displaying 1000 best results Help
Search results for: NOTCHED SPECIMEN
-
Fracture surface topography investigation and fatigue life assessment of notched austenitic steel specimens
PublicationThe objectives of this study were to investigate the fracture surface topography of X8CrNiS18-9 austenitic stainless-steel specimens for different loadings and notch radii and to supplement the knowledge about the fracture mechanisms for fatigue performance. Cases with three different values of the notch radius ρ and the stress amplitude σa were analysed. The fracture topographies were quantified by the areas over their entire...
-
Post-failure fracture surface analysis of notched steel specimens after bending-torsion fatigue
Publication -
The fracture behaviour of notched PMMA specimens under simple loading conditions – Tension and torsion experimental tests
PublicationThis paper presents the results of experimental testing of flat PMMA specimens during uniaxial loading conditions. Two separate tests were conducted: tensile and torsion. The specimens were weakened with V-type edge notches with different root radii: 0.5; 2 and 10 mm. The specimens were made in two thickness variants: 5 and 15 mm. Monotonic tensile and torsion tests were carried out while keeping the averaged strain rate constant,...
-
The experimental and numerical investigation of fracture behaviour in PMMA notched specimens under biaxial loading conditions – Tension with torsion
PublicationThis paper presents the results of experimental fracture test of flat PMMA specimens under biaxial loading condition tension with torsion (proportional). The specimens were made in two thicknesses: 5 and 15 mm and were weakened with V-type edge notches with different root radii: 0.5; 2 and 10 mm. Thanks to the ARAMIS 3D 4 M non-contact vision system, measurement of the elongation and twist angle were recorded. During experimental...
-
The elasto-plastic numerical study of crack initiation in notched PMMA specimens under uniaxial loading conditions – Tension and torsion
PublicationThis paper presents the results of FEM numerical calculations aimed at describing the plastic strain and stress fields under critical loading conditions: tensile force or torsional moment. The calculations were carried out with reference to the results of experimental tensile and torsional tests of flat PMMA specimens weakened with V-notches of different root radii: 0.5, 2 and 10 mm. The procedure for conducting nonlinear numerical...
-
Fracture prediction in flat PMMA notched specimens under tension - effectiveness of the equivalent material concept and fictitious material concept
PublicationThe fracture of notched elements under mode I loading (tension) remains an inexhaustible research topic, especially when it comes to the fracture of thermoplastic materials such as polymethylmethacrylate (PMMA), which experience considerable plastic strains under tension. The paper points out that traditional brittle fracture criteria such as mean stress (MS) or maximum tangential stress (MTS) criteria used to predict this phenomenon do...
-
Numerical investigations of size effects in notched and un-notched concrete beams under bending
PublicationW artykule przedstawiono wyniki numerycznej analizy efektów skali (efektu deterministycznego i stochastycznego) w belkach betonowych z nacięciem i bez nacięcia poddanych zginaniu z uwzględnieniem lokalizacji odkształceń. Obliczenia wykonano przy zastosowaniu metody elementów skończonych i sprężysto-plastycznego modelu z nielokalnym osłabieniem. Pokazano wpływ wielkości belek betonowych na ich nośność oraz rozkład lokalizacji odkształceń.
-
Fatigue Bending of V-Notched Cold-Sprayed FeCoCrNiMn Coatings
PublicationCold-spray coatings were produced by FeCoCrNiMn high-entropy alloy powders deposited on carbon steel substrate. The coatings were realized at intermediate temperature and high pressure (at 1100 °C and 7 MPa). The coating microstructure was characterized by scanning electron microscopy and X-ray diffraction, revealing a very dense deposition and high flattening ratio of the splatted particles. This had a large influence on the...
-
Standard and modified falling mass impact tests on preplaced aggregatefibrous concrete and slurry infiltrated fibrous concrete
PublicationAlthough several studies have been conducted to evaluate the impact response of concrete using theAmerican Concrete Institute (ACI) 544-2R falling mass impact test, the variations in test results are themain drawback of this testing method. This study aims to reduce the variations in experimental impacttest results by introducing two simple test setup modifications; (1) using coarse or fine aggregate bed-ding as an alternative...
-
Species Diversity
Journals -
Measurements and calculations of the width of the fracture process zones on the surface of notched concrete beams
PublicationArtykuł omawia wyniki pomiaru i analizy numerycznej szerokości strefy pękania w belkach betonowych z nacięciem. Do pomiarów zastosowano metodę DIC. Do symulacji zastosowano model sprężysto - plastyczny i model z degradacją sztywności. Oba modele zostały rozszerzone o nielokalne osłabienie. Wyniki symulacji porównano z doświadczeniami.
