Wyszukiwarka
dr hab. inż. Paweł Dymarski
Publikacje
Filtry
wszystkich: 29
Katalog Publikacji
Rok 2023
-
MODELLING OF THE VISCOSITY EFFECT OF HEAVE PLATES FOR FLOATING WIND TURBINES BY HYDRODYNAMIC COEFFICIENTS
PublikacjaOne of the methods of modelling the movement of floating wind turbines is the use of the diffraction method. However, this method does not take into account the influence of viscosity; therefore, in many cases, it needs to be extended with a matrix of appropriate coefficients. The effect of viscosity causes both the added mass coefficient and the damping coefficient to increase. The determined coefficients were entered into the...
Rok 2022
-
An innovative method of measuring the extension of the piston rod in hydraulic cylinders, especially large ones used in the shipbuilding and offshore industry
PublikacjaThe article presents the results of selected works related to the wider subject of research conducted at the Faculty of Mechanical Engineering and Shipbuilding at the Gdańsk University of Technology, regarding designing various on board devices with hydraulic drive for ships and other offshore facilities. One of the commonly used these mechanisms are hydraulic actuators with the measurement of the piston rod extension. The issue...
-
Analysis of the Hydrodynamic Properties of the 3-Column Spar Platform for Offshore Wind Turbines
PublikacjaThe article presents a design of a floating platform for offshore wind turbines. The concept is a modification of the Spar design and consists of three variable section columns connected to each other by a ballast tank in the lower part of the platform. This solution makes it possible to influence the position of the centre of buoyancy and the centre of mass of the structure. Compared to the classic Spar platform structure, the...
-
Heave Plates with Holes for Floating Offshore Wind Turbines
PublikacjaThe paper presents an innovative solution which is heave plates with holes. The long-known heave plates are designed to damp the heave motion of platforms. They are most often used for Spar platforms. The growing interest in this type of platform as supporting structures for offshore wind turbines makes it necessary to look for new solutions. Based on the available literature and the authors’ own research, it was concluded that...
Rok 2019
-
Design of Jack-up Platform for 6 MW Wind Turbine: Parametric Analysis Based Dimensioning of Platform Legs
PublikacjaThe article presents the results of the research conducted within the framework of the project entitled WIND-TU-PLA (ERA-NET, MARTEC II), the general aim of which was to design and analyse supporting structures for wind turbines intended for operation on the South Baltic area. The research part described in the article aimed at developing a preliminary design for a jack-up platform which can operate on water areas with depth of...
-
Stability Analysis of the Floating Offshore Wind Turbine Support Structure of Cell Spar Type During its Installation
PublikacjaThe article presents the results of selected works related to the wider subject of the research conducted at the Faculty of Ocean Engineering and Ship Technology of the Gdansk University of Technology, which concerns design and technology of construction, towing, and settlement on the seabed, or anchoring, of supporting structures for offshore wind farms. As a result of this research, several designs of this type of objects were...
Rok 2018
-
Vertical motions damping model test of a lifeboat lowered onto a flat sea surface
PublikacjaThe article presents the experiment’s results of the lifeboat model lowered with an initial speed and then released to fall onto a flat water surface. The purpose of the research is to determine the trajectory of the vertical boat motion and describe it with a mathematical model. This is closely related to determining the damping factor since the vertical motion is damped and the lifeboat gets balanced and stops moving after some...
Rok 2017
-
Design of Structure of Tension Leg Platform for 6 MW Offshore Wind Turbine Based On Fem Analysis
PublikacjaThe article presents the calculation and design stages of the TLP platform serving as a supporting construction of a 6 MW offshore wind turbine. This platform is designed to anchor at sea at a depth of 60 m. The authors presented the method of parameterization and optimization of the hull geometry. For the two selected geometry variants, the load and motion calculations of the platform subjected to wind, wave and current under...
-
Searching for Critical Conditions During Lifeboat Launching – Simulations
PublikacjaThe article describes numerical simulations of the process of lifeboat launching at the ship’s side. The research is aimed at finding the values of ship motion parameters which appear to be most dangerous for people in the lowered lifeboat due to the generated accelerations. The simplified model of ship hull motion adopted at this research stage bases on a superposition of harmonic motions with given amplitudes and periods in six...
-
Technology Concept of TLP Platform Towing and Installation in Waters with Depth of 60 m
PublikacjaThe article is part of the design and research work conducted at the Gdansk University of Technology, Faculty of Ocean Engineering and Ship Technology, in cooperation with a number of other research centres, which concerns offshore wind farms planned to be built in the Polish zone of the Baltic sea in the next years. One of most difficult tasks in this project is building suitable foundations for each power unit consisting of a...
