Filters
total: 4269
-
Catalog
- Publications 3347 available results
- Journals 44 available results
- Conferences 4 available results
- People 78 available results
- Projects 6 available results
- Research Equipment 2 available results
- e-Learning Courses 84 available results
- Events 10 available results
- Open Research Data 694 available results
displaying 1000 best results Help
Search results for: sharing mobility
-
Feed forces during cutting of wood on frame sawing machines with narrow-kerf saws.
PublicationW pracy przedstawiono wybrane efekty energetyczne procesu przecinania drewna na pilarce ramowej za pomocą cienkich pił. Opisano wyniki badań eksperymentalnych sił posuwu przy zastosowaniu pił o dobrej jakości krawędzi skrawających (piły ostre) oraz pił których krawędzie skrawające były obarczone błędami wykonania w postaci wyszczerbień i wykruszeń krawędzi skrawających. Badania przeprowadzono na pilarce ramowej PRW15M.
-
Cutting forces related to the direction of primary motion during machining on frame sawing machines.
PublicationW pracy przedstawiono efekty energetyczne przecinania drewna na pilarce ramowej za pomocą cienkich pił. Podano podstawy teoretyczne oraz wyniki badań doświadczalnych sił skrawania działających na kierunku ruchu głównego ( siły skrawania określano podczas podawania przecinanego materiału oraz w czasie gdy prędkość posuwu wynosiła 0).
-
Optimal selection of the sawdust separation device for a narrow-kerf sawing machine PRW15-M
PublicationW pracy przedstawiono granulometryczną analizę rozkładu wiórów i pyłu drzewnego otrzymanego w procesie przecinania suchych pryzm sosnowych na pilarce ramowej wielopiłowej PRW15-M. Wielkości wiórów mieściły się w granicach od 84,7 μm do nawet 14 mm. Te ostatnie są elementami będącymi efektem rozszczepiania dolnej powierzchni pryzmy przez wychodzące z niej ostrza piły. Większośc wiórów z najmniejszych frakcji ma postać sześciennych...
-
Application in circular sawing machines of the experimental results of investigations of the chip removing system operation
PublicationThe experimental results of the chip removing system operation are presented. The main aim of them was to optimize suction system of the panel saw Fx3 and its follower Fx550. The attention was focused on the upper casing, which was the part of removing system. Within the framework of the work a systematic experimental study of pressure distribution in the casing during operation of the selected rotational speed of saw blade with...
-
The effect of current signal filtering method on the value of cutting power while sawing wood
PublicationThe goal of this work was to investigate an effect of various signal pre-processings on the outline of the electrical power curve and its influence on the measured cutting force estimation. Two signal processing methods were selected for the needs of the experiment, including digital filter and wavelet transform. The filter used was Butterworth, 3rd order band-stop with the cut-out band from 45 Hz to 55 Hz. The second approach...
-
Predictions of cutting power while sawing of birch and beech with the use of modern fracture mechanics
PublicationPraca zawiera wyniki badań eksperymentalnych procesu przecinania drewna brzozy i buka piłami o rzazie 2 mm na pilarce ramowej PRW15M. Na podstawie teoretycznego modelu Atkinsa, wyznaczono z danych eksperymentalnych stałe materiałowe (wiązkość i naprężenia tnące w strefie ścinania) i opracowano model do prognozowania mocy skrawania podczas przecinania drewna piłami na pilarce ramowej dla innych wartości rzazu w funkcji posuwu na...
-
Virtual spring damper method for nonholonomic robotic swarm self-organization and leader following
PublicationIn this paper, we demonstrate a method for self-organization and leader following of nonholonomic robotic swarm based on spring damper mesh. By self-organization of swarm robots we mean the emergence of order in a swarm as the result of interactions among the single robots. In other words the self-organization of swarm robots mimics some natural behavior of social animals like ants among others. The dynamics of two-wheel robot...
-
Alternative diagnostic method applied on marine diesel engines having limited monitoring susceptibility
PublicationThe paper presents a method of technical state evaluation of working spaces of a marine diesel engine at the limited control susceptibility. The method foresees making a diagnosis of the engine's working spaces on the basis of measurements of the exhaust gas pressure in the channels connecting engine cylinders with the turbocharger's turbine. Diagnostic measurements are carried out at representative (comparative) steady loads depending...
-
Alternative diagnostic method applied on marine diesel engines having limited monitoring susceptibility
PublicationThe paper presents a method of technical state evaluation of working spaces of a marine diesel engine at the limited control susceptibility. The method foresees making a diagnosis of the engine's working spaces on the basis of measurements of the exhaust gas pressure in the channels connecting engine cylinders with the turbocharger's turbine. Diagnostic measurements are carried out at representative (comparative) steady loads depending...
