wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: CURVED CARBON NANOTUBES
-
Wyznaczanie współczynników dyfuzji tlenku węgla (IV) przez membrany wysycone cieczą jonową = Determination of carbon dioxide diffusion coefficients in supported ionic liquids membranes
PublikacjaWykazano możliwość zastosowania imidazoliowych cieczy jonowych osadzonych na nośnikach polimerowych SILM (supported ionic liquids membranes) do absorpcji CO2. W badaniach wykorzystano sole imidazoliowe posiadające w strukturze aniony fluoroalkilowe typu [Tf2N] i [TfO], które selektywnie separują tlenek węgla (IV). Wyznaczono współczynniki dyfuzji CO2 przez poszczególne SILM na podstawie ilości dyfundującego CO2 przez powierzchnię...
-
Facile synthesis of accordion-like porous carbon from waste PET bottles-based MIL-53(Al) and its application for high-performance Zn-ion capacitor
Publikacja -
Corrosion behaviour of low carbon steel in artificial seawater using TP, LP, EIS, Harmonic Analysis (HA) and new method Dynamic Electrochemical Impedance Spectroscopy (DEIS)
PublikacjaZe względu na istotną rolę technik elektrochemicznych w badaniach procesów korozyjnych są one szeroko stosowane w monitorowaniu korozji. Celem niniejszej pracy jest zgromadzenie rezultatów wyników doświadczalnych uzyskanych różnymi technikami i znalezienie korelacji między nimi. Własności korozyjne stali stopowej (AISI 1026) w sztucznej wodzie morskiej zostały zbadane z wykorzystaniem ekstrapolacji tafelowskiej (TP), polaryzacji...
-
Mechanics of Micro- and Nano-Size Materials and Structures
PublikacjaNanotechnology knowledge is always looking to expand its boundaries to achieve the mostsignificant benefit to human life and meet the growing needs of today. In this case, we can refer tomicro- and nanosensors in micro/nano-electromechanical systems (MEMS/NEMS). These electricaldevices can detect minimal physical stimuli up to one nanometer in size. Today, micro/nano-sensordevices are widely used in the...
-
Wideband crossover structure with double ring resonators
PublikacjaThe structure of a four-port microstrip crossover is presented. The device is composed of two ring resonators, one circular and one built from meander lines, connected by four straight lines. The equivalent circuit model of the crossover is derived. The structure is designed on thin and flexible substrate to allow it to bend. The possibility of applying the device on curved surfaces is tested experimentally.
-
Recent developments and future trends in solid phase microextraction techniques towards green analytical chemistry
PublikacjaSolid phase microextraction find increasing applications in the sample preparation step before chromatographic determination of analytes in samples with a complex composition. These techniques allow for integrating several operations, such as sample collection, extraction, analyte enrichment above the detection limit of a given measuring instrument and the isolation of analytes from sample matrix. In this work the information about...
-
Synthetic strategies in construction of organic macromolecular carrier–drug conjugates
PublikacjaMany metabolic inhibitors, considered potential antimicrobial or anticancer drug candidates, exhibit verylimited ability to cross the biological membranes of target cells. The restricted cellular penetration ofthose molecules is often due to their highhydrophilicity. One of the possible solutions to this problem is aconjugation of an inhibitor with a molecular organic nanocarrier. The conjugate thus formed should beable to penetrate...
-
Dispersive Micro‐Solid Phase Extraction of Selected Metals in Water and Food Samples Followed by ICP‐OES Analysis: Method Development, Analysis of Real Samples and Greenness Evaluation
PublikacjaMultiwalled carbon nanotubes (MWCNTs) are well-known adsorbents because of their high surface area, layered and hollow architecture, hydrophobicity, and multiple and easily accessible adsorption sites. In this study, MWCNTs were used for dispersive micro-solid-phase extraction of various metal chelates in environmental and food samples. Different parameters such as concentration of the chelating reagent, the sorbent dosage, the...
