Search
Filters
total: 521
filtered: 492
Search results for: TIRE RUBBER HARDNESS
-
Fabrication of exfoliated graphite reinforced silicone rubber composites - Mechanical, tribological and dielectric properties
PublicationThe effect of exfoliated graphite (EG) on the mechanical, tribological and dielectric properties of the silicone rubber (QM) composites has been systematically investigated and analysed. Morphological analysis of the composites helps to understand the interfacial interaction between the filler and the rubber matrix as well as wear mechanism respectively. An enhancement in the mechanical, tribological and dielectric properties was...
-
Microwave treatment in waste rubber recycling – recent advances and limitations
PublicationEnvironmentally-friendly microwave heating is increasingly used in polymer chemistry and technology. The selectivity and highly efficiency in the heat transfer present a huge advantage in systems based on recycling, improving their productivity and economic competitiveness. In case of the industrial recycling of waste rubbers, especially end-of-life tires, microwave-induced devulcanization and pyrolysis are nowadays considered...
-
Reclaimed Rubber/Poly(ε‐caprolactone) Blends: Structure, Mechanical, and Thermal Properties
PublicationThe amount of elastomeric waste, especially from tires is constantly increasing on a global scale. The recycling of these residua should be considered a priority. Compounding the waste rubbers with other polymers can be an excellent alternative to reuse waste materials. This procedure requires solving the issue of the lack of compatibility between the waste rubber particles and other polymers. Simultaneously, there is a claim for...
-
NUMERICAL ANALYSIS OF RUBBER BUMPERS INFLUENCE ON THE COLLIDING STEEL STRUCTURES
PublicationProblem of collisions of neighbouring structures is one of the important issues related to the safety of civil engineering structures. The safety and reliability of steel structures under impact loading is among a number of different aims during the design state. The aim of this paper is to present the results of numerical investigation of dynamic behavior of closely-separated steel structures under seismic excitation. Modal and transient...
-
Type of surface and tire rolling resistance
Publication...
-
Assessment of protective properties of rubber lining in absorbers of flue gas desulphurization systems.
PublicationResults of research on degradation of rubber lining which is the main protection of absorbers in flue gas desulphurization (FGD) systems were presented. The power plant where the system operated is lignite-fired. Owing to measurements using electrochemical impedance spectroscopy and gravimetric determination of water content in the lining, the areas of the system which are most exposed to degradation were shown. The results obtained...
-
Effect of glycolysate obtained from polyurethane wastes on mechanical properties of rubber materials
PublicationThe paper presents the possibility of utilization of wastes from polyurethane foams. In this work the results of mechanical investigations of materials obtained from natural rubber mixtures with a mixture of glycolysate and biodiesel glycerine as a plasticizer are described. The measurements of mechanical properties showed rather good tensile strength, elongation at break and modules of extensions M100%, M200%, M300% of obtained...
-
EXPERIMENTAL ANALYSIS OF RUBBER AND STYROFOAM BUMPERS INFLUENCE ON THE COLLIDING STRUCTURES
PublicationPast and recent investigations of colliding structures under seismic excitation confirmed that pounding may have a significant influence on the structural response. Interactions between adjacent buildings may cause serious damage to the structures, leading even to its total collapse. The main reason of earthquake-induced pounding, besides insufficient distance between structures, are differences in stiffness or mass of colliding structures....
-
Influence of free carbon on the Young's modulus and hardness of polymer‐derived silicon oxycarbide glasses
Publication -
The impact of laser surface treatment on the microstructure, wear resistance and hardness of the AlMg5 aluminum alloy
Publication -
Eco-friendly modification of bitumen: The effects of rubber wastes and castor oil on the microstructure, processability and properties
PublicationThe bitumen industry in the European Union is facing several difficulties, including rising demand, unstable oil supply, rising prices for synthetic polymer modifiers, and a focus on lowering carbon footprint. Bitumen modification with crumb rubber (CR) is one of the most promising solution to these challenges. However, CR-modified bitumen have poor processability and low storage stability. To overcome these flaws we are introducing...
-
The Effectiveness of Rubber Bumpers in Reducing the Effects of Earthquake-Induced Pounding between Base-Isolated Buildings
PublicationTh e methods for preventing earthquake-induced structural pounding between two adjacent buildings include ensuring a sufficient separation distance between them or decreasing their relative displacement during seismic excitation. Some equations or even specific values of such gap sizes between two buildings have been introduced so as to avoid collisions. Increasing the stiffness of buildings, using tuned mass dampers, applying...
