Filters
total: 135
filtered: 120
-
Catalog
Chosen catalog filters
Search results for: PAVEMENT TEMPERATURE
-
High frequency impulse ground penetrating radar application in assessment of interlayer connections
PublicationGround Penetrating Radar (GPR) technique is commonly used in the nondestructive evaluation of pavement structures. In particular, this method is used to estimate thicknesses of pavement layers as well as it can be utilized in advanced studies of pavement structures. The device presented in this paper comprise the high frequency impulse antennas that allow for investigating the interlayer zones in terms of their electromagnetic...
-
Effect of interlayer bonding quality of asphalt layers on pavement performance
PublicationThe quality of interlayer bonding at the interfaces between the asphalt layers in flexible pavements affects the overall pavement performance. Lack or partial lack of interlayer bonding between asphalt layers can cause pavement's premature failures such as rutting, slippage of the wearing course, cracking or simply a reduction in the calculated fatigue life of the pavement structure. This paper shows the case studies of investigation...
-
Noise measurements on low noise pavements - problems with inhomogeneity of wearing course
PublicationDuring the last several years, when performing numerous CPX noise measurements on low noise pavements,significant inhomogeneity of the wearing course was observed in numerous cases. Similar problems were almost not existing regarding to the dense pavements.In general three main reasons of inhomogeneity can be defined. The first one are imperfections in technology of production of a asphalt mix or/and errors made already during...
-
Initial Field Validation of Poroelastic Pavement Made with Crumb Rubber, Mineral Aggregate and Highly Polymer-Modified Bitumen
PublicationTire/road noise in most driving conditions dominates other sources of traffic noise. One of the most efficient ways of reducing tire/road noise is to use the so-called “low noise pavement”. According to numerous studies, at present, poroelastic road pavement that is composed of rubber and mineral aggregate and polyurethane or bituminous binder gives the best noise reduction up to 12 dB. Unfortunately, there are many problems with...
-
Inhomogeneity of low-noise wearing courses evaluated by tire/road noise measurements using the close-proximity method
PublicationPerforming numerous analyses of tire/road noise measurements on low-noise pavements during the last several years, the authors observed significant inhomogeneity of the wearing course in numerous cases, while similar problems were almost non-existent when dense pavements were measured. Three main causes of low-noise pavement inhomogeneity can be defined. The first one is imperfections in the technology used for asphalt mix production...
-
Determination of Vehicles Load Equivalency Factors for Polish Catalogue of Typical Flexible and Semi-rigid Pavement Structures
PublicationThe new Polish Catalog of Typical Flexible and Semi-rigid Pavement Structures was introduced to use in practice in 2014. Much of works were focused on actualization of vehicles load equivalency factors. For this purpose data delivered from weigh-inmotion were analyzed. Four methods of determination of load equivalency factors for pavement structure design were compared. The analysis showed that fourth power equation, AASHTO 1993...
-
Tire camber angle influence on tire-pavement noise
PublicationTaking into account tire-pavement noise and tires classification with respect to noise emission special measurement methods are usually used. When two of them are applied (the Laboratory Drum Method (DR) and the Close-Proximity Method (CPX)) the investigator has to be sure that the position of the tire is correct. The authors of this paper thought about tire position as tire (wheel) alignment in particular tire camber angle. They...
-
The best porous asphalt pavement in Sweden so far
PublicationIn 2010 a double-layer porous asphalt concrete (DPAC) pavement was constructed in various versions on the E4 motorway through the Swedish city Huskvarna. As a result of a court decision the Swedish Transport Administration had to reduce noise emission by applying a low noise road surface that would reduce A-weighted noise levels by 5 dB, as an average. Earlier experience in Sweden indicated that it was possible to obtain a high...
-
Acoustic lifecycle study of the double-layer porous asphalt on E4 in Huskvarna, Sweden
PublicationIn 2010 a double-layer porous asphalt concrete (DPAC) pavement was constructed on the E4 motorway through the Swedish city Huskvarna. Earlier experience in Sweden indicated that it was feasible to obtain a high initial noise reduction but due to the widespread use of studded tires in winter, clogging and ravelling created losses of around 2 dB per year, with an expected acoustical lifetime of only 3 years. However, the improved...
