Wyszukiwarka
Filtry
wszystkich: 752
wybranych: 683
-
Katalog
Filtry wybranego katalogu
Wyniki wyszukiwania dla: rapid prototyping propeller
-
Hip endhoprothesis development using rapid prototyping methods
PublikacjaIntegrated product development based on Rapid Prototyping methods, connected with computer aided 3D design and computer aided engineering enables fast and full new product verification and validation. A case study derived from clinical and technological practice using hip implant construction is also included.
-
Product development using rapid prototyping for pump rotors
PublikacjaW artykule zaprezentowano zastowanie techniki szybkiego prototypowania do wytwarzania fizycznych modeli produktów i ich części składowych oraz prototypów funkcjonalnych, technicznych i wizualnych z pominięciem tradycyjnych technologii mechanicznych jak odlewanie, skrawanie czy też obróbko elektroerozyjna. Przedstawione studium przypadku oparto na rozwoju konstrukcji wirnika pompy począwszy od etapu projektowania poprzez wytwarzanie...
-
Impeller pump development using rapid prototyping methods
PublikacjaMetody szybkiego prototypowania przy wspomaganiu komputerowym projektowania 3D wraz z systemami wspomagania inżynierskiego pozwalają uzyskać wyrób o prognozowanych właściwościach technologicznych i użytkowych.W artykule przedstawiono studium przypadku zastosowania metod szybkiego prototypowania w rozwoju elementów pomp wirowych.
-
Deformation of the Structural Details of the Components Created by the Rapid Prototyping Method
PublikacjaThe paper present the results of preliminary research and describes the deformation of construction details within the process of producing small element employing a stereography system. The article discuses a scheme for changes in data conversion. Variation in construction details have been described on the basis of analysing photographs.
-
Tip-Based Nanofabrication as a Rapid Prototyping Tool for Quantum Science and Technology
PublikacjaTip-Based Nanofabication as a Rapid Prototyping Tool for Quantum Science and Technology discusses the development of cantilevered nanotips techniques of quantum devices prototyping and how they evolved from scanning probe microscopy. Also covered are the advantages and future prospects of atomic resolution capability and how to use this enabling technology as a rapid prototyping tool for quantum science and technology.
-
The application of a photopolymer material for the manufacture of machine elements using rapid prototyping techniques
PublikacjaThe paper discusses the application of polymer resin for 3D printing. The first section focuses on rapid prototyping technique and properties of the photopolymer, used as input material in the manufacture of machine components. Second part of the article was devoted to exemplary 3-D-printed elements for incorporation in machines. The article also contains detailed description of problems encountered in implementation of the selected...
-
Application of Rapid Prototyping technology in the manufacturing of turbine blade with small diameter holes
PublikacjaThe article presents the possibilities of using Rapid Prototyping (RP) technology in the manufacturing of turbine blades with small diameter holes. The object under investigation was gas turbine blade with small diameter cooling holes and holes for generating longitudinal vortices. A turbine blade model was produced by means of Direct Metal Laser Sintering (DMLS) technology and subsequently validated in terms of detection and accuracy...
-
A Microwave Sensor with Operating Band Selection to Detect Rotation and Proximity in the Rapid Prototyping Industry
PublikacjaThis paper presents a novel sensor for detecting and measuring angular rotation and proximity, intended for rapid prototyping machines. The sensor is based on a complementary split-ring resonator (CSRR) driven by a conductor-backed coplanar waveguide. The sensor has a planar topology, which makes it simple and cost-effective to produce and accurate in measuring both physical quantities. The sensor has two components, a rotor, and...
-
Techniki szybkiego prototypowania w budowie maszyn = Rapid prototyping techniques in machine building
PublikacjaW artykule omówiono przygotowanie oraz wykonanie poszczególnych elementów maszyn za pomocą techniki szybkiego prototypowania. W pierwszej części przedstawiono technologię wydruku przestrzennego oraz właściwości materiału budulcowego. Druga część artykułu została poświęcona przykładowym wydrukom i ich zastosowaniom w maszynach.
-
Experimental study on the effect of selected sterilization methods on mechanical properties of polylactide FFF specimens
PublikacjaPurpose: Biodegradable polymers are widely used in personalized medical devices or scaffolds for tissue engineering. The manufacturing process should be finished with sterilization procedure. However, it is not clear how the different sterilization methods have an impact on the mechanical strength of the three-dimensional (3D)-printed parts, such as bone models or personalized mechanical devices. This paper aims to present the...
