Wyniki wyszukiwania dla: HEMODYNAMICS
-
Rheology of polymer blends
PublikacjaPolymer blends are physical mixtures of two or more homopolymers or copolymers. This type of materials have wide spectrum of technological applications, and their properties are influenced, e.g., by the properties of single components and morphology of final material. The rheology of polymer blends is connected with the processing of polymer blends and is influenced by thermodynamics, morphology, and their evolution during testing....
-
THE INFLUENCE OF THE URBAN DESIGN ON THE AIR EXCHANGE IN CITIES. SELECTED PROBLEMS IN POLISH REALITY
PublikacjaThe progress of the architecture and urbanism raises problems requiring interdisciplinary research conducted with the use of advanced experimental techniques and computer simulation. The fields of this research include aerodynamics, especially in intensively developed area of Environmental Wind Engineering (EWE). Aerodynamic phenomena occurring around buildings have a significant impact on the quality of the climate in the cities....
-
Water uptake and energetics of the formation of barium zirconate based multicomponent oxides
PublikacjaA group of multi-component oxides based on BaZrO3 have been prepared using a solid-state reaction method and examined in terms of their water uptake and thermodynamics of formation. Depending on the type and amount of acceptor substitution, the synthesized compounds exhibit various proton defect concentrations, reaching up to 0.2 mol/mol for a compound containing 10 different elements in the B-sublattice, where 50% of them are...
-
Proposal of New Tracer Concentration Model in Lung PCT Study Comparison with Commonly Used Gamma-variate Model
PublikacjaPerfusion computed tomography (pCT) is one of the methods that enable non-invasive imaging of the hemodynamics of organs and tissues. On the basis of pCT measurements, perfusion parameters such as blood flow (BF), blood volume (BV), mean transit time (MTT) and permeability surface (PS) are calculated and then used for quantitative evaluation of the tissue condition. To calculate perfusion parameters it is necessary to approximate...
-
Kinetic analysis of the stage for a high speed steam turbine
PublikacjaThis article analyzes possibilites of resonances within a control stage for a high speed steam turbine. This stage hase been based on assembling of a single blade to a rotating disk and increasing of rigidity of the system by using of a bandage. In the analysis will be nd a possiblity of resonance frequency, and mistuning by showing safety working ranges. The calculations have bean used the3D modal and harmonic analysis by the...
-
Quantum Coherence as a Resource
PublikacjaThe coherent superposition of states, in combination with the quantization of observables, represents one of the most fundamental features that mark the departure of quantum mechanics from the classical realm. Quantum coherence in many-body systems embodies the essence of entanglement and is an essential ingredient for a plethora of physical phenomena in quantum optics, quantum information, solid state physics, and nanoscale thermodynamics....
-
Dynamics of Chains as a Tool to Study Thermomechanical Properties of Proteins.
PublikacjaPolymer dynamics can be formulated on different levels of detail. One approach eliminates microscopic degrees of freedom and a polymer molecule is represented by a simplified structure—a chain. In the simplest case monomers of ideal chain have fixed length, and their orientation is independent of the orientations and positions of neighbouring monomers. This is reason that two monomers can co-exist at the same place. Ideal chain...
-
ANALYSIS OF WIND CONDITIONS AROUND A BUILDING DEVELOPMENT AS A PART OF ITS FORM DESIGNING PROCESS, A CASE STUDY
PublikacjaAerodynamic phenomena that occurs around building developments exert a significant impact on the quality of climate in cities. Environmental wind engineering is a dynamically developing field of knowledge that offers a chance to study and, in consequence, regulates the air flow around buildings and complexes of building developments. The following paper discusses the issue of wind conditions that may be experienced on pedestrian...
-
Analiza i ocena poprawności działania węzła tarcia w aspekcie II zasady termodynamiki
PublikacjaW artykule przedstawiono autorską metodę sprawdzania poprawności działania węzła tarcia traktowanego jako układ tribologiczny w aspekcie II zasady termo-dynamiki na podstawie analizy i oceny wyników badań laboratoryjnych wykonanych na stanowisku badawczym. Jako stanowisko wykorzystany został zmodyfikowany węzeł tarcia aparatu czterokulowego T-02. Zaprezentowano algorytm, według którego zostały wykonane badania empiryczne. Wykazano,...
-
Assessment of the impact of jet impingement technique on the energy efficiency of air-cooled BIPV/T roof tile
PublikacjaThe paper concerns a numerical analysis of cooling of the hybrid photovoltaic (PV) modules dedicated to Building-Integrated Photovoltaic/Thermal (BIPV/T) systems. Attention was focused on the photovoltaic roof tiles, using a jet impingement technique, in which the intensification of heat transfer is ensured by streams of air hitting the heat exchange partition. A series of numerical simulations were carried out to assess an influence...
