by the necessity to take into consideration the requirements of Polish legislation. Comparison of wind farm construction projects...
-
Worm Gear Drives with Improved Kinematic Accuracy
PublikacjaThis paper presents the fundamentals of the design and applications of new worm gear drive solutions, which enable the minimisation of backlash and are characterised by higher kinematic accuracy. Different types of worm surfaces are briefly outlined. Technological problems concerning the principles of achieving a high degree of precision in machining are also described. Special attention is paid to the shaping of conical helical...
-
The Use of Artificial Neural Networks and Decision Trees to Predict the Degree of Odor Nuisance of Post-Digestion Sludge in the Sewage Treatment Plant Process
PublikacjaThis paper presents the application of artificial neural networks and decision trees for the prediction of odor properties of post-fermentation sludge from a biological-mechanical wastewater treatment plant. The input parameters were concentrations of popular compounds present in the sludge, such as toluene, p-xylene, and p-cresol, and process parameters including the concentration of volatile fatty acids, pH, and alkalinity in...
-
The Weather as an Indicator for Decision-Making Support Systems Regarding the Control of Cutworms in Beets and Cereal Leaf Beetles in Cereals and Their Adoption in Farming Practice
Publikacja -
Does Mental Health Affect the Decision to Vaccinate Against SARS-CoV-2? A Cross-Sectional Nationwide Study Before the Vaccine Campaign
Publikacja -
On Decision-Making Strategies for Improved-Reliability Size Reduction of Microwave Passives: Intermittent Correction of Equality Constraints and Adaptive Handling of Inequality Constraints
PublikacjaDesign optimization of passive microwave components is an intricate process, especially if the primary objective is a reduction of the physical size of the structure. The latter has become an important design consideration for a growing number of modern applications (mobile communications, wearable/implantable devices, internet of things), where miniaturization is imperative due to a limited space allocated for the electronic circuitry....
-
Generative Process Planning with Reasoning based on Geometrical Product Specification
PublikacjaThe focus of this paper is on computer aided process planning for parts manufacture in systems of definite process capabilities, involving the use of multi-axis machining centers for parts shaping and grinding machines for finishing. It presents in particular a decision making scheme for setup determination as a part of generative process planning. The planning procedurę consists of two stages. The first stage is associated with...
-
Integrated production technology of cylindrical surfaces by turning and burnishing
PublikacjaThe method is based on a combination of previously used two separate operations namely machining and burnishing in a one complex operation implemented on a lathe.In the case of machining shafts and hydraulic cylinders of steel C45 is possible to obtain a surface roughness Ra=0,16 - 0,32 micrometers, dimensional accuracy class 7-8 according to ISO standards, and increase in the hardness of the surface up to 40%.
-
Analysis of the risk factors for perioperative morbidity after laparoscopic revisional bariatric procedures: results from the multicenter Polish Revision Obesity Surgery Study
Publikacja -
Reduction in Errors in Roughness Evaluation with an Accurate Definition of the S-L Surface
PublikacjaCharacterization of surface topography, roughly divided into measurement and data analysis, can be valuable in the process of validation of the tribological performance of machined parts. Surface topography, especially the roughness, can respond straightly to the machining process and, in some cases, is defined as a fingerprint of the manufacturing. When considering the high precision of surface topography studies, the definition...
-
Limiting distribution of the three-state semi-Markov model of technical state transitions of ship power plant machines and its applicability in operational decision-making.
PublikacjaThe article presents the three-state semi-Markov model of the process {W(t): t 0} of state transitions of a ship power plant machine, with the following interpretation of these states: s1 – state of full serviceability, s2 – state of partial serviceability, and s3 – state of unserviceability. These states are precisely defined for the ship main engine (ME). A hypothesis is proposed which explains the possibility of application...
-
Quality of Institutions for Knowledge-based Economy within New Institutional Economics Framework. Multiple Criteria Decision Analysis for European Countries in the Years 2000–2013
Publikacja -
Analysis of the Factors Contributing to Bariatric Success After Laparoscopic Redo Bariatric Procedures: Results from Multicenter Polish Revision Obesity Surgery Study (PROSS)
Publikacja -
Profile irregularities of turned surfaces as a result of machine tool interactions
PublikacjaThe paper describes the influence of the machining operation on a surface, which disturbs the projection of the tool profile in the form of its relative movements with respect to the object. The elements of the machine tool undergo constant wear during the machining process, it is therefore important to recognize the effects of their influence on the surface's irregularities. Amplitude-frequency analysis of lateral profiles has...