-
A pilot study to assess an in-process inspection method for small diameter holes produced by Direct Metal Laser Sintering
PublikacjaPurpose The purpose of this research is to evaluate the geometric quality of small diameter holes in parts printed by DMLS technology. An in-process optical inspection method is proposed and assessed during a pilot study. The influence of the theoretical hole diameter assumed in a CAD system and the sample thickness (hole length) on the hole clearance was analysed. Design/methodology/approach The samples made of two different...
-
CFD and FEM model of an underwater vehicle propeller
PublikacjaDuring the project execution of design and optimization the Remotely Operated Vehicle (ROV) research on its propulsion has been carried out. The entire project was supported by CFD and FEM calculations, which taking into account the characteristics of underwater vehicle. One of the tasks was to optimize the semi-open duct for horizontal propellers, which provided propulsion and controllability in horizontal plane. In order to...
-
Developments in manufacturing engineering and machining process planning
PublikacjaCurrent research conducted in the Department of Manufacturing Engineering and Automation is presented in the paper. This includes: abrasive cutting off, grinding with lapping kinematics, rapid prototyping and machining procrss planning. Experimental results and computer simulation are presented and analysed.
-
Experimental research on water lubricated marine stern tube bearings in conditions of improper lubrication and cooling causing rapid bush wear
PublikacjaWater lubricated bearings are popular in sliding bearings of marine propeller shafts, turbines and pump shafts. Such popularity is partly due to their simple construction which also means a relatively affordable price. In practical experience one may also observe cases of rapid wear or even malfunctions of this bearings, some of which may be caused by insufficient flow of lubricant leading to overheating. The conducted...
-
Przegląd metod szybkiego prototypowania algorytmów uczenia maszynowego w FPGA
PublikacjaW artykule opisano możliwe do wykorzystania otwarte narzędzia wspomagające szybkie prototypowanie algorytmów uczenia maszynowego (ML) i sztucznej inteligencji (AI) przy użyciu współczesnych platform FPGA. Przedstawiono przykład szybkiej ścieżki przy realizacji toru wideo wraz z implementacją przykładowego algorytmu prze-twarzania w trybie na żywo.
-
Two dimensional inverse solution for diagonal pumps
PublikacjaW pracy przedstawiono rozwiązanie zadania odwrotnego dla wirnika i kierownicy pompy diagonalnej. Dla założonego kształtu powierzchni prądu wyznaczono kształt łopatek obu palisad. Geometria kanałów łopatkowych została wyznaczona w wyniku rozwiązania układu równań zapisanych w krzywoliniowym układzie współrzędnych. W pracy przedstawiono fotografie wirnika wykonanego techniką Rapid Prototyping.
-
Surface Structure of Components Created by Stereolitography
PublikacjaStereolithography is an additive rapid prototyping method. This method is based on the principle of solidifying a liquid photopolymer (resin) by laser radiation. Models obtained with this method are characterized by a specific surface structure called “stairstep effect”. It causes that, the surface should be processed by additional finishing (postprocessing). To minimize the additional machining process, the model should be set...
-
Mechatronic design o strongly nonlinear systems on a basis of three wheeled mobile platform
PublikacjaRemarkable grow in demand both of mobile platform operability performance and reduction of project leading time development encourage to apply modern algorithms and reliable engineering tools for the design process. The paper discusses the mechatronic design applied for the surveillance system based on the energy performance index algorithm. The exploited mechatronic techniques i.e. virtual prototyping, Hardware-In-the-Loop Simulation...
-
Pantographic metamaterials: an example of mathematically driven design and of its technological challenges
PublikacjaIn this paper, we account for the research efforts that have been started, for some among us, already since 2003, and aimed to the design of a class of exotic architectured, optimized (meta) materials. At the first stage of these efforts, as it often happens, the research was based on the results of mathematical investigations. The problem to be solved was stated as follows: determine the material (micro)structure governed by those...
-
Możliwości poprawy sprawności pomp głębinowych HYDRO-VACUUM SA drogą zastosowania nowoczesnych komputerowych metod projektowania
PublikacjaW prezentacji omówiono algorytm postępowania jaki został zrealizowany przy modernizacji istniejącej konstrukcji pompy głębinowej. Modernizacji dokonano przy użyciu nowoczesnych metod komputerowych z wykorzystaniem własnego oprogramowania do obliczeń jedno i dwu-wymiarowych oraz komercyjnych programów CAD i do obliczeń przepływów 3D (Fluent). Porównano wyniki badań na konstrukcji rzeczywistej z badaniami numerycznymi konstrukcji...
