wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: femtosecond phenomena
-
Technological Problems in Lapping on Flat Surfaces of Ceramic Parts
PublikacjaThis paper will present the results of research on single-disc lapping of flat surfaces of small ceramic elements. Machining with the use of different tools such as metallic, two-metallic and abrasive-metallic will be analyzed. The basics and techniques of reinforcement of laps will be discussed. The results of the influence of parameters on the surface quality of ceramic conponents (sealing) for three treatments on lapping machines...
-
Wear of Electroplated Tools Used for Flat Grinding of Ceramics
PublikacjaTwo methods for the abrasive properties evaluation, based on the image processing, are presented in the paper. Image processing analysis was developed to evaluate quickly the abrasive properties as the tool wears down. The coefficient based on the image brightness was calculated and additional analysis was based on the number of grains located on the active surface of the tool before and after machining. The active surfaces of...
-
Surface Structure of Components Created by Stereolitography
PublikacjaStereolithography is an additive rapid prototyping method. This method is based on the principle of solidifying a liquid photopolymer (resin) by laser radiation. Models obtained with this method are characterized by a specific surface structure called “stairstep effect”. It causes that, the surface should be processed by additional finishing (postprocessing). To minimize the additional machining process, the model should be set...
-
A simplified model of 3-D pipe system conveying flowing liquid
PublikacjaThe paper presents a model reduction technique of a 3-D pipe system with flowing liquid. In the analysis and design of control (mechatronic) systems it is useful to work with simple, low order models. A hybrid reduced order model is proposed. The system model consists of two parts, the modal model and the finite element model.
-
Influence of Flat Lapping Kinematics on Machinability of Ceramics
PublikacjaNew tools for flat grinding of ceramics are presented in the paper. Electroplated CBN tools (B64 and B107) were used in a modified single-disc lapping machine configuration. The results from experiments, such as the material removal rate and surface roughness parameters are presented and analyzed. Numerical simulations, based on the model for the shape error and tool wear estimation in machining with flat lapping kinematics, are...
-
Modelling of Geared Multi-Rotor System
PublikacjaIn the paper the method of modelling a speed-varying geared rotor system is presented. The proposed approach enables us to obtain an accurate low-order lumped parameter representation of the investigated system. The final model consists of reduced modal models of an undamped beam/torsional shaft system as well as a spatially lumped model of other linear and nonlinear phenomena including gear mesh interaction.
-
HILS for the Design of Three-Wheeled Mobile Platform Motion Surveillance System with a Use of Energy Performance Index
PublikacjaCurrent tendency in mechatronic design requires the use of comprehensive development of an environment, which gives the possibility to prototype, design, simulate and integrate with dedicated hardware. The paper discusses the Hardware-In-the-Loop Simulations (HILS) mechatronic technique, used during the design of the surveillance system based on energy performance index. The presented test configuration (physical controller – emulated...
-
Modelling of Ship’s Heeling and Rolling for the Purpose of Gantry Control Improvement in the Course of Cargo Handling Operations in Sea Ports
PublikacjaThe paper presents two proposals of models of interaction between a ship and cargo being loaded or discharged by a gantry in port, in terms of heeling and rolling of the vessel. The main purpose of such modelling is the need for improvement of gantry control with regard to faster operations thanks to more accurate estimation of level and moment of cargo release from a gantry hook or spreader. The study may be the contribution to...
-
Energy-Saving Mechatronic System for Fatigue Tests of Materials under Variable-Amplitude Proportional Bending and Torsion
Publikacja -
The Influence of Waste Expanded Perlite on Chemical Durability of Mortars
Publikacja -
Studies on the Preparation and Characterisation of Carbon Nanostructures
Publikacja -
Port-Based Modelling of Distributed-Lumped Parameter Systems
PublikacjaThere in the paper is presented an uniform, port-based approach to modelling of both lumped and distributed parameter systems. Port-based model of the distributed system has been defined by application of bond graph methodology and distributed transfer function method (DTFM). The approach proposed combines versatility of port-based modelling and accuracy of distributed transfer function method. The concise representation of lumped-distributed...
-
Modal Reduction and Analysis of Gyroscopic Systems
PublikacjaThe paper introduces the method of the modal reduction of systems that experience the Coriolis acceleration or gyroscopic effect component. In such cases corresponding system equations are non-self-adjoined. To solve the problem modal reduced model is built up for the system without Coriolis acceleration or gyroscopic effect terms. These phenomena are included by application of any lumping technique. Hence, the final reduced model...
-
Modeling and simulation of tool cycle in manufacturing cell
PublikacjaThe paper addresses issues concerning modeling and analysis of tool flow within a three-machine manufacturing cell used for small batch manufacturing of a definite spectrum of prismatic parts. The approach utilizes a method for job and tool allocation to work centers with limited number of machines and capacity of tool resources, based on the analysis of formalized relations: job - tool sets required. Selected tool flow control...
