Filtry
wszystkich: 869
wybranych: 787
Wyniki wyszukiwania dla: gas turbine · combustion chamber · steam injection · marine power plant
-
Gas turbine: advanced marine propulsion.
PublikacjaPrzedstawiono rys historyczny rozwoju okrętowych turbin gazowych. Omówiono główne problemy zastosowania turbiny gazowej jako głównego silnika okrętowego i współczesne tendencje rozwoju tego napędu.
-
On the Use of Selected 4th Generation Nuclear Reactors in Marine Power Plants
PublikacjaThis article provides a review of the possibility of using different types of reactors to power ships. The analyses were carried out for three different large vessels: a container ship, a liquid gas carrier and a bulk carrier. A novelty of this work is the analysis of the proposal to adapt marine power plants to ecological requirements in shipping by replacing the conventional propulsion system based on internal combustion engines...
-
Influence of Different Biofuels on the Efficiency of Gas Turbine Cycles for Prosumer and Distributed Energy Power Plants
PublikacjaThe efficiency of a gas turbine can be affected by the use of different biofuels usually with a relatively Lower Heating Value (LHV). The paper evaluates the impact of calorific value of fuel on turbine performance and analyzes the possibilities of optimizing turbine construction from the point of view of maximum efficiency for a particular fuel. The several variants of design of small power microturbines dedicated to various biofuels...
-
INFLUENCE OF INLET GEOMETRY ON THE EFFICIENCY OF 1MW STEAM TURBINE
PublikacjaThe process of the design of the 1MW steam turbine includes designing the stator and rotor blades, the steam turbine inlet and exit, the casing and the rotor. A turbine that operates at rotation speeds other than 3000 rpm requires a gear box and generator with complex electronic software. This paper analyses the efficiency of eight turbine variants, including seven inlet geometries and three stages of stator as well as an eight...
-
Analysis of the structure of the atomized fuel spray with marine diesel engine injector in the early stage of injection
PublikacjaThis paper presents the results of the experimental research of the atomized fuel spray with the marine diesel engine injector in the constant volume chamber. The specificity of the phenomena occurring in the marine engine cylinder was the reason to use the optical visualisation method in the studies – the Mie scattering technique. This work presents an analysis of the influence of different geometry of outlet orifice and opening...
-
ISSUES OF ECONOMIC ANALYSIS OF ELECTRIC ENERGY GENERATION IN A FLOATING POWER PLANT
PublikacjaThis article presents basic dependences for conducting a technical and economic analysis related with investment projects. It describes a combined system of a compression ignition engine and a steam turbine, whose aim, when placed on a floating platform, is to generate electric energy in the so-called distributed generation system. Such a system involves a reciprocating internal combustion engine and a connected steam turbine system...
-
Experimental ORC micro-power plant for CHP application Part A: power plant arrangement
PublikacjaThe co-generative micro-power plant with the HFE7100 applied as a working medium was designed and built for experimental investigations. The heat output of the plant was assumed equal to 20 kW, while the electric output amounted to about 3kW. Examples of the results of the preliminary experimental research on a boiler, heat exchangers, a pump and a turbine-generator set are presented and analysed.
-
Preliminary design of the last stage of supercritical steam turbine and proposition of anti-erosion coating for blades surface
PublikacjaIn this article a preliminary design of the last stage of supercritical steam turbine has been presented. A computational model of supercritical thermal cycle has been created in order to determine steam parameters at the stage inlet and outlet. The model was based on the structure of German coal-fired power plant Datteln 4. Further steam-flow parame-ters and dimensions of stator and rotor blades have been calculated analytically....
-
Multi-region fuzzy logic controller with local PID controllers for U-tube steam generator in nuclear power plant
PublikacjaIn the paper, analysis of multi-region fuzzy logic controller with local PID controllers for steam generator of pressurized water reactor (PWR) working in wide range of thermal power changes is presented. The U-tube steam generator has a nonlinear dynamics depending on thermal power transferred from coolant of the primary loop of the PWR plant. Control of water level in the steam generator conducted by a traditional PID controller...
-
Advanced Control Structures of Turbo Generator System of Nuclear Power Plant
PublikacjaIn the paper a synthesis of advanced control structures of turbine and synchronous generator for nuclear power plant working under changing operating conditions (supplied power level) is presented. It is based on the nonlinear models of the steam turbine and synchronous generator cooperating with the power system. Considered control structure consists of multi-regional fuzzy control systems with local linear controllers, including...
