Filtry
wszystkich: 1317
wybranych: 1087
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: FIN-TUBE HEAT EXCHANGER, HEAT TRANSFER
-
Pipeline System for Heat Transportation from Nuclear Power Plant – an Optimizing Approach
PublikacjaOver the last few years heat piping insulation technology and pump systems efficiency have been significantly improved. Reduced thermal losses encourage heat transportation over long distances. It provides an opportunity for increasing thermodynamic efficiency of Nuclear Power Plants (NPPs) that are often located in rural areas because of safety issues. It can be achieved by Combined Heat and Power (CHP) generation, as heat produced...
-
Effect of asymmetric fluid flow distribution on flow boiling in a microchannel heat sink – An experimental investigation
PublikacjaFlow boiling in microchannels is emerging as an exclusive cooling solution for miniaturized high-power electronic devices alongside having other high heat flux applications. Size miniaturization at microscale strangely increases heat transfer performance as well as flow boiling instabilities. Many flow boiling instabilities are interrelated and result from imperfect hydrodynamic conditions. One of such problems is flow maldistribution among...
-
Analytical method for calculation of heat source temperature drop for the Organic Rankine Cycle application
PublikacjaIn the paper presented are considerations on the cooperation of the limited capacity heat source with the Organic Rankine Cycle unit. Usually the heat source providing thermal energy to the Organic Rankine Cycle (ORC) may have twofold characteristics. It can be in the form of a single phase fluid, i.e. as hot exhaust gas or hot liquid, or in some cases it may be available as a phase changing fluid, as for example, technological...
-
Heat Transfer Augmentation through Different Jet Impingement Techniques: A State-of-the-Art Review
Publikacja -
Determination of heat transfer coefficient in evaporator of the organic Rankine cycle using the Wilson method.
PublikacjaW pracy zastosowano metodę Wilsona do wyznaczania współczynnika przejmowania ciepła. Przedmiotem rozważań jest płytowy wymiennik ciepła pracujący jako parownik w laboratoryjnym stanowisku realizującym obieg ORC. Wykorzystana metoda jest metodą wydajną w przypadku wymienników ciepła o złożonej geometrii i dużej liczbie kanałów, dla których pomiar temperatury ścianki jest niemożliwy, a przez to określenie współczynników przejmowania...
-
Natural convective heat transfer from isothermal horizontal, vertical and inclined plates - a review
PublikacjaW artykule przedstawiono przegląd otrzymanych przez różnych badaczy korelacji eksperymentalych, teoretycznych i numerycznych, opisujących wymianę ciepła od izotermicznych płyt o różnym kącie pochylenia. Przedstawiono model matematyczny zjawiska. Opisano stosowane metody badawcze i wskazano przyczyny rozbieżności pomiędzy przedstawionymi przez wielu autorów wynikami.
-
The use of liquid crystal thermography and particle image velocimetry in the exploration of heat transfer measurements
PublikacjaArtykuł dotyczy badań eksperymentalnych wymiany ciepła w modelowym wymienniku ciepła z turbulizatorami przepływu przy użyciu termografii ciekłokrystalicznej i cyfrowej anemometrii obrazowej.
-
Intensyfikacja wymiany ciepła przy pomocy mikrostrug = Heat transfer intensification using microjets.
PublikacjaW pracy przedstawiono wyniki badań eksperymentalnych nad intensyfikacją strumienia ciepła przy pomocy pojedynczej mikrostrugi wody. W pracy przedstawiono wyniki badań dla dysz o średnicy 180 i 280 mikrometrów.
-
Influence of porous coating on heat transfer during flow boiling of R22, R134a and R407C
PublikacjaPrzedstawiono wpływ pwłoki porowatej w pozionej rurce podczas wrzenia w przepływie i spadku ciśnienia czynników chłodniczych R22, R134a i R407C.
-
Free convective heat transfer structures as a function of the width of isothermal horizontal rectangular plates
PublikacjaZaprezentowano rezultaty badań eksperymentalnych konwekcyjnej wymiany ciepła od izotermicznych płyt prostokątnych skierowanych ku górze. Na podstawie przeprowadzonych wizualizacji zaproponowano dwa modele struktur przepływu. Rozwiązania analityczne dla tych modeli przedstawiono w postaci zależności liczb Nusselta Rayleigh'a. Stwierdzono, że przepływ koncentryczny występuje dla małych wartości liczb Ra, szczególnie w przypadku płyt...