-
THE EFFECT OF LOG SORTING STRATEGY ON THE FORECASTED LUMBER VALUE AFTER SAWING PINE WOOD
PublicationThe optimal transformation path for the resource is determined by the quality of a log combined with its dimension. The commercial value of derived products is also closely connected with the size and extent of containing wood deficiencies. The results of studies with three diverse strategies for log sorting are presented in the paper. Resource assessment by a worker without extensive experience in sorting logs, the certified grading...
-
Effect of pine impregnation and feed speed on sound level and cutting power in wood sawing
PublicationThe sound levels along with the cutting power registered during the sawing process of the impregnated and non-impregnated pine wood at two feed speeds are shown and compared in this paper. Statistically significant differences in the acoustic signals occurred at the lower feed rate. The differences became smaller with an increase in the feed speed. In contrast to the sound signal, the differences...
-
Katarzyna Wojan dr hab.
PeopleDr habil., assiociate professor, Polish linguist, lexicographer, bibliographer; Finnish, Russian, Slavonic languages; confrontative linguistics, lexicology, lexicography, history of Polish lexicography, translation studies, intercultural communication, reception of Polish literature abroad, translations Editor-in-Chief of the Journal "Studia Rossica Gedanensia" (annual)
-
Andrzej Klimczuk
PeopleAndrzej Klimczuk, PhD, a sociologist and public policy expert, assistant professor in the Department of Social Policy of the Collegium of Socio-Economics at the SGH Warsaw School of Economics, Poland. Editor and correspondent of publications about computer and video games in the years 2002-2009. In 2011-2013, Vice President of the Foundation's Laboratory Research and Social Action "SocLab." External expert of institutions such...
-
Adam Wronkowski dr inż.
PeopleDoctor of social sciences in the discipline of socio-economic geography and spatial economy. Assistant Professor at the Faculty of Social and Economic Geography and Spatial Management at Adam Mickiewicz University in Poznań. He belongs to the Department of Spatial Economy and Urban Design. My research interests include geographies of children and young people, including, in particular, independent mobility, agency and the interrelationship...
-
The Influence of Cold Atmospheric Pressure Plasma-Treated Media on the Cell Viability, Motility, and Induction of Apoptosis in Human Non-Metastatic (MCF7) and Metastatic (MDA-MB-231) Breast Cancer Cell Lines
Publication -
Three-dimensional structure of wave-induced momentum flux in irrotational waves in combined shoaling-refraction conditions
Publication -
Synthesis and photochemical properties of unsymmetrical phthalocyanine bearing two 1-adamantylsulfanyl groups at adjacent peripheral positions
Publication -
Design of serine proteinase inhibitors by combinatorial chemistry using trypsin inhibitor SFTI‐1 as a starting structure
Publication -
A new methodological approach to the noise threat evaluation based on the selected physiological properties of the human hearing system
PublicationA new way of assessment of noise-induced harmful effects on human hearing system is presented in the paper. The method takes into consideration properties of the selected physiological human hearing system. On the basis of the hearing examinations and noise measurements results and psychoacoustical noise dosimeter performance the new indicators of the noise harmfulness were proposed. The evaluation of the proposed indicators were...
-
The application of magnetic fluids in sealing nodes designed for operation in difficult conditions and in machines used in sea environment
PublicationPresented in article MF seals are being researched for sea technology purposes due to their excellent tightness and low resistance of motion. These features are most valuable for ring propellers and ship's main propeller shaft. There are more reasons why technologists payf significant attention for various MFseals applications in their difficult operating conditions. For instance, an advanced pumping systems are designed with contactless...
-
BCR expression is decreased in meningiomas showing loss of heterozygosity of 22q within a new minimal deletion region
Publication -
Up-regulation of ferritin ubiquitination in skeletal muscle of transgenic rats bearing the G93A hmSOD1 gene mutation
Publication -
The application of magnetic fluids in sealing nodes designed for operation in difficult conditions and in machines used in sea environment
PublicationPresented in article MF seals are being researched for sea technology purposes due to their excellenttightness and low resistance of motion. These features are most valuable for ring propellers and ship'smain propeller shaft. There are more reasons why technologists payf significant attention for various MFseals applications in their difficult operating conditions. For instance, an advanced pumping systemsare designed with contactless...
-
Intra-operative gallbladder scoring predicts conversion of laparoscopic to open cholecystectomy: a WSES prospective collaborative study
Publication -
Identyfikacja krytycznych uszkodzeń ścianek rurociągów na podstawie analizy MDCR w oparciu skaning ultradźwiękowy.
PublicationW pracy przedstawiono system ultradźwiękowych tłoków pomiarowych wysokiej rozdzielczości dostarczający informacji o parametrach geometrycznych wykrytych ubytków metalu w ściankach badanego rurociągu. Informacje te pozwalają na oszacowanie MDCR uznanego za jeden z podstawowych wskaźników pozwalających na bezpieczną eksploatację rurociągów.
