Filtry
wszystkich: 6298
-
Katalog
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: LOW TEMPERATURE CRACKING
-
Investigation of the 0.4C-35Cr-45Ni-Nb Alloy after Service in High-Temperature Steam and Hydrocarbons Environment
PublikacjaThe paper presents the results of investigation of the 0.4C-35Cr-45Ni-Nb alloy, which operated in the cracked hydrocarbon feeds and dilution steam at 1125 C. The material originated from the pyrolytic furnace coil tubes, of which internal walls were in contact with the aforementioned medium, whereas the external walls were in contact with the flue gases. The examination included metallographic and mechanical tests on the material...
-
Accurate Lightweight Calibration Methods for Mobile Low-Cost Particulate Matter Sensors
PublikacjaMonitoring air pollution is a critical step towards improving public health, particularly when it comes to identifying the primary air pollutants that can have an impact on human health. Among these pollutants, particulate matter (PM) with a diameter of up to 2.5 μ m (or PM2.5) is of particular concern, making it important to continuously and accurately monitor pollution related to PM. The emergence of mobile low-cost PM sensors...
-
Method of reconstructing two-dimensional velocity fields on the basis of temperature field values measured with a thermal imaging camera
PublikacjaThis paper describes a novel numerical reconstruction procedure (NRP) of the velocity field during natural convective heat transfer from a two-sided, isothermal, heated vertical plate based only on the known temperature field obtained, e.g. with a thermal imaging camera. It has been demonstrated that with a knowledge of temperature distributions, the NRP enables the reconstruction of velocity fields by solving the Navier-Stokes...
-
Polyurethane glycolysate from industrial waste recycling to develop low dielectric constant, thermally stable materials suitable for the electronics
PublikacjaWe are utilizing a new method to improve the dielectric properties of a conventional polymer using a recycled polymer product. The polyurethane foams are recycled by glycolysis process and the derived material was applied to improve the dielectric properties of the brittle DGEBA epoxy resin. Two main parameters that determine the applicability of the material as a dielectric (the dielectric constant and dielectric loss), were studied...
-
Low-energy positron scattering from gas-phase uracil
PublikacjaQuantum scattering calculations are presented for the interaction of low energy positrons with the uracil molecule, an important component of biological systems. The rotational elastic and inelastic cross sections and vibrational inelastic cross sections are reported and compared with existing experiments, indicating a general trend of the cross sections different from the experimental findings and in line with what should be expected...
-
Low-Cost EM-Simulation-Driven Multi-Objective Optimization of Antennas
PublikacjaA surrogate-based method for efficient multi-objective antenna optimization is presented. Our technique exploits response surface approximation (RSA) model constructed from sampled low-fidelity antenna model (here, obtained through coarse-discretization EM simulation). The RSA model enables fast determination of the best available trade-offs between conflicting design goals. A low-cost RSA model construction is possible through...
-
Comparative electrochemical analysis of the passive layer cracking process on aluminum alloys performed by means of DC and AC techniques
PublikacjaZbadano proces pękania warstwy pasywnej na stopach aluminium AA1050, AA5052, AA5056, oraz AA7005 w warunkach zmiennych naprężeń rozciągających i polaryzacji anodowej z wykorzystaniem techniki stałoprądowej, DEIS oraz emisji akustycznej (AE), jako metody porównawczej. Przeprowadzone badania pokazały przewagę techniki DEIS oraz emisji akustycznej nad klasyczną techniką stałoprądową. Wyznaczono dokładny moment pęknięcia warstwy pasywnej...
-
Korozja naprężeniowa stali 14hnmbcu w środowisku wody morskiej.Stress corrosion cracking of 14hnmbcu steel in sea-water.
PublikacjaW pracy przedstawiono zagadnienia niszczenia środowiskowego stali o wysokiej wytrzymałości na konstrukcje morskie. Podatność stali 14HNMBCu i jej złącza spawanego na naprężeniowe pękanie korozyjne badano w oparciu o próbę powolnego rozciągania. Próby wykonano w środowisku powietrza oraz wody morskiej przy polaryzacji katodowej.
-
Stress corrosion cracking of Al-Zn-Mg weldments.Korozja naprężeniowa złączy spawanych stopów Al-Zn-Mg.
PublikacjaPraca zawiera wyniki badań odporności korozyjnej złączy spawanych Al-Zn-Mg. Zbadano wpływ składu chemicznego stopu oraz spoiwa na odporność na korozje naprężeniową w warunkach statycznych naprężeń rozciągających.