-
AN OVERVIEW OF HEAT TRANSFER ENHANCEMENT BASED UPON NANOPARTICLES INFLUENCED BY INDUCED MAGNETIC FIELD WITH SLIP CONDITION VIA FINITE ELEMENT STRATEGY
PublikacjaThe mathematical model of heat generation and dissipation during thermal energy transmission employing nanoparticles in a Newtonian medium is investigated. Dimensionless boundary layer equations with correlations for titanium dioxide, copper oxide, and aluminium oxide are solved by the finite element method. Parameters are varied to analyze their impact on the flow fields. Various numerical experiments are performed consecutively...
-
Towards enhanced heat and mass exchange in adsorption systems: The role of AutoML and fluidized bed innovations
Publikacja -
Underwater in situ local heat treatment by additional stitches for improving the weldability of steel
PublikacjaIn this paper the influence of in situ local heat treatment performed by additional stitches on the weldability of high-strength low-alloy (HSLA) S355J2C+N steel was tested. The investigated steel is characterized by high susceptibility to cold cracking. It is necessary to find a method to improve the quality of welded joints. The local heat treatment was applied as an eect of bead-on plate welding made on the face of a Tekken...
-
Technical and economic conditions of supplying residential consumers with heat from nuclear power plant
PublikacjaThe reduction of CO2 emission requires technological shift towards carbon-free options. Cogeneration of electricity and heat based on coal and natural gas will experience generation cost increase, if the costs of emissions are imposed on the plant operators. Therefore, nuclear and renewable options should be considered. In this paper, we present the concept of electricity and heat supply system with nuclear condensing turbine adapted...
-
The Laboratory Stand for the Evaluation of Heat Dissipation from the Power Cable in a Casing Pipe
PublikacjaThe current carrying capacity of a power cable determines its efficiency, which depends on its capability to dissipate heat produced inside the cable, as a result of current flow, into the surrounding. The studies were conducted to determine how the characteristics of the medium around the cable affected its temperature and, as a result, its ability to transport electricity. The experimentation in the lab and real measurements...
-
The impact of environmentally friendly refrigerants on heat pump efficiency
PublikacjaThis paper discusses the issue of heat pump simulation. Lower operating costs can be achieved through good equipment design and appropriate operation. Detailed technical and economic analysis inform the selection of system components with the highest possible efficiency and lower energy demand. The use of systems based on environmentally friendly refrigerants can deliver long product life, which is associated with a shorter payback...
-
THE THERMODYNAMIC ANALYSIS OF THE SZEWALSKI HIERARCHIC VAPOUR CYCLE COOPERATED WITH THE SYSTEM OF HEAT RECOVERY
PublikacjaIn this paper, thermodynamic analysis of the Szewalski hierarchic vapour cycle cooperated with the system of heat recovery from exhaust gases are presented. According to that purpose, the CFM (Computation Flow Mechanics [1,3]) approach has correctly been used. The whole system consists of the first traditional steam cycle, the second organic Rankine cycle (ORC) and system of heat recovery with use of water with temperature 90...
-
Investigation of the influence of capilary effect on operation of the loop heat pipe
PublikacjaIn the paper presented are studies on the inestigation of the capillary forces effect inducted in the porous structure of a loop heat pipe using water and ethanol ad test fluids. The potential application of such effects is for example in the evaporator of the domestic micro-CHP unit, where the reduction of pumping power could be obtained. Preliminary analysis of the results indicates water as having the best potential for developing...
-
Evaluation of technical efficiency of heat and electric power generation
PublikacjaThis paper presents an evaluation of technical efficiency and time-dependent changes in productivity of Polish professional electric power and heat&electric power stations by using Data Envelopment Analysis non-parametric method. The research covered the enterprises whose total available electric power amounted to about 98% of that of all professional thermal electric power stations in this country. The analysis has concerned...
-
Thermal Energy Development in Magnetohydrodynamic Flow Utilizing Titanium Dioxide, Copper Oxide and Aluminum Oxide Nanoparticles: Thermal Dispersion and Heat Generating Formularization
PublikacjaThe main aim of this article heat transfer in thermal engineering deals with the production, use, transformation, and transfer of thermal energy. Engineering and industrial fields including food packaging, the production of food additives, electronic cooling, microturbines, etc. heavily rely on heat transmission. Due to its intriguing potential in industries like the production of polymers, paper, crystal glass, etc., scientists...
