![Profile photo: prof. dr hab. inż. Bogusław Kusz](/assets/boguslaw-kusz,3333-1/photo.png)
prof. dr hab. inż. Bogusław Kusz
Publications
Filters
total: 90
Catalog Publications
Year 2022
-
Pyrolysis of RDF and Catalytic Decomposition of the Produced Tar in a Char Bed Secondary Reactor as an Efficient Source of Syngas
PublicationOne of the technical limitations of refuse-derived fuel (RDF) pyrolysis is the high content of tar in its gas products. In order to resolve this problem, a two-stage RDF pyrolysis with a catalyst based on char from RDF pyrolysis is proposed. This paper presents the results of municipal waste pyrolysis beginning in an oven heated to 480 °C and ending with catalytic tar cracking carried out in the temperature range from 800 to 1000...
Year 2021
-
Kinetic analysis of the reduction of a ternary system of Bi, Sb and Te oxides by hydrogen for BiSbTe3 synthesis
PublicationReduction in a hydrogen atmosphere of Bi2O3, Sb2O3 and TeO2 mixes oxides for the synthesis of BiSbTe3 was analysed. The reduction reactions of Sb2O3 and Sb2O4 oxides, as well as Bi2O3+Sb2O3 and Sb2O3+3TeO2 mix- tures, were also evaluated. The reduction of Sb2O4 is investigated for the first time. The reactions of the mixed oxides systems also were not the subject of research so far despite being used for synthesis of the (Bi,Sb)2Te3...
-
Structure and thermoelectric properties of nickel-doped copper selenide synthesised in a hydrogen atmosphere
PublicationNickel-doped copper selenide—Cu2-xNixSe (x = 0; 0.01; 0.02; 0.03)—materials with high thermoelectric properties were synthesised through reduction of reagents in hydrogen. The impact of the nickel content on both the microstructure and thermoelectric properties was examined. The nickel-doped samples’ microstructure differed significantly from pristine copper selenide. Besides Cu2Se, copper precipitations were present in the materials....
-
The unstable thermoelectric effect in non-stoichiometric Cu2Se during the non-equilibrium phase transition
PublicationThe superionic α ↔ β phase transition in Cu1.96Se thermoelectric material is investigated by means of thermal analysis (DSC) and measurements of Seebeck coefficient and electrical conductivity. Results of the DSC measurements with 1–10 K/min heating and cooling rates show that the material is close to the equilibrium phase composition during the transformation. However, the kinetic limitation of the process exists, which is indicated...
Year 2020
-
A study of the kinetics of bismuth telluride synthesis by an oxide reduction method
PublicationThe kinetics of a reduction of bismuth and tellurium oxides in a hydrogen atmosphere, leading to the formation of thermoelectric bismuth telluride is investigated. The evaluation of the reaction kinetics was based on a thermogravimetric analysis performed in non-isothermal conditions. A non-parametric analysis method and the Friedman method were used for the evaluation of the data. Additionally, for a better understanding of the...
-
New synthesis route of highly porous InxCo4Sb12 with strongly reduced thermal conductivity
PublicationHighly porous, In-filled CoSb3 skutterudite materials with an attractive thermoelectric figure of merit (ZT * 1) and corresponding dense samples were fabricated through the cost-effective method of reduction in oxides in dry hydrogen and the pulsed electric current sintering (PECS) method, respectively. The reduction process was described in detail using in situ thermogravimetric analysis of Co2O3, Sb2O3 and In(NO3)35H2O separately...
Year 2018
-
A study of a reduction of a micro- and nanometric bismuth oxide in hydrogen atmosphere
PublicationA reduction of bismuth oxide in hydrogen atmosphere was investigated. The reaction was performed with a material in various structural forms: powder: with micrometric grains, powder with nanometric grains and powder pressed into pellets. The process was performed in both isothermal and non-isothermal conditions. An activation energy of the reaction calculated with Friedman method was found to be about 85 kJ/mol for the reduction...