-
THE EFFECT OF ALTERNATIVE CUTTER PATHS ON FLATNESS DEVIATIONS IN THE FACE MILLING OF ALUMINUM PLATE PARTS
PublikacjaIn this paper the relationships between the alternative machining paths and flatness deviations of the aluminum plate part, were presented. The flatness tolerance of the main surface of the plate part has crucial meaning due to the assembly requirement of piezoelectric elements on the radiator. The aluminum bodies under investigation are the base part of the radiators with crimped feathers for the train industry. The surface of...
-
PUBLIC SPACES FOR LOCAL LIFE / Shared values in diversified urban communities as a foundation for participatory provision of local public spaces, 23-27 May 2017, Ljubljana Slovenia
PublikacjaThe Urban Planning Institute of the Republic of Slovenia (UIRS) and partners hosted a 5-day international event addressing participatory planning of local urban public space in socially, economically and ethnically diverse communities. The event was structured in three interrelated activities: a seminar, a workshop and a field-trip. Special emphasis was given to the means of revealing shared values that local inhabitants and other...
-
Allocation of tools to machines in a flexible machining cell. W: Computerintegrated manufacturing. Advanced design and management. Ed.: B. Skołud, D. Krenczyk. Warszawa: Wydaw. Nauk.-Tech.**2003 s. 486-493, 5 rys. 2 tabl.bibliogr. 10 poz. Przydział narzędzi do obrabiarek w elastycznym gnieździe obróbkowym.
PublikacjaPrzedstawiono zagadnienia modelowania i analizy przepływu narzędzi w wielo-maszynowym elastycznym gnieździe, zorientowanym na wytwarzanie przedmiotów klasy korpus. Zaproponowano oryginalną metodę i algorytmy współbieżnego sze-regowania zadań produkcyjnych i przydziału narzędzi w warunkach ograniczono-ści zasobów systemu. Wybrane strategie przydziału operacji technologicznych i adekwatnych zestawów narzędziowych poddano analizie...
-
Na efektywność wpływa sposób przetarcia. Seminarium Obróbki Drewna w Szwecji
PublikacjaW artykule przedstawiono relację z 20th International Wood Machining Seminar, które odbyło się w Skelleftea w Szwecji.
-
The Design Development of the Sliding Table Saw Towards Improving Its Dynamic Properties
PublikacjaCutting wood with circular saws is a popular machining operation in the woodworking and furniture industries. In the latter sliding table saws (panel saws) are commonly used for cutting of medium density fiberboards (MDF), high density fiberboards (HDF), laminate veneer lumber (LVL), plywood and chipboards of different structures. The most demanded requirements for machine tools are accuracy and precision, which mainly depend on...
-
Effect of Thermal Treatment of Birch Wood by Saturated Water Vapor on Granulometric Composition of Chips from Sawing and Milling Processes from the Point of View of Its Processing to Composites
PublikacjaThe goal of this work is to investigate the impact of thermal modification of birch wood with saturated steam on the particle size distribution of the sawing and milling process. Birch wood (Betula pendula Roth) is an excellent source to produce plywood boards. Wastes from mechanical processing of birch wood are suitable to produce composite materials. Granulometric analyses of chips from sawing processes on the PRW 15M frame saw,...
-
Optimizing Construction Engineering Management Using Metaheuristic Methods and Bayesian Networks
PublikacjaThe construction of buildings invariably involves time and costs, and disruptions impact ongoing construction projects. Crisis situations in management strategies, structural confusion, and finan-cial miscalculations often arise due to misguided decision-making. This article proposes a method that combines the learning of Bayesian Networks and heuristic techniques to optimize deci-sion-making processes in construction scheduling....
-
NUMERICAL SIMULATIONS OF HONING PROCESS OF THIN WALL CYLINDER LINERS, WITH CONSTANT AND WITH VARIABLE THICKNESS OF WALL OF HONED PARTS
PublikacjaNumerical simulations of honing process of thin-wall cylinder liners, with constant and with variable thickness of the wall of honed workpieces can improve and can help to conduct the experimental research of honing process and can improve the honing process. A very valuable research assumption, before performing the numerical analysis of computer simulation of honing process, is the measurement of the real geometry of the honing...