-
Grafting and reactive extrusion technologies for compatibilization of ground tyre rubber composites: Compounding, properties, and applications
PublicationChemical modification of ground tyre rubber (GTR) to compatibilize it with the matrix is a well-known approach. Based on our recent review of the surface etching methods used in GTR modification, the purpose of the current work is to take a deeper look into more advanced methods such as grafting and reactive extrusion. While grafting is more efficient in achieving compatibility, however, it usually involves multi-step synthesis...
-
Temperature Measurements at Tyre Tread Rubber on Sandpaper Oscillatory Sliding Contacts Using Acicular Grindable Thermocouples
PublicationThe tribological performance of tyre–road contacts depends crucially on the contact temperature. This study investigates the reliability and accuracy of acicular grindable thermocouples possessing an original needle-shaped wearable part as applied to measuring temperature at the oscillatory sliding contact between a rubber tyre tread sample and a sandpaper. A linear oscillatory tribometer is used to imitate the sliding phase of...
-
Tire/road noise - generation, measurement, and abatement
PublicationPodano określenia i definicje dotyczące hałasu opon samochodowych. Omówiono mechanizmy generowania tego hałasu oraz zasady modelowania. Przedstawiono metody pomiaru hałasu opon oraz stosowane systemy pomiarowe. Podano normy dotyczące hałasu opon. Omówiono wpływ opony i nawierzchni na hałas generowany przez toczące się koło ogumione. Zaprezentowano koła kompozytowe oraz opony z bieżnikiem poroelastycznym generujące niski poziom...
-
High-density polyethylene/EPDM rubber blend composites of boron compounds for neutron shielding application
PublicationNovel materials with neutron shielding property were fabricated by incorporating boron compounds into highdensity polyethylene (HDPE)/Ethylene propylene diene monomer rubber (EPDM) blends. A detailed investigation on the morphological, thermal, mechanical, and neutron attenuation properties of suitable proportion of HDPE/EPDM blend with boric acid (BA), boron carbide (BC), and nano boron carbide (NBC) were performed. Morphology...
-
Chitin nanowhiskers from shrimp shell waste as green filler in acrylonitrile-butadiene rubber: Processing and performance properties
PublicationIn this work, chitin nanowhiskers with high crystallinity index were obtained from shrimp shells waste using acid hydrolysis method and then comprehensively characterized. Subsequently, the impact of chitin nanowhisker content on processing and performance of acrylonitrile-butadiene rubber based nanocomposites was evaluated. The results showed that the addition of chitin nanowhiskers increased tensile strength and tear strength...
-
FTIR spectroscopic and thermogravimetric characterization of ground tyre rubber devulcanized by microwave treatment
PublicationIn this work, the phenomena involved in the microwave devulcanization of ground tyre rubber (GTR) were investigated. Three types of GTR with different content of organic compounds (elastomers, plasticizers, etc.), carbon black and ash have been studied. The chemical structure of GTR before and after a microwave devulcanization process was analyzed by Fourier transform infrared spectroscopy (FTIR), thermogravimetric analysis (TGA)...
-
Effects of Basalt and Carbon Fillers on Fire Hazard, Thermal, and Mechanical Properties of EPDM Rubber Composites
PublicationDue to growing restrictions on the use of halogenated flame retardant compounds, there is great research interest in the development of fillers that do not emit toxic compounds during thermal decomposition. Polymeric composite materials with reduced flammability are increasingly in demand. Here, we demonstrate that unmodified graphene and carbon nanotubes as well as basalt fibers or flakes can act as effective flame retardants...
-
Effect of plasma sprayed and laser re-melted Al2O3 coatings on hardness and wear properties of stainless steel
PublicationCommercially available austenic stainless steel substrate was coated with commercially available, raw Al2O3 powder applied by means of plasma spraying method and then re-melted with CO2 laser beam of various parameters. Tribological and mechanical properties of the 120 J/mm and 160 J/mm laser re-melted coatings were compared with the tribological and mechanical properties of the “as-sprayed” coating. The influence of the laser...
