Filters
total: 3143
-
Catalog
displaying 1000 best results Help
Search results for: SERVO-LAYER
-
Servo tracking of targets at sea
PublicationW artykule przedstawiono propozycje systemu sterowania układem śledzącym umieszczonym na okręcie. Przedstawiono dynamikę błędów śledzenia obiektu we współrzędnych LOS (ang., Line - Of - Sight). Zostało wykazane, że regulacja błędów śledzenia LOS jest możliwa przy pomocy sprzężenia feed-forward od prędkości śledzonego obiektu. Ponieważ prędkość ta nie jest mierzalna zastosowano filtr Kalmana w celu jej estymacji. Ponieważ problem...
-
Fuzzy logic gain scheduling for non - linear servo tracking
PublicationArtykuł zawiera propozycję strojenia jako metodę sterowania serwomechanizmem z silnie nieliniowymi elementami. Serwomechanizm steruje dwoma elementami układu śledzącego zamontowanymi na okręcie znajdującym się w morzu. W układzie występuje tarcie spoczynkowe przy zerowej prędkości oraz nieliniowe tarcie przeciwdziałające ruchowi w każdej z osi układu śledzącego. Zastosowany został podwójny układ sterowania ze sprzężeniem zwrotnym....
-
Temperature distribution in laser-clad multi-layers
Publication -
Temperature distribution in laser-clad multi-layers
PublicationW pracy przedstawiono porownanie rezultatów numerycznej symulacji rozkładu temperatur w warstwach nakładanych laserowo z wynikami pomiarów doświadczalnych. Otrzymano bardzo dobrą zgodność wyników co pozwala wnioskować, że przedstawiony model numeryczny może służyć jako efektywne narzędzie wstępnego doboru parametrów procesu laserowego nakładania warstw.
-
Influence of laser melting on surface layer properties of titanium alloy Ti6Al4V
PublicationIn time of rapid technology and medicine progress, implants are becoming more widely used in the human body, ranging from dental implants, stabilizing plates, screws, orthopaedic prostheses. For example, there are many types of hip prostheses used for hip replacement as well as various types of materials used for these orthopaedic prostheses. Properties of titanium alloys used in hip prostheses combined with good strength properties,...
-
Microstructure and wear of cast aluminium alloy with laser modified surface layer
Publicationprzedstawiono wyniki badań zużycia przez tarcie przetopionego laserowo stopuAlSi13MgCuNi w warunkach tribologicznych. Wykazano, iż zużycie i współczyn-nik tarcia są zależne od parametrów obróbki laserowej w warunkach kriogeni-cznych.
-
The phase composition of the surface layer of laser melted Ti-6Al-4V bioalloy
PublicationZastosowanie metody obróbki laserowej stopów Ti zwiekszyły twardość i odporność stopu na korozję. Jednakże uzyskane warstwy były stosunkowo cieńkie. W pracy zastosowano laser o dużej mocy dla stopu schłodzonego w ciekłym azocie, aby uzyskać grubszą warstwę, która w strefie zewnętrznej złożona będzie z tlenku i azotku tytanu, ważnych faz w biostopach.
-
Influence of Laser Treatment on Microstructure of Surface Layer of the Ti-6Al-4V Alloy
PublicationPrzedstawiono mikrostrukturę powierzchni, przekroju i przełomu warstwy wierzchniej stopu Ti-6Al-4V uzyskanej po nadtapianiu laserem w różnym środowisku. Stwierdzono wzrost mikrotwardości stopu w warstwie nadtopionej, rozdrobnienie ziarna, a także tworzenie azotków tytanu i mikropęknięć skutkiem obecności znacznych naprężeń własnych. Grubość wytworzonych warstw osiągała wartość 1,5 mm.
-
Laser assisted forming of the surface layer of Al-Si alloy at cryogenic conditions.
PublicationW artykule przedstawiono wpływ powierzchniowego laserowego przetapiania w warunkach kriogenicznych na mikrostrukturę, mikrotwardość i własności korozyjne stopu AlSi13Mg1CuNi. Stwierdzono korzystny wpływ obróbki laserowej na mikrostrukturę, mikrotwardość i odporność na zużycie ścierne badanego stopu aluminium.
-
Space vector modulation in multilevel inverters of the servo drives of the trajectory measurements telescopes
PublicationUsing the MatLab/Simulink mathematical model of a three-phase three-level voltage inverter, the influence of the space-vector modulation (SVM) algorithm on the pulsations of the current (torque) of an AC motor in the range of low rotation speeds is considered. It is shown that the SVM of the second kind does not provide a pulsations level comparable to the pulsations of a sinusoidal pulse-width modulation (SPWM), both in the static...
-
The computer numerical control system with permanent magnet synchronous motor servo-drives.