-
Determination of ionic conductivity in the Bi-Si-O and Pb-Si-O glasses
PublicationImpedance spectroscopy measurements in various gas atmospheres were carried out in order to explain the doubts about the type of carriers and the mechanism of electrical conductivity in Bi-Si-O and Pb-Si-O glasses. In bismuth silicate glass, a typical ionic conductivity with oxygen ions as charge carriers was observed. The level of electrical conductivity of the glass at 400 °C was 5 × 10−8 S·cm−1 , with the activation energy of...
-
Structure and thermoelectric properties of bismuth telluride—Carbon composites
PublicationCarbon nanotubes and amorphous carbon have been introduced into a bismuth telluride matrix (0.15 and 0.30 wt.% ratio) to investigate the influence of the carbon on the composite’s thermoelectric properties. Composites with well-dispersed additives have been obtained by sonication and ball-milling methodology. Carbon nanotubes and an amorphous carbon addition led to a decrease in electric conductivity from 1120 S/cm to 77 S/cm....
Year 2017
-
Oxygen biosensor based on carbon nanotubes directly grown on graphitic substrate
PublicationFilms of carbon nanotubes were synthesized on the graphitic substrates by CVD method in the presence of catalyst. Two different catalysts were used, that is nickel and iron, supported on graphitic substrates. The as-obtained nanotubes were analyzed by SEM imaging with EDX and Raman spectroscopy. The results revealed their multi-walled morphology. Free radical reaction was carried out in order to chemically functionalize synthesized...
-
Structure and electrical properties of Y, Fe-based perovskite mixed conducting composites fabricated by a modified polymer precursor method
PublicationIn this work, samples of Y0.07Sr0.93Ti1-xFexO3-d with 20, 40, 60 and 80 mol% of iron amount were prepared by a low-temperature polymer precursor method. The SEM-EDS analysis proved that analyzed Y0.07Sr0.93Ti1-xFexO3-d samples were composites of two Ti- and Fe-rich perovskite samples. This kind of composite consists of two phases in which one has a good ionic and the other electronic conductivity, which makes such a composite a...
-
Structure and thermoelectric properties of Cs-Bi-Te alloys fabricated by different routes of reduction of oxide reagents
PublicationCesium-bismuth-telluride polycrystalline materials were fabricated using a cost-effective method based on a reduction of oxide reagents, leading to a production of a material with good thermoelectric properties. Several samples with various initial stoichiometry were prepared by melting of oxide powders at 1050 °C, quenching, milling to powders and then reducing in pure hydrogen at 400 °C. Another concept was to obtain the CsBi4Te6...
Year 2016
-
Characterization of structural, thermal and mechanical properties of bismuth silicate glasses
Publicationhe influence of heating and reduction processes on the structural, thermal and mechanical properties of bismuth-silicate glasses has been investigated. Two compositions of glasses: 40Bi2O3–60SiO2 (Bi0.57Si0.43Ox) and 27Bi2O3–73SiO2 (Bi0.43Si0.57Ox) were fabricated by a typical melt quenching technique. Then the reduction in hydrogen at 380 °C for 20, 42 or 67 h was performed. It was found that a 50 μm-thick layer was formed on...
-
Determination of the ionic conductivity of Sr-doped lanthanum manganite by modified Hebb–Wagner technique
PublicationThe Hebb–Wagne rpolarization method with the electron blocking electrode has been discussed in this paper in aim to determine a partial ionic conductivity of Sr-doped lanthanum manganite.The “limiting current” in the proposed system was measured using the two-point DC technique with additional Pt electrode between LSM and blocking electrode.The electrochemical model based on bulk diffusion processes and Boltzmann statistics has...