-
Advanced Control Structures of Turbo Generator System of Nuclear Power Plant
PublikacjaIn the paper a synthesis of advanced control structures of turbine and synchronous generator for nuclear power plant working under changing operating conditions (supplied power level) is presented. It is based on the nonlinear models of the steam turbine and synchronous generator cooperating with the power system. Considered control structure consists of multi-regional fuzzy control systems with local linear controllers, including...
-
EXHAUST GAS TEMPERATURE MEASUREMENTS IN DIAGNOSTICS OF TURBOCHARGED MARINE INTERNAL COMBUSTION ENGINES PART II DYNAMIC MEASUREMENTS
PublikacjaThe second part of the article describes the technology of marine engine diagnostics making use of dynamic measurements of the exhaust gas temperature. Little-known achievements of Prof. S. Rutkowski of the Naval College in Gdynia (now: Polish Naval Academy) in this area are presented. A novel approach is proposed which consists in the use of the measured exhaust gas temperature dynamics for qualitative and quantitative assessment...
-
A comparative study of pentanol (C5 alcohol) and kerosene blends in terms of gas turbine engine performance and exhaust gas emission
PublikacjaThe growing demand for sustainable and clean energy sources provides the incentive for the development of alternative fuels. Simultaneously, the development of gas turbine technologies with flexible fuel supply systems enables the use of alternative non-fossil fuels that can play key roles in contributing to global efforts in meeting emissions targets. This paper presents the current state of knowledge on the production and potential...
-
Determination of Failure Causes of a Steam Turbine Casing
PublikacjaThe paper presents results of research and failure analysis undertaken to determine failure causes of a steam turbine casing. After 130,000 hours of service the crack in a outer shell of the turbine casing was found. The inner shell of the casing was made of cast steel grade G21CrMoV5-7, and the outer shell of grade G20CrMo4-5. Following research were performed in order to determine causes of the casing failure: chemical analysis;...
-
Different design aspects of an Organic Rankine Cycle turbine for electricity production using a geothermal binary power plant
PublikacjaIn recent years, pressure has been growing to increase the share of renewable energy sources in electricity generation, which may offer opportunities for the development of geothermal energy in regions that have been so far considered unprofitable in this respect. One such country currently undergoing an energy transition is Poland in which low-temperature geothermal resources are currently used for district heating and recreation...
-
Increase of power and efficiency of the 900 MW supercritical power plant through incorporation of the ORC
PublikacjaThe objective of the paper is to analyse thermodynamical and operational parameters of the supercritical power plant with reference conditions as well as following the introduction of the hybrid system incorporating ORC. In ORC the upper heat source is a stream of hot water from the system of heat recovery having temperature of 90 °C, which is additionally aided by heat from the bleeds of the steam turbine. Thermodynamical analysis...
-
An energetic analysis of a gas turbine with regenerative heating using turbine extraction at intermediate pressure - Brayton cycle advanced according to Szewalski's idea
PublikacjaIn this paper, a modification of a simple gas turbine into the Brayton cycle with regenerative heating, using turbine extraction at intermediate pressure, is presented. The main concept of the retrofitting is based on the transfer of heat from the turbine exhaust gases to the air entering the combustion chamber. The extracted gas transfers heat to air via the divided regenerative heat exchanger and after that is compressed and...
-
INFLUENCE OF DREDGER POWER PLANT TYPE AND DREDGER SIZE ON OUTPUT OF POWER PLANT INSTALLED ON TRAILING SUCTION HOPPER DREDGER
PublikacjaThis paper presents results of investigations dealing with influence of parameters characterizing size of suction hopper dredger as well as type of power system on magnitude of total output of combustion engines installed in dredger power plant.
-
Analysis of the possibility of increasing thermal-electric energy conversion ratio in CHP units based on micro gas turbine
PublikacjaThe aim of this paper is to analyze the possibility of increasing thermal energy to electricity conversion efficiency in combined heat and power (CHP) units based on micro gas turbine during low heat demand periods. At the beginning sustainable development postulates under power engineering are explained. Next micro CHP as part of distributed generation idea is presented. The main part of the article is based on results of thermodynamic...
-
Operation of the 900 MW power plant with the ORC supplied from three heat sources
PublikacjaThe chapter is aimed at utilisation of waste heat in the reference supercritical power plant in the manner to produce electricity in ORC installation. The waste heat is available in the form of a stream of hot water at 90°C, recovered from the exhaust gases in the amount of 200MW. Such low enthalpy heat source is rather insufficient to produce a good quality vapour to feed the ORC turbine. Therefore an original approach to increase...
