Filtry
wszystkich: 1199
wybranych: 1045
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: COLD-FORMED PROFILES, BUCKLING LOAD, LIMIT LOAD.
-
Influence of energy absorbers on Malgaigne fracture mechanism in lumbar-pelvic system under vertical impact load
Publikacja -
Speed Sensorless AC Drive with Inverter LC Filter and Fault Detection Using Load Torque Signal
PublikacjaThe industrial development in recent years has seen a major increase in the use of induction motors, whereby the cost has to be as low as possible and the lifetime as long as possible. To follow up this desire, investigations in this area have become very intense. For that reason, this paper presents a solution for driving an induction motor and simultaneous fault detection with no need for additional sensors. In order to achieve...
-
Analysis of load carrying capacity and destruction mechanism of an intermediate anchorage steel plate for pillar jib crane
PublikacjaPillar jib cranes are often mounted to existing floors with the use of an intermediate anchorage steel plate instead of using independent foundations, what is shown in the figure. Standards for steel design provide only basic rules for the design of such an intermediate plate. This study presents a simple design approach by using a numerical model in order to analyze different parameters that have significant influence in the anchorage...
-
Arterial stiffness increases in response to an acute arterial load challenge induced by an isometric handgrip in healthy individuals
Publikacja -
Bearing capacity of piles based on static load tests and calculation principles provided by EN 1997-1
PublikacjaW artykule scharakteryzowano i przeanalizowano ogólne zalecenia Eurokodu 7 dotyczące wyznaczania nośności pali na podstawie próbnych obciążeń statycznych. Porównano je z zaleceniami dotychczasowej polskiej normy PN-83/B-02482. Przedstawiono kilka przykładów interpretacji rzeczywistych wyników próbnych obciążeń pali według zaleceń wyżej wymienionych dwóch norm wraz z analizą porównawczą.
-
Investigation of natural frequencies of axially loaded thin-walled columns
PublikacjaThe paper deals with correlation between natural frequencies of two steel thin-walled columns and the corresponding applied load. The structures are made of cold-formed lipped channel sections. The columns lengths were assumed to follow two buckling patterns – global flexural and flexural-torsional buckling. In the thicker structure two material models were considered – linearly-elastic and elastic-perfectly plastic. Numerical...
-
Impact damage detection in smart composites using nonlinear acoustics—cointegration analysis for removal of undesired load effect
Publikacja -
Best State Estimate for the Phase Angles of Busbars in Power Systems via Circuit Modeled with DC Load Flow
Publikacja -
GB-SAR in the Diagnosis of Critical City Infrastructure—A Case Study of a Load Test on the Long Tram Extradosed Bridge
Publikacja -
Acute Effects of High-Load vs. Plyometric Conditioning Activity on Jumping Performance and the Muscle-Tendon Mechanical Properties
Publikacja -
Enhancement of Countermovement Jump Performance Using a Heavy Load with Velocity-Loss Repetition Control in Female Volleyball Players
Publikacja -
Comparison the heat load as the results of tests on human subject in a hot environment with the results obtained from numerical simulation
Publikacja -
The Development of a Combined Method to Quickly Assess Ship Speed and Fuel Consumption at Different Powertrain Load and Sea Conditions
PublikacjaDecision support systems (DSS) recently have been increasingly in use during ships operation. They require realistic input data regarding different aspects of navigation. To address the optimal weather routing of a ship, which is one of the most promising field of DSS application, it is necessary to accurately predict an actually attainable speed of a ship and corresponding fuel consumption at given loading conditions and predicted...
-
Load-carrying capacity and state of effort of tubes made of glass and basalt fibre reinforced polymer filled with concrete
PublikacjaOpisano badania eksperymentalne słupów wykonanych z rur polimerowych zbrojonych włóknami szklanymi i bazaltowymi. Część rur wypełniano wewnątrz betonem. Słupy z wypełnieniem niszczyły się w sposób powolny, wykazując wysoką nośność pokrytyczną, podczas gdy słupy z rur pustych niszczyły się w sposób gwałtowny, niesygnalizowany. Nośności uzyskane eksperymentalnie porównano do nośności obliczonych teoretycznie na podstawie procedur...
-
Fractographic-fractal dimension correlation with crack initiation and fatigue life for notched aluminium alloys under bending load
PublikacjaIn this study, fatigue fracture surfaces of aluminium alloy 2017-T4 notched specimens were investigated under cyclic bending to find an alternative failure loading index.. The surface topographies were measured on the entire fracture area with an optical profilometer for different loading conditions. Fatigue crack initiation life Ni and total fatigue life Nf were examined using standard surface topography parameters (such as, root...