-
Optimum Control of Gyroscopic Systems
PublikacjaThe problem of optimum control of transverse rotor vibrations with gyroscopic interactions has been described and solved in the paper. An integral performance index has been defined for such system in order to minimize vibration level of a chosen rotor point. For this reason, an efficient way of finding the weight coefficients of integral performance index for multi-degrees-of-freedom system with gyroscopic interactions has been...
-
Analysis of Ceramic Elements with Ring-Crack Defects in Lubricated Rolling Contact
PublikacjaThe properties of ceramics, specifically low density, high hardness, high temperature capability and low coefficient of thermal expansion are of most interest to rolling element manufacturers. Surface ring cracks on lubricating rolling contact fatigue failure has been studied using numerical fracture analysis. Such cracks are very often found on ceramic bearing balls and decrease fatigue life rapidly. The numerical calculations...
-
Laser Surface Alloying of Aluminium Alloys with Cu/Fe Metallic Powders
Publikacja -
Laser Thermal Oxidation by Ytterbium-Doped Fibre Laser of the Hot and Cold-Rolled Stainless Steel Surface
Publikacja -
Structure and Mechanical Properties of Composite Layers Prepared by Laser Alloying of Aluminium Alloy
Publikacja -
The effect of pre-hydrogen charging on corrosion behaviour of superduplex stainless steel welded joints
PublikacjaThe paper presents results of research undertaken to determine the influence of hydrogen on passivity and corrosion resistance of 2507 super duplex stainless steel welded joints. Butt welded joints were made with low heat input using flux corded arc welding (FCAW) method. Coupons of 5.0 x 5.0 mm were cut from the welded joints containing weld metal (WM), heat affected zone (HAZ) and parent metal (PM). Hydrogen was introduced...
-
Deformation of the Structural Details of the Components Created by the Rapid Prototyping Method
PublikacjaThe paper present the results of preliminary research and describes the deformation of construction details within the process of producing small element employing a stereography system. The article discuses a scheme for changes in data conversion. Variation in construction details have been described on the basis of analysing photographs.
-
Hardened Steel Surface Waviness Created by Rolling Burnishing Process
PublikacjaThe surface of the finishing machined parts is defined mainly by roughness parameters. Growing demands on the part, especially mating sliding or rolling, require the specification of additional parameters, such as waviness parameters, particularly when there is significant resistance to seizing or noise reduction. This paper presents surface waviness characteristics of hardened burnished steel.
-
The Roughness of the Hardened Steel Surface Created by the Rolling-Burnishing Process
PublikacjaBurnishing hard materials can be used as an alternative finishing process. this paper presents the results of burnishing hardened steel. The article discusses surface deformation that occurs during this process and depends on the selected parameters of the geometric structure of the force applied for surface burnishing.
-
Evaluation of Wear Resistance of Ti alloys used for elements friction of knee endoprosthesis
PublikacjaThe paper presents research results of resistance to abrasive wear of titanium alloys: Ti6Al4V (commonly used) and Til3Nb13Zr (alloy of new generation) in association with polyethylene (UHMW-PE) predisposed for elements on pair of the knee endoprosthesis. The results were analysed from the point of possibility of an use of new generation titanium alloys as components of such implants. The tests of resistance to abrasive wear of...
-
Influence of Spatial Structures of 316L Stainless Steel on Its Cavitation Erosion Resistance
PublikacjaCavitation erosion performance of modified macroscopic internal structure 316L stainless steel was investigated. The samples processed by means of SLM method were subjected to cavitation erosion test. The scanning electron microscope Philips 30/ESEM was used to examine morphology of eroded surface.
-
Effect of Some Sulphur Additives on The Degradation of 9Cr-1Mo Steel After Its 10 Years Service in The CCR Platforming Unit
PublikacjaThe work shows the results of the tests of 9Cr-1Mo steel, which was for 10 years operated in the CCR platforming unit in Group Lotos SA in Gdańsk, and then in the laboratory was sulphidised during 166 h at a temperature of 600 °C. Sulphidation was performed in a mixture of H2-H2S gases at the vapour pressure of sulphur 4.1·10-14 atm, so the order of magnitude of vapour pressure was less than that of the dissociation pressure of...
-
Identification of the Inertia of Masses Flowing Water through the Pipes in Water Power Plants
PublikacjaW artykule przedstawiono sposób identyfikacji stałej czasowej reprezentującej bezwładność mas przepływającej wody w systemie rurociągów, w elektrowni wodnej. Przedstawiono strukturę modelu układu regulacji prędkości kątowej wykorzystywanego w procesie identyfikacji oraz przeprowadzono badania skuteczności działania metody w środowisku Matlab-Simulink. Opisano najistotniejsze wnioski wynikające z przeprowadzonych badań symulacyjnych.