-
New empirical correlations for the viscosity of selected organic phase change materials
PublikacjaAlthough there are many methods and instruments for measuring viscosity, it is still difficult to determine a reliable value of the dynamic viscosity of complex chemicals such as paraffins and fatty acids. This is due to the complex and heterogeneous structure of these compounds in the case of commercial products. On the other hand, the measuring instrument should be selected very carefully, including its measuring principle and...
-
Formation of bubbles from a single nucleation site.
PublikacjaPrzedstawiono wyniki systematycznych badań eksperymentalnych wrzenia wody destylowanej i metanolu z pojedynczego, sztucznego centrum nukleacji. Jako centra nukleacji służyły otwory wywiercone na czołowej powierzchni miedzianego pręta. Średnice otworów wynosiły: 0.25 mm, 0.60 mm oraz 1.0 mm. Do pomiaru częstotliwości odrywania się pęcherzyków zastosowano układ laser diodowy-fotodioda. Sygnał z fotodiody był rejestrowany za...
-
Increase of power and efficiency of the 900 MW supercritical power plant through incorporation of the ORC
PublikacjaThe objective of the paper is to analyse thermodynamical and operational parameters of the supercritical power plant with reference conditions as well as following the introduction of the hybrid system incorporating ORC. In ORC the upper heat source is a stream of hot water from the system of heat recovery having temperature of 90 °C, which is additionally aided by heat from the bleeds of the steam turbine. Thermodynamical analysis...
-
Revalorization of the Szewalski binary vapour cycle
PublikacjaThe aim of the paper is to revalorizate of the Szewalski binary vapour cycle by analysing thermodynamical and operational parameters of this cycle. This was carried by accessible numerical CFM (Computational Flow Mechanics) codes type, by step-by-step modeling of separates apparatus. The binary vapour cycle is providing steam as the working fluid in the high temperature part of the cycle, while another fluid - a low boiling point...
-
Investigation of the influence of capilary effect on operation of the loop heat pipe
PublikacjaIn the paper presented are studies on the inestigation of the capillary forces effect inducted in the porous structure of a loop heat pipe using water and ethanol ad test fluids. The potential application of such effects is for example in the evaporator of the domestic micro-CHP unit, where the reduction of pumping power could be obtained. Preliminary analysis of the results indicates water as having the best potential for developing...
-
Comparitive study of heat transfer and pressure drop during flow boiling and flow condensation in minichannels
PublikacjaIn the paper a method developed earlier by authors is applied to calculations of pressure drop and heat transfer coefficient for flow boiling and also flow condensation for some recent data collected from literature for such fluids as R404a, R600a, R290, R32,R134a, R1234yf and other. The modification of interface shear stresses between flow boiling and flow condensation in annular flow structure are considered through incorporation...
-
Pool boiling of nanofluids on rough and porous coated tubes: experimental and correlation
PublikacjaThe paper deals with pool boiling of water-Al2O3 and water- Cu nanofluids on rough and porous coated horizontal tubes. Commercially available stainless steel tubes having 10 mm outside diameter and 0.6 mm wall thickness were used to fabricate the test heater. The tube surface was roughed with emery paper 360 or polished with abrasive compound. Aluminium porous coatings of 0.15 mm thick with porosity of about 40% were produced by...
-
Thermal and economic investigation of straight and U-bend double tube heat exchanger with coiled wire turbulator
PublikacjaExperimental research has been carried out for four individual heat exchanger constructions, i.e., plain double tube, turbulized double tube, plain U-bend and U-bend with turbulator. Tests were made for the water-water system. The study covered a wide measuring range, i.e., Re = 800–9000 – on the shell side, for a constant cold water temperature of 9 ◦C and hot water of 50 ◦C. The heat exchangers were made from copper tubes with...
-
Optimisation of turbine shaft heating process under steam turbine run-up conditions
PublikacjaAn important operational task for thermal turbines during run-up and run-down is to keep the stresses in the structural elements at a right level. This applies not only to their instantaneous values, but also to the impact of them on the engine lifetime. The turbine shaft is a particularly important element. The distribution of stresses depends on geometric characteristics of the shaft and its specific locations. This means a groove manufactured...
-
Computational fluid dynamics simulation of heat transfer from densely packed gold nanoparticles to isotropic media
PublikacjaThis work aims to determine and compare heat generation and propagation of densely packed gold nanoparticles (Au NPs) induced by a resonant laser beam (532 nm) according to the Mie theory. The heat flux propagation is transferred into the materials, which here are: silica glass; soda-lime-silica glass; borosilicate glass; polymethyl methacrylate (PMMA); polycarbonate (PC); and polydimetylosiloxane (PDMS). This analysis aims to...