-
Pool Boiling of Water–Al2O3 and Water–Cu Nanofluids Outside Porous Coated Tubes
PublikacjaThis paper deals with pool boiling ofwater–Al2O3 and water–Cu nanofluids on porous coated, horizontal tubes. Commercially available stainless-steel tubes having 10 mm outside diameter and 0.6 mm wall thickness were used to fabricate a test heater. Aluminum porous coatings 0.15 mm thick with porosity of about 40% were produced by plasma spraying. A smooth tube served as a reference tube. The experiments were conducted under different...
-
Operation of the 900 MW power plant with the ORC supplied from three heat sources
PublikacjaThe chapter is aimed at utilisation of waste heat in the reference supercritical power plant in the manner to produce electricity in ORC installation. The waste heat is available in the form of a stream of hot water at 90°C, recovered from the exhaust gases in the amount of 200MW. Such low enthalpy heat source is rather insufficient to produce a good quality vapour to feed the ORC turbine. Therefore an original approach to increase...
-
The In-House Method of Manufacturing a Low-Cost Heat Pipe with Specified Thermophysical Properties and Geometry
PublikacjaVarious types of heat pipes are available to purchase off the shelf, from various manufacturers, but most of them have strictly defined geometry and technical parameters. However, when there is a need to use a heat pipe (HP) with an unusual size and shape or working conditions other than the standard ones, it becomes very costly to order them from manufacturers, especially in small quantities, and only a few producers are willing...
-
Correlation between Compressive Strength and Heat of Hydration of Cement Mortars with Siliceous Fly Ash
PublikacjaThis paper presents the results of calorimetric and strength tests of mortars with ordinary Portland cement and two substitution rates (10 and 20%) of cement by siliceous fly ash. The prepared samples were cured under isothermal conditions at four different temperatures: 23, 33, 43 and 53 °C. Heat of hydration was measured using an isothermal calorimeter dedicated to monitor the hydration process of cementitious composites such...
-
Particulate Matter Production of Small Heat Source Depending on the Bark Content in Wood Pellets
PublikacjaWood pellets as biofuel are more and more used in small heat sources in Europe. Standard wood pellets are produced from wood sawdust without bark. The paper deals about the impact of bark in wood pellets on their properties and combustion process. Special attention in this work is paid to production of particulate matter during combustion of wood pellets depending on bark content. There were experimentally produced spruce wood...
-
Optimization of combined heat and power (CHP) market allocation: The case of Poland
PublikacjaCombined heat and power (CHP), that is production of electricity and useful heat in a single thermodynamic process, is a way of primary energy saving and emission reduction. Therefore, promotion of the electricity from high-efficiency cogeneration (CHP-E) was encouraged in the European Union. However, CHP-E promotion mechanisms proved low effectiveness in certain countries, like Poland, where the prices of certificates of origin...
-
Heat transfer to car engine cooling system - influence of coolant flow through engine block
PublikacjaW artykule przedstawiono wyniki badań doświadczalnych nad wpływem nastawianej wydajności pompy cieczy na strumień odbieranego ciepła w silniku spalinowym. Wykorzystano hamownię silnikową z silnikiem o zapłonie iskrowym o objętości skokowej 1.8 dm^3. Przyjęto obciążenia silnika oporami ruchu samochodu na biegu bezpośrednim.
-
A semi-empirical method for calculation of heat transfer coefficient in flow boiling for conventional tubes and minichannels
PublikacjaW pracy przedstawiono zagadnienia które należy uwzględnić podczas modelowania wymiany ciepła z wrzeniem w przepływie w kanałach o małej średnicy. Uzyskano dobrą zgodność z wynikami badań eksperymentalnych.
-
A semi-empirical method for calculation of heat transfer coefficient in flow boiling for conventional tubes and minichannels
PublikacjaW pracy przedstawiono zagadnienia któe należy uwzględnić podczas modelowania wymiany ciepła z wrzeniem w przepływie w kanałach o małej średnicy. Uzyskano dobrą zgodność z wynikami badań eksperymentalnych.
-
Implementation of Fluidized Bed Concept to Improve Heat Transfer in Ecological Adsorption Cooling and Desalination Systems
Publikacja -
Experimental and numerical simulations of flow and heat transfer in heatexchanger elements using liquid crystal thermography.
PublikacjaPrzedstawienie koncepcji badań eksperymentalnych i numerycznych oraz ich wyników podczas wymiany ciepła w modelach klasycznych i płytowych wymienników ciepła w warunków przepływów przejściowych i turbulentnych.