-
Editorial, SI EATA2023
PublicationThe European Asphalt Technology Association (EATA) is an organisation of leading European engineers and scientists involved in the asphalt material research. Every two years, the EATA celebrates its international pavement conference, with the aim of disseminating the key advances in scientific knowledge related to asphalt materials and technologies, and to encourage the transfer and application of this knowledge worldwide. Since...
-
Laboratory fatigue assessment of large geocomposite-reinforced double-layered asphalt concrete beams
PublicationGeosynthetic reinforcement of asphalt layers has been used for several decades. Evaluation of the influence of these materials on pavement fatigue life is still ongoing, especially for new types of geocomposites. This paper presents the evaluation of fatigue performance of large asphalt concrete beams reinforced with a new type of composite in which square or hexagonal polypropylene stiff monolithic paving grid with integral junctions...
-
Laboratory fatigue assessment of large geocomposite-reinforced double-layered asphalt concrete beams
PublicationGeosynthetic reinforcement of asphalt layers has been used for several decades. Evaluation of the influence of these materials on pavement fatigue life is still ongoing, especially for new types of geocomposites. This paper presents the evaluation of fatigue performance of large asphalt concrete beams reinforced with a new type of composite in which square or hexagonal polypropylene stiff monolithic paving grid with integral junctions...
-
Katedra Inżynierii Drogowej. Zakład Budowy Dróg.
PublicationDepartment of Highway Engineering is divided into two divisions: Road Construction Division and Traffic Engineering Division. The head of Road Construction Division is Prof. J. Judycki. There are nine members of division: professor, three PhD, two MSc, two technicians and secretary. The main areas of research activities are: analysis of flexible, semi-rigid and rigid pavements, resistance of asphalt pavement to permanent deformation,...
-
Radar technique in application of interlayer identification connections
PublicationOne of important issues in pavement construction is to ensure that layers applied directly one on top of the other make up a continuous whole and form an integral construction complex. An appropriate interlayer connection plays here significant role ensuring proper transmission of distortions generated by wheels of vehicles to lower layers and preventing water penetration between the layers. In case of damaged pavements where lack...
-
Pavement ageing influence on tyre/road noise
PublicationRoad surface should be constructed in a way that ensures safe and comfortable traffic conditions, not only when it is newly paved but also during its entire lifetime. An important factor in the asphalt mixture design process is also the expected pavement durability and stability of pavement properties over time. In many countries, road surface starts to play a significant role in traffic noise reduction actions. Selecting a particular...
-
Poroelastic Road Surface – a Promising Road Traffic Noise Abatement Solution
PublicationRoad surfaces have a direct impact on the generation of noise by rolling tyres, the main and dominant source of noise of moving vehicles, as well as may affect propagation of noise emitted by all noise sources of a vehicle. Thus there is no doubt that pavement should be considered as one of the major potential road traffic noise abatement measure. Low noise pavements of existing types may in new conditions provide up to 8 dB of...
-
Crack Resistance of Asphalt Concrete Subjected to Environmental Factors
PublicationThe paper presents an analysis of the influence of environmental factors on the cracking susceptibility of asphalt concrete resulting in a change in the durability of asphalt pavement. In order to assess the phenomenon, laboratory tests were carried out taking into account the destructive effects of moisture, freeze-thaw cycle and long-term ageing. The influence of both factors occurring simultaneously was also verified. Due to...
-
Assessment of the application of CEM III with exposed aggregate as an alternative to CEM I for road pavements
PublicationThe article presents a results of study on the impact of replacing CEM I SR3/NA by CEMIII/A LH/HSR/NAon the mechanical properties and durability of pavement concrete with exposed aggregate. Was used granite aggregate and washed sand. Water/cement () ratio in the tested concretes constituted 0.35 and 0.4 and part of the cement was replaced with a 5% addition of natural pozzolana – zeolite. Compressive strength tests were performed...
-
Retrofitted vibro-pressed pavement bricks and their impregnation in modern architecture.
PublicationRecent construction projects require new properties of concrete building materials. The paper describes the technological methods of retrofitting of vibro-pressed concrete pavement brick and shows the results of improving physical properties of concrete by application of different impregnation agents.
-
Comparison of road and laboratory measurements of tyre/road noise
PublicationTyre/road noise is one of the major environmental problems related to road traffic. There are several measuring methods of tyre/road noise that may be carried out on the road (for example Coast-down and Close Proximity Method) or in the laboratory (Drum Method). Road measurements are preferred for evaluations of pavement properties while laboratory methods are mostly used to evaluate tyres. One of the biggest problems associated...