-
Performance of cryogenic oxygen production unit with exhaust gas bleed for sewage sludge gasification and different oxygen purities
PublikacjaThe paper presents a thermodynamic analysis of the integration of a cryogenic air separation unit into a negative CO2 emission gas power plant. The power cycle utilizes sewage sludge as fuel so this system fits into the innovative idea of bioenergy with carbon capture and storage. A cryogenic air separation unit integrated with the power plant was simulated in professional plant engineering and thermodynamic process analysis software....
-
Challenges in operating and testing loop heat pipes in 500–700 K temperature ranges
PublikacjaThe potential applications of loop heat pipes (LHPs) are the nuclear power space systems, fuel cell thermal management systems, waste heat recovery systems, medium temperature electronic systems, medium temperature military systems, among others. Such applications usually operate in temperature ranges between 500–700 K, hence it is necessary to develop an LHP system that will meet this requirement. Such a thermal management device...
-
Experimental investigation of domestic micro-CHP based on the gas boiler fitted with ORC module
PublikacjaThe results of investigations conducted on the prototype of vapour driven micro-CHP unit integrated with a gas boiler are presented. The system enables cogeneration of heat and electric energy to cover the energy demand of household. The idea of such system is to produce electricity for own demand or for selling it to the electric grid – in such situation the system user will became the prosumer. A typical commercial gas boiler,...
-
Optimal boiling temperature for ORC installation
PublikacjaW pracy przedstawiono oryinalne kryterium wyznaczania optymalnej temperatury odparowania czynnika w obiegu ORC w postaci równań analitycznych. Pokazano przykład obliczeniowy na bazie R134a, wody i etanolu.
-
Thermal-hydraulic issues of flow boiling and condensation in organic Rankine cycle heat exchangers
PublikacjaW pracy przedstawiono szereg zagadnień cieplno-przepływowych podczas wrzenia i kondensacji w przepływie w wymiennikach ciepła obiegu ORC. Uwzględniono przemiany fazowe. Analizowano zagadnienia stabilności pracy wymienników oraz ich dynamikę
-
Heat transfer and pressure drop characteristics of the silicone-based plate heat exchanger
PublikacjaThe paper presents an experimental investigation of a silicone based heat exchanger, with passive heat transfer intensification by means of surface enhancement. The main objective of this paper was to experimentally investigate the performance of a heat exchanger module with the enhanced surface. Heat transfer in the test section has been examined and described with precise measurements of thermal and flow conditions. Reported...
-
Analysis of start energy of Stirling engine type alpha
PublikacjaThe Stirling engine type alpha is composed of two cylinders (expansion space E and compression space C), regenerator that forms the space between the cylinders and the buffer space (under the pistons). Before the start-up and as a result of long-term operation, the average pressure in the working space (above the pistons) and in the buffer space is the same. However, in the initial phase of operation, the average pressure in the...
-
Design and computational fluid dynamics analysis of the last stage of innovative gas-steam turbine
PublikacjaResearch regarding blade design and analysis of flow has been attracting interest for over a century. Meanwhile new concepts and design approaches were created and improved. Advancements in information technologies allowed to introduce computational fluid dynamics and computational flow mechanics. Currently a combination of mentioned methods is used for the design of turbine blades. These methods enabled us to improve flow efficiency...
-
Modeling of the internal combustion engine cooling system
PublikacjaThe article concerns computer modelling of processes in cooling systems of internal combustion engines. Modelling objectives and existing commercial programs are presented. It also describes Author’s own method of binding graphs used to describe phenomena in the cooling system of a spark ignition engine. The own model has been verified by tests on the engine dynamometer. An example of using a commercial program for experimental...
-
Hydraulic resistance analyses of selected elements of the prototype Stirling engine
PublikacjaThe paper presents the results of simulation tests of hydraulic resistance and temperature distribution of the prototype Stirling alpha engine supplied with waste heat. The following elements were analyzed: heater, regenerator and cooler. The engine uses compressed air as a working gas. Analyses were carried out for three working pressure values and different engine speeds. The work was carried out in order to optimize the configuration...
-
Mathematical modeling of hydrogen production performance in thermocatalytic reactor based on the intermetallic phase of Ni3Al
PublikacjaThe main goal of the following work is to adjust mathematical modelling for mass transfer, to specific conditions resulting from presence of chemical surface reactions in the flow of the mixture consisting of helium and methanol. The thermocatalytic devices used for decomposition of organic compounds incorporate microchannels coupled at the ends and heated to 500 oC at the walls regions. The results of the experiment were compared...