-
Mechanical Behavior of Bi-Layer and Dispersion Coatings Composed of Several Nanostructures on Ti Substrate
PublikacjaThree coatings suitable for biomedical applications, including the dispersion coating composed of multi-wall carbon nanotubes (MWCNTs), MWCNTs/TiO2 bi-layer coating, and MWCNTs-Cu dispersion coating, were fabricated by electrophoretic deposition (EPD) on Ti Grade II substrate. Optical microscopy, scanning electron microscopy, energy-dispersive X-ray spectroscopy, and nanoindentation were applied to study topography, chemical, and...
-
Antimicrobial molecular nanocarrier–drug conjugates
PublikacjaMany antimicrobial drugs are poorly active against pathogenic microbes causing intracellular infections, such as Mycobacterium tuberculosis or Plasmodium falciparum. On the other hand, several known antimicrobial agents are not effective enough because of their limited cellular penetration. A common feature of both challenges is the inability of an active agent to cross the biological membrane(s). One of the possible approaches...
-
Cure kinetics of epoxy/MWCNTs nanocomposites: Isothermal calorimetric and rheological analyses
PublikacjaA combinatorial route has been applied in cure kinetics study of epoxy nanocomposites containing multi-walled carbon nanotubes (MWCNTs) based on differential scanning calorimetry and rheokinetic analyses under isothermal conditions. Pristine and amine-modified MWCNTs bearing primary and secondary amines were used at very low concentrations (0.1 and 0.3 wt.% based on epoxy weight). Model-free and model-fitting methods were applied...
-
Simultaneous determination of droxidopa and carbidopa by carbon paste electrode functionalized with NiFe2O4 nanoparticle and 2-(4-ferrocenyl-[1,2,3]triazol-1-yl)-1-(naphthalen-2-yl) ethanone
Publikacja -
Biogeochemistry of three different shallow gas systems in continental shelf sediments of the South-Eastern Baltic Sea (Gulf of Gdańsk): Carbon cycling, origin of methane and microbial community composition
Publikacja -
Na3PO4 assistant dispersion of nano-CaCO3 template to enhance electrochemical interface: N/O/P co-doped porous carbon hybrids towards high-performance flexible supercapacitors
Publikacja -
Effect of irradiation intensity and initial pollutant concentration on gas phase photocatalytic activity of TiO2 nanotube arrays
PublikacjaWell-organized TiO2 nanotube arrays were fabricated via one-step anodization process. The as-prepared TiO2 nanotubes were characterized by X-ray powder diffractometry (XRD), X-ray photoelectron spectroscopy (XPS), diffuse reflectance spectroscopy (DRS) and scanning electron microscopy (SEM). Photocatalytic activity of obtained photocatalyst was studied in reaction of toluene degradation in the gas phase using low powered and low...
-
Micro-cracking pattern recognition of hybrid CNTs/GNPs cement pastes under three-point bending loading using acoustic emission technique
PublikacjaThe generation of microcracks has an important influence on the behaviour of concrete structures. In this study, the acoustic emission (AE) technique was used to investigate the fracture phenomena and micro-cracking behavior of hybrid carbon nanotubes (CNTs, the 1-D allotrope of carbon atoms) and graphene nanoplatelets (GNPs, 2D monolayer of sp2-hybridized carbon atoms), cement composites under three-point bending loading. In...
-
Corrigendum to “The influence of α,ω-diols and SiO2 particles on CO2 absorption and NH3 escaping during carbon dioxide capture in ammonia solutions” [J. CO2 Util. 80 (2024) 102698]
Publikacjanie dotyczy
-
On the crack front curvature in bonded joints
PublikacjaStandard tests of adhesively bonded specimens are likely to produce heterogeneous stress distribution along the crack front and its vicinity. High separation rate mode I dominated fracture test is performed.Observation of post mortem fractured surfaces with an optical microscope reveals characteristic features of mixed mode I/III fracture near the sides of the specimen but not in the middle. At first, finite elements calculations...