PublicationPrzedstawiono układ serwonapędów wieloosiowej maszyny sterowanej numerycznie. W układzie wykorzystano silniki synchroniczne z magnesami trwałymi oraz procesory synałowe DSP. Omówiono algorytmy sterowania nadrzędnego oraz problemy sterownia silnika PMSM.
-
Characterization of the Co-base layers obtained by laser cladding technique.
PublicationBadano zawory wydechowe napawane dwoma stopami kobaltu, w tym mikrostrukturę strefy wierzchniej i strefy w pobliżu podłoża. Badano także rozkład pierwiastków w warstwie napawanej. Stwierdzono podobny skład chemiczny warstw i proszków.
-
Characterization of the Co-base layers obtained by laser cladding technique.
PublicationBadano zawory wylotowe pokrywane stopami kobaltu: mikrostrukturę warstw w strefie wierzchniej i przy granicy napoina - metal. Badano rozkład pierwiastków w warstwach. Zarówno mikrostruktura, jak i skład chemiczny warstw były podobne w przypadku dwóch stosowanych stopów kobaltu.
-
Wear Resistance Enhancement of Al6061 Alloy Surface Layer by Laser Dispersed Carbide Powders
PublicationIn this paper, results of the experimental study on improving wear resistance in sliding friction of Al-based alloy are presented. The technique used involves the formation of a metal matrix composite (MMC) in the alloy surface layer by laser dispersion of carbide powders such as WC, TiC and SiC. For WC and TiC MMC surface coatings fabricated under conditions typical for most of the technologically relevant solid-state lasers (wavelength...
-
The influence of laser alloying on the structure and mechanical properties of AlMg5Si2Mn surface layers
Publication -
Surface layers analysis of bronze artifacts by means of laser spectroscopy techniques
Publication.
-
Morphology studies of the cobalt base clad layers produced by laser technology.
PublicationPrzedmiotem badań były utwardzające warstwy wykonane na przylgni zaworów wydechowych silnika spalinowego. Materiał podłoża to stal H10S2M. Zastosowano technologię napawania laserowego proszków na bazie kobaltu. Proszki różniły się jedynie zawartością wolframu i zawierały odpowiednio 4,9; 5,3 i 9 wg% tego pierwiastka. Parametry napawania były jednakowe dla wszystkich proszków. Otrzymane warstwy różniły się twardością na powierzchni...
-
On the Microstructure, Microhardnessand Wear Behavior of Gray Cast Iron Surface Layer after Laser Strengthening
Publication -
Formation of surface layer in metal matrix composite A359/20SiCP during laser assisted turning
Publication -
Ordered titania nanotubes layer selectively annealed by laser beam for high contrast electrochromic switching
PublicationThe phase conversion from amorphous into crystalline one in the selected area of as-anodized titania nanotubes was achieved via laser treatment. The optimized processing parameters enable fast, one-minute crystallization of titania within an area limited by a shadow mask and without any morphology damage of ordered TiO2 tubular film. The laser annealed titania nanotubes could be easily overgrown by a conducting polymer without...
-
The new SDMT-family of servo-drives for CNC systems with AC permanent magnet synchronous motors
PublicationW artykule przedstawiono strategię sterowania podstawowe parametry oraz wyniki badań nowej rodziny serwonapędów typu SDMT. Układ sterowania serwonapędu zbudowano na procesorze sygnałowym TMS320F2812 firmy Texas Instruments. W serwonapędzie zastosowano metodę sterowania tupu FOC (ang. Field Oriented Control). Regulatory położenia, prędkości i momentu zreali-zowano na bazie klasycznego regulatora PID z układem ograniczenie sygnału...
-
Neutral point balancing technique for 3-level neutral point clamped converter with servo system
PublicationNeutral point voltage drift compensation technique in 3-level NPC multilevel converter and servo system is described in the paper. Analytical expressions are obtained for power subsystem elements parameters of servo drive system. Simulation of servo system, based on PMSM motor with 3-level NPC converter is considered.
-
Mutual recognition of certification systems: The case of SERMO and ACLES
Publication -
Surface Layer Properties of Sintered Ferritic Stainless Steel Remelted and Alloyed with FeNi and Ni by HPDL Laser
Publication -
Structure and Mechanical Properties of Composite Layers Prepared by Laser Alloying of Aluminium Alloy
Publication -
Properties of surface layers of titanium alloy Ti6Al4V after laser melting processes
PublicationThe article presents the investigation results of titanium alloy Ti6Al4V surface layer after laser melting process. The process of laser melting was performed using Nd-YAG laser. The evaluation of structure of the alloy as well as hardness and chemical composition was performed. It was shown that laser melting changes the structure and properties of titanium alloy Ti6Al4V and process parameters as scanning speed affects the thickness...