-
Selected problems of navigation of educational mobile robot
PublikacjaW artykule przedstawiono ideę sterowania układem autonomicznego robota mobilnego skonstruowanego do celów edukacyjnych. Opisano strukturę mechaniczną układu, układy sensorów oraz zakres możliwości wynikających z działania oprogramowania robota.
-
The Behaviour Based Area Coverage of Unknown Environment by Autonomous Mobile Robot Using Modified ''The Way of the Ox'' Algorithm
PublikacjaPrzedstawiono propozycję rozwiązania zagadnienie całkowitego pokrycia terenu w układzie autonomicznego robota mobilnego. W tym celu zmodyfikowano algorytm "siewcy" oraz opracowano odpowiedni model układu, w środowisku Matlab-Simulink. Wykonano serię badań symulacyjnych, których najistotniejsze wyniki opisano w artykule.
-
Localization of Mobile Robot Using Radio Waves
PublikacjaOpisano systemy lokalizacji robotów mobilnych wykorzystujące metody triangulacji i trilateracji, w przestrzeniach dwuwymiarowych. Zaproponowano metodę pomiaru odległości drogą radiową oraz przedstawiono uzyskane wyniki badań.
-
Comparison the Accuracy of the Extrapolation Methods of the Time Phase Coincidence in Synchronization of Power Generating Units
PublikacjaW artykule opisano metody ekstrapolacji chwili zgodności fazowej napięć łączonych obiektów elektroenergetycznych. Przeprowadzono analizę porównawczą wybranych metod ekstrapolacji w równych warunkach pracy oraz przedstawiono najistotniejsze wyniki badań.
-
Redundantly Actuated 3RRR Parallel Planar Manipulator - Numerical Analyses of its Dynamics Sensitivity on Modifications of its Platform’s Inertia Parameters
PublikacjaIn the paper, numerical analyses, as well as dynamics of a complex mechanism, are presented. Two objectives are crucial for the paper: inverse dynamic model is needed (dedicated to be use in the model predictive controller); an identification method is searched (some trajectory parameters are controlled, when specific trajectory is tracked under an open-loop model-based control), as selected parameters must be identified for the...
-
Phase investigations of copper based CuZn38Al2MnFe alloy
PublikacjaW pracy przedstawiono analizę fazową mosiądzu CuZn38Al2MnFe. Wykazano, że obecność fazy Fe4Mn77Si19 powoduje kruchość stopu w teście zginania próbek.
-
Generation of Optimal Process Plan Alternatives for Manufacturing Mechanical Components
Publikacja -
Application of Syntactic Pattern Recognition Approach in Design and Optimisation of Group Machining Systems
Publikacja -
Identification of Kinematic Excitation Function by the Modal Coordinates Estimation of the System's Dynamics
PublikacjaThe paper presents a method of the kinematic excitation courses’ identification in excitation points, based on the car road test acceleration at different measurement points. For the purpose of the laboratory fatigue life investigation of contemporary complex structures (e.g. cars bodies) and components of these structures (i.e. cars roofs), only a few first vibration modes are usually taken into account. During real life tests...
-
Behavior Based Complete Coverage Task of Unknown Area by an Autonomous Mobile Robot SCORPION with Static Obstacles in Environment
PublikacjaIn the paper the behavior based control system of an autonomous mobile robot SCORPION is presented to execute the one of the most difficult navigation task, which is the complete coverage task of unknown area with static obstacles in the environment. The main principle assumed to design control system was that the robot should cover all area only once, if it possible, to optimize the length of path and energy consumption. All commercial...
-
Studies of the Modelling Accuracy of Steam Turbine Control Systems for Diagnostic Tests of Automatic Synchronizers
PublikacjaOne of the important factors that affect the reliable operation of the power system and the rapid restitution after disaster is a quick and effective combining synchronous electric power facilities to operate in parallel. Hence, diagnostics of automatic synchronizers at every stage of their life, from building a prototype, through the whole life, until removing such devices from the operation, is an extremely important and responsible...
-
The Optimal Spindle Speed Map for Reduction of Chatter Vibration During Milling of Bow Thruster Blade
PublikacjaW artykule przedstwiono przykład wykorzystania procedury tworzenia mapy optymalnych prędkosci obrotowych w celu ograniczenia drgań samowzbudnych podczas frezowania płata śruby okrętowego steru strumieniowego.
-
Mathematical Models of Control Systems of Angular Speed of Steam Turbines for Diagnostic Tests of Automatic and Mechatronic Devices
PublikacjaAccurate modeling of physical processes of many automatics and mechatronics systems is often necessity. In power system such a process is control of angular velocity of power objects during connection to operation in parallel. This process is extremely dynamic. For this reason response of control system depends from changes of many physical parameters (temperature, pressure and flow of the medium, etc.). Precision modeling influences...