-
Temperature-Based Prediction of Joint Hardness in TIG Welding of Inconel 600, 625 and 718 Nickel Superalloys
Publication -
Analysis of chemical composition and hardness of copper alloys = Badania składu chemicznego oraz twardości stopów miedzi
PublicationWykonano analizę składu chemicznego oraz badania twardości stopów miedzi zastosowanych na elementy łożyskowe. Sformułowano wnioski.
-
Complex Predictive Solution for Computerized Processes in Tire Industry
PublicationFollowing increasing market needs of productivity, cost reduction and safety requirements, computerized industry are faced to finding optimum between economic aspects of business and safety-related risk management. Modern factories equipped with computerized processes and extended diagnostic tools to support operator do not often use of all information’s which comes from the equipment. Some of the relations between the events are...
-
Cellulose Nanofibers Isolated from the Cuscuta Reflexa Plant as a Green Reinforcement of Natural Rubber
PublicationIn the present work, we used the steam explosion method for the isolation of cellulose nanofiber (CNF) from Cuscuta reflexa, a parasitic plant commonly seen in Kerala and we evaluated its reinforcing efficiency in natural rubber (NR). Fourier Transform Infrared Spectroscopy (FTIR), X-Ray Diffraction (XRD), Scanning Electron Microscopy (SEM), Transmission Electron Microscopy (TEM), and Thermogravimetric analysis (TGA) techniques...
-
Morphology and properties of recycled polyethylene/ground tyre rubber/thermoplastic poly(ester-urethane) blends
PublicationThe growing amount of plastics waste produced every year resulted in development of mechanical and chemical recycling methods of polymers and their blends or composites. From the environmental point of view, the possibility of plastics waste reusing and recycling is desirable. In this study three polymer blends were obtained with using recycled polyethylene (RPE), ground tyre rubber (GTR) and thermoplastic poly(ester-urethane)...
-
Synergistic effect of multi walled carbon nanotubes and reduced graphene oxides in natural rubber for sensing application
PublicationUtilizing the electrical properties of polymer nanocomposites is an important strategy to develop high performance solvent sensors. Here we report the synergistic effect of multi walled carbon nanotubes (MWCNTs) and reduced graphene oxide (RGO) in regulating the sensitivity of the naturally occurring elastomer, natural rubber (NR). Composites were fabricated by dispersing CNTs alone and together with exfoliated RGO sheets (thermally...
-
EVALUATING THE INFLUENCE OF BENDING STRESS ON A 1H18N9 STEEL SHAFT WEAR PROCESS IN A WATER LUBRICATED SLIDING BEARING WITH A RUBBER BUSHING
PublicationThe issue of excessive wear of shaft journals co-working with a rubber bearing has been unexplained so far. Premature and sometimes very intensive wear of ship sliding bearings in water conditions is the reason for carry out very expensive and more frequent than expected repairs. The authors (E. Piątkowska, W. Litwin) made an attempt to find a case that influences the value of this wear described in the paper “Attempt at Evaluating...
-
Determining the viscoplastic parameters of rubber-toughened plastics
PublicationW artykule omówiono szczegółowo zastosowanie sprężysto-lepkoplastycznego prawa Bodnera-Partoma do opisu zachowania się tworzywa sztucznego (kopolimer etylenowo-propylenowy). Parametry materiałowe ustalono na podstawie jednoosiowych testów jednoosiowego rozciągania. Proponowane podejście jest zilustrowane przykładami obliczeniowymi w programie MSC.Marc z wykorzystaniem procedury UVSCPL.
-
Monitoring of Rubber Belt Material Performance and Damage
Publication -
Fabrication of toughened plastic using styrene butadiene rubber-poly (methyl methacrylate) interpenetrating polymer networks
PublicationA standard set of interpenetrating polymeric networks (IPNs) has been contrived using an elastomerstyrene butadiene rubber and a thermoplastic poly (methyl methacrylate) through sequential polymerization protocol. This low-cost material can be hopefully engaged as a toughened plastic with cocontinuous morphology. Different morphological protocols including Raman imaging are effectively utilized to envisage the effect of blend ratio...
-
Waste printer ink as modifier for natural rubber/carbon black composites: No haste, use waste
PublicationFrom a sustainability perspective, achieving a greener future with a minimal carbon footprint requires maximizing waste materials' reuse. The four pillars of satisfying customer demands are processing, price, properties, and performance. Along with such a global policy, this work seeks to utilize waste printer ink (WPI) as a source of carbon in combination with low- and high-surface carbon black (LCB and HCB, respectively) additives...