-
Experimental and theoretical study of dryout in annular flow in small diameter channels
PublikacjaW pracy zaprezentowano badania eksperymentalne kryzysu wrzenia II rodzaju w kanałach o małej średnicy. Badania prowadzone były w rurach pionowych o średnicy 1.15 i 2.3 mm, w których badanym czynnikiem były płyny niskowrzące, takie jak SES36 i R123. W badaniach zastosowano nowoczesne techniki pomiarowe do określania lokalizacji kryzysu wrzenia na ściance kanału, np. kamerę termowizyjną. Na podstawie pozyskanych punktów eksperymentalnych...
-
Cogenerative micro power plants - a new direction for development of power engineering?
PublikacjaW pracy przedstawiono rozważania dotyczące perspektywy mikrosiłowni domowych w gospodarce rozproszonej. Przedstawiono oryginalne kryterium doboru czynnika roboczego w mikrosiłowni oraz przedstawiono sprawności cieplne i egzergetyczne obiegów Clausiusa-Rankina realizujących pracę mikrosiłowni.
-
A study of flow boiling heat transfer in minichannels
PublikacjaW pracy przedstawiono badania eksperymentalne wrzenia w przepływie w minikanale o średnicy wewnętrznej 2.3mm i długości 38cm. Uzyskano rozłady temperatury wzdłuż ścianki kanału oraz lokalne współczynniki przejmowania ciepła. Dane skorelowano z korelacją półempiryczną uzyskując zadowalającą zgodność.
-
Comparative study of selected fluids for use in supercritical Organic Ranking Cycles
PublikacjaIn view of increasing interest in improving energy efficiency of energy conversion devices, there is an increasing requirement of combined production of heat and electricity as well as demand for increased implementation of renewable energy resources. The micro cogenerative units utilizing the Organic Rankine Cycle are focusing the attention of many research centres around the world. In the present paper calculations of ORC cycles...
-
Dryout in annular flow - theoretical analysis
PublikacjaW pracy zaprezentowano model kryzysu wrzenia w przepływie pierścieniowym, obowiązujący dla wysokich wartości stopnia suchości i stanowiący modyfikację wcześniejszej wersji modelu zaproponowanego przez Sedlera i Mikielewicza. Model ten uwzględnia bilans masy w filmie cieczowym i bilans masy dla kropel cieczy w rdzeniu przepływu oraz zawiera dodatkowy człon odpowiedzialny za odparowanie filmu na ściance kanału. Rozwiązanie układu...
-
Utilisation of bleed steam heat to increase the upper heat source temperature in low-temperature ORC
PublikacjaW pracy przedstawiono możliwość dogrzewu obiegu ORC za pomocą pary upustowej.
-
Comparative study of flow condensation in conventional and small diameter tubes
PublikacjaFlow boiling and flow condensation are often regarded as two opposite or symetrical phenomena. Their description however with a single correlation has yet to be suggested.In the case of flow boiling in minichannels there is mostly encountered the annular flow structure, where the buble generetion is not present. Similar picture holds for the case of inside tube condensation, where annular flow structure predominates. In such case...
-
Experiences from operation of different expansion devices for application in domestic micro CHP
PublikacjaW pracy opisano doświadczenia zdobyte podczas badań trzech różnych urządzeń ekspansyjnych, możliwych do zaimplementowania w mikrosiłowni CHP. Przebadano ekspander wykonany na bazie sprężarki spiralnej oraz dwojakiego rodzaju silniki pneumatyczne. Wykazano "wyższość" maszyn pneumatycznych nad ekspanderem typu scroll, uzyskując sprawności wewnętrzne w zakresie 61-82%. Dodatkowo, mniejsza objętość i masa urządzeń pneumatycznych stanowi...
-
Determination of the thermal conductivity of material dividing the metallic core elements of the bi-calorimeter using modified theory
PublikacjaW pracy przedstawiono zmodyfikowaną teorię bikalorymetru z dzielonym metalowym rdzeniem. Pomiędzy dwiema częściami rdzenia umieszczano próbki badanego ciała stałego lub gazu. Ogrzewano jedną stronę rdzenia. Mierzono temperaturę obu części rdzenia w funkcji czasu. Uzyskane wyniki umożliwiły wyznaczenie różnicy temperatur i strumienia ciepła, przepływającego przez próbkę. Z zastosowaniem prawa Fouriera obliczano współczynnik przewodności...