-
Influence of retrogression and reaging on microstructure, mechanical properties and susceptibility to stress corrosion cracking of an Al-Zn-Mg alloy.
PublikacjaPrzedmiotem badań był stop AlZn5Mg1 poddany nawrotowi i starzeniu w różnej temperaturze i przez różny czas. Badano podatność na korozję naprężeniową przy stałej prędkości rozciągania 10-6 s-1. Obróbka cieplna, która polepsała własności, pogarszała odporność na korozję naprężeniową. Efekty te przypisano zmianiom wielkości i rozkładu wydzieleń.
-
Electrochemical analysis of the passive layer cracking process on A95052 aluminium alloy performed by means of DC and AC techniques
PublikacjaPraca dotyczy porównania zastosowania technik stało- i zmiennoprądowych do badania pękania warstwy pasywnej na różnych stopach aluminum podczas testów rozciągania mechanicznego w warunkach polaryzacji anodowej.
-
Multimodal analysis of traction forces and the temperature dynamics of living cells with a diamond-embedded substrate
PublikacjaCells and tissues are constantly exposed to chemical and physical signals that regulate physiological and pathological processes. This study explores the integration of two biophysical methods: traction force microscopy (TFM) and optically detected magnetic resonance (ODMR) to concurrently assess cellular traction forces and the local relative temperature. We present a novel elastic substrate with embedded nitrogen-vacancy microdiamonds...
-
Low-Power WSN System for Honey Bee Monitoring
PublikacjaThe paper presents a universal low-power system for biosensory data acquisition in scope of bees monitoring. We describe the architecture of the system, energy-saving components as well as we discuss the selection of used sensors. The work focuses on energy optimization in a scope of wireless communication. A custom protocol was implemented, which is the basis for presented energy-efficient devices. Data exchange process during...
-
Distribution of Temperature in Multicomponent Multilayered Composites
Publikacja -
Temperature-dependent photoluminescence of polyazomethine films
Publikacja -
Optimal boiling temperature for ORC installation
PublikacjaW pracy przedstawiono oryinalne kryterium wyznaczania optymalnej temperatury odparowania czynnika w obiegu ORC w postaci równań analitycznych. Pokazano przykład obliczeniowy na bazie R134a, wody i etanolu.
-
Impact of high temperature drying process on beech wood containing tension wood
PublikacjaThe technology of high temperature drying has a great inuence on dimensional and selected physical changes in tension wood. Article is focused on the measurement properties such as moisture content, color changes and longitudinal warping. The quality of beech wood is determined based on structure and properties of wood, frequency of defects in wood material. The tension wood is considered as an important wood defect causing negative...
-
The effect of high pressure and subzero temperature on gelation of washed cod and salmon meat
PublikacjaThe objective of the present work is to examine the infl uence of pressure up to 193 MPa at subzero temperature (without freezing of water) on myofi brillar proteins of salmon and cod meat and on the properties of gels obtained from washed mince of these fi sh. The solubility of proteins from myofi brils of cod and salmon meat suspended in 100 mM KCl solution increased aft er treating the samples with pressure above 60 MPa. The...
-
Exchange of radiation in high temperature air combustion furnaces by application of the transfer configuration factors
PublikacjaW artykule przedstawiono metodę obliczeń pasmowej radiacyjnej wymiany ciepła w układzie otwartym z gazem iztermicznym za pomocą uogólnionych współczynników konfiguracji. Metoda może być użyta do obliczeń wymiany ciepła w piecach z technologią High Temperature Air Combustion gdzie występuje prawie jednorodna temperatura. Podano przykład obliczeniowy.
-
Achieving Efficient and Stable Deammonification at Low Temperatures—Experimental and Modeling Studies
PublikacjaThe short-term effects of temperature on deammonification sludge were evaluated in a laboratory-scale sequencing batch reactor (SBR). Mathematical modeling was used for further evaluations of different intermittent aeration strategies for achieving high and stable deammonification performance at decreasing temperatures. As for the biomass cultivated at high temperatures (e.g., 30 C), a higher temperature dependency (the adjusted...
-
Design of Intelligent Low-Voltage Load Switch for Remote Control System in Smart Grid
PublikacjaCurrent low-voltage load switches do not support remote disconnect/connect and real-time monitoring of a disconnect/connect state. Addressing to these issues, this paper presents a low-voltage load switch for a smart remote control system, which uses a one-chip microcontroller board and a DC step motor drive mechanism and provides the feedback on the switch status also. Arrears disconnect and full-pay connect control is implemented...