-
Novel method for metal-oxide glass composite fabrication for use in thermoelectric devices
PublicationA novel method for thermoelectric materials fabrication using a reduction of oxide precursors in hydrogen was reported. On the example of Bi-Sb, Bi-Sb-Te and Te-Ag-Ge-Sb compounds it was shown that this simple and easy method is suitable for fabrication of two-, three- and even multicomponent thermoelectric materials. It allows controlling a composition, microstructure and even type a of electrical charge carriers. As a result...
-
Structure and thermoelectric properties of Te/Ag/Ge/Sb (TAGS) materials obtained by reduction of melted oxide substrates
PublicationThe Ge0.77Ag0.1Sb0.13Te1alloy was fabricated by a novel two step route. For that purpose firstly the oxide reagents were melted at high temperature and quenched into pellets. After that pellets were milled to the powder and then reduced in hydrogen at various temperatures and for various periods of time. Energy dispersive X-ray analysis indicated the possibility of successful fabrication of stoichiometric thermoelectric materials...
-
Synthesis and structural properties of (Y, Sr)(Ti, Fe, Nb)O3−δ perovskite nanoparticles fabricated by modified polymer precursor method
PublicationThe yttrium, iron and niobium doped-SrTiO3 powders have been successfully fabricated by a modified low–temperature synthesis method from a polymer complex. The usage of strontium hydroxide precursor instead of conventional strontium nitrate or strontium carbonate provides to the possibility of significant decrease of annealing temperature. It allows to prepare a material with sphere-shape grains of nanometric size (15–70 nm). The...
-
Thermoelectric properties of bismuth-antimony-telluride alloys obtained by reduction of oxide reagents
PublicationThe BieSbeTe alloys with different Bi/Sb/Te ratio were fabricated by an innovative method. For that purpose the oxide reagents were melted at high temperature, then quenched to form pellets, milled to a powder and finally reduced in hydrogen at various temperatures. Complex structures consisting of connected thin layers forming a continuous path between nano- and micrometer size grains have been obtained. The electrical conductivity,...
Year 2015
-
Planowanie eksperymentu
PublicationW pracy przedstawiono schemat postępowania przy planowaniu eksperymentu naukowego
-
Structure and thermoelectric properties of Bi–Te alloys obtained by novel method of oxide substrates reduction
PublicationA novel method of thermoelectric materials fabrication has been developed. Oxide reagents have been melted at high temperature in air, quenched, milled to powder and reduced in hydrogen to form Bi–Te alloys. Structural and thermoelectric properties of samples have been investigated depending on initial composition and temperature of reduction process. Sample 25Bi2O3–75TeO2 reduced at 340 °C for 10 h has been found to be a p-type...
Year 2014
-
Correlation between structural and electrical properties in highly porous (Y,Sr)(Ti,Nb)O3-delta SOFC anodes
PublicationIn order to find a relationship between structural and electrical properties, niobium and yttrium doped SrTiO3 ceramics were prepared via solid-state reaction. The samples were sintered in hydrogen and air conditions. The samples were also fabricated with a pore-former to obtain highly porous specimens. The electrical properties of Nb-doped SrTiO3 samples and yttrium and niobium co-doped SrTiO3 were compared. The comparable electrical...
-
Metodyka wykonywania pomiarów oraz ocena niepewności i błędów pomiaru
Publicationelem każdego ćwiczenia w laboratorium studenckim jest zmierzenie pewnych wielkości, a następnie ob- liczenie na podstawie tych wyników pomiarów wartości wielkości badanej. Rezulta- tem końcowym badań jest nie tylko otrzymany wynik liczbowy. Nie mniej ważne jest dokonanie oceny dokład- ności pomiaru oraz opraco- wanie wniosków końcowych. Warto zadać sobie pytanie: czy to, co zostało zmierzone, ma sens i co z tego wynika?...