-
Stability of trusses with linear elastic side-supports
PublikacjaThe present research is devoted to study of a lateral buckling of truss with linear elastic side supports. The elastic support reaction in relation to force in compressed chord and coefficient of buckling length related to side support distance are also calculated. The effect of slope of side support on limit force is also considered. The nonlinear analysis of two roof trusses are carried out. The results are compared to design...
-
Influence of Seeds’ Age and Clarification of Cold-Pressed Raspberry (Rubus idaeus L.) Oil on the DSC Oxidative Stability and Phase Transition Profiles
Publikacja -
The influence of rest interval on total training load during 10 sets of the bench press exercise performed to concentric failure
Publikacja -
Overcoming carboxylic acid inhibition by granular consortia in high-load liquefied food waste fermentation for efficient lactate accumulation
PublikacjaGranular sludge, a self-aggregating spherical biofilm, possesses better stability compared to flocculent sludge under extreme conditions. This study compared the ability of anaerobic granular sludge (AnGS) and flocculent waste activated sludge (WAS) to convert food waste (FW) into highly-valuable optically active lactic acid (LA), a central and versatile intermediate platform molecule. Different loadings (30–60 g volatile suspended...
-
Influence of pitting corrosion on fatigue and corrosion fatigue of ship and offshore structures. Part II: Load - pit crack interaction
PublikacjaIn the paper has been discussed influence of stresses on general corrosion rate and corrosion pit nucleation and growth rate, whose presence has been questioned by some authors but accepted by most of them. Influence of pit walls roughness on fatigue life of a plate suffering pit corrosion and presence of so called "non damaging" pits which never lead to initiation of fatigue crack, has been presented. Possibility of prediction...
-
ANALYSIS OF BRACE STIFFNESS INFLUENCE ON STABILITY OF THE TRUSS
PublikacjaThe paper is devoted to the numerical and experimental research of stability of a truss with side elastic supports at the top chord. The structure is a model of a real roof truss scaled by factor ¼. The linear buckling analysis and non-linear static analysis were carried out. The buckling length factor for the compressed top chord was calculated and the limit load for the imperfect truss shell model with respect to brace stiffness...
-
Report no: WOiO /II/46/2015 - Construction node verification test, estimation of breaking load (shear force) and destruction form
PublikacjaA new generation of tanks for LNG transportation has been designed. Mass reduction forced our customer to use three different materials: austenitic steel, aluminium alloy and LNG compressed wood between them. The expertise concerns structural node between tank foundation and suspension. Expertise contains: description of object of test, test principals, results and conclusions
-
Selected local stability problems of channel section flanges made of aluminium alloys
PublikacjaThe paper addresses the issue of local buckling of compressed flanges of cold-formed thin-walled channel columns and beams with nonstandard flanges composed of aluminium alloys. The material behaviour follows the Ramberg–Osgood law. It should be noted that the proposed solution may be also applied for other materials, for example: stainless steel, carbon steel. The paper is motivated by an increasing interest in nonstandard cold-formed...
-
The extended model predictive-sliding mode control of three-level AC/DC power converters with output voltage and load resistance variations
Publikacja -
Analiza numeryczna i badania doświadczalne wpływu usytuowania stężeń na nośność wyboczeniową modelu kratownicy
PublikacjaIn the present research the results of experimental test and numerical analyses of a model of a typical truss are presented. The truss linear buckling analysis and non linear static analyses with respect to material and geometrical nonlinearity are conducted. For different stiffnesses and location of braces, the critical load and limit load for the truss are calculated and the threshold bracing stiffness is found. The results of...
-
Wpływ azotowania jarzeniowego na niszczenie wodorowe stali przy stałym obciążeniu = Influence of plasma nitriding on steelhydrogen degradation under constant load
PublikacjaPrzedstawiono wyniki badań wpływu warstwy azotowanej jarzeniowo na podatność stali stopowej 34CrAlNi7-10 na niszczenie wodorowe, wyznaczoną w próbie stałego obciążenia w środowisku kwaśnym przy polaryzacji katodowej o gęstości prądu 1 mA/cm2.Określano odporność na pękanie w czasie 200 godz. dla obciążeń równych 0,88-0,96 siły zrywającej.
-
Stability of a truss under upward wind loading
PublikacjaThe present paper is devoted to the numerical investigations of stability of a truss under upward wind load. The truss is braced at its the upper cord. A structural variant including lateral braces, or lateral and torsional braces is considered. The research presents the problems of linear buckling and non-linear static analysis of the truss shell and beam model with geometric and material non-linearity are presented. The initial...