-
ATTEMPTS OF THERMAL IMAGING CAMERA USAGE IN ESTIMATIONS OF THE CONVECTIVE HEAT LOSS FROM A VERTICAL PLATE
PublikacjaIn this paper a new method for determining heat transfer coefficients using a gradient method has been developed. To verify accuracy of the proposed method vertical isothermal heating plate with natural convection mechanism has been examined. This configuration was deliberately chosen, because of the fact that such case is historically the earliest and most thoroughly studied and its rich scientific documentation - the most reliable....
-
Two-phase optimizing approach to design assessments of long distance heat transportation for CHP systems
PublikacjaCogeneration or Combined Heat and Power (CHP) for power plants is a method of putting to use waste heat which would be otherwise released to the environment. This allows the increase in thermodynamic efficiency of the plant and can be a source of environmental friendly heat for District Heating (DH). In the paper CHP for Nuclear Power Plant (NPP) is analyzed with the focus on heat transportation. A method for effectivity and feasibility...
-
Photovoltaic Roof Tiles: The Influence of Heat Recovery on Overall Performance
PublikacjaA photovoltaic (PV) roof tile serves both as a roofing material and as an electricity-producing surface. The main aim of the present study was to increase the overall system efficiency of PV tiles by using heat recovery. The chosen strategy was two-fold: determine the operational efficiency of PV tiles and optimize construction to increase the cooling effect when using air as the working medium. A detailed experimental study was...
-
Modeling of heat and fluid flow in granular layers using high-order compact schemes and volume penalization method
Publikacja -
Preliminary results from HEDGEHOG REXUS Project - sounding rocket experiment on accelerations, vibrations and heat flow
PublikacjaAs access to space conditions becomes more available, both technically and economically, scientists' interest in launching finer and more sophisticated experiments grows. This applies now more than ever to fragile by nature biological and chemical experiments. To be qualified for launch, such experiments need to be carefully tested prior to the event. The tests should represent actual launch conditions as closely and in as detailed...
-
Experiment-Based Study of Heat Dissipation from the Power Cable in a Casing Pipe
PublikacjaThe paper deals with the important challenges in terms of electricity transmission by means of underground cable lines. The power cable’s performance is characterized by an ampacity that represents its maximum electric current-carrying capacity. The ampacity of power cables depends on their ability to diffuse the heat generated by the current flow into the environment. In the performed research, the analysis of the efficiency of...
-
Investigation on polypropylene friction stir joint: effects of tool tilt angle on heat flux, material flow and defect formation
PublikacjaTool tilt angle (TTA) is a critical factor that can control material flow in polymeric materials' friction stir joining (FSJ). This study selected a TTA range between 0° to 4° for FSJ of polypropylene (PP) polymer sheet. A modified computational fluid dynamic (CFD) technique was implemented to gain a deep understanding of the effects of TTA during FSJ of PP. The PP joint's internal flow, defect formation, heat generation, and tensile...
-
Analysis of possibility and purposefulness of application of waste-heat boilers to trailing suction hopper dredgers
PublikacjaThis paper presents an analysis of possibility and purposefulness of application of waste-heat boilers to trailing suction hopper dredgers. Using results of own operational research on dredgers this author determined thermal power demand for six hypothetical trailing suction hopper dredgers of various size, at accounting for a type of power system and kind of fuel combusted by dredger's power plant. By means of basic indices of...
-
Wyznaczanie współczynnika przejmowania ciepła podczas wrzenia w przepływie dwutlenku węgla (Prediction of flow boling heat transfer coefficient for carbon dioxide in minichannels)
PublikacjaW pracy przedstawiono wyniki obliczeń uzyskane za pomocą własnego modelu półemirycznego dla wybranych danych eksperymentalnych dla wrzenia w przepływie dwutlenku węgla. Metoda obliczeniowa została zweryfikowana z danymi eksperymentalnymi Docoulombiera i innych (2011) oraz Mastrullo i innych (2009). Badania eksperymentalne dotyczą pełnego zakresu zmienności stopnia suchości oraz zakresu prędkości masowej G=200-1200 kg/m2s. rozwijany...