-
The properties of reduced Bi-Ge-O glasses for thermoelectric devices
PublicationThe bismuth-germanate glasses have been investigated to examine their applicability for thermoelectric devices. In order to increase their electrical conductivity, the 25Bi2O3–75GeO2 glass samples have been reduced at 340-380°C for 10 hours in hydrogen. It has been shown that such heat treatment in H2 leads to the reduction of metal ions Bi3+ and Ge4+ into neutral atoms and the formation of metal grains both in an amorphous glass...
-
The properties of reduced Ge-Sb-O glasses for thermoelectric devices
PublicationThe structural and electrical properties of germanium-antimonate glasses after heat treatment in hydrogen have been determined. In the case of 50GeO2-50Sb2O3 glass reduced at 340°C even for less than 1 hour a continuous layer of antimony granules is formed and its electrical properties determine the surface conductivity of the reduced sample. The bulk electrical conductivity at 100°C of this sample was determined as 1000 Scm-1...
-
Wiedza ogólna o eksperymencie naukowym
PublicationW pracy przedstawiono podstawowe pojęcia z zakresu metodologii badań w nauce i w technice
Year 2013
-
Application of wet powder spraying for anode supported solid oxide fuel cell with a perowskite SrTi0.98Nb0.02O3-d anode
PublicationAnode-supported solid oxide fuel cell with SrTi0.98Nb0.02O3–d anode, yttria-stabilized zirconia electrolyte and La(Ni0.6Fe0.4) O3d cathode has been successfully fabricated and evaluated. Process of anode support fabrication has been presented. Wet powder spraying and high temperature sintering method have been studied and applied to deposit the thin electrolyte layer.In order to improve catalytic properties of the anode, it has...
-
Characterization of CaTi0.9Fe0.1O3/La0.98Mg0.02NbO4 composite
PublicationA composite of CaTi0.9Fe0.1O3 and electrolyte material, i.e. magnesium doped La0.98Mg0.02NbO4 was prepared and studied. The phase content and the sample microstructure was examined by an X-ray diffraction method and scanning electron microscopy. EDS measurements were done both for composite samples and the diffusion couple. The electrical properties were studied by four terminal DC method. The Ahigh-temperature interaction between...
-
Interactions between components of SrTi0.98 Nb0.02O3-δ-YSZ and SrTi0.98 Nb0.02O3-δ -CeO2 composites
PublicationComposites consisting of SrTiO3-based perovskite and either yttria-stabilized zirconia or ceria were investigated. The mechanical compatibility and possible inter-diffusion between phases were characterized by scanning electron microscopy, X-ray diffraction, and energy-dispersive X-ray spectroscopy. A gradual disappearance of Ce-containing phases with an increase in the temperature of reduction in hydrogen was noticed. Moreover,...
-
Investigation methods of ionic conductivity measurements in polycrystalline MIEC (mixed ionic-electronic conductor) based on perovskite ceramics
PublicationPaper about the measurements of ionic conductivity in LSM and strontium titanate ceramics.
-
Investigation of functional layers of solid oxide fuel cell anodes for synthetic biogas reforming
PublicationSolid oxide fuel cells (SOFCs) are one of the most promising energy conversion devices due to their high efficiency, low pollution and fuel flexibility. Unfortunately, when hydrocarbons are used as a fuel, for example in the form of a biogas, solid carbon can deposit on the anode surface. This process leads to the degradation of the fuel cell performance. A possible solution to this problem is to apply an additional catalytic material,...
-
YSZ Thin film deposited on porous substrate by spray pyrolysis
PublicationIn this work the results of deposition of YSZ layer on a porous substrate using an ultrasonic Spray Pyrolysis are presented.
Year 2012
-
Donor-substituted SrTi1+xO3−δ anodes for SOFC
PublicationNonstoichiometric Nb-substituted SrTiO3 compounds were investigated in order to discuss the influence of nonstoichiometry at the sample properties in the light of recent results reported in the literature. Structural and electrical properties of samples were characterized. Investigated compounds were also applied as anodes for Solid Oxide Fuel Cells and their reactivity with YSZ electrolyte was examined. The defect chemistry explaining...