Rok 2016
-
Developing Methodology for Model Tests of Floating Platforms in Low -Depth Towing Tank
PublikacjaThe paper presents two different methods of physical modeling of semi-submersible platform mooring system for research in low depth towing tank. The tested model was made in the scale of 1:100 resembling the "Thunder Horse" platform moored in the Gulf of Mexico at a depth of 1,920 m. Its mooring system consisted of 16 semi-taut mooring lines (chain-wire-chain) spaced starshape and attached at the bottom to suction piles. The tests...
-
Effective method for determining environmental loads on supporting structures for offshore wind turbines
PublikacjaThis paper presents a description of an effective method for determining loads due to waves and current acting on the supporting structures of the offshore wind turbines. This method is dedicated to the structures consisting of the cylindrical or conical elements as well as (truncates) pyramids of polygon with a large number of sides (8 or more). The presented computational method is based on the Morison equation, which was originally...
Rok 2015
-
DESIGN AND STRENGTH CALCULATIONS OF THE TRIPOD SUPPORT STRUCTURE FOR OFFSHORE POWER PLANT
PublikacjaThe support structure being the object of the analysis presented in the article is Tripod. According to the adopted assumptions, it is a foundation gravitationally set in the water region of 60 m in depth, not fixed to the seabed, which can be used for installing a 7MW wind turbine. Due to the lack of substantial information on designing and strength calculations of such types of structures in the world literature, authors have...
Rok 2014
-
A numerical model to simulate the motion of a lifesaving module during its launching from the ship’s stern ramp
PublikacjaThe article presents a numerical model of object motion in six degrees of freedom (DoF) which is intended to be used to simulate 3D motion of a lifesaving module during its launching from a ship using a stern ramp in rough sea. The model, of relatively high complexity, takes into account both the motion of the ship on water in changing sea conditions, and the relative motion of the ramp with respect to the ship. The motion of the...
-
Computational simulation of motion of a rescue module during its launching from ship at rough sea
PublikacjaThis paper is a continuation of the work titled : “A comp utational model for simulation of motion of rescue module during its launching from stern ramp of a ship at rough sea”. It presents results of computer simulations of motion of a rescue module with embarked persons during its launching on rollers along stern ramp of a ship at rough sea. The simulations were conducted for a selected ship fitted with a launching ramp , for...
-
Developing a methodology for model tests of floating platforms in a towing tank of low depth
PublikacjaThe paper presents two ways to mooring model of semi-submersible platform for research in the small depth towing pool. The tested model was made in the likeness of 1:100 Thunder Horse platform moored in the Gulf of Mexico at a depth of 1,920 m. Its mooring system consisted of 16 semi-taut mooring lines (chain-wire-chain) spaced Star-shape and attached at the bottom to the suction piles. The tests were performed in the towing pool...
-
Effective method for determining environmental loads on supporting structures for offshore wind turbines
PublikacjaThis paper presents a description of an effective method for determining loads due to waves, current and wind acting on the supporting structures of the offshore wind turbines. This method is dedicated to the structures consisting of the cylindrical or conical elements as well as (truncates) pyramids of polygon with a large number of sides (8 or more). The presented computational method is based on the Morison equation, which was...
-
Verification of algorithms determining wave loads on support structure of wind turbine
PublikacjaThe offshore wind turbines require determination of wave loads on their support structure. This structure is fixed and, therefore, this problem is reduced to solving only the diffraction problem, which is determined by Laplace equation and conditions on the following boundaries: on the support structure, on the sea free surface and on its bottom, and at infinity on free surface. The linear problem was applied to determine the wave...
Rok 2013
-
Numerical Analysis of Impact of Energy Buoy Anchoring Configurations on its Motion and Efficiency
PublikacjaThis paper presents a numerical analysis of the impact of energy buoy mooring configurations on its movement on the wave and effectiveness. The method used to analyse the buoy movement modelling in six degrees of freedom was described in a paper presented at the Conference 2011. Simulations of the buoy movement in regular wave and power calculations were conducted for several configurations of anchoring systems and position of...
Rok 2012
-
Computational model for simulation of lifeboat motions during its launching from ship in rough seas
PublikacjaW artykule przedstawiono model obliczeniowy 3 D, opisujący ruch obiektu w 6 stopniach swobody (6DoF), do symulacji ruchu jedno- lub dwuzawiesiowej łodzi ratunkowej lub ratowniczej podczas opuszczania ze statku na wzburzonej wodzie. Jest to złożony model uwzględniający warunki morskie oraz elastyczność i własności tłumiące elementów i mechanizmów żurawika, liny oraz kadłuba łodzi. Ponadto przedstawiono przykładowe wyniki obliczeń...