-
Recent Advances in Polymer Nanocomposites: Unveiling the Frontier of Shape Memory and Self-Healing Properties—A Comprehensive Review
PublikacjaShape memory and self-healing polymer nanocomposites have attracted considerable attention due to their modifiable properties and promising applications. The incorporation of nanomaterials (polypyrrole, carboxyl methyl cellulose, carbon nanotubes, titania nanotubes, graphene, graphene oxide, mesoporous silica) into these polymers has significantly enhanced their performance, opening up new avenues for diverse applications. The...
-
Ti-Fe2O3/In2O3 as photoactive material: The role of the substrate in photoelectrochemical water oxidation
PublikacjaThe layers of Ti-Fe2O3/In2O3 were prepared on the different substrates using hydrothermal method: Ti/TiO2 nanotubes, Ti foil, FTO and FTO/TiO2. Materials were characterized using scanning electron microscopy, XRD, Raman, UV-Vis, and X-ray photoelectron spectroscopy and tested as photoanodes for water oxidation under illumination. The formation of heterojunction on the TiO2 nanotubes increases photocurrent of water oxidation at...
-
Mechanical Properties of Polyester Coated Fabric Subjected to Biaxial Loading
PublikacjaThe paper is focused on the comparison between uniaxial and biaxial laboratory test results for polyester coated fabric. A short literature review concerning coated woven fabrics with emphasis on biaxial tensile tests is presented. A description of the polyester-coated fabric under biaxial test by means of constitutive models and material parameter values is proposed. To establish the right values of the ultimate tensile strength,...
-
Carbonaceous catalysts from orange pulp for limonene oxidation
Publikacja -
Cure Index demonstrates curing of epoxy composites containing silica nanoparticles of variable morphology and porosity
PublikacjaAn image was taken by Cure Index on curability of epoxy with silica nanoparticles having variable morphology and porosity. Three kinds of silica nanoparticles with non-porous curved-rod, non-porous spherical, and mesoporous spherical microstructures were synthesized and characterized by Fourier-transform infrared spectroscopy, scanning electron microscopy (SEM) and Brunauer–Emmett–Teller analyses. Epoxy nanocomposites containing...
-
Self-organized multilayered graphene-boron doped diamond hybrid nanowalls for high performance electron emission devices
PublikacjaCarbon nanomaterials like nanotubes, nanoflakes/nanowalls and graphene have been used as electron sources due to their superior field electron emission (FEE) characteristics. Nevertheless, these materials show poor stability and a short lifetime, preventing them from being used in practical device applications. The intention of this study was to find an innovative nanomaterial, possessing both high robustness and reliable FEE behavior....
-
New Trends in Sample Preparation Techniques for the Analysis of the Residues of Pharmaceuticals in Environmental Samples
PublikacjaPharmaceutical residues in the environment is a field of special interest due to the adverse effects to either human health or aquatic and soil environment. Pharmaceuticals have been already detected in underground, surface and wastewaters, soils, manure and sediments. The growing awareness of environmental pollution arising from human activity forces the need for their comprehensive determination. Environmental samples are complex...
-
Cure kinetics of epoxy/MWCNTs nanocomposites: Nonisothermal calorimetric and rheokinetic techniques
PublikacjaNonisothermal calorimetric and isothermal rheokinetic analyses were used to study cure kinetics of epoxy/anhydride systems containing very low concentration of pristine and amine-functionalized multiwalled carbon nanotubes (MWCNTs). Isoconversional methods were applied in calorimetric modeling of cure kinetics. Eα vs. α dependency and autocatalytic nature of curing were identified for both types of nanocomposites by isoconversional...