-
Fracture surface formation of notched 2017A-T4 aluminium alloy under bending fatigue
PublicationThe effect of cyclic loading on facture surface topology in notched components made by aluminium alloys is not completely clear. Fractogra-phy and fracture mechanics can help to understand this interdependency. This paper aims to study the distribution of the fracture surface roughness of notched 2017A-T4 aluminium alloy after bending fatigue using an optical focus-variation surface measurement technique by applying the fracture...
-
Multiaxial fatigue life assessment in notched components based on the effective strain energy density
Publication -
Silent Sonar with matched filtration
PublicationRadars with continuous wave frequency (CW FM sonars) are used in radiolocation as 'silent sonars'. They determine the distance to target by measuring the difference between the frequency of the sounding signal and echo signal. The article presents the principle of operation and parameters of silent CW FM sonars. Target distance determined by these sonars is based on the signal at the output of the matched filter. The Doppler effect...
-
Unstability of 4-CMC in human serum specimen
Publication -
Instrumented End Notched Flexure - Crack propagation and process zonemonitoring. Part I: Modelling and analysis
PublicationAnalysis of the three-point bending, End Notched Flexure (ENF), test is presented for exploitation with a new experimental methodology using the backface strain monitoring technique. The model consists oftwo Timoshenko beams joined with a two parameter elastic foundation, to evaluate stress and strain fields in both adherends and the adhesive layer, together with the specimen compliance and energyrelease rate. This model is compared...
-
Endangered Species Research
Journals -
PLANT SPECIES BIOLOGY
Journals -
Instrumented end notched flexure - Crack propagation and process zonemonitoring Part II: Data reduction and experimental
PublicationA mode II instrumented end notched flexure three point bending (ENF) adhesion test is described. The adhesive joint consists of two aluminium alloy (AW7075-T6) plates bonded with a structural epoxy adhesive (Hysol EA 9395™). Strain gauges are attached to the outer surface (backface) of the substrates in the lengthwise direction to measure local surface strain during crack propagation. Simultaneously, load/displacement measurements...
-
Calculations of fracture process zones on meso-scale in notched concrete beams subjected to three-point bending.
PublicationW artykule przedstawiono wyniki numeryczne MES modelowanie belek betonowych z nacięciem na poziomie skali mezo. Beton został opisany na poziomie skali mezo jako stochastyczny materiał 3-składnikowy złożony z kruszywa, zaczynu cementowego oraz stref kontaktu. Obliczenia wykonano przy wykorzystaniu modelu degradacji sztywności z nielokalnym osłabieniem. Zbadano wpływ stochastycznego rozkładu kruszywa, średnicy, kształtu oraz zagęszczenia...
-
Fractographic-fractal dimension correlation with crack initiation and fatigue life for notched aluminium alloys under bending load
PublicationIn this study, fatigue fracture surfaces of aluminium alloy 2017-T4 notched specimens were investigated under cyclic bending to find an alternative failure loading index.. The surface topographies were measured on the entire fracture area with an optical profilometer for different loading conditions. Fatigue crack initiation life Ni and total fatigue life Nf were examined using standard surface topography parameters (such as, root...
-
FE analysis of support-specimen interaction of compressive experimental test
PublicationThe objective of this work is to investigate the support-specimen interaction during the compressive experimental testing of stiffened plates. The interaction is analyzed employing the nonlinear Finite Element Method using the commercial software ANSYS. The connection between the stiffened plate and testing supports is modelled with the use of contact elements, where several possible interaction scenarios are investigated, and...
-
Fatigue life prediction of notched components under size effect using strain energy reformulated critical distance theory
PublicationNotch and size effects show significant impact on the fatigue performance of engineering components, which deserves special attention. In this work, a strain energy reformulated critical distance theory was developed for fatigue life prediction of notched components under size effect. Experimental data of different notched specimens manufactured from GH4169, TC4, TC11 alloys and low carbon steel En3B were used for model validation...
-
Effect of non-zero mean stress bending-torsion fatigue on fracture surface parameters of 34CrNiMo6 steel notched bars
Publication -
Notched concrete beams under bending - calculations of size effects within stochastic elasto-plasticity with non-local softening
PublicationW artykule przedstawiono wyniki numerycznej analizy efektów skali (efektu deterministycznego i stochastycznego) w belkach betonowych nacięciem poddanych zginaniu z uwzględnieniem lokalizacji odkształceń. Obliczenia wykonano przy zastosowaniu metody elementów skończonych i sprężysto-plastycznego modelu z nielokalnym osłabieniem. Pokazano wpływ wielkości belek na nośność z uwzględnieniem stochastycznego rozkładu wytrzymałości na...
