Wyszukiwarka
Filtry
wszystkich: 1604
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: HEAT-RESISTIVE STEELS
-
Properties of Vacuum Sintered Duplex Stainless Steels
Publikacja -
Properties of vacuum sintered duplex stainless steels
Publikacja -
Properties of Vacuum Sintered Duplex Stainless Steels
Publikacja -
Sintered Duplex Stainless Steels Corrosion Properties
Publikacja -
Sintered Duplex Stainless Steels Corrosion Properties
Publikacja -
Hydrogen Damage in Superaustenitic 904L Stainless Steels
Publikacjaresults on the influence of hydrogen on corrosion resistance and of hydrogen embrittlement of 904L superaustenitic stainless steel were investigated. The cracking behavior was studied by performing a slow strain rate test in synthetic seawater under varying cathodic polarization conditions. The results showed that the steel’s plasticity varied with the applied cathodic current density. Significant reductions in ductility were found,...
-
Measurements of the mechanical Barkhausen noise in ferromagnetic steels
PublikacjaArtykuł ten przedstawia wpływ zmian w mikrostrukturze stali P91, powstałych w skutek obróbki cieplnej, na właściwości mechanicznego efektu Barkhausena (MeBN). Parametry takie jak amplituda obwiedni napięcia skutecznego (RMS) MeBN oraz położenie maksimum tejże obwiedni porównywane są, pod kątem czułości na obróbkę cieplną materiału, z klasycznymi parametrami takimi jak pole koercji magnetycznej czy też twardość mechaniczna HV. Największą...
-
An advanced thermal-FSI approach of an evaporation of air heat pump
PublikacjaThe paper presents selected problems of numerical modeling of an advanced thermal-FSI approach of evaporator of air heat pomp. The example of a fin-tube evaporator has been studied, focusing on obtaining of heat exchanger characteristics applying two-phase flow model for the in-tube refrigerant flow. Special attention is given to heat transfer between separated medium for different air velocity and changed refrigerant mass flow...
-
Microwave heat treatment application to pasteurization of human milk
PublikacjaA prototype of microwave pasteurizer has been proposed as an alternative for holder pasteurization (HP) routinely used in Human Milk