-
3D buckling analysis of a truss with horizontal braces
PublikacjaThe present research is devoted to the study of out-of-plane buckling of a truss with horizontal braces. The truss is a model of real roof truss scaled by factor ¼. A linear buckling and a non-linear analysis with geometric and material nonlinearity were carried out. The truss buckling and limit load for different stiffnesses and number of braces are found. Numerical analysis are verified by experiment. Threshold bracing stiffness...
-
3D Buckling Analysis of a Truss with Horizontal Braces
PublikacjaThe present research is devoted to the study of out–of–plane buckling of a truss with horizontal braces. The truss is a model of real roof truss scaled by factor 1=4. A linear buckling and a non–linear analysis with geometric and material non–linearity were carried out. The truss buckling and limit load for different stiffnesses and number of braces are found. Numerical analysis are verified by experiment. Threshold bracing stiffness condition...
-
The impact of material degradation on the resistance and reliability of truss structures
PublikacjaThe paper analyses limit load-carrying capacity and buckling load of truss towers used to support high voltage power lines. The analysed typical structure was subjected to characteristic loads and their combinations. The results were applied to assess structural resistance with regard to steel corrosion in the long-term operation. The extent of structural deterioration was assessed due to Young's modulus decrement in the course...
-
STABILITY ANALYSIS OF A TRUSS WITH SLOPING ELASTIC BRACES
PublikacjaSteel trusses have a much greater strength and stiffness in their plane than out of their plane, and therefore should be braced against lateral deflection and twisting. Such elements like purlins apart from bearing vertical load are part of bracing that stabilize roof trusses against distortional buckling. The stability of trusses with elastic bracing was investigated in an experimental research. Braces situated at some angle measured...
-
Stability of an imperfect truss loaded by wind
PublikacjaThe present paper is devoted to the numerical research of stability of a truss loaded by wind and stiffened by elastic supports located at the top chord. The lateral braces or lateral and torsional braces were taken into account. In this paper, the linear buckling analysis re- sults for the beam and shell model were presented. Two different shapes of initial geometric imperfections were considered in the non-linear static analysis...
-
The Point Estimate Method in a Reticulated Shell Reliability Analysis
PublikacjaThe objective of this paper is to present an application of the point estimate method (PEM) to determine the probabilistic moments for engineering structures. Reliability analysis is illustrated by two examples: an estimation of the critical force in linear elastic buckling analysis and a reticulated shell limit load determinations. Calculations were also made using Monte Carlo method. It has been shown the practical usefulness...
-
Sensitivity analysis of critical loads of I-columns
PublikacjaThe first order variation of critical buckling load of thin-walled columns with bisymmetric open cross-section due to some variations of the design variables such as: cross-section dimensions, or material characteristics is derived. The influence of the residual welding stresses is taken into account. In the numerical examples dealing with I-column the functions describing the effect of the variation of the dimensions of the flange...
-
Preliminary experimental research on stability of truss' joint with positive eccentricity
PublikacjaRecently, a very large interest in lightweight steel structures made from cold-formed sections has been noticeable. In the design practice, a large emphasis is put on rational shaping of both the thin-walled elements and constructions designed on them. The aim of this paper is to present the methodology for preparation of experimental research that model the behaviour of members in trusses made of cold-formed sections with positive...
-
Significant Decrease in Glycated Hemoglobin, 2h-Post-Load Glucose and High-Sensitivity C-Reactive Protein Levels in Patients with Abnormal Body Mass Index after Therapy with Manual Lymphatic Drainage
Publikacja -
Sensitivity analysis of critical forces of trusses with side bracing
PublikacjaThe present research is devoted to the study of out-of-plane buckling of trusses with elastic side bracing. Inthis paper, a sensitivity analysis of critical buckling loads of a truss due to bracing stiffness is carried out. A method based on the sensitivity analysis for the determination of the threshold bracing stiffness conditionfor full bracing of a truss is proposed. The influence lines of the unit change of the bracing stiffness...
-
Local buckling and initial post-buckling behaviour of channel member flange - analytical approach
PublikacjaThe local buckling and initial post-buckling behaviour of the cold-formed channel member flange is investigated. The governing nonlinear differential equation for axially compressed columns and beams undergoing pure bending is derived using the stationary total potential energy principle. The critical stress and initial post-buckling equilibrium path is determined by means of a perturbation approach. The results obtained allow...
-
PROBABILISTIC ANALYSIS OF A SPACE TRUSS BY MEANS OF A MULTIDIMENSIONAL VARIABLE DESCRIPTION
PublikacjaThe objective of this paper is to present a variant of the point estimate method (PEM) to determine mean values and standard deviations of limit loads of engineering structures. This approach is illustrated by limit state analysis of a space truss, considering geometric and material imperfections. The calculations were performed for different random models, so the influence of random parameters on the limit load of the truss can...