-
Numerical simulation of laminate composite specimens failure
PublicationThis work presents some numerical results concerning simulation of failure of laminate composite specimens. In the article two tests to determine ultimate strength in an orthotropic layer, are considered: tension (TT1) and compression (TC1) test. The outcome is compared with experimental data provided by [9,10].
-
Comparison of different one-parameter damage laws and local stress-strain approaches in multiaxial fatigue life assessment of notched components
PublicationThis paper aims to compare the predictive capabilities of different one-parameter damage laws and local stress-strain approaches to assess the fatigue lifetime in notched components subjected to proportional bending-torsion loading. The tested fatigue damage parameters are defined using well-known stress-based, strain-based, SWT-based and energy-based relationships. Multiaxial cyclic plasticity at the notch-controlled process zone...
-
Comparison of different one-parameter damage laws and local stress-strain approaches in multiaxial fatigue life assessment of notched components
Publication -
Optical flow method for measuring deformation of soil specimen subjected to torsional shearing
PublicationIn this study optical flow method was used for soil small deformation measurement in laboratory tests. The main objective was to observe how the deformation distributes along the whole height of cylindrical soil specimen subjected to torsional shearing (TS test). The experiments were conducted on dry non-cohesive soil specimens under two values of isotropic pressure. Specimens were loaded with low-amplitude cyclic torque to analyze...
-
Dynamic hand-written signature verification using a matched filter
PublicationW pracy zaproponowano nowe podejście do weryfikacji dynamicznego podpisu odręcznego. Podpis jest traktowany jako sygnał telekomunikacyjny, który można wykryć i zwerfikować za pomocą odbiornika optymalnego z filtrem dopasowanym. Wymaga to uprzedniej unifikacji i normalizacji parametrów biernych podpisu aktualnego, jak również podpisów zgromadzonych w bazie, celem ułatwienia podejmowania decyzji. Normalizację długości podpisu uzyskano...
-
Influence of Wood Moisture on Strength and Elastic Modulus for Pine and Fir Wood Subjected to 4-point Bending Tests
PublicationThe main purpose of this research paper was to determine the influence of the wood moisture on the strength and elastic modulus of pine and fir wood specimens subjected to the 4-point bending tests. Six bending tests for each wood species and for two different moisture level have been performed. Then, the advanced statistical analysis of the results has been carried out. On the basis of the obtained results, it has been noted that...
-
Generalized adaptive notch smoothing revisited
PublicationThe problem of identification of quasi-periodically varying dynamic systems is considered. This problem can be solved using generalized adaptive notch filtering (GANF) algorithms. It is shown that the accuracy of parameter estimates can be significantly increased if the results obtained from GANF are further processed using a cascade of appropriately designed filters. The resulting generalized adaptive notch smoothing (GANS) algorithm...
-
New Algorithms for Adaptive Notch Smoothing
PublicationThe problem of extraction/elimination of a nonstationary complex sinusoidal signal buried in noise is considered. This problem is usually solved using adaptive notch filtering (ANF)algorithms. It is shown that accuracy of signal estimation can be increased if the results obtained from ANF are further processed using a cascade of appropriately designed filters. The resulting adaptive notch smoothing (ANS) algorithms can be employed...
-
Chemometrics of bi-heterocyclic kind of drug specimens in the THz domain
Publication -
Distance measurement errors in silent FM-CW sonar with matched filtering
PublicationThe secretiveness of sonar operation can be achieved by using continuous frequency-modulated sounding signalswith reduced power and significantly prolonged repeat time. The application of matched filtration in the sonarreceiver provides optimal conditions for detection against the background of white noise and reverberation, and avery good resolution of distance measurements of motionless targets. The article shows that target...
-
Antimicrobial activity of Potentilla species
Publication -
Influence of the notch rounding radius on estimating the elastic notch stress concentration factor in a laser welded tee joint
PublicationIn recent years an increased interest of industry in sandwich-type metal structures can be observed. These structures consist of thin plates of 2.5 mm in thickness separated by stiffeners of different shapes and forms. Welds joining the plates and stiffeners are made on the outer side of the plates using laser welding technique. A locally focused source of heat causes the plate to melt creating a very narrow and elongated joint....
-
Three-Dimensional Fractography for Conventional and Additive Manufactured Steels After Bending-Torsion Fatigue
PublicationIn this study, fracture surface topography parameters were measured to investigate the effects of multiaxial loading. In order to assess the metrological aspects of fracture for notched specimens made of high-strength steels processed by both conventional and additively manufacturing (AM) techniques, an optical surface profilometer was used. Three bending moment to torsion moment ratios (B/T) were studied, i.e. 2, 1 and 2/3. The...