-
Numerical Determination of the Load-Bearing Capacity of a Perforated Thin-Walled Beam in a Structural System with a Steel Grating
PublicationThis article presents the results of numerical simulations of a structural system consisting of steel perforated thin-walled beams and a steel grating. The simulations were conducted using the finite element method. The analysis took into account physical and geometric nonlinearity as well as the contact between the steel grating and the beams. The main goal of the research was to develop load-bearing curves for the main beam in...
-
Rapid simulation-driven design of miniaturised dual-band microwave couplers by means of adaptive response scaling
PublicationOne of the major challenges in the design of compact microwave structures is the necessity of simultaneous handling of several objectives and the fact that expensive electromagnetic (EM) analysis is required for their reliable evaluation. Design of multi-band circuits where performance requirements are to be satisfied for several frequencies at the same time is even more difficult. In this work, a computationally efficient design...
-
Tilting pad thrust bearing with novel material selection - experimental comparison of low and medium speed operation
PublicationThe advances in material engineering led to the development of hard carbon based coatings applied in numerous applications in order to prevent or minimize wear of the parts in contact. With Triondur® coatings, the bearing company Schaeffler has succeeded in halving the friction losses in the valve trains of passenger cars. The coatings are optimized for high abrasive wear protection and low sliding friction moments. Altogether...
-
Derivation of the scaling laws used in geotechnical centrifuge modelling-application of dimensional analysis and Buckingham Π theorem
PublicationGeotechnical centrifuge modelling has been a world-wide used technology in physical tests. In this paper a derivation of scaling laws by dimensional analysis for the centrifugal modelling is presented. Basic principles of centrifuge modelling are described. Scaling laws for slow events like consolidation and fast events like dynamic loads are shown. The differences in scale factors for both processes are noticed. The aim of this...
-
Expert opinion on the effectiveness of protection against electric shock in case of fault in an installation for electric vehicles charging
PublicationThe opinion concerns the use of residual current devices for protection against electric shock by automatic disconnection of supply in a Norwegian installation intended for charging of electric vehicles.
-
ANALYSIS OF BEARING CLEARANCE AND WIDTH OF OIL GROOVE ON CHARACTERISTIC OF FLUID FILM IN HYDRODYNAMIC MAIN CRANKSHAFT BEARINGS
PublicationAbstract Paper represents analysis of influence of oil groove width and bearing clearance on characteristics of oil film in hydrodynamic journal main crankshaft bearing. Analysis was performed in purpose to define influence of bearing clearance and dimensions of oil groove on static characteristics and manufacturability of half shelf bearings in industrial high-volume production. Computer simulations was made using ARTbear program...
-
Bearing capacity of piles based on static load tests and calculation principles provided by EN 1997-1
PublicationW artykule scharakteryzowano i przeanalizowano ogólne zalecenia Eurokodu 7 dotyczące wyznaczania nośności pali na podstawie próbnych obciążeń statycznych. Porównano je z zaleceniami dotychczasowej polskiej normy PN-83/B-02482. Przedstawiono kilka przykładów interpretacji rzeczywistych wyników próbnych obciążeń pali według zaleceń wyżej wymienionych dwóch norm wraz z analizą porównawczą.
-
Synthesis and characterization of biopolyols through biomass liquefaction of wood shavings and their application in the preparation of polyurethane wood composites
PublicationThe sustainability of production systems in wood processing, wood industry, and wooden waste disposal is an important issue for European industry and society. Proper development of products based on renewable wood resources gives an opportunity to provide materials with long-term environmental, social, and economic sustainability. This study aims to establish a new way of forestry and agricultural waste materials utilization by...
-
Experimental Research on Insufficient Water Lubrication of Marine Stern Tube Journal Bearing with Elastic Polymer Bush
PublicationWater-lubricated bearings with polymer bushes are steadily gaining popularity due to their advantages, including environmental friendliness, relatively simple construction and long-term operation. Nevertheless, in practice instances of damage to such bearings occur due to insufficient or absent flow of the lubricating agent. In this study, experimental tests established that elastic polymer bush bearing is capable of operating...
-
The influence of polymer bearing material and lubricating grooves layout on wear of journal bearings lubricated with contaminated water
PublicationThe goal of the present paper is to investigate wear properties of journal sliding bearing operating in the conditions of contaminated water lubrication. Several bearing materials and bearing sleeve designs (differing in the axial grooves position and their shape) were tested experimentally under typical operating conditions in a dedicated test rig, which was equipped with a lubricating system, enabling lubrication with contaminated...