-
The validation process of truss model with joint eccentricities
PublikacjaNowadays, due to the technological reasons in modern lightweight steel trusses, fabricated from cold-formed sections, positive eccentricities appear in the truss nodes, to induce additional forces truss chords. In order to account for the real load-carrying capacity of truss node area the steel structure research was conducted in scale 1:1. As a result of experimental research, the forms of deformation and strains of the walls...
-
Vibro piles performance prediction using result of CPT
PublikacjaVibro piles belong to the group of full displacement piles with an expanded base, characterised by a very high load capacity, especially in non-cohesive soils. The problem is to adopt a reliable method for the determination of full load–settlement (Q–s) curve. A frequent difficulty is the determination of the load capacity limit based on the static load test because the course of the load–settlement curve is of a linear nature....
-
Comparison of classical Winter's bracing requirements of compressedtruss chord with stability analysis of 3D truss-model
PublikacjaMost code requirements concerning bracing are based on principles developed by Winter. The present research is devoted tostudy a lateral buckling of truss with linear elastic side supports. The classical Winter's model of truss chord in the case ofout of the truss plane buckling is compared with nonlinear analysis of 3D truss model. Full bracing condition, that permitsthe truss chord to support load level corresponding to an unbraced...
-
The point estimate method in a reticulated shell reliability analysis
PublikacjaThe objective of this paper is to present an application of the point estimate method (PEM) that can determine the probabilistic moments for engineering structures. The method is reasonably robust and adequately accurate for a wide range of practical problems. It is a special case of numerical quadrature based on orthogonal polynomials. The main advantage of this method is that, unlike FORM or SORM, it is not necessary to carry...
-
Investigation of buckling resistance of columns using non-linear static and dynamic analysis
PublikacjaThe aim of this paper is to investigate the stability process in an axially compressed column using a static and dynamic finite element analysis by taking both the geometric and material non-linearity into account. The perfect column and column with geometric imperfections were analysed. The linear buckling analyses were used to obtain the lowest buckling load and shapes of buckled forms that were taken into account as initial...
-
Application of linear buckling sensitivity analysis to economic design of cylindrical steel silos composed of corrugated sheets and columns
PublikacjaThe paper deals with global stability of steel cylindrical silos composed of corrugated walls and vertical columns with loads imposed by a bulk solid following Eurocode 1. The optimum silo design with respect to the steel weight was based on a sensitivity analysis method. The changes of silo column profiles at each design step were performed by means of influence lines for the buckling load factor due to the unit column bending...
-
Thin-walled cross section shape influence on steel member resistance.
PublikacjaThis work describes why trending thin-walled technology is achieving popularity in steel construction sector. A purpose of this article is to present the influence of the cold-formed element cross-section shape on an axial compression and a bending moment resistance. The authors have considered four different shapes assuming constant section area and thickness. Calculations were based on three different steel grades taking into...
-
Application of Barkhausen method to determine internal stresses in cold-rolled and hot-rolled sheets
PublikacjaThe paper presents investigations on internal stress distribution in plane hot—or cold-rolled sheets dedicated for the cold-formed profiles. The motivation of the research is a new profile design whose bending technology, incorporating a longitudinal welded joint and hot-dip galvanization after bending and welding introduces additional internal stresses. In order to identify the entirety of stresses in the process of sheet production...
-
COMPUTER-AIDED CONSTRUCTION AT DESIGNING REINFORCED CONCRETE COLUMNS AS PER EC
PublikacjaThe article presents the author’s computer program for designing and dimensioning columns in reinforced concrete structures taking into account phenomena affecting their behaviour and information referring to design as per EC. The computer program was developed with the use of C++ programming language. The program guides the user through particular dimensioning stages: from introducing basic data such as dimensions, concrete...
-
TRUSS JOINT WITH POSITIVE ECCENTRICITY EXPERIMENTAL RESEARCH
PublikacjaDue to the technological reasons in modern lightweight steel trusses, fabricated from cold- formed sections, positive eccentricities appear in the truss nodes what induce additional forces in the truss chords. To account for the real load-carrying capacity of truss node area the steel structure research in scale 1:1 were conducted. The experiments consisted of two parts: preliminary and proper one, when conclusions from...
-
Flexomagnetic response of buckled piezomagnetic composite nanoplates
PublikacjaIn this paper, the equation governing the buckling of a magnetic composite plate under the influence of an in-plane one-dimensional magnetic field, assuming the concept of flexomagnetic and considering the resulting flexural force and moment, is investigated for the first time by different analytical boundary conditions. To determine the equation governing the stability of the plate, the nonlocal strain gradient theory has been...