-
Design solution and selected research results of the sea-wave energy converter
PublikacjaW artykule przedstawiono oryginalne rozwiązanie konstrukcyjne boi do pozyskiwania energii fal morskich oraz analizy i badania modelowe turbiny wodnej poprzedzające wybór ostateczny konstrukcji modelu boi w skali 1:5 przewidzianego do badań eksperymentalnych w basenie holowniczym. Zaprezentowano także wybrane wyniki badań modelowych i symulacji komputerowych ukazujący wpływ systemu kotwiczenia i innych parametrów na jakość i efektywność...
-
Model research and numerical calculations of the buoy for capturing of the sea-waves energy
Publikacjaw pracy przedstawiono konstrukcję i zasadę działania modelu 1:5 boi do pozyskiwania energii fal morskich oraz wyniki badań eksperymentalnych prowadzonych w dużym basenie w Centrum techniki Okrętowej w Gdańsku.Ponadto przedstawiono numeryczny model obliczeniowy i wybrane wyniki symulacji zachowania się boi na fali regularnej.
-
Numerical modelling of moored floating structures using SPH. Preliminary results
PublikacjaThis article presents partial results of the works carried out under the research project "The development of the methodof modeling the dynamics of the floating (offshore) objects subjected to the environment influence", which aims at developing computational methods for modeling the dynamics of offshore structures.The article contains the description of the method of modeling the hydrodynamic impacts using SPH method and the description...
Rok 2011
-
Numerical simulation of energy buoy motion in wave
PublikacjaW pracy przedstawiono opis numerycznej metody modelowania ruchu boi energetycznej na fali. Wyniki obliczeń porównano z wynikami otrzymanymi z badań modelowych przeprowadzonych w basenie hydromechanicznym.
Rok 2010
-
A method for the accurate numerical prediction of the tip vortices shed from hydrofoils
PublikacjaPraca przedstawia wyniki obliczeń numerycznych rozkładu wirowości i pól prędkości w przekrojach wirów wierzchołkowych generowanych przez płaty nośne. Obliczenia przeprowadzono przy pomocy nowej, wyspecjalizowanej metody dyskretyzacji obszaru przepływu. Rezultaty obliczeń porównano z wynikami pomiarów anemometrem laserowym za modelami płatów w tunelu kawitacyjnym. Porównanie to potwierdziło skuteczność nowej metody dyskretyzacji...
Rok 2009
-
An Experimental and Numerical Study of the Vortces Generated by Hydrofoils
PublikacjaArtykuł przedstawia wyniki projektu badawczego poświęconego wirom generowanym przez płaty nośne. W części eksperymentalnej wykonano anemometrem laserowym pomiary pól prędkości w poprzecznych przekrojach wirów. W częsci numerycznej przeprowadzono obliczenia używając różnych struktur siatki obliczeniowej i różnych modeli turbulencji. Na podstawie porównania wybrano model turbulencji i strukturę siatki najlepiej odzwieciedlające pole...
-
numerical prediction of vortex generated by hydrofoil
PublikacjaW pracy przedstawiono wyniki obliczeń programami Fluent i Comet dla płata śruby napędowej. Pola prędkości oraz wirowość za płatem porównano z wynikami pomiarów (LDA- Laser Doppler Anemometry) w tunelu kawitacyjnym Centrum Techik Okrętowych (CTO). Przedstawiono wpływ adaptacji siatki wg różnych kryteriów (lokalnej wirowości lub prędkości) na zgodność wyników obliczeń z danymi eksperymentalnymi.
Rok 2006
-
Ramp and chain-lift-launched lifeboats - radical concepts for evacuating cruise ships
PublikacjaW artykule przedstawiono dwie oryginalne koncepcje systemów ewakuacyjnych statków pasażerskich. Pierwsza z nich polega na zastosowaniu otwieranej rampy i pochylni z rolkami, na których umieszczone są w rzędzie łodzie ratunkowe, zaczepione do elementów wyciągu łańcuchowego. Druga koncepcja polega na umieszczeniu łodzi, jedna nad drugą, na wyciągu łańcuchowym. W obu systemach w trakcie ewakuacji łodzie opuszczane są grawitacyjnie...
-
Urządzenia ratunkowe i ratownicze statków - prace projektowo badawcze
PublikacjaW referacie przedstawiono dotychczasowe prace projektowo-badawcze, dotyczące okrętowych urządzeń ratunkowych i ratowniczych, prowadzone na Wydziale Oceanotechniki i Okrętownictwa PG oraz aktualnie realizowany zakres prac prowadzonych w ramach 6 Europejskiego Programu Ramowego pod nazwą ''Safecrafts - bezpieczna ewakuacja ludzi ze statków''.
wyświetlono 3210 razy