-
Proposal for calculating the bearing capacity of screw displacement piles in non-cohesive soils based on CPT results
PublicationPrzedstawienie wyników badań terenowych pali przemieszczeniowych wkręcanych, zrealizowanych w ramach projektu badawczego MNiSW. Propozycja dwóch metod obliczania nośności pali przemieszczeniowych wkręcanych w niespoistym podłożu gruntowym na podstawie wyników badań CPT. Metody dostosowano do wytycznych Eurokodu 7. Weryfikacja metod obliczeniowych z wynikami badań terenowych pali.
-
The ability of children aged 6 and 9 years, respectively, to detect errors in a narrative based on incorrect information about evaporation in the water cycle
Publication -
Ability of paramedics to perform endotracheal intubation during continuous chest compressions: a randomized cadaver study comparing Pentax AWS and Macintosh laryngoscopes
Publication -
Estimation of the Chelating Ability of an Extract from Aronia melanocarpa L. Berries and Its Main Polyphenolic Ingredients Towards Ions of Zinc and Copper
Publication -
Design and Optimization of Metamaterial-based Highly-isolated MIMO Antenna with High Gain and Beam Tilting Ability for 5G Millimeter Wave Applications
PublicationThis paper presents a wideband multiple-input multiple-output (MIMO) antenna with high gain and isolation, as well as beam tilting capability, for 5G millimeter wave (MMW) applications. A single bow-tie antenna fed by a substrate-integrated waveguide (SIW) is proposed to cover the 28 GHz band (26.5–29.5 GHz) with a maximum gain of 6.35 dB. To enhance the gain, H-shaped metamaterial (MM)-based components are incorporated into the...
-
The semi-Markov model of the process of appearance of sea-going ship propupsion system ability and inability states in application to determining the reliablity of these systems
PublicationThe article presents possible application of the theory of semi-Markov processes in creating the eight-state model of the process of appearance of the propulsion systems ability and inability states on sea-going vessels performing transportation tasks in a relatively long operating time t (t → ∞). The model has been proved to be able to be successfully used for determining the reliability of the abovementioned systems. The probability...
-
Daniel Chuchała dr hab. inż.
People -
Influence of SDHI Seed Treatment on the Physiological Conditions of Spring Barley Seedlings under Drought Stress
Publication -
Evaluating the challenges and needs of parents caring for children with Williams syndrome: A preliminary study from Poland
PublicationBackground: Although physical, cognitive and behavioural manifestations of Williams syndrome(WS) affect every dimension of caregivers lives, no studies on the parental experiences of caringfor a WS child have to date been carried out in Poland.Methods: In order to identify the challenges and needs of Polish carers of WS children a survey wasconducted...
-
Road mortality of pond-breeding amphibians during spring migrations in the Mazurian Lakeland, NE Poland
Publication -
Professional activity, gender and disease-related emotions: The impact on parents' experiences in caring for children with phenylketonuria
PublicationIntroduction: Clinical management of rare diseases often fails to acknowledge the challenges faced by caregivers.Whilst management of phenylketonuria (PKU) may not be considered as dire as other conditions, most studiesprimarily concentrate on clinical issues, dietary adherence, or the quality of life of the PKU patients, leavingcaregivers in the background. The aim of the study was to evaluate the psychosocial...
-
Professional activity, gender and disease-related emotions: The impact on parents' experiences in caring for children with phenylketonuria
Publication -
Washboarding during cutting on frame sawing machines II. Experimental study of the saw blade behaviour
PublicationPraca jest swego rodzaju suplementem do referatu przedstawianego na 15th Inernational Wood Machining Seminar w Los Angeles, CA, USA. Opisano uzyskane wyniki badań doświadczalnych prowadzonych w oparciu o plan badań Hartley`a.Czynnikami badanymi były: naprężenia napinające brzeszczotu piły, częstotliwość skoków ramy piłowej oraz wysokość cięcia przedmiotu obrabianego. Czynnikami wynikowymi były: wysokość sfalowania powierzchni oraz...
-
Analysis of surface roughness of chemically impregnated Scots pine processed using frame-sawing machine
PublicationThe objective of this work was to evaluate the effect of the impregnation process of pine wood (Pinus sylvestris L.) on roughness parameters of the surface processed on a frame sawing. The samples weredried and impregnated using a commercial procedure by a local company. The touch method withthe use of measuring stylus (pin) was employed to determine of surface roughness of the samplesconsidering parameters, namely, arithmetical...
-
CUTTING POWER FORECASTING WHILE WOOD SAWING: FRACTURE MECHANICS APPROACH AND AXELSSON’S MODEL COMPARISON
PublicationIn the classical approach, energetic effects (cutting forces and cutting power) of wood sawing process are generally calculated on the basis of the specific cutting resistance, which is in the case of wood cutting the function of more or less important factors. On the other hand, cutting forces (power) could be considered from a point of view of modern fracture mechanics. Another way is to forecast cutting power consumption on...