-
BOUNDARY-LAYER METEOROLOGY
Journals -
Ayer
Journals -
Funkcialaj Ekvacioj-Serio Internacia
Journals -
Investigation of thin perovskite layers between cathode and doped ceria used as buffer layer in solid oxide fuel cells
PublicationIn this paper, thin perovskite layers between cathode material of solid oxide fuel cells and gadolinia-doped ceria buffer layer are investigated. Thin layers made of LaNi0.6Fe0.4O3-δ (LNF), La0.6Sr0.4Co0.2Fe0.8O3-δ (LSCF), or SrTi0.65Fe0.35O3-δ (STF) were symmetrically deposited by spin coating method from metallo-organic polymer precursors on a Ce0.8Gd0.2O2-δ (CGO) substrate. Porous and about 40-μm-thick LNF cathodes were deposited...
-
Effect of hybrid modification by ceramic layer formation in MAO process and laser remelting on the structure of titanium bio-alloy Ti13Nb13Zr
PublicationTo improve the biological properties of titanium alloy Ti13Nb13Zr, hybrid modifications involving micro-arc oxidation (MAO) and Nd: YAG laser remelting were carried out in two combinations. The first consisted of laser modification before the production of the ceramic layer by the micro-arc oxidation process, and the second combination involved Nd: YAG laser modification after the MAO process. The creation of developed surface...
-
Influence of the laser remelting parameters on the thickness of surface layers created on the stainless steel X5CrNi18-10
PublicationIn this work the surface of austenitic stainless steel type X5CrNi18-10 was treated by using laser. Laser remelting was done by means of laser MLT 2500 CO2 with different parameters of treatment: P - power beam (800 [W], 1000 [W], 1100 [W], 1200 [W]); v - scanning velocity (6 [mm/s], 7 [mm/s], 8 [mm/s]); diameter of laser beam (1.4 [mm], 1.6 [mm]). The influence of these parameters on the thickness and shape of layers in manufacturing...
-
Spectral reflectance modeling of ZnO layers made with Atomic Layer Deposition for application in optical fiber Fabry-Perot interferometric sensors
PublicationSuitability of zinc oxide (ZnO) layers grown using Atomic Layer Deposition for operation in optical-fiber extrinsic Fabry-Perot sensors is investigated using a numerical model. Reflectance spectra obtained using the developed model indicate that the application of these layers in optical-fiber extrinsic Fabry-Perot sensors is difficult as it may require a source whose spectrum width is about 300 nm. A series of ZnO layers grown...
-
BUSINESS LAWYER
Journals -
Laser Therapy
Journals -
Lawyer Quarterly
Journals -
International Lawyer
Journals -
URBAN LAWYER
Journals -
The importance of the bottom layer in double-layer porous asphalt for noise reduction
PublicationDouble-layer porous asphalt concrete (DPAC) surfaces are generally considered to be the acoustically most effective low noise road surfaces ready for implementation. While DPAC used on highways in warm climates may have an average life of around 8 years, in Scandinavia with severe winter climate DPAC usually survive only about 3 years; partly due to wear of studded tyres. An ongoing project in Sweden, applying DPAC and single-layer...
-
Layer-by-layer polymer deposited fabrics with superior flame retardancy and electrical conductivity
PublicationSmart and multifunctional textiles and fabrics are progressively developing, such that multifunctional fabrics are becoming more widespread. We elaborated herein multi-layered flax fabrics with superior flame retardancy and conductivity, which revealed fireproof feature while keeping conductivity during burning. The flax fabric was reinforced by layer-by-layer (LbL) deposition of sodium polyacrylate (SPA), polyethylenimine (PEI),...
-
OPTICS AND LASER TECHNOLOGY
Journals -
The study on minimum uncut chip thickness and cutting forces during laser-assisted turning of WC/NiCr clad layers
Publication -
Pressure field in a plane layer
PublicationPraca prezentuje wyniki badań teoretycznych i numerycznych zagadnienia przejścia fal płaskich przez warstwę. Omówiono zagadnienie tworzenia i rozchodzenia się fal w poszczególnych warstwach. Zaproponowano model matematyczny opisujący zmiany ciśnienia wewnątrz warstwy. Analizowano ciśnienie wewnątrz warstwy, fale bieżące i odbite wewnątrz warstwy oraz w ośrodku otaczającym. Przedstawiono wyniki badań numerycznych.
-
Scanning with Laser Beam over the TiO2 Nanotubes Covered with Thin Chromium Layers towards the Activation of the Material under the Visible Light
Publication -
Laser and Optoelectronics Progress
Journals -
Infrared and Laser Engineering
Journals -
JOURNAL OF LASER APPLICATIONS
Journals -
LASER AND PARTICLE BEAMS
Journals -
LASER FOCUS WORLD
Journals -
Laser & Photonics Reviews
Journals