-
The Proposition of an Automated Honing Cell with Advanced Monitoring
PublikacjaHoning of holes allows for small shape deviation and a low value of a roughness profile parameter, e.g., Ra parameter. The honing process heats the workpiece and raises its temperature. The increase in temperature causes thermal deformations of the honed holes. The article proposes the construction of a honing cell, containing in addition to CNC honing machine: thermographic camera, sound intensity meter, and software for collecting...
-
Przydział narzędzi obróbkowych a efektywność szeregowania zadań produkcyjnych
PublikacjaThe paper addresses issues concerning the analysis of tool flow within a multi-machine machining cell, designated to small batch manufacturing a definite spectrum of prismatic parts. The approach utilises a method for job and tool allocation to work centres with limited number of machines and capacity of tool resources, based on the analysis of formalised relations: job - tool sets required. Selected allocation strategies are considered...
-
The use of Preston equation to determine material removal during lap-grinding with electroplated CBN tools
PublikacjaGrinding executed in a lapping configuration is an alternative finishing process benefiting from both grinding and free-abrasive machining, while minimizing the heat effect impact. Electroplated tools can be effectively used in different abrasive processes, including high-speed grinding, however, the assessment of machining performance over time is a key factor in their correct use to achieve satisfactory technological results....
-
VIBRATION SURVEILLANCE DURING MILLING OF FLEXIBLE DETAILS WITH A USE OF THE ACTIVE OPTIMAL CONTROL
PublikacjaThe main goal of modern machining operations is to achieve increasingly better performance. High Speed Machining and/or High Performance Cutting, despite a lot of advantages, have also some drawbacks, for example, a possibility of losing stability and development of self-excited chatter vibration. This paper presents an approach of vibration surveillance during high speed milling with a use of active optimal control. Non-stationary...
-
Influence and development of new kinematic systems in flat surface lapping
PublikacjaThe face grinding and lapping technology is widely used in the field of the precise and ultraprecise manufacturing. It has become an indispensable technology in the manufacture of many parts. An absence of material restrictions allows machining both metal and non-metallic materials, including technical ceramics [1]. Nowadays there are mainly two kinematic systems in lapping machines [2]. The machining plane-parallel surfaces is...
-
The Influence of Workpiece Hardness on Plate Temperature during One Side Lapping
PublikacjaLapping leads to a surface with low roughness and high precision. Because of required parts accuracy tool flatness is the key to the successful machining. To avoid its excessive thermal expansion, plate temperature research was taken. The goal was to determine the correlation between the basic lapping conditions and wheel temperature. In work Bulsara et al. authors developed model to estimate the maximum and average temperature...
-
Detailed experimental investigations on frictional pressure drop of R134a during flow boiling in 5 mm diameter channel: The influence of acceleration pressure drop component =Études expérimentales détaillées sur la chute de pression frictionnelle du R134a lors de l'ébullition en écoulement dans un canal de 5 mm de diamètre : influence de la composante d'accélération de la chute de pression
PublikacjaThis article presents detailed two-phase diabatic pressure drop data for refrigerant R134a at a saturation pressure of 5.5 bar corresponding to the saturation temperature of 19.4 °C. Study cases have been set for a mass flux varying from 100 to 500 kg m−2 s−1. The obtained data are used as a validation of the void fraction literature models, a set of graphs shows comparisons, for a representative set of experimental conditions,...
-
A pilot study to assess manufacturing processes using selected point measures of vibroacoustic signals generated on a multitasking machine
PublikacjaThe article presents the method for the evaluation of selected manufacturing processes using the analysis of vibration and sound signals. This method is based on the use of sensors installed outside the machining zone, allowing to be used quickly and reliably in real production conditions. The article contains a developed measurement methodology based on the specific location of microphones and vibration transducers mounted on...
-
Circular saw vibrations or dynamics of the spindle
PublikacjaSawing of wood with circular saws is a typical example of cutting with multi-blade tools. In that kind of cutting, theposition accuracy of following tool blades is a crucial factor which affects the cutting process and machining final effects.Position tooth errors may cause deterioration in cutting conditions, changes in loads of individual teeth and the tool as a whole,and also a decrease in accuracy and surface quality after...