-
Wzbudzone siły wewnętrzne : skutki upr0szczonego modelowania zakrzywionej estakady sprężonej
Publikacjathe paper presents problems, which were encountered during the construction of a southern road bypass of city gdansk. after prestressing and removing formwork, the contractor spotted, that some of outer bearings are detached. performed analysis showed that, this situation was caused by the usage of a simplified, straight beam model during design phase. the paper shows the influence of a curved in plane prestressed system on internal...
-
Fabrication of Durable Ordered Ta2O5 Nanotube Arrays Decorated with Bi2S3 Quantum Dots
PublikacjaOne of the most important challenges in the fabrication of ordered tantalum pentaoxide (Ta2O5) nanotube arrays (NTs) via the electrochemical method is the formation of nanotubes that adhere well to the Ta substrate. In this paper, we propose a new protocol that allows tight-fitting Ta2O5 nanotubes to be obtained through the anodic oxidation of tantalum foil. Moreover, to enhance their activity in the photocatalytic reaction, in...
-
FLAME ATOMIC ABSORPTION SPECTROMETRIC DETERMINATION OF TRACE AMOUNTS OF SILVER IN RADIOLOGICAL WASTE SAMPLES AFTER SOLID PHASE EXTRACTION USING MULTI-WALLED CARBON NANO-TUBES MODIFIED BY SODIUM DODECYL SULFATE
Publikacja -
High Speed Milling vibration surveillance with optimal spindle speed based on optimal speeds map
PublikacjaThe paper presents the method of the surveillance of the self-excited chatter vibration. At first, the workpiece modal parameters are estimated based on experimental data which leads to verification of computational model. Then, for selected surface points optimal spindle speeds are calculated. By considering sufficient amount of points it is possible to build a map of optimal spindle speeds. Experimental results show that this...
-
Application of mesh deformation for modeling of conformal RF components with 3D FEM
PublikacjaIn this paper, a method of analysis of conformal RF components has been proposed. In this approach, modeling of a curved structure is based on mesh deformation of planar objects rather than the construction of conformal geometry at CSG level. Since the model is represented as a 3D mesh, the deformation only requires the calculation of nodes position in the bent structure. The results of the proposed algorithm have been validated...
-
Scaling Up the Process of Titanium Dioxide Nanotube Synthesis and Its Effect on Photoelectrochemical Properties
PublikacjaIn this work, for the first time, the influence of scaling up the process of titanium dioxide nanotube (TiO2NT) synthesis on the photoelectrochemical properties of TiO2 nanotubes is presented. Titanium dioxide nanotubes were obtained on substrates of various sizes: 2 × 2, 4 × 4, 5 × 5, 6 × 6, and 8 × 8 cm2. The electrode material was characterized using scanning electron microscopy as well as Raman and UV–vis spectroscopy in order...
-
Analytical design method for widening the intertrack space
PublikacjaThe paper involved the issue of arching of the railway turnouts. This is an issue which is given relatively less attention to scientific and research activities. Reference has been made to the book by Wladyslaw Rzepka, under the title „Curved turnouts in plan and profile”, which has been used in Poland for more than 50 years as the main source of information relating to the turnouts on the curve. The book is a compilation of elaborations...
-
Arching of railway turnouts by analytical design method
PublikacjaThe paper involved the issue of arching of the railway turnouts. This is an issue which is given relatively less attention to scientific and research activities. Reference has been made to the book by Wladyslaw Rzepka, under the title „Curved turnouts in plan and profile”, which has been used in Poland for more than 50 years as the main source of information relating to the turnouts on the curve. The book is a compilation of elaborations...
-
Mechanical Behavior of Bi-Layer and Dispersion Coatings Composed of Several Nanostructures on Ti13Nb13Zr Alloy
PublikacjaTitanium implants are commonly used because of several advantages, but their surface modification is necessary to enhance bioactivity. Recently, their surface coatings were developed to induce local antibacterial properties. The aim of this research was to investigate and compare me-chanical properties of three coatings: multi-wall carbon nanotubes (MWCNTs), bi-layer composed of an inner MWCNTs layer and an outer TiO2 layer, and...