-
Computer-Aided Greenery Design—Prototype Green Structure Improving Human Health in Urban Ecosystem
PublikacjaIncreasing population and urbanization, with climate change consequences, such as rising temperatures, influence public health and well-being. The search to improve the quality of life in cities becomes one of the priority objectives. A solution can be found in the role of greenery in an urban environment and its impact on human health. This opens a path toward experimentation on microclimate green structures that can be inserted...
-
Mechatronics design, modelling and controlling of the Stewart-Gough platform
PublikacjaThis paper presents a mechatronics design of a low cost Stewart-Gough platform (SGP) with rotary actuators. The designed SGP is supposed to be applied in a ball & plate control system. The synthesis of the ball & plate control system is also within the subject of the paper. A mechatronics design process of the SGP was conducted with computer-aided design (CAD) software. Unique analytical solutions of an inverse kinematics problem...
-
Materials Design for the Titanium Scaffold Based Implant
PublikacjaThe main objective of here presented research is a design the scaffold/porous titanium(Ti) alloy based composite material demonstrating better biocompatibility, longer lifetime andbioactivity behaviour for load-bearing implants. The development of such material is proposed bymaking a number of consecutive tasks. Modelling the mechanical, biomechanical and biologicalbehavior of porous titanium structure and an elaboration of results...
-
Materials Design for the Titanium Scaffold Based Implant
PublikacjaThe main objective of here presented research is a design the scaffold/porous titanium(Ti) alloy based composite material demonstrating better biocompatibility, longer lifetime andbioactivity behaviour for load-bearing implants. The development of such material is proposed bymaking a number of consecutive tasks. Modelling the mechanical, biomechanical and biologicalbehavior of porous titanium structure and an elaboration of results...
-
Polymer journal bearings behaviour research under limited lubrication and cooling conditions conducted on high torque test rig
PublikacjaPolymer journal bearings are frequently used as a water-lubricated bearings of small marine units’ propeller shafts . Choice of these bearings is based on their simple construction and relatively low purchase and maintenance costs. Although properly designed and installed water lubricated bearings may well last for over a decade, rapid wear or failure of these bearings can be observed...
-
POM/EVA Blends with Future Utility in Fused Deposition Modeling
PublikacjaPolyoxymethylene (POM) is one of the most popular thermoplastic polymers used in the industry. Therefore, the interest in its potential applications in rapid prototyping is understandable. Nevertheless, its low dimensional stability causes the warping of 3D prints, limiting its applications. This research aimed to evaluate the effects of POM modification with ethylene-vinyl acetate (EVA) (2.5, 5.0, and 7.5 wt.%) on its processing...
-
Efficient knowledge-based optimization of expensive computational models using adaptive response correction
PublikacjaComputer simulation has become an indispensable tool in engineering design as they allow an accurate evaluation of the system performance. This is critical in order to carry out the design process in a reliable manner without costly prototyping and physical measurements. However, high-fidelity computer simulations are computationally expensive. This turns to be a fundamental bottleneck when it comes to design automation using numerical...
-
Multi-region fuzzy logic controller with local PID controllers for U-tube steam generator in nuclear power plant
PublikacjaIn the paper, analysis of multi-region fuzzy logic controller with local PID controllers for steam generator of pressurized water reactor (PWR) working in wide range of thermal power changes is presented. The U-tube steam generator has a nonlinear dynamics depending on thermal power transferred from coolant of the primary loop of the PWR plant. Control of water level in the steam generator conducted by a traditional PID controller...
-
Performance and Emission Modelling and Simulation of Marine Diesel Engines using Publicly Available Engine Data
PublikacjaTo analyse the behaviour of marine diesel engines in unsteady states for different purposes, for example to determine the fuel consumption or emissions level, to adjust the control strategy, to manage the maintenance, etc., a goal-based mathematical model that can be easily implemented for simulation is necessary. Such a model usually requires a wide range of operating data, measured on a test stand. This is a time-consuming process...