-
Influence of Cement Replacement with Sewage Sludge Ash (SSA) on the Heat of Hydration of Cement Mortar
PublikacjaThe amount of fly ash from the incineration of sewage sludge is increasing all over the world, and its utilization is becoming a serious environmental problem. In the study, a type of sewage sludge ash (SSA) collected directly from the municipal sewage treatment plant was used. Five levels of cement replacement (2.5%, 5%, 7.5%, 10% and 20%) and unchanged water-to-binder (w/b) ratio (0.55) were used. The purpose of the study was...
-
Heat recovery from the hybrid photovoltaic tile – experimental studies with the solar light simulator
PublikacjaConsidering the current development of micro-cogeneration energy sources, supported by the national prosumer policy and the act on the renewable energy sources, there is a great demand for the effective solar technologies. In this area, the photovoltaic cells with a combined conversion of the solar radiation energy into the electrical and thermal energy (PV/T cells) seem to be attractive. They are already widely available and treated...
-
Experimental Investigation of the Thermal Performance of a Wickless Heat Pipe Operating with Different Fluids: Water, Ethanol, and SES36. Analysis of Influences of Instability Processes at Working Operation Parameters
PublikacjaIn this study, the influences of different parameters on performance of a wickless heat pipe have been presented. Experiments have been carried out for an input power range from 50 W to 300 W, constant cooling water mass flow rate of 0.01 kg/s, and constant temperature at the inlet to condenser of 10 C. Three working fluids have been tested: water, ethanol, and SES36 (1,1,1,3,3-Pentafluorobutane) with different filling ratios (0.32,...
-
Heat generation by impulse ultrasound.
PublikacjaOryginalna metoda zastosowana dla wyprowadzenia równaniaewolucyjnego dla ogrzewania środowiska przez falę akustycznądowolnej natury, w tym nieokresowej. Przedstawiono przykłady obliczeń numerycznych.
-
Additive Manufacturing as a Solution to Challenges Associated with Heat Pipe Production
PublikacjaThe aim of this review is to present the recent developments in heat pipe production, which respond to the current technical problems related to the wide implementation of this technology. A novel approach in HP manufacturing is to utilise hi-tech additive manufacturing techniques where the most complicated geometries are fabricated layer-by-layer directly from a digital file. This technology might be a solution to various challenges...
-
Study of the Influence of Heat Convection Coefficient on Predicted Performance of a Large Tilting-Pad Thrust Bearing
PublikacjaPart of the heat generated by the shearing of the lubricating film during operation of a hydrodynamic bearing is transferred to the bearing components. In the case of the pad, which is usually fully submerged in the lubricating oil, heat is further transferred at the pad free walls to the oil by convection. This mechanism causes a thermal gradient in a pad and, consequently, its thermal deflection. In large hydrodynamic thrust...
-
Preliminary results from HEDGEHOG REXUS project – A sounding rocket experiment on accelerations, vibrations and heat flow
PublikacjaDuring flight, a sounding rocket is subject to a unique environment - severe vibrations and substantial heat flux. In order to design payloads, precise measurement of these conditions is required. This paper presents preliminary results from HEDGEHOG REXUS Project, whose scientific goal was to characterise the thermal and dynamic environment of REXUS sounding rockets. For this purpose, two new sensors have been designed - mechanical...
-
Comparison of traditional district heating with low temperature district heating systems featuring organic Rankine cycle and heat pump
PublikacjaPaper presents a comparison between a traditional district heating system with conventional boilers as a source of heat and electricity purchases from power utilities and a low temperature DH system incorporating the CHP with organic Rankine Cycle providing electricity and local heat pump raising the temperature of the DH fluid to the required temperature in the dwelling, meaning that both heat and electricity are produced within...
-
Numerical solution analysis of fractional point kinetics and heat exchange in nuclear reactor
PublikacjaThe paper presents the neutron point kinetics and heat exchange models for the nuclear reactor. The models consist of a nonlinear system of fractional ordinary differential and algebraic equations. Two numerical algorithms are used to solve them. The first algorithm is application of discrete Grünwald-Letnikov definition of the fractional derivative in the model. The second involves building an analog scheme in the FOMCON Toolbox...
-
Numerical simulation of temperature distribution of heat flow on reservoir tanks connected in a series
PublikacjaThe flow of temperature distribution through a medium in thermodynamic studies plays an important role in understanding physical phenomena in chemical science and petroleum engineering, while temperature distribution indicates the degree of reaction that must be undergone to obtain the final product. Therefore, this paper aims to present and apply the exponential matrix algorithm (EMA), differential transformation algorithm (DTA),...