-
Influence of geotechnical conditions on damage states of Gdansk Bay Coast cliff formations
PublikacjaA geotechnical aspect of destruction processes of seashores was identified based on the case of erosion of Gdansk Bay Coast cliff formations. Causative factors of landslide were described in the context of natural phenomena, land development and its anthropogenic transformations. Possible directions of theoretical analysis of changes in groundwater relations were indicated.
-
Synchronic digital stereophotography and photogrammetric analyses in monitoring the flow of liquids in open channels
PublikacjaThe authors present the results of their research into photogrammetric documents based on synchronic digital images. Examples presented in the paper indicate the value of synchronic stereophotography in registering phenomena connected with liquids. Combining synchronic stereophotography with photogrammetric methods has allowed the authors to develop an application useful for monitoring the flow of a liquid in an open channel.
-
FURTHER REMARKS ON THE SURFACE VIS IMPRESSA CAUSED BY A FLUID-SOLID CONTACT
PublikacjaIt is well-known that, nano-mechanics should take into account not only physical phenomena occuring within the bulk but, first of all, the physical phenomena appropriate for a surface of two materials contact. The huge volume density of internal surfaces as well countours lines located within the nanomaterial results in our interest in, apart from classical form of mass, momentum and entropy transport, those modes of transportation...
-
Surface Science - 2021/2022
Kursy OnlineThe goal of the subject is the presentation of basic problems resulting from he existence of interfacebetween material objects and its surroundings. Discussion of the consequences arising from the existenceof surface energy. Analysis of possible applications of surface phenomena in technology. Understanding ofproblems and benefits resulting from decreasing dimensions of objects with the special emphasis on thesemiconductor band...
-
Optical photoluminescent, and electroluminescent properties of organic solids
PublikacjaThis chapter discusses optical, photoluminescence and electroluminescence properties of organic materials. First, the spectral features of individual molecules and molecular solid states are analysed. Next, the excitonic processes in organic materials are discussed. The chapter reviews experimental methods leading to the determination of basic excitonic parameters. Finally, the electroluminescence phenomena in organic materials...
-
Comparison of properties of the new electro-mechanical model and circumferential model of the inductive-dynamic drive
PublikacjaThe article presents a new electromechanical model of inductive-dynamic drive. The model is implemented in two environments: Maxwell for analyzing electrodynamic phenomena including moving of the disc and Ansys which allows for stress analysis on the basis of the volume forces imported from Maxwell. Additionally, a model validation by comparing with the existing circumferential model was carried out.
-
Employment structure by enterprise size in Poland in 2010-2014
Dane BadawczeMicro, small and medium-sized enterprises employ in total nearly 70% of all employees working in the corporate sector. Micro enterprises play a decisive role in this respect, accounting for nearly 40% of all employees. This dataset contains data showing the structure of the number of employees in enterprises in 2010-2014.
-
Badania wstępne możliwości oceny stanu powierzchni tocznej szyn za pomocą zjawisk wibroakustycznych
PublikacjaW artykule przedstawiono wstępną koncepcję możliwości wykorzystania zjawisk wibroa-kustycznych w celu oceny stanu powierzchni tocznych szyn. Scharakteryzowano metodykę, zakres badań oraz wybór punktów lokalizacyjnych. Badania wstępne obejmowały pomiary drgań i hałasu na referencyjnym odcinku toru oraz na odcinku toru z wadą squat. Pomiary przeprowadzono na dwóch liniach kolejowych nr 213 Reda – Hel oraz 131 Chorzów Batory – Tczew....
-
Modelling of pipes conveying flowing liquid
PublikacjaThe paper introduces the method of modal reduction of system which consists of pipe with flowing liquid. The concept of hybrid model is proposed. The system model consists of two parts, the modal model and the finite elements model. The modal model represents linear, self-adjoined part of the system, while simple lumped technique is applied for modelling of Coriolis phenomena.
-
Janusz Cieśliński prof. dr hab. inż.
OsobyUrodził się 15 kwietnia 1954 r. w Słupsku. Jest absolwentem Wydziału Budowy Maszyn Politechniki Gdańskiej (1978), z którą związał całe swoje życie zawodowe. W 1986 r. obronił doktorat, w 1997 r. – habilitację, w 2006 r. – uzyskał tytuł profesora. Pełnił funkcje prodziekana ds. nauki Wydziału Mechanicznego przez dwie kadencje (2002–2008) oraz kierownika: Katedry Maszyn Przemysłu Spożywczego (2002–2006), Katedry Ekoinżynierii i...