-
Impact of Propeller Emergence on Hull, Propeller, Engine, and Fuel Consumption Performance in Regular Head Waves
PublikacjaIn this study, the impact of propeller emergence on the performance of a ship (speed), propeller (thrust, torque, and RPM), a diesel engine (torque and RPM) and fuel consumption are analysed under severe sea conditions. The goal is to describe the variation in the system variables and fuel consumption rather than analysing the motion of the ship or the phenomenon of propeller ventilation in itself. A mathematical model of the...
-
LABORATORIUM SZYBKIEGO PROTOTYPOWANIA : Inżynieria odwrotna
PublikacjaSzybkie prototypowanie (ang. Rapid Prototyping) i inżynieria odwrotna (ang. Reverse Engineering) są jednymi z najbardziej dynamicznie rozwijających się działów komputerowego wspomagania projektowania, wytwarzania i realizacji prac inżynierskich (CAD/CAM/CAE). Inżynieria odwrotna stanowi zwykle wyjściowy etap szybkiego prototypowania. Udostępnia ona metody generowania wirtualnych modeli 3D istniejących obiektów w wyniku ich pomiarów....
-
Influence of bush wear in water lubricated marine stern tube bearings with shaft misalignment
PublikacjaWater lubricated propeller shaft bearings are frequently employed on modern ships due to their advantages such as durability, simplicity and low price. Specific working conditions on ships cause shaft misalignment which often results in rapid wearing of bush and shaft. Shaft misalignment could be an effect of manufacturing or assembly faults but sometimes it appears due to hull or shaft deformation. The wearing process has influence...
-
PROPELLER INVESTIGATIONS BY MEANS OF NUMERICAL SIMULATION
PublikacjaThe analyses of hydroacoustics are of high interest at the moment due to strong impact of hydroacoustic phenomena on marine environment; the noises, generated e.g. by marine traffic, may be harmful for sea life. The analyses presented here are focused on one of main sources of noises generated by ships, i.e. cavitating propeller. The goal of the work is the assessment of the cavitation phenomenon, carried out with the standard...
-
Numerical and experimental propeller noise investigations
PublikacjaThe standard propeller has been investigated in model scale, using medium size cavitation tunnel. The hydroacoustic characteristics of propellers under different loading conditions have been investigated. Additionally the presented experimental results have been used for the verification of applied numerical approach. During both numerical and experimental analyses non-uniform inflow propeller’s conditions have been adapted. Good...
-
Numerical Simulations of Hydrodynamic Open-Water Characteristics of a Ship Propeller
PublikacjaThe paper presents the results of numerical simulations of ship propeller operation bearing the name of Propeller Open Water (POW) Tests. The object of tests was a sample ship propeller (PPTC1), the geometrical and kinematic data of which are available, along with the results of model tests, on the official page of the research centre involved in the measurements. The research aimed at verifying the correctness of results of numerical...
-
ASIC Design Example of Complex SoC with FPGA Prototyping
PublikacjaThe paper presents an example of the System on a Chip design, where the FPGA prototyping has been used. Two FPGA prototypes have been realized. The first FPGA prototype uses AVNET board containing Xilinx Virtex4 device accompanied by custom board with required devices. The second FPGA prototype has been built using the custom PCB with Xilinx Virtex-4 XC4VLX60 FPGA accompanied by all needed external components. The final system...
-
ASIC Design Example of Complex SoC with FPGA Prototyping
PublikacjaThe paper presents an example of the System on a Chip design, where the FPGA prototyping has been used. Two FPGA prototypes have been realized. The first FPGA prototype uses AVNET board containing Xilinx Virtex4 device accompanied by custom board with required devices. The second FPGA prototype has been built using the custom PCB with Xilinx Virtex-4 XC4VLX60 FPGA accompanied by all needed external components. The final system...
-
APPLICATION OF VORTEX FLOW MODEL IN PROPELLER-STATOR SYSTEM DESIGN AND ANALYSIS
PublikacjaThe paper covers basics of the vortex model used for propeller-stator systems. The outline of the design algorithm is given and the results of its application are shown. The designed propeller-stator system was the subject of model tests run at the CTO model basin and cavitation tunnel. Stator’s influence on the delivered power required by the propeller and its revolution rate has been examined by conducting self-propulsion...
-
Propeller-Like Chirality of Methyl-Tris (2,6-diisopropylphenoxy)Silylsulfide
PublikacjaTwo new methylsilylsulfides are synthesized. Propeller-like chirality is described for triaryloxysilanethiol and its methyl derivative. S-methylation of the silanethiol lowers the overall symmetry of the unit cell.