-
Herbarium of Division of Marine Biology and Ecology University of Gdańsk (DMBE)
Open Research DataHerbarium of Division of Marine Biology and Ecology University of Gdańsk (DMBE) is a research herbarium encompassing specimens of vascular plants and algae hosted by the Laboratory of Marine Plant Ecology at University of Gdańsk, Poland. The aim of Herbarium is to preserve marine plant and algae collections mostly from the Gulf of Gdańsk, but the herbarium...
-
EXPERIMENTAL AND NUMERICAL INVESTIGATION ON SPECIMEN GEOMETRY EFFECT ON THE CTOD VALUE FOR VL-E36 SHIPBUILDING STEEL
PublicationThere are special cases in the marine industry, where additional material tests, such as the fracture toughness test, must be performed. Additional fracture toughness tests, such as CTOD (Crack Tip Opening Displacement), are typically performed on three-point bend specimens. The dimension that defines all the specimen dimensions is the thickness of the material to be tested. It is recommended by classification societies (e.g. DNVGL)...
-
Tracking analysis of a generalized adaptive notch filter
PublicationUogólniony adaptacyjny filtr wycinający służy do identyfikacji obiektów zmieniających się w sposób pseudookresowy. W pracy przedstawiono analizę własności śledzących takiego filtru a także omówiono zasady jego strojenia.
-
BUILT IN PERFORMANCE EVALUATION FOR AN ADAPTIVE NOTCH FILTER
PublicationThe problem of estimating instantaneous frequency of a non- stationary complexsinusoid (cisoid) buried in wideband no ise is considered. The proposed approach extends adaptive notc h filtering algorithm with a nontrivial performance assessme nt mechanism which can be used to optimize frequency tracking performance of the adaptive filter. Simulation results confi rm that the proposedextension allows one to improveaccuracyo f frequency...
-
Effect of elliptical defect orientation on the durability of specimens subjected to cyclic bending
PublicationThis work presents the effect of elliptical defects orientation on the durability of specimens made of C45 steel. Three kinds of specimens with elliptical defects in the form of a one-sided notch oriented at different angles 45, 60, and 90 degrees were subjected to cyclic bending (R=-1). The stress state analysis was performed using local and non-local methods to determine an equivalent amplitude of stress, and then the results...
-
Analysis of magnetic signals of vehicles aided by matched filtering with FPGA FFT processor
PublicationW artykule przedstawiono system analizy i identyfikacji pojazdów oparty na pomiarze indukcji magnetycznej. Do tego celu jest stosowany zestaw czujników magnatycznych pracujących bezprzewodowo, który pozwala na monitorowanie ruchu pojazdów na lotniskach, w potrach i punktach kontroli granicznej. System taki może być zastosowany do wykrywania i identyfikacji pojadów zawierających elementy ferromagnetyczne, które zaburzają pole magnetyczne...
-
Development of a digital method for neutron/gamma-ray discrimination based on matched filtering
Publication -
Localization of impulsive disturbances in archive audio signals using predictive matched filtering
PublicationThe problem of elimination of impulsive disturbances from archive audio signals is considered and its new solution, called predictive matched filtering, is proposed. The new approach is based on the observation that a large percentage of noise pulses corrupting archive audio recordings have highly repetitive shapes that match several typical “patterns”, called click templates. To localize noise pulses, click templates can be correlated...
-
Measurement of magnetic signals of vehicles with denoising by matched filtering with FPGA FFT processor
PublicationW artykule przedstawiono realizację systemu do analizy i identyfikacji pojazdów oparty na pomiarze indukcji magnetycznej. Proponowany system może być zastosowany do wykrywania i identyfikacji pojadów zawierających elementy ferromagnetyczne, które zaburzają pole magnetyczne ziemi. Zaburzenie to można zmierzyć przy zastosowaniu trójosiowych magnetometrów transduktorowych, pracującyh w układzie różnicowycm. Zastosowano w systemie...
-
Experimental study of the impact of notches and holes made in the front edge of adherends on the properties of static and fatigue strength of adhesive joints
PublicationThe paper presents the results of experimental studies aimed at determining the effect of holes and notches at the front edge of adherends on the strength of adhesive joints. Single-lap joints made of S235JR steel sheets joined with Araldite 2014-2 epoxy adhesive were tested. Comparative tests of static strength in the shear test as well as high-cycle fatigue strength tests were carried out. Joints with three holes with a diameter...
-
Heptaene macrolides biosynthesis by Streptomyces species
PublicationPolyene macrolides are one of the groups of secondary metabolites, generated by microorganisms belonging to the Streptomyces genus. These compounds, containing 3 - 7 conjugated double bonds systems in their molecules exhibit high antifungal activity against a broad spectrum of fungal pathogens with heptaenes demonstrating the highest antifungal potential. At the large extent, efficiency of biosynthesis of these natural products...
-
Species in the wild: a typology of innovation ecosystems
Publication