-
The role and importance of total organic carbon (TOC) in production chain of KGHM Polska Miedż S.A. = Rola i znaczenie węgla organicznego w ciągu produkcyjnym realizowanym w KGHM Polska Miedź S.A.
PublikacjaWęgiel organiczny ma szczególne znaczenie w procesach realizowanych w ciągu technologicznym KGHM Polska Miedź S.A. Obecność węgla organicznego i złożoność problemów z nim związanych wynika głównie z jego występowania we wszystkich fazach tworzenia się złoża, a obecnie ma znaczący wpływ zarówno na przebieg procesu wzbogacania, jakość koncentratu, jak również na procesy ogniowe w technologii pieca zawiesinowego. Jednocześnie forma...
-
Oznaczanie tlenu – od metody Winklera do czujników enzymatycznych (Determination of oxygen – from Winkler Method to enzymatic sensor)
PublikacjaMonitoring of dioxygen levels is of utmost importance from the view-point of life processes, medical diagnostics, nutrition and chemical industries. In all these measurements both low and high levels of this element are important. The common methods for the determination of dioxygen are the Winkler method, Clark electrode and pulsoxymeters. A new, already strong field of research can be now recognized – the development of miniaturized...
-
Elastoplastic nonlinear FEM analysis of FGM shells of Cosserat type
PublikacjaThe paper is a continuation of [1] where the formulation of the elastic constitutive law for functionally graded materials (FGM) on the grounds of nonlinear 6-parameter shell theory with the 6th parameter (the drilling degree of freedom) was presented. Here the formulation is extended to the elasto-plastic range. The material law is based on Cosserat plasticity and employs the well-known Tamura-Tomota-Ozawa (TTO) [2] mixture...
-
Synthesis and modification of reduced graphene oxide aerogels for biofuel cell applications
PublikacjaWe have carried out the preparation of reduced graphene oxide aerogels using eco-friendly method that is based on the Hummers method of graphite oxidation without the use of NaNO3 that produces toxic gases. To obtain a porous 3D structure of reduced graphene oxide, we performed the hydrothermal reduction at elevated temperature. We also prepared the rGO aerogel/CNT composite using multiwalled carbon nanotubes as linkers. The rGO...
-
Influence of Surface Modification of Titanium and Its Alloys for Medical Implants on Their Corrosion Behavior
PublikacjaTitanium and its alloys are often used for long-term implants after their surface treatment. Such surface modification is usually performed to improve biological properties but seldom to increase corrosion resistance. This paper presents research results performed on such metallic materials modified by a variety of techniques: direct voltage anodic oxidation in the presence of fluorides, micro-arc oxidation (MAO), pulse laser treatment,...
-
TiO2 nanotube arrays-based reactor for photocatalytic oxidation of parabens mixtures in ultrapure water: Effects of photocatalyst properties, operational parameters and light source
PublikacjaSelf-organized TiO2 nanotubes as immobilized photocatalysts were evaluated in detail for the photocatalytic degradation of parabens mixtures from ultrapure water. This kind of approach can be a very suitable option for emerging contaminants degradation considering the possibility of the catalyst reuse and recovery which will be simpler than when catalytic powders are used. The anodization method was applied for the TiO2 nanotubes...
-
3D Printing of Metallic Implants
PublikacjaThe fabrication of various elements, solid and open porous structures of stainless steel and Ti alloy is described. The process was started with the design of 3D models in CAD/CAM system. The 3D models were transformed into *.stl files and then the manufacturing process of the real structures by means of the selective laser melting with the SLM Realizer 100 3D printer was made. The paper shows the porous specimens made for possible...