-
THE THEORETICAL STUDY ON INFLUENCE OF FUEL INJECTION PRESSURE ON COMBUSTION PARAMETERS OF THE MARINE 4-STROKE ENGINE
Publikacja -
Isothermal turbines − New challenges. Numerical and experimental investigations into isothermal expansion in turbine power plants
PublikacjaThe efficiency of power plants with steam or gas turbines depends on the efficiencies of a thermodynamic cycle and devices implementing this cycle. In the case of high power outputs, we cannot expect a significant increase in the efficiency of individual devices. Therefore, what remains is to increase the efficiency of the implemented thermodynamic cycle - the complex Rankine cycle in the case of steam turbines or the extended...
-
Start-up of a power unit of a thermal power plant auxiliary systems with supply from a hydropower plant
PublikacjaThis article discusses the issues related to a power unit of a thermal power plant start-up with the use of a hydropower plant. Hydropower plant can supply and will enable start-up of auxiliary equipment in a power unit of a thermal power plant. Due to high capacity of auxiliary drives, start-up of auxiliaries in a thermal power plant after blackout (and boiler shutdown) is not possible from emergency energy sources in the power...
-
On Accuracy Modeling of Gas Turbine Cycles by the In-house COM-GAS Code
PublikacjaIn this paper, a comparison of accuracy modeling of gas turbine cycles between the basic (classical) model and the in-house COM-GAS code has been presented. The basic model uses a semi-perfect gas and well known projecting assumption. On the other hand, the computational flow mechanics (CFM) basis on a real gas by using thermodynamic tables. The thermodynamic analysis of thermal cycles, simply gas cycle GT8C and gas turbine cycle...
-
Optimisation of turbine shaft heating process under steam turbine run-up conditions
PublikacjaAn important operational task for thermal turbines during run-up and run-down is to keep the stresses in the structural elements at a right level. This applies not only to their instantaneous values, but also to the impact of them on the engine lifetime. The turbine shaft is a particularly important element. The distribution of stresses depends on geometric characteristics of the shaft and its specific locations. This means a groove manufactured...
-
Possibilities of the performance improvement of the aero- and marine propulsion units equipped with combustion piston engines
PublikacjaWithin the paper there have been presented the authors' opinions concerning possibilities and needs of the performance optimization of the aero- and marine units powered by piston engines both of ''classic'' and contemporary construction. There have been also discussed the reserves contained within combustion piston engines which enable its performance improvement (the power and specific fuel consumption) as well as the fulfillment...
-
Kinetic analysis of the stage for a high speed steam turbine
PublikacjaThis article analyzes possibilites of resonances within a control stage for a high speed steam turbine. This stage hase been based on assembling of a single blade to a rotating disk and increasing of rigidity of the system by using of a bandage. In the analysis will be nd a possiblity of resonance frequency, and mistuning by showing safety working ranges. The calculations have bean used the3D modal and harmonic analysis by the...
-
Diagnosing marine turbine engines through energy characteristics of their flow section
PublikacjaThe aim of the performed research was to develop of diagnostic method of the flow section of a marine turbine combustion engine based on the level of delamination of its energy characteristics. The here adopted diagnostic model provides for a formulation of the evaluation of the technical conditions based on the measurements of the parameters of the thermodynamic medium in the characteristic control cross-sections of the engine...
-
Thermal failure of a second rotor stage in heavy duty gas turbine
PublikacjaThe impulse mode of operation and the supply of various types of fuels causes frequent failures even in the heavy duty gas turbines. The paper presents the ravages of second rotor stage failure in a gas turbine. The excessive thermal elongation rise caused by fuel change was indicated as the main cause. We applied nonlinear numerical analysis, preceded by thermodynamic calculations of the turbine and visual inspection of the effects...
-
Methodology for implementing power plant efficiency standards for power generation: potential emission reduction
PublikacjaSome methods of generating power such as power generation through coal, natural gas, oil result in inevitable emissions of greenhouse gases. While power generation is necessary due to its increasing demand, it is important for power companies to generate their power in an efcient manner to reduce its efect on the environment. One of the most efective ways of tackling inefciency issues is through the implementation of efciency standard....
-
Specificity of automatic control of micro-turbines (steam or gas -driven and expanders) in dispersed generation system of heat and electric power
PublikacjaThis paper presents specific problems of automatic control of steam micro-turbines and expanders intended for the dispersed, combined generating of heat and electric power. The investigations concern ensurance of certainty of energy supply and its required quality.