-
EXPERIMENTAL AND NUMERICAL VALIDATION OF THE IMPROVED VORTEX METHOD APPLIED TO CP745 MARINE PROPELLER MODEL
PublikacjaThe article presents a numerical analysis of the CP745 marine propeller model by means of the improved vortex method and CFD simulations. Both numerical approaches are validated experimentally by comparing with open water characteristics of the propeller. The introduced modification of the vortex method couples the lifting surface approach for the propeller blades and the boundary element method for the hub. What is more, a...
-
A method to assess transverse vibration energy of ship propeller shaft for diagnostic purposes
PublikacjaThe article discusses a key problem of ship propulsion system vibration diagnostics, which concerns assessing this part of mechanical energy transmitted from the main engine to the ship propeller which is dissipated due to propeller shaft vibration. A simplified calculation model is proposed which allows the total energy of the generated torsional vibration to be assessed from the shaft deflection amplitude measured at the mind-span...
-
Analysis of hull, propeller and engine interactions in regular waves by a combination of experiment and simulation
PublikacjaAnalysis of hull, propeller and engine interactions in regular waves by a combination of experiment and simulation
-
Critical review of propeller performance scaling methods based on model experiments and numerical calculations
PublikacjaThe article presents the results of experimental and theoretical investigation of propeller scale effects. The objective of this investigation is to test the adequacy of the methods currently used and to develop possible improvement of the methods.New approaches to the problem and new procedures to account for the propeller scale effects are suggested. The description of the underlying experimental and theoretical research is included.
-
Experimental and Computational Analysis of the Ship Propeller in Open Water Conditions for Inclined Flow
PublikacjaThe paper presents the results of computational analyses simulating the open water tests of ship propeller in inclined flow. The results of computations are compared with the results of corresponding experimental analyses carried out in the towing tank of Ship Design and Research Centre (CTO S.A.). The object of the research was the model propeller identified as CP469. The aim of the study was to validate the results of numerical...
-
Numerical Analysis of the Unsteady Propeller Performance in the Ship Wake Modified by Different Wake Improvement Devices
PublikacjaThe paper presents summary of numerical analysis of the unsteady propeller forces and induced pressure pulses generated by the selected real propeller of 7000 tons product tanker, operating in five different wakefields including four inflenced by the different wake improvement devices. The results of the analysis are partly compared with experimental data and univocal conclusions about the optimum wake improvement device are presented.
-
Blade Section Prpfile Array Lifting Surface Design Method for Marine Screw Propeller Blade
PublikacjaThe lifting surface model is widely used in screw propeller design and analysis applications. It serves as a reliable tool for determination of the propeller blade mean line and pitch distribution. The main idea of this application was to determine the blade shape that would satisfy the kinematic boundary condition on its surface with the prescribed bound circulation distribution over it. In this paper a simplified lifting surface...
-
Optimization of clamping stiffness during milling of high-dimensional structures with the use of techniques of experiment – aided virtual prototyping
PublikacjaThe subject of this paper is a method of searching for conditions of minimizing the vibration level of a tool-high dimensional flexible workpiece, at unchangeable technological parameters of the machining process. It depends on repeatable change of the values of the stiffness coefficients as soon as an optimal vibration state of the workpiece approaches. There are assessed the values of dominant ”peaks” in the frequency spectra...
-
User interface prototyping. Techniques, methods and tools
PublikacjaCurrently, for interactive applications their usability and ergonomics of the user interface (UI) are critical factors for achieving users' acceptance.
-
Experiment-aided virtual prototyping to minimize tool-workpiece vibration during boring of large-sized structures
PublikacjaThe paper presents the author's method of solving the problems of vi-bration suppression during boring of large-sized workpieces by means of an in-novative method of adjusting the rotational speed of the boring bar. It consists in selecting the spindle speed in accordance with the results of the cutting process simulation. The method includes identification of the model of the finite element method of the boring bar. The Root Mean...
-
The Possibilities of Improving the Fatigue Durabilityof the Ship Propeller Shaft by Burnishing Process
PublikacjaHeavily loaded structural elements operating in a corrosive environment are usuallyquickly destroyed. An example of such an element is a ship propeller operating in a seawaterenvironment. This research presents a fatigue resistance test performed on elements operating inseawater. Different processing parameters applied on the samples in particular were compared withthe specimens whose surface had been burnished differently and...