-
Donor-substituted SrTi1+xO3−δ anodes for SOFC
PublicationPrzebadano wpływ niestechiometrii na właściwości tytanianu strontu domieszkowanego niobem. Zaproponowano chemię defektów dla tego typu związków.
-
High temperature monoclinic-to-tetragonal phase transition in magnesium doped lanthanum ortho-niobate
PublicationMagnesium doped lanthanum ortho-niobate (La0.98Mg0.02NbO4) was prepared by the molten salt synthesis method. X-ray diffraction and dilatometry methods were used to study high temperature behavior of the ceramic material. Special attention was paid to the phase transition between the monoclinic and tetragonal phases. The values of spontaneous strain on the basis of unit cell parameter, obtained by Rietveld refinement, have been...
-
Materiały katalityczne dla tlenkowych ogniw paliwowych zasilanych biogazem
PublicationTlenkowe ogniwa paliwowe (SOFC) są jednymi z najbardziej obiecujących przyrządów do konwersji energii ze względu na wysoką wydajność, niską emisję zanieczyszczeń i możliwość zastosowania szerokiej gamy paliw. Jednak zastosowanie biogazu jako paliwa w obecnie wytwarzanych ogniwach paliwowych, w których anoda jest zbudowana z niklu i tlenku itru stabilizowanego tlenkiem cyrkonu, powoduje osadzanie się węgla oraz degradację ogniwa....
-
Microstructural and electrical properties of Y0.07Sr0.93-xTiO3 perovskite ceramics
PublicationIn order to find a relationship between electrical and microstructural properties, yttrium-doped strontium titanate (7 mol%) with various values of strontium nonstoichiometry was investigated and shown in this work. It has been observed that yttrium doping can affect the electrical properties of SrTiO3 to a great extent. Moreover, the microstructural and electrical properties can be influenced by strontium nonstoichiometry. The...
-
Microstructural and electrical properties of Y0:07Sr0:93−xTiO3− perovskite ceramics
PublicationIn order to find a relationship between electrical and microstructural properties, yttrium-doped strontium titanate (7 mol%) with various values of strontium nonstoichiometry was investigated and shown in this work. It has been observed that yttrium doping can affect the electrical properties of SrTiO3 to a great extent. Moreover, the microstructural and electrical properties can be influenced by strontium nonstoichiometry. The...
-
Microstructural and electrical properties of Y0.07Sr0.93-xTiO3-δ perovskite ceramics
PublicationIn order to find a relationship between electrical and microstructural properties, yttrium-doped strontiumtitanate (7 mol%) with various values of strontium nonstoichiometry was investigated and shown in this work.It has been observed that yttrium doping can affect the electrical properties of SrTiO3 to a great extent.Moreover, the microstructural and electrical properties can be influenced by strontium nonstoichiometry.The defect...
-
Microstructure and electrical properties of SrTi0.98Nb0.02O3-δ-based composites applied as porous layers for SOFCs
PublicationPrzebadano właściwości elektryczne oraz strukturalne kompozytów Sr(Ti,Nb)O3-YSZ i Sr(Ti,Nb)O3-CeO2 naniesionych w postaci warstw porowatych na podłoża YSZ
-
Optimization of microstructure and properties of acceptor-doped barium cerate
PublicationThe presented research concerns acceptor doped barium cerate and the attempts of improvement of its production method that would allow obtaining the solid electrolyte characterized by the particular properties. The authors suggest combining two production methods, molten salt synthesis and self-combustion, in order to achieve the compound material that has some of the advantages of both of the initial methods. An impact of nickel...
-
Perovskites in Solid Oxide Fuel Cells
PublicationPrzeglądowa publikacja dotycząca wykorzystania ceramicznych materiałów perowskitowych w tlenkowych ogniwach paliwowych.