-
The Matter of Decision-Making Control Over Operation Processes of Marine Power Plant Systems with the Use of their Models in the form of Semi-Markov Decision-Making Processes
PublikacjaThe article presents the possibility to control the real operation process of an arbitrary device installed in the marine power plant based on the four-state semi-Markov process, being the model of the process, which describes the transition process of operational states of the device and the transition process of its technical states. All these states are precisely defined for the ship main engine (SG). A hypothesis is proposed...
-
Synergistic effects of a swirl generator and MXene/ water nanofluids used in a heat exchanger pipe of a negative CO2 emission gas power plant
Publikacjafocus on optimizing heat exchangers contributes to improved temperature control mechanisms, ensuring the sustainable operation of innovative power plants working towards negative CO2 emissions. In the realm of oxy-combustion within Negative CO2 Emission Power Plants (nCO2PP), the temperature of combustion products surpasses 3000 (K). Addressing this challenge, the imperative arises to reduce these elevated temperatures to a manageable...
-
OPERATION OF TWO-SHAFT GAS TURBINE IN THE RANGE OF OPEN ANTI-SURGE VALVE
PublikacjaThis paper presents experimental tests of full-scale two-shaft gas turbine in the range of open anti-surge valve (ASV). The tests were carried out in a laboratory gas- turbine test stand belonging to Department of Automation and Power Engineering , Faculty of Ocean Engineering and Ship Technology , Gdańsk University of Technology. The tests covered the start-up and low load operation of the turbine set in the range of open...
-
Steam turbines governors in power system restoration process
PublikacjaThe paper discusses problems related to electric power system restoration process. The turbine controller operating mode influence in small subsystem is analyzed. There are considered abilities, advantages and drawbacks of the controller's two operating modes: power control and speed (frequen-cy) control, to rebuild electric power system from a single generating unit to a few parallel running generators.
-
The sources of contamination and reasons of damage of the flow part of the marine turbine engine in operation
PublikacjaThe aim of this paperis to show particular sensitivity of the flow part of the marine turbine engine to the presence of contaminations in the intake air. The contaminations form hard-to-remove deposits in the intervene channels that result in a reduced efficiency and performance of the engine. The paper classifies the contaminants according the source of their formation and their destructive force. The performed analyses and syntheses...
-
Technical and economic conditions of supplying residential consumers with heat from nuclear power plant
PublikacjaThe reduction of CO2 emission requires technological shift towards carbon-free options. Cogeneration of electricity and heat based on coal and natural gas will experience generation cost increase, if the costs of emissions are imposed on the plant operators. Therefore, nuclear and renewable options should be considered. In this paper, we present the concept of electricity and heat supply system with nuclear condensing turbine adapted...
-
Rozpoznawanie uszkodzeń w części przepływowej okrętowego turbinowego silnika spalinowego na podstawie wyników badania endoskopowego = Failures' recognising within the passages of a marine gas turbine engine on the basis of results of endoscopic investigation
PublikacjaThe paper deals with diagnostic issues concerning endoscopic examinations of marine gas turbine engines. There will be presented selected information about failures within the passages and accessible endoscopic methods and means enabling their detection. The author focuses on the endoscopic techniques and widely presents the possibilities of this quickly developed diagnostic method. There will be also presented representative results...
-
An Impact of Environmental Disturbances on Combined Cycle Power Plant Control
PublikacjaCombined cycle power plants operate at thermal efficiency approaching 60 percent. In the same time their performance presents several problems that have to be addressed. E.g. gas turbines are very sensitive to backpressure exerted on them by the heat recovery steam generators as well as to ambient pressure and temperature.
-
The system combined of low-speed marine diesel engine and steam turbine in ship propulsion applications
PublikacjaPrzedstawiono koncepcje okrętowego układu kombinowanego silnik wolnoobrotowy tłokowy- turbina parowa, wykorzystującego ciepło zawarte w spalinach wylotowych.Porównano układ kombinowany dużej mocy dla dwóch silników tłokowych porównywalnych mocy z punktu widzenia termodynamicznego.
-
Profitability criteria of partial cogeneration in nuclear power plant.
PublikacjaIn this paper, profitability criteria and calculation methodology of profitability conditions for partial cogeneration in nuclear power plant (NPP) was presented. Considered NPP supplies electricity to consumers through public power system, whereas heat is expected to be supplied to consumption regions via long-distance heat transport line. First proposed profitability criterion was total annual costs of electricity and heat delivered...