-
Enzyme Conjugation - A Promising Tool for Bio-catalytic and Biotransformation Applications – A Review
PublikacjaEnzymes have revolutionized conventional industrial catalysts as more efficient, eco-friendly, and sustainable substitutes that can be used in different biotechnological processes, food, and pharmaceutical industries. Yet, the enzymes from nature are engineered to make them adapt and enhance their durability in the industrial environment. One promising approach involves the combined use of multiple enzymes that catalyze highly...
-
An investigation of microstructural basis for corrosion behavior of Al-CNT composites fabricated by SPS
PublikacjaIn this research effect of the addition of multi-wall carbon nanotubes (MWCNTs) as additive powder on microstructure and corrosion behavior of fabricated Al-CNT composites was studied. The aluminum powder and CNTs were mixed with high energy planetary ball-mill. It is observed that by increasing milling time, the uniformity of CNTs on aluminum matrix and consequently corrosion resistance of Al-CNT composite is increased. On the...
-
TiO 2 Co x O y composite nanotube arrays via one step electrochemical anodization for visible light–induced photocatalytic reaction
PublikacjaTiO2CoxOy (x = 1, y = 1 or x = 3, y = 4) composite photocatalysts have been synthesized via one step anodic anodization of TiCo alloys. The effects of the cobalt content in the alloy (5, 10 and 15 wt%), water content (2, 5 and 10%) in the electrolyte solution, and applied voltage (30, 40 and 50 V) during the anodization process on the morphology and surface properties. Additionally, the dependence of cobalt content in the nanotubes...
-
A new simple approach to prepare rare-earth metals-modified TiO2 nanotube arrays photoactive under visible light: Surface properties and mechanism investigation
PublikacjaApplication of Ti90RE10 alloys (RE = Ho, Er, Nd, Y, Ce, Tm) as a working electrode, instead of Ti pure foil in anodic oxidation in a fluoride-based electrolyte, resulted in formation of well-ordered nanotubes made of TiO2 and RE2O3 mixture, which could be efficiently used for pollutant removal from water and air phase upon UV and visible irradiation and easily separable from the reaction mixture to recycle. The as-prepared NTs...
-
On mechanics of piezocomposite shell structures
PublikacjaThis study presents an original and novel investigation into the mechanics of piezo-flexo-magneto-elastic nanocomposite doubly-curved shells (PFMDCSs) and the ability to detect the lower and higher levels of electro-magnetic fields. In this context, by utilizing the first-order shear deformation shell model, stresses and strains are acquired. By imposing Hamilton's principle and the von Kármán approach, the governing equations...
-
Physicochemical studies (BET) of nanoparticles used for 3D printable conductive composites
Dane BadawczeThis dataset contains physico-chemical examination of fillers used to fabricate new 3D printing-dedicated composites with poly-lactic acid (PLA), carbon black (CB) and nanodiamond fillers. Geometric surface area of the nanoparticles was studied by Brunauer–Emmett–Teller (BET) adsorption/desorption isotherms. Investigated samples: CB Ensaco 250G, detonation...
-
Widening of the electroactivity potential range by composite formation – capacitive properties of TiO2/BiVO4/PEDOT:PSS electrodes in contact with an aqueous electrolyte
PublikacjaComposites based on the titania nanotubes were tested in aqueous electrolyte as a potential electrode material for energy storage devices. The nanotubular morphology of TiO2 was obtained by Ti anodization. TiO2 nanotubes were covered by a thin layer of bismuth vanadate using pulsed laser deposition. The formation of the TiO2/BiVO4 junction leads to enhancement of pseudocapacitance in the cathodic potential range. The third component,...
-
Understanding Fuel Saving and Clean Fuel Strategies Towards Green Maritime
PublikacjaDue to recent emission-associated regulations imposed on marine fuel, ship owners have been forced to seek alternate fuels, in order to meet the new limits. The aim of achieving low-carbon shipping by the year 2050, has meant that alternative marine fuels, as well as various technological and operational initiatives, need to be taken into account. This article evaluates and examines recent clean fuels and novel clean technologies...