-
Directivity of tire/road noise emission for selected tires and pavements
PublicationPraca pośwoęcona jest kierunkowości emisji hałasu opon i nawierzchni drogowych. Opony są dominującym źródłem haasu w pojaździe poruszającym się w typowych warunkach ruchu drogowego. Hałas ten nie jest bezkierunkowy jak to przyjmuje się w modelach obliczeniowych hałasu. Takie założenia wynikają z ograniczonej dostępności danych dotyczących kierunkowości i mogą prowadzić do niedokładności przy prognozowaniu hałasu drogowego. Praca...
-
The contribution of tire/road noise to the overal noise of cars and motocycles
PublicationOmówiono wływ hałasu opon i hałasu jednostki napędowej na całkowity hałas generowany przez pojazd. Zaprezentowano opracowany w Katedrze pojazdów i Maszyn Roboczych PG program VENOM do symulacji halasu pojazdów w ruchu drogowym. Przy pomocy tego programu określono wpływ zmiennych warunków ruchu drogowego na hałas generowany przez pojazd. Uwzględnioino przyspieszanie na poszczególnych biegach, hamowanie z różnymi prędkościami oraz...
-
ATTEMPT AT EVALUATING THE INFLUENCE OF BENDING STRESS ON SHAFT WEAR PROCESSES IN WATER LUBRICATED SLIDING BEARING WITH A RUBBER BUSHING
PublicationWater lubricated bearings find increasingly wide application in shipbuilding or hydro–power industry, the popularity stemming from their numerous advantages. Unfortunately, as it turns out, water lubricated bearings do not always meet expectations, as on occasion they become subject to intense, premature wear which requires costly repair. One of the still unexplained phenomena is the process of excessive bearing wear, in particular...
-
Experimental investigations on the mechanical properties and damage detection of carbon nanotubes modified crumb rubber concrete
PublicationThis study presents a modified crumb rubber (MCR) concrete design mix reinforced with multi-walled carbon nanotubes (MWCNTs), mechanical characterization, and cracking monitoring using the acoustic emission (AE) technique. The results showed that the bridging effect of MWCNTs and MCR in the concrete mix mitigated the shortcomings of MWCNT-MCR concrete and improved the flexural and compressive strengths by 18.3% and 26.5%, respectively,...
-
Inhomogeneity of low-noise wearing courses evaluated by tire/road noise measurements using the close-proximity method
PublicationPerforming numerous analyses of tire/road noise measurements on low-noise pavements during the last several years, the authors observed significant inhomogeneity of the wearing course in numerous cases, while similar problems were almost non-existent when dense pavements were measured. Three main causes of low-noise pavement inhomogeneity can be defined. The first one is imperfections in the technology used for asphalt mix production...
-
Thermal decomposition kinetics of dynamically vulcanized polyamide 6-acrylonitrile butadiene rubber-halloysite nanotube nanocomposites
PublicationThermally stable thermoplastic elastomer nanocomposites based on polyamide 6 (PA6), acrylonitrile butadiene rubber (NBR), and halloysite nanotubes (HNTs) were dynamically vulcanized, and their nonisothermal decomposition kinetics were examined. The Friedman, Kissinger–Akahira–Sunose (KAS), Ozawa–Wall–Flynn (FWO), and modified Coats–Redfern (m‐CR) isoconversional models were used to obtain information about the kinetics of the thermal...
-
Optimum shapes and dimensions of rubber bumpers in order to reduce structural pounding during seismic excitations
PublicationLarge displacement of structures observed during seismic excitations may lead to collisions between two adjacent, insufficiently-separated buildings and may result in major damages of both of them. In many building codes, appropriate equations or approximately recommended distances between structures in order to avoid pounding hazard have been introduced. Unfortunately, further, more detailed considerations show that safety situation...
-
Microstructure and Mechanical Properties of Carboxylated Nitrile Butadiene Rubber/Epoxy/XNBR-grafted Halloysite Nanotubes Nanocomposites
PublicationThe effect of various amounts of carboxylated nitrile butadiene rubber (XNBR) functionalized halloysite nanotubes (XHNTs) on the cure characteristics, mechanical and swelling behavior of XNBR/epoxy compounds was experimentally and theoretically investigated. The morphology of the prepared XNBR/epoxy/XHNTs nanocomposites was imaged using scanning electron microscopy (SEM). The effects of various XNBR-grafted nanotubes on the damping...