-
The use of weight in motion data to heavy vehicles - pavement interaction analysis
PublicationWeight in motion (WIM) is the element of modern intelligent transport systems created to control commercial vehicles and to detect overloaded items. Because all of the vehicles crossing the WIM station are weighed and recognized, given data can be used to vehicle-pavement interaction analysis. The paper presents the results of analysis based on data from seven WIM stations localized in Motorway and National Roads in Poland. The...
-
Application and evaluation of M-EPDG for performance analysis of Polish typical flexible and rigid pavements
PublicationThe main goal of the paper is to implement and evaluate the M-EPDG and the software AASHTOware to analyse the performance of new flexible and rigid pavements designed according to the Polish catalogues, which are comparable with analogous catalogues used in other European countries. For this purpose the site-specific inputs for Poland were determined and described in the paper as well as compared to the default input data used...
-
INFLUENCE OF DATA NORMALIZATION ON THE EFFECTIVENESS OF NEURAL NETWORKS APPLIED TO CLASSIFICATION OF PAVEMENT CONDITIONS – CASE STUDY
PublicationIn recent years automatic classification employing machine learning seems to be in high demand for tele-informatic-based solutions. An example of such solutions are intelligent transportation systems (ITS), in which various factors are taken into account. The subject of the study presented is the impact of data pre-processing and normalization on the accuracy and training effectiveness of artificial neural networks in the case...
-
Determination of equivalent axle load factors with the use of strain energy of distortion
PublicationThe paper proposes a new method for calculation of equivalent axle load factors based on the analysis of strain energy of distortion induced in road pavements by traffic loads. The main advantage of the method is the more accurate calculation of the effects of multiple axles and super single versus dual tyres. The methodconsiders the location of critical points, at which strain energy of distortion reaches extreme values. When...
-
Contribution of dynamic vehicle loads to pavement failure
PublicationPavement surfaces are not ideally even, which causes dynamic loads of vehicle axles. Distribution of dynamic loads of a given axle is similar to normal distribution and can be described by static load and dynamic load coefficient. The dynamic load coefficient depends on road profile, vehicle speed, properties of suspensions and static load of axle. While for a given road section road profile remains constant, vehicle speed and...
-
Poroelastic Road Surfaces - State of The Art
PublicationPoroelastic Road Surfaces (PERS) constitute a specific group of pavements containing a great amount of crumbled rubber. In most cases rubber aggregate constitutes about 20% of the mixture (by weight) and a polyurethane resin is used as a binder. As a result, PERS is characterized by a much higher elasticity than asphalt and a high porosity typical for drainage pavements. Due to this, tire/road noise is greatly reduced and on top...
-
Effect of Overloaded Vehicles on Whole Life Cycle Cost of Flexible Pavements
PublicationThe phenomenon of vehicle overloading—illegal exceeding of maximum legal weight of vehicles, is a serious problem both in developing and developed countries around the world. Overloaded vehicles occur less frequently in comparison to properly loaded vehicles but due to their greater potential to cause damage they significantly contribute to distress of pavement structure. As studies show, the number of overloaded vehicles increases...
-
Investigation of Acoustic Properties of Poroelastic Asphalt Mixtures in Laboratory and Field Conditions
PublicationMeasures for the improvement of acoustic conditions in the vicinity of roads include the construction of pavement structures with low-noise surfaces with optimal macrotexture and the highest possible sound absorption coefficient. Laboratory evaluation of acoustic properties of a designed asphalt mixture before its placement in the pavement is a good solution. Currently, the most popular method for the determination of the sound...
-
Road texture influence on tyre rolling resistance
PublicationTyre performance, one of the critical factors for vehicle users, is strongly related to theroad surface characteristics, most notably to the pavement texture. Phenomena that occur at the tyre/road interface affect tyre friction (skid resistance), rolling resistance, tyre wear and tyre/road noise. This article deals with relationship between surface texture and rolling resistance of light and heavy vehicle tyres. Mean profile depth...
-
Quantifying the effective mobilized RAP content during hot in-place recycling techniques
PublicationThe utilization of in-place recycling techniques is capable of consuming 100% reclaimed asphalt pavement (RAP). Hot in-place recycling (HIR) is one of the promising techniques to rehabilitate the pavements suffering from minor cracking issues through heat scarification, additive injecting, mechanical mixing, and compacting. However, the main concern of using 100% RAP in HIR remains as how much RAP can be activated and mobilized...