-
Solid Oxide Fuel Cells with Ni infiltrated perovskite anode
PublicationNiobium-doped strontium titanate was used as the anode for a solid oxide fuel cell. Electrolyte-supported cells were prepared with pure perovskite and composite perovskite–yttria–stabilized-zirconia (YSZ) anodes. Fuel cell tests demonstrated significant improvement in power density after infiltration with a small amount of Ni. The obtained values of power densities are comparable with conventional Ni/YSZ cermet anode. In addition,...
-
Solid oxide fuel cells with Ni-infiltrated perovskite anode
PublicationWytworzono próbki na bazie tytanianu strontu domieszkowanego niobem i przebadano wpływ nasączania niklem na właściwości tych materiałów.
-
Structural and electrical properties of Sr(Ti,Fe)O3-δ materials for SOFC cathodes
PublicationW niniejszym artykule, dwa związki SrTiO3 domieszkowanego Fe przebadano pod względem przydatności na katody w tlenkowych ogniwach paliwowych. SrTi0.65Fe0.35O3 i SrTi0.5Fe0.5O3 zostały przebadane pod względem reaktywności chemicznej z elektrolitem YSZ. Stwierdzono, że przewodnictwo elektryczne tych związków jest stosunkowo niskie: 0,4 S/cm i 2 S/cm odpowiednio dla STF35 i STF50.
-
The comparison of SrTi0.98Nb0.02O3–δ-CeO2 and SrTi0.98Nb0.02O3–δ-YSZ composites for use in SOFC anodes
PublicationComposites of Nb-doped strontium titanate mixed with yttria-stabilized zirconia or cerium oxide in 50:50, 70:30 and 85:15 weight ratios were evaluated as possible anode/electrolyte interface materials for solid oxide fuel cells in terms of chemical compatibility, electrical conductivity and mechanical properties. It has been shown that composite samples prepared by typical powder-mixing methods remain single-phase up to 1400°C....
-
The comparison of SrTi0.98Nb0.02O3-δ-CeO2 and SrTi0.98Nb0.02O3-δ-YSZ composites for use in SOFC anodes
PublicationWytworzono i przebadano właściwości strukturalne i elektryczne kompozytów SrTi0.98Nb0.02O3-δ-CeO2 i SrTi0.98Nb0.02O3-δ-YSZ. Przeprowadzono testy materiałów zastosowanych jako anody w tlenkowych ogniwach paliwowych.
Year 2011
-
Influence of pore formers on electrical properties of CaTi0.9Fe0.1O3-δ perovskite-type ceramics
PublicationPorous CaTi0.9Fe0.1O3-δ (CTF) perovskites were synthesized by the standard solid state method at different sintering temperatures with carbon black (CB), corn starch (CS) and potato starch (PS) as pore-forming agents. The ceramic samples of porosity between 9% and 42% with 5 - 40 μm pore sizes, were obtained by a 6 h sintering at either 1130º C or 1200º C of precursor powder prepared at 1470º C. X-ray diffraction analysis proved...
Year 2010
-
Electrical and structural properties of Nb-doped SrTiO3
PublicationNiobium-doped strontium titanate synthesized via conventional solid-state reaction has been studied. Influence of niobium content on the lattice parameters and electrical conductivity has been reported. Various reduction conditions have been investigated. For samples reduced in hydrogen at 1400°C, a transition from thermally activated to metallic behavior has been observed. Maximum electrical conductivity (ca. 55 Scm−1 at 650°C)...
-
Nano - and microcrystals of doped niobates
PublicationPublikacja przedstawia wyniki analizy pomiarów wysokotemperaturowej rentgenografii strukturalnej niobanu lantanu domieszkowanego magnezem.
-
Structure and electric properties of double magnesium zirconium orthophosphate
PublicationPublikacja przedstawia wyniki pomiarów elektrycznych i strukturalnych ortofosforanu magnezowo-cyrkonowego.
seen 17736 times