-
Experimental tests of water lubricated marine rubber bearing
PublicationW referacie przedstawiono stosowane obecnie rodzaje łożysk gumowych smarowanych wodą. Omówiono ich zalety i wady.W drugiej części pracy przedstawiono wyniki badań eksperymantalnych typowego okrętowego łożyska gumowego. Uzyskane rezultaty porównano z wynikami badań łożysk z polimerową panwią.
-
Non-linear model of high damping rubber bearing.
PublicationCelem artykułu jest analiza modelu łożyska wykonanego z wysokotłumiącej gumy, które wykorzystywane są do posadowienia konstrukcji budowlanych na terenach sejsmicznych. Model umożliwia numeryczną symulację pracy urządzenia pod zadanym obciążeniem i w danych warunkach termiczno-wilgotnościowych. Wyniki analizy pokazują, iż proponowany model umożliwia symulację zachowania się łożyska w szerokim zakresie odkształceń.
-
Certification of vehicles used for tire/road noise evaluation by CPX method
PublicationJednym ze sposobów oceny hałasu opon i nawierzchni drogowych jest metda CPX polegająca na pomiarze hałasu w polu bliskim miejsca współpracy opony z nawierzchnią. Aby uzyskać wysoką dokładność pomiarów niezbędne jest ustanowienie procedur ustanowienie procedur certyfikacyjnych sprzętu pomiarowego a więc głównie pojazdu badawczego. Praca dotyczy procedur certyfikacyjnych wypracowanych przez Grupę Roboczą WG33 ISO/TC43/SC1 oraz w...
-
Artificial neural network model of hardness, porosity and cavitation erosion wear of APS deposited Al2O3 -13 wt% TiO2 coatings
Publication -
The chemistry, properties and performance of flame-retardant rubber composites: Collecting, analyzing, categorizing, machine learning modeling, and visualizing
PublicationRubbers combine the flexibility with mechanical strength, supporting myriad applications, but suffer from inherent flammability. Formulation and production of flame-retardant rubber composites (FRRCs) have intensively been practiced over years, but not comprehensively reviewed. This necessity has outlined collecting, analyzing, screening, classifying, and interpreting the literature with the aim of classifying the FRRCs. We quantified...
-
Weather aging effects on modified asphalt with rubber-polyethylene composites
Publication -
Inspection of rubber linings operating in flue gas desulphurisation units
Publication -
The effect of mercerized sisal fibres on natural rubber composites' properties
PublicationW pracy omówiono wyniki badań fizyko-mechanicznych kompozytów otrzymanych z mieszanek zawierających kauczuk naturalny oraz statystycznie zdyspergowane krótkie włókno sisalowe. Włókno naturalne przed użyciem poddano merceryzacji.Otrzymane wulkanizaty poddano badaniom wytrzymałościowym w warunkach statycznych w celu określenia wpływu parametrów wulkanizacji i ilości dodanego włókna na właściwości otrzymanych produktów. Stwierdzono...
-
Nonlinear rate dependent model of high damping rubber bearing.
PublicationCelem artykułu jest analiza nieliniowego modelu łożyska wykonanego z wysokotłumiącej gumy, który symuluje pracę urządzenia pod zadanym obciążeniem. Parametry modelu dobrane są na podstawie wyników badań eksperymentalnych. Wyniki pracy pokazują, iż analizowany model umożliwia symulację zachowania się łożyska w szerokim zakresie odkształceń
-
Advancing sustainable hybrid bitumen systems: A compatibilization solution by functionalized polyolefins for enhanced crumb rubber content in bitumen
PublicationPolymer waste pollution has a profound effect on the environment and, consequently, on the lifestyle of hu- mankind. The massive production and disposal of cross-linked polymers clearly exemplify the challenges of recycling. Increasing efforts are being undertaken to introduce recycled polymers, especially crumb rubber (CR), into asphalt formulations. Due to the rather poor processability and phase separation associated with CR- modified...
-
Alkali-activated slag (AAS) and OPC-based composites containing crumb rubber aggregate: Physico-mechanical properties, durability and oxidation of rubber upon NaOH treatment
Publication