-
Improved model of void fraction distribution in two-phase flow in the boundary layer
PublikacjaPraca skupiona jest na eksperymentalnej weryfikacji sił działających na pęcherzyk gazowy przepływający wzdłuż ścianki kanału, a następnie implementacji uzyskanych wyników do zaproponowanego wczesniej przez jednego z współautorów modelu rozkładu stopnia zapełnienia w warstwie przyściennej przepływu dwufazowego. Podczas badań pęcherzyk modelowany był sztywną kulą podwieszoną na strunie. Autorzy przekonują, że pokazany model dobrze...
-
A semi-empirical method for calculation of heat transfer coefficient in flow boiling for conventional tubes and minichannels
PublikacjaW pracy przedstawiono zagadnienia które należy uwzględnić podczas modelowania wymiany ciepła z wrzeniem w przepływie w kanałach o małej średnicy. Uzyskano dobrą zgodność z wynikami badań eksperymentalnych.
-
EFFECT OF NANOFLUID CONCENTRATION ON TWO-PHASE THERMOSYPHON HEAT EXCHANGER PERFORMANCE
PublikacjaAn approach – relaying on application of nanofluid as a working fluid, to improve performance of the two-phase thermosyphon heat exchanger (TPTHEx) has been proposed. The prototype heat exchanger consists of two horizontal cylindrical vessels connected by two risers and a downcomer. Tube bundles placed in the lower and upper cylinders work as an evaporator and a condenser, respectively. Distilled water and nanofluid water-Al2O3...
-
Prediction of flow boiling heat transfer coefficient for carbon dioxide in minichannels and conventional channels
PublikacjaIn the paper presented are the results of calculations using authors own model to predict heat transfer coefficient during flow boiling of carbon dioxide. The experimental data from various resea rches were collected. Calculations were conducted for a full range of quality variation and a wide range of mass velocity. The aim of the study was to test the sensitivity of the in-house model. The results show the importance of taking into...
-
Exergy analysis of the Szewalski cycle with a waste heat recovery system
PublikacjaThe conversion of a waste heat energy to electricity is now becoming one of the key points to improve the energy efficiency in a process engineering. However, large losses of a low-temperature thermal energy are also present in power engineering. One of such sources of waste heat in power plants are exhaust gases at the outlet of boilers. Through usage of a waste heat regeneration system it is possible to attain a heat rate of approximately...
-
MEASUREMENT OF TEMPERATURE-DEPENDENT VISCOSITY AND THERMAL CONDUCTIVITY OF ALUMINA AND TITANIA THERMAL OIL NANOFLUIDS
PublikacjaIn this study results of simultaneous measurements of dynamic viscosity, thermal conductivity, electrical conductivity and pH of two nanofluids, i.e. thermal oil/Al2O3 and thermal oil/TiO2 are presented. Thermal oil is selected as a base liquid because of possible application in ORC systems as an intermediate heating agent. Nanoparticles were tested at the concentration of 0.1%, 1% and 5% by weight within temperature range from...
-
Recuperator with microjet technology as a proposal for heat recovery from low-temperature sources
PublikacjaA tendency to increase the importance of so called dispersed generation, based on the local energy sources and the working systems uti- lizing both the fossil fuels and the renewable energy resources is observed nowadays. Generation of electricity on industrial or domestic scale together with production of heat can be obtained for example through employment of the ORC systems. It is mentioned in the EU directive 2012/27/EU for...
-
Parametric study of fluid flow and heat transfer over louvered fins of air heat pump evaporator
PublikacjaTwo-dimensional numerical investigations of the fluid flow and heat transfer have been carried out for the laminar flow of the louvered fin-plate heat exchanger, designed to work as an air-source heat pump evap- orator. The transferred heat and the pressure drop predicted by simulation have been compared with the corresponding experimental data taken from the literature. Two dimensional analyses of the louvered fins with varying...
-
Performance analyses of helical coil heat exchangers. The effect of external coil surface modification on heat exchanger effectiveness
PublikacjaThe shell and coil heat exchangers are commonly used in heating, ventilation, nuclear industry, process plant, heat recovery and air conditioning systems. This type of recuperators benefits from simple construction, the low value of pressure drops and high heat transfer. In helical coil,centrifugal force is acting on the moving fluid due to the curvature of thetube results in the development. It has been long recognized that the...
-
Heat transfer in plate heat exchanger channels: experimental validation of selected correlation equations
PublikacjaThis study is focused on experimental investigation of selected type of brazed plate heat exchanger. The Wilson approach was applied in order to estimate heat transfer coefficients for the PHEx passages. The main aim of the paper was to experimentally check ability of several correlations published in the literature to predict heat transfer coefficients by comparison experimentally obtained data with appropriate predictions. The...