-
Determination of Thermophysical Parameters Involved in The Numerical Model to Predict the Temperature Field of Cast-In-Place Concrete Bridge Deck
PublikacjaThe paper dealswith a concept of a practical computationmethod to simulate the temperature distribution in an extradosed bridge deck. The main goal of the study is to develop a feasible model of hardening of concrete consistent with in-situ measurement capabilities. The presented investigations include laboratory tests of high performance concrete, measurements of temperature evolution in the bridge deck and above all, numerical...
-
Study of pH and temperature effect on lipophilicity of catechol-containing antioxidants by reversed phase liquid chromatography
PublikacjaLipophilicity of selected antioxidant phytochemicals, including flavonoids, phenolic acids and xanthonoids, was determined by reversed phase high performance liquid chromatography with UV detection (RP-HPLC-UV). The analyses run at different temperature and pH conditions in isocratic mode suggested that lipophilicity as distribution coefficient (logD) between aqueous and organic phase decreases with increasing temperature. For...
-
Nickel-nanodiamond coatings electrodeposited from tartrate electrolyte at ambient temperature
PublikacjaIn this study, nanocrystalline Ni and Ni-diamond coatings were obtained by electrodeposition from tartrate electrolyte at ambient temperature aiming at improving corrosion and wear properties of the material. The created surfaces were investigated with regard to microhardness, adhesion, wear- and corrosion-resistance. The various methods such as atomic force microscopy, scanning electron microscopy, electrochemical impedance spectroscopy...
-
S-Shaped Suppression of the Superconducting Transition Temperature in Cu-Intercalated NbSe2
Publikacja2H-NbSe2 is the prototype and most frequently studied of the well-known transition metal dichalcogenide (TMDC) superconductors. As 2H-NbSe2 is widely acknowledged as a conventional superconductor, its transition temperature to the superconducting state (Tc) is 7.3 K, a Tc that is substantially higher than those seen for the majority of TMDCs, where Tc values between 2 and 4 K are the norm. Here we report the intercalation of Cu...
-
Low cost set-up for supercapacitors parameters evaluation
PublikacjaSupercapacitors are capable to store relatively high amount of energy comparing to its mass. Growing number of these devices applications requires development of new testing methods. Standard methods of evaluation of supercapacitor parameters, as cycling voltammetry, CV, galvanostatic cycling with potential limitation, GCPL, impedance measurements, require equipment of high cost...
-
Exhaust gas temperature measurements in diagnostics of turbocharged marine internal combustion engines. Part I. Standard measurements.
PublikacjaThe article discusses the problem of diagnostic informativeness of exhaust gas temperature measurements in turbocharged marine internal combustion engines. Theoretical principles of the process of exhaust gas flow in turbocharger inlet channels are analysed in its dynamic and energetic aspects. Diagnostic parameters are defined which enable to formulate general evaluation of technical condition of the engine based on standard...
-
Temperature Measurements at Tyre Tread Rubber on Sandpaper Oscillatory Sliding Contacts Using Acicular Grindable Thermocouples
PublikacjaThe tribological performance of tyre–road contacts depends crucially on the contact temperature. This study investigates the reliability and accuracy of acicular grindable thermocouples possessing an original needle-shaped wearable part as applied to measuring temperature at the oscillatory sliding contact between a rubber tyre tread sample and a sandpaper. A linear oscillatory tribometer is used to imitate the sliding phase of...
-
A Computational Analysis of the Aerodynamic and Aeromechanical Behavior of a Thermo-Well for Steam Temperature Measurement in a Steam Turbine
PublikacjaThe goal of the paper is twofold: firstly, it presents computational fluid dynamics analysis for finding maximum unsteady flow forces (and their frequencies) acting on a thermo-well for measuring steam temperature in a steam turbine control stage and secondly, it presents computational solid dynamics analysis of possibility of entry into resonance of the thermowell structure. There have been analyzed two cases of flow with changing...
-
Energy consumption estimation of low-power devices using an integrating coulombmeter
PublikacjaThe main problem in designing devices powered with Energy Harvesting is an estimation of energy demand of low-power devices as well as quantity of energy provided by the selected energy transducer in the assumed work conditions. Due to the work characteristic of each block of the device and properties of the measured signal, measurement is not trivial. The paper presents the proposal of the micro-charge measurement device based...