-
Machine learning applied to acoustic-based road traffic monitoring
PublicationThe motivation behind this study lies in adapting acoustic noise monitoring systems for road traffic monitoring for driver’s safety. Such a system should recognize a vehicle type and weather-related pavement conditions based on the audio level measurement. The study presents the effectiveness of the selected machine learning algorithms in acoustic-based road traffic monitoring. Bases of the operation of the acoustic road traffic...
-
Machine learning applied to acoustic-based road traffic monitoring
PublicationThe motivation behind this study lies in adapting acoustic noise monitoring systems for road traffic monitoring for driver’s safety. Such a system should recognize a vehicle type and weather-related pavement conditions based on the audio level measurement. The study presents the effectiveness of the selected machine learning algorithms in acoustic-based road traffic monitoring. Bases of the operation of the acoustic road traffic...
-
Further development of the poroelastic road surface within the new Polish project SEPOR
PublicationRoad surfaces have a direct impact on noise generated by rolling tyres, the main and dominant source of noise of moving vehicles. Road surface texture, porosity and stiffness/elasticity govern the pavement contribution to tyre/road noise the most. An experimental PoroElastic Road Surface (PERS) is a wearing course with a high content of interconnected voids (pores) and with an elastic behavior due to the use of small particles...
-
Comparison of pavement noise properties on selected road sections using different CPX measuring systems: self-powered vehicle and special test trailer
PublicationThe recently published ISO standard intended to measure the noise properties of road surfaces in a standardized method (ISO 11819-2:2017) precisely defines measurement procedure of the influence of road surface on traffic noise. According to it, two types of test vehicles may be utilized: a self-powered vehicle fitted with one or more test tyres and a trailer towed by a separate vehicle with one or more test tyres mounted on the...
-
Employing economical methods for pavement defects estimation
PublicationIt is a common practise that measurements of road surface conditions are made using professional and expensive apparatus. Typically a van or a truck equipped with a set of professional sensors i.e. laser scanners of surface is used, therefore the measurement update period is often quite long. Two alternative low-cost methods for estimating road pavement defects and failures were proposed and investigated by the authors. The first...
-
Impact of overloaded vehicles on load equivalency factors and service period of flexible pavements
PublicationOverloaded vehicles occur less frequently in comparison to properly loaded vehicles but due to their greater potential to cause damage they significantly contribute to the distress of pavement structure. As the studies show, the phenomena of vehicles overloading intensifies when the control of traffic is poor and the average percentage of overloaded vehicles on analyzed roads varies from 6% to 23%. The main goal of the ar-ticle...
-
Methods of deep modification of low-bearing soil for the foundation of new and spare air runways
PublicationAfter analyzing the impact of aircraft on the airport pavement (parking spaces, runways, startways), it was considered advisable to consider the problem of deep improvement or strengthening of its subsoil. This is especially true for low-bearing soil. The paper presents a quick and effective method of strengthening the subsoil intended for the construction of engineering structures used for civil...
-
Analysis of soundscape recordings in close proximity to the road in changeable wather conditions
PublicationThe acoustic vehicle sensing is the least invasive type of traffic detection. Also, acoustic-based vehicle detection technology is insensitive to precipitation and can operate in low light level. Therefore, this kind of method may be used for automatic detection of the vehicle passage events. It can also be employed for measurements of a vehicle speed and the vehicle assignment to the particular category. In this paper the results...
-
Review and evaluation of cold recycling with bitumen emulsion and cement for rehabilitation of old pavements
PublicationThe article presents Polish experience with cold recycling of asphalt pavements with theusage of bituminous emulsion and cement. In the 1990s numerous roads in Polandrequired immediate reinforcement due to their significant degradation. Implementation ofthe cold recycling technology was one of the solutions to this problem. Cold recycledmixtures containebeside the recycled asphalt pavement and aggregateetwo differenttypes of binding...
-
Bus bays inventory using a terrestrial laser scanning system
PublicationThis article presents the use of laser scanning technology for the assessment of bus bay geo-location. Ground laser scanning is an effective tool for collecting three-dimensional data. Moreover, the analysis of a point cloud dataset can be a source of a lot of information. The authors have outlined an innovative use of data collection and analysis using the TLS regarding information on the flatness of bus bays. The results were...