-
Analysis of possible application of high-temperature nuclear reactors to contemporary large-output steam power plants on ships
PublikacjaThis paper is aimed at analysis of possible application of helium to cooling high-temperature nuclear reactor to be used for generating steam in contemporary ship steam-turbine power plants of a large output with taking into account in particular variable operational parameters. In the first part of the paper types of contemporary ship power plants are presented. Features of today applied PWR reactors and proposed HTR reactors...
-
The Emission and Combustion Characteristics of Marine Diesel Engine with Extreme Throttled of Air or Exhaust Ducts
PublikacjaPresented paper shows the results of the laboratory tests on the relationship between the extreme throttling of both air intake duct and exhaust gas duct and gaseous emission from the marine engine. The object of research is a laboratory, 4-stroke, DI diesel engine, operated at loads from 50 kW to 250 kW at a constant speed equal to 750 rpm. During the laboratory tests the thermodynamic and exhaust gas emission characteristics...
-
Hydro Power Plant in the Process of Voltage Control in the Electric Power System and the System Restoration
PublikacjaThe article covers selected issues related to the share of hydroelectric power in the process of rebuilding the power system after black-out and voltage control during that process. Selected results of measurements made during the creation of the transmission chain for the need to start a block of a thermal power plant from a hydroelectric power plant were presented.
-
Technical and economical analysis of combined cycles of gas turbine -steam turbine on pipeline compressor stations. Part II - Economic analysis
PublikacjaW pracy przedstawiono zagadnienie nadbudowy zespołów turbosprężarkowych, znajdujących się na tłoczni gazu ziemnego, odzyskowymi blokami parowymi. W analizie tego przedsięwzięcia wzięto pod uwagę kilka wariantów konfiguracji układu parowego oraz kilka wariantów uwzględniających zmienność obciążenia turbin gazowych napędzających kompresory. Dla układu parowego dobrano wszystkie podstawowe parametry, a następnie wykonano obliczenia...
-
Technical and economical analysis of combined cycles of gas turbine - steam turbine on pipeline compressor stations. Part I - Technical analysis
PublikacjaW pracy przedstawiono zagadnienie nadbudowy zespołów turbosprężarkowych, znajdujących się na tłoczni gazu ziemnego, odzyskowymi blokami parowymi. W analizie tego przedsięwzięcia wzięto pod uwagę kilka wariantów konfiguracji układu parowego oraz kilka wariantów uwzględniających zmienność obciążenia turbin gazowych napędzających kompresory. Dla układu parowego dobrano wszystkie podstawowe parametry, a następnie wykonano obliczenia...
-
Technical and economical analysis of combined cycles of gas turbine - steam turbine on pipeline compressor stations. Part II - Economic analysis
PublikacjaW pracy przedstawiono zagadnienie nadbudowy zespołów turbosprężarkowych, znajdujących się na tłoczni gazu ziemnego, odzyskowymi blokami parowymi. W analizie tego przedsięwzięcia wzięto pod uwagę kilka wariantów konfiguracji układu parowego oraz kilka wariantów uwzględniających zmienność obciążenia turbin gazowych napędzających kompresory. Dla układu parowego dobrano wszystkie podstawowe parametry, a następnie wykonano obliczenia...
-
Analysis of diagnostic informativeness of the exhaust temperature of a naval gas turbine
PublikacjaThe conducted investigations aimed to carry out an analysis of the possibility that the failures identification in the automatic control system of a gas turbine engine could be worked out on the basis of measurements of the exhaust stream temperature behind the gas generator. The exhaust temperature represents a basic control parameter, enabling technical state evaluation of the engine within the operation process, which is observed...
-
The Application of Fluidic Sealing in Shrouded Gas Turbine Blades
PublikacjaThis paper presents a study conducted on a new gas turbine designed to limit leakage in the labyrinth seal. The slots in the fin are used to generate a bypass flow, which obstructs the flow in the gap above the fin. The method was tested numerically and experimentally beforehand using a simplified model without rotation or blade passages. In this paper, the validation of the method using a model of a turbine stage is shown. Reynolds-averaged...
-
CO2 capture using steam ejector condenser under electro hydrodynamic actuator with non-condensable gas and cyclone separator: A numerical study
PublikacjaThe concept for condensation of steam and CO2 separation in a negative CO2 emission gas power plant involves the utilization of a steam ejector condenser (SEC) for direct-contact condensation of vapor with inert gas (CO2) on a spray of subcooled liquid, integrated with a separator to produce pure CO2. Due to the increasing diffusion resistance and reduced convective heat transfer between the steam and subcooled water phases...