-
Dutch Crossing : a Journal of Low Countries Studies
Czasopisma -
Evaluation of Temperature Influence on Electrochemical Processes Occurring in a Lithium-Ion Supercapacitor with the Use of Dynamic Electrochemical Impedance Spectroscopy
PublikacjaIn order to obtain the full impedance characteristics of a lithium-ion capacitor as a function of temperature, the authors proposed the use of dynamic electrochemical impedance spectroscopy. Impedance tests were carried out under wide range of dynamic temperature changes for lithium-ion supercapacitors. Significant differences in electrochemical processes were observed as a result of working temperature. Moreover, the quality of...
-
CaO-based high temperature CO2 sorbents – Literature review
PublikacjaThe use of CaO-based adsorbents has a high potential to capture CO2 from various systems due to its high reactivity with CO2, high capacity, and low cost of naturally derived CaO. The application of CaO-based sorbents to remove carbon dioxide is based on a reversible reaction between CaO and CO2. However, multiple carbonation/calcination cycles lead to a rapid reduction in the sorption capacity of natural CaO, and therefore efforts...
-
Capillary Electrophoresis in Determination of Low Molecular Mass Organic Acids
PublikacjaThis paper presents overviews the capabilities of capillary electrophoretic techniques to determine low molecular mass organic acids in a variety of aqueous, gas and solid samples. It mainly focuses on short - chain carboxylic acids containing one or more carboxylic groups and possibly some other functional groups (hydroxyl, keto-, amino- etc.). Finally the procedures applied to the determine the acids in different matrices are...
-
Pavement ageing influence on tyre/road noise
PublikacjaRoad surface should be constructed in a way that ensures safe and comfortable traffic conditions, not only when it is newly paved but also during its entire lifetime. An important factor in the asphalt mixture design process is also the expected pavement durability and stability of pavement properties over time. In many countries, road surface starts to play a significant role in traffic noise reduction actions. Selecting a particular...
-
Biophotonic low-coherence sensors with boron-doped diamond thin layer
PublikacjaLow-coherence sensors using Fabry-Perot interferometers are finding new applications in biophotonic sensing, especially due to the rapid technological advances in the development of new materials. In this paper we discuss the possibility of using boron-doped nanodiamond layers to protect mirror in a Fabry-Perot interferometer. A low-coherence sensor using Fabry-Perot interferometer with a boron-doped nanodiamond (B-NCD) thin protective...
-
Noise measurements on low noise pavements - problems with inhomogeneity of wearing course
PublikacjaDuring the last several years, when performing numerous CPX noise measurements on low noise pavements,significant inhomogeneity of the wearing course was observed in numerous cases. Similar problems were almost not existing regarding to the dense pavements.In general three main reasons of inhomogeneity can be defined. The first one are imperfections in technology of production of a asphalt mix or/and errors made already during...
-
Low and high energy explosive materials used in shale gas recovery
PublikacjaNowadays the explosives are widely used in many areas of life, including industry and mining. A wide range of explosive materials is used in the petroleum industry - from low to high explosives. Recently, as the unconventional oil and gas production became possible, explosives are also found to be used in perforators during the pre-completion stage of the fracturing process. This paper presents literature on theoretical and practical...
-
DIAGNOSTIC INFORMATION ANALYSIS OF QUICKLY CHANGING TEMPERATURE OF EXHAUST GAS FROM MARINE DIESEL ENGINE PART I SINGLE FACTOR ANALYSIS
PublikacjaIn this paper, attention was paid to the problem of low controllability of marine medium- and high-speed engines during operation, which significantly limits the parametric diagnosis. The measurement of quickly changing temperature of engine exhaust gas was proposed, the courses of which can be a source of diagnostic information. The F statistic of the Fisher-Snedecor distribution was chosen as a statistical tool. Laboratory tests...
-
QUASI-DISTRIBUTED NETWORK OF LOW-COHERENCE FIBER-OPTIC FABRY-PÉROT SENSORS WITH CAVITY LENGTH-BASED ADDRESSING
PublikacjaDistributed measurement often relies on sensor networks. In this paper, we present the construction of low coherent fiber-optic Fabry-Pérot sensors connected into a quasi-distributed network. We discuss the mechanism of spectrum modulation in this type of sensor and the constraints of assembly of such sensors in the network. Particular attention was paid to separate the signals from individual sensors, which can be achieved by...