-
Road surface roughness estimation employing integrated position and acceleration sensor
PublicationAssessment of a surface quality being an essential task for the authorities supervising the roads provides the subject of the paper. Information about riding quality of a pavement, important for drivers, both in terms of their comfort and safety is collected during experiments employing mobile sensors. The paper describes the use of a miniature position and acceleration sensor for evaluation of the roughness of the road surface....
-
Decreasing CO2 Emissions By Reducing Tire Rolling Resistance
PublicationThe first motor vehicle was built by Nicolas Cugnot almost 250 years ago and since then there has been a continuous process of motor vehicles’ improvements, as well as development of new road pavements. The fuel crisis of the 70s of the 20th century made it clear to vehicle builders that measures should be taken to reduce vehicle fuel consumption and it contributed to an increased interest in electric vehicles. Although significant...
-
Cold recycled mixtures for binder courses - laboratory evaluation of mechanical properties
PublicationCold recycled mixtures composed with cement and bituminous emulsion are nowadays commonly used material for base layer. Typical pavement with cold recycled mixtures usually consists of two asphalt courses (wearing and binding course) constructed over cold recycled base. Therefore the next step in cold recycling is possibility of design of binding courses with recycled materials, but with potential to obtain high quality mixtures...
-
Engineering method of tire rolling resistance evaluation
PublicationTire rolling resistance is one of the most difficult tire parameters to measure. The reason is that for modern tires the force of rolling resistance corresponds to 0.5–1% of tire load, thus measurements of very small forces must be performed in a heavily loaded system. This constitutes great problems, especially in road conditions. Laboratory measurements are easier to perform, as the environment may be better controlled, but roadwheel...
-
The Influence of the Aircraft Operating Fluids on the Mechanical Parameters of the Airport Surface Concrete
PublicationThe authors of the article assessed the impact of operating fluids used to service aircraft on changing mechanical parameters of cement concrete intended for airport pavement. The research concerned concrete designed with the use of CEM I 42.5N LH NA low-alkali cement, broken granite aggregate, fine washed aggregate, and admixtures. The analysis included the assessment of changes in dierences in endurance parameters over various...
-
Application of Bayesian Networks in risk diagnostics arising from the degree of urban regeneration area degradation
PublicationUrban regeneration as a complex project, generates many extremely specific threats affecting the increase of investment risk. Its unique nature causes that probability parameter, normally applied in the process of risk quantification, is extremely difficult to estimate. Due to lack of historical data urban regeneration related activities are therefore associated with uncertainty. According to the authors, a useful tool for resolving...
-
Application of BN in Risk Diagnostics Arising from the Degree of Urban Regeneration Area Degradation
PublicationUrban regeneration as a complex project, generates many extremely specific threats affecting the increase of investment risk. Its unique nature causes that probability parameter, normally applied in the process of risk quantification, is extremely difficult to estimate. Due to lack of historical data urban regeneration related activities are therefore associated with uncertainty. According to the authors, a useful tool for resolving...
-
The application of the Superpave method of climatic zones analysis in Poland with regard to bitumen performance grading
PublicationCurrently in Poland, similarly as in the other EU countries, road bitumens are tested and classified with regard to mainly the penetration value determined at the tempera-ture of 25C. It should be noted that this classification is not correlated with the cli-matic conditions in which the bitumens are to serve in the road pavement. Towards the end of the last century a new system of bitumen grading was developed and im-plemented...
-
Tire/Road Noise On Poroelastic Road Surfaces - Results Of Laboratory Measurements
PublicationTire/road noise is the most important part of traffic noise for medium and high speed driving both in the case of passenger cars and trucks. The potential to make modification of tires that significantly reduce tire/road noise in nearly over, at least for conventional tires so the only promising action is to improve road pavements. One of the innovative solutions is poroelastic road pavement (PERS) that reduces airflow related...
-
Tyre rolling resistance and its influence on fuel consumption
PublicationRolling resistance of tyres is one of the major resistive forces acting on any wheeled vehicle. Unfortunately, it is also one of the forces very difficult to measure. It is estimated that in certain traffic conditions (like for example constant speed driving with slow or moderate speed) so called Rolling Resistance Impact Factor may be as high as 0.3. This means that reduction of rolling resistance by 50% would lead to 15% of energy...