-
Influence of Honing Parameters on the Quality of the Machined Parts and Innovations in Honing Processes
PublikacjaThe article presents a literature review dealing with the effect of the honing parameters on the quality of the machined parts, as well as with the recent innovations in honing processes. First, an overview about the honing and the plateau-honing processes is presented, considering the main parameters that can be varied during machining. Then, the influence of the honing parameters on surface finish, shape deviation and material...
-
Microgrinding of flat surfaces on single-disc lapping machine
PublikacjaW pracy przedstawiono możliwości zastosowania specjalnych narzędzi do mikroszlifowania na docierarce jednotarczowej. Jedno z zastosowanych narzędzi posiada warstwę ścierniwa diamentowego (D64) nałożoną metodą galwaniczną. Drugie przetestowane narzędzie zbudowane zostało z diamentowych pastylek ściernych (D3/2). Przedstawiono analizę kinematyczną i wyniki ubytku materiałowego oraz osiągnięte parametry chropowatości.
-
Technological Problems in Lapping on Flat Surfaces of Ceramic Parts
PublikacjaThis paper will present the results of research on single-disc lapping of flat surfaces of small ceramic elements. Machining with the use of different tools such as metallic, two-metallic and abrasive-metallic will be analyzed. The basics and techniques of reinforcement of laps will be discussed. The results of the influence of parameters on the surface quality of ceramic conponents (sealing) for three treatments on lapping machines...
-
Surface Texture Analysis of Hardened Shafts after Ceramic Ball Burnishing
PublikacjaThis article represents the results of testing the surface condition of shafts manufactured by the burnishing process. The shafts with a hardness of approximately 62 HRC (Rockwell C). were burnished with a ceramic ball (Si3N4), where the force range was controlled by the means of a hydraulic system. The machining process consisted of hard turning shafts with cubic boron nitride (CBN) inserts, followed by burnishing with the use...
-
Optimal spindle speed determination for vibration reduction during ball-end milling of flexible details
PublikacjaIn the paper a method of optimal spindle speed determination for vibration reduction during ball-end milling of flexible details is proposed. In order to reduce vibration level, an original procedure of the spindle speed optimisation, based on the Liao–Young criterion, is suggested. As the result, an optimal, constant spindle speed value is determined. For this purpose, on-stationary computational model of machining process is...
-
Production activity control in a flexible machining cell considering part measuring condition. W: Computer integrated manufacturing. Advanced design and management. Ed.: B. Skołud, D. Krenczyk. Warszawa: Wydaw. Nauk.-Tech. **2003 s. 494-501, 6 rys. 1 tabl. bibliogr. 9 poz. Sterowanie procesu produkcyjnego w elastycznym gnieździe obróbkowym z uwzg- lędnieniem funkcji kontroli wytwarzanych przedmiotów.
PublikacjaPrzedstawiono modele struktur organizacyjnych przebiegu procesu organizacyj-nego w rzeczywistym zrobotyzowanym elastycznym gnieździe obróbki (EGO) z udziałem współrzędnościowej maszyny pomiarowej CNC. Badano eksperymentalnie występujące współzależności pomiędzy analizowanymi planami kontroli przed-miotów wytwarzanych i strategiami szeregowania operacji procesu technologi-cznego obróbki, z wykorzystaniem zintegrowanych modeli...
-
Wear of Electroplated Tools Used for Flat Grinding of Ceramics
PublikacjaTwo methods for the abrasive properties evaluation, based on the image processing, are presented in the paper. Image processing analysis was developed to evaluate quickly the abrasive properties as the tool wears down. The coefficient based on the image brightness was calculated and additional analysis was based on the number of grains located on the active surface of the tool before and after machining. The active surfaces of...
-
Surface Structure of Components Created by Stereolitography
PublikacjaStereolithography is an additive rapid prototyping method. This method is based on the principle of solidifying a liquid photopolymer (resin) by laser radiation. Models obtained with this method are characterized by a specific surface structure called “stairstep effect”. It causes that, the surface should be processed by additional finishing (postprocessing). To minimize the additional machining process, the model should be set...
-
Design of precise control systems of industrial plants
PublikacjaA method for developing precision control systems in industry has been created based on a set of models that take into account the nonlinearity of the reactor model, the nonlinearities of the hydrodynamic regime and the accuracy of the control elements, the nonlinear characteristics and accuracy of the actuators, and the precision of the sensors used. A multidimensional precision control system has been developed for a continuous...