-
Low energy electron attachment to platinum(II) bromide (PtBr2)
PublikacjatDissociative electron attachment to PtBr2in the gas phase was studied in the low electron energy rangefrom zero up to 10 eV with an energy resolution of 150 meV. The experiments were carried out using ahemispherical electron monochromator coupled with a quadrupole mass spectrometer and pulse count-ing acquisition system. The only anion observed was Br−. This ion is formed at three resonance electronenergies: 0.4 eV, 1.2 eV and...
-
Automatic Correction of Non-Anechoic Antenna Measurements using Low-Pass Filters
PublikacjaPrototype measurements belong to key steps in the development of antenna structures. They are normally performed in expensive facilities, such as anechoic chambers (ACs). Alternatively, antenna performance can be extracted (at a low cost) in non-anechoic conditions upon appropriate post-processing. Unfortunately, existing correction algorithms are difficult to set up and prone to failure, which limits their practical usefulness....
-
Fabrication, Microstructure and High Temperature Corrosion Resistance of Porous Alloys for Solid Oxide Fuel Cells
PublikacjaPorous alloys find use in modern Solid Oxide Fuel Cells as the supporting structures. As they are exposed to high temperatures (> 500°C) an oxide scale forms on their surface due to high temperature corrosion phenomena. Since the ratio between the surface area and volume is much higher than for planar samples, formation of the oxide can lead to a breakaway oxidation after relatively short times. Therefore corrosion properties of...
-
Temperature measurement using NIR camera with automatic adjustment of integration time for monitoring high-temperature industrial processes
Publikacja -
Electron ionization and low energy electron attachment to molecules of biological interest
PublikacjaEthylenediaminetetraacetic acid (EDTA) and 2-amino-2-(hydroxymethyl)-1,3-propanediol (TRIS) were investigated by electron impact ionization and low energy electron attachment. Both compounds are components of biological buffers and often are used as DNA stabilizers in irradiation studies. hus it is of a great importance to understand their potential interactions with radiation. Our results revealed that at least one of them, EDTA, may...
-
Electron ionization and low energy electron attachment to molecules of biological interest
PublikacjaEthylenediaminetetraacetic acid (EDTA) and 2-amino-2-(hydroxymethyl)-1,3-propanediol (TRIS) were investigated by electron impact ionization and low energy electron attachment. Both compounds are components of biological buffers and often are used as DNA stabilizers in irradiation studies. hus it is of a great importance to understand their potential interactions with radiation. Our results revealed that at least one of them, EDTA, may...
-
The Influence of Drying Temperature on Color Change of Hornbeam and Maple Wood Used as Surface and Inner Layers of Wood Composites
PublikacjaThe thermal treatment of wood changes its structure due to the degradation of wood polymers (cellulose, hemicellulose and lignin), so the physical properties of wood are either improved or degraded. Color changes apply not only to natural wood, but also to such wood composites for which some amount of glue is used in their construction (e.g., plywood, blockboard or laminboard). This article is focused on the analysis of hornbeam...
-
Study of Soil Temperature and Moisture Changes in a Physical Model of an Underground Cable Line
PublikacjaThe ampacity of power cables is highly dependent on the thermal resistivity of the soil in which they are laid. The lower it is, the higher this ampacity. The thermal resistivity of the soil decreases as its moisture increases. Therefore, it is preferable that the soil around the cables has high moisture. Unfortunately, the heat generated in heavily loaded cables causes the migration of moisture from the surrounding soil, which...
-
Dynamic mass measurement in checkweighers using a discrete time-variant low-pass filter
PublikacjaConveyor belt type checkweighers are complex mechanical systems consisting of a weighing sensor (strain gauge load cell, electrodynamically compensated load cell), packages (of different shapes, made of different materials) and a transport system (motors, gears, rollers). Disturbances generated by the vibrating parts of such a system are reflected in the signal power spectra in a form of strong spectral peaks, located usually in...
-
Measurement of complex refractive index of human blood by low-coherence interferometry
PublikacjaIn this article, the usefulness of the optical technique for measurements of blood complex refractive index has been examined. Measurement of optical properties of human blood is difficult to perform because of its nonuniform nature. However, results of my investigation have shown the usefulness of low-coherencei nterferometry for measurement complex refractive index of human blood. Furthermore, mathematical analysis of spectrum...