-
Multi-response optimization on the effect of wet and eco-friendly cryogenic turning of D2 steel using Taguchi-based grey relational analysis
PublikacjaMaterial removal processes, including turning and milling, are still commonly used operations for manufacturing most of mechanical components in modern industry. Apart from the cutting parameters, the cooling method has the great impact on the technological efects and, above all, on the environmental friendliness of production. In this study, multi-response optimization on the efect of wet and cryogenic machining is performed during...
-
Influence of finishing colour on the efficiency of automated production line for wooden doors
PublikacjaPorta KMI Poland S.A. company has implemented a fully automated intelligent technological line TechnoPORTA for customized mass-production of technical door leaves. Each door leaf is provided with a unique QR code. It allows the line modules to individually adjust the machining parameters to the currently processed element according to the IT controlling system. Before en-tering the TechnoPorta line, the door leaves are not sorted,...
-
Thermal and technological aspects of double face grinding of Al2O3 ceramic materials
PublikacjaDouble face grinding with planetary kinematics is a process to manufacture workpieces with plan parallel functional surfaces, such as bearing rings or sealing shims. In order to increase the economic efficiency of this process, it has to be advanced permanently. The temperature in the contact zone of most grinding processes has a huge influence on the process efficiency and the workpiece qualities. In contrast to most grinding...
-
Distribution of roughness and waviness components of turned surface profiles
PublikacjaThe paper presents a spectral formulation of surface profile irregularity in a wideband frequency range for roughness, waviness and shape components along the measured length. A unique distribution of roughness and waviness components is proposed, according to the nature of their origination in the course of machining with tools of defined cutting edge, as distinct from standard filtration in measurements of surface irregularities....
-
Influence of Flat Lapping Kinematics on Machinability of Ceramics
PublikacjaNew tools for flat grinding of ceramics are presented in the paper. Electroplated CBN tools (B64 and B107) were used in a modified single-disc lapping machine configuration. The results from experiments, such as the material removal rate and surface roughness parameters are presented and analyzed. Numerical simulations, based on the model for the shape error and tool wear estimation in machining with flat lapping kinematics, are...
-
Research on the wear evenness of the tool in flat lapping
PublikacjaIn this paper, the dimensionless distribution of the material removal stock and the trajectories of abrasive grains cutting in single-sided lapping process are presented. They were numerically simulated based on the tribological model and kinematics equations. It can be observed that the trajectories geometry of single abrasive as well the velocities have a great influence on the final geometrical deviation. During machining, the...
-
Optimization of clamping stiffness during milling of high-dimensional structures with the use of techniques of experiment – aided virtual prototyping
PublikacjaThe subject of this paper is a method of searching for conditions of minimizing the vibration level of a tool-high dimensional flexible workpiece, at unchangeable technological parameters of the machining process. It depends on repeatable change of the values of the stiffness coefficients as soon as an optimal vibration state of the workpiece approaches. There are assessed the values of dominant ”peaks” in the frequency spectra...
-
A Method and Device for 3D Recognition of Cutting Edge Micro Geometry
PublikacjaA very useful method was successfully applied in the investigation of tools for machining wood and wood based composites. It allows scanning of the cutting edge micro geometry in three dimensions and reproducing it in a virtual space as a 3D surface. The application of the method opens new possibilities of studying tool wear by scanning, including the calculation of volume loss and other analysis of tool wedge geometry along and...
-
Selected Aspects of 3D Printing for Emergency Replacement of Structural Elements
PublikacjaThe paper presents a synthetic characterization of modern methods of manufacturing or regenerating machine elements. Considered methods are machining and additive methods, in particular 3D printing in the FDM/FFF technique. For the study, the authors made samples of the holder bracket using selected methods. Samples made by machining operations, 3D printing with various filling were tested. The paper contains a technical and economic...
-
Customization of UWB 3D-RTLS Based on the New Uncertainty Model of the AoA Ranging Technique
PublikacjaThe increased potential and effectiveness of Real-time Locating Systems (RTLSs) substantially influence their application spectrum. They are widely used, inter alia, in the industrial sector, healthcare, home care, and in logistic and security applications. The research aims to develop an analytical method to customize UWB-based RTLS, in order to improve their localization performance in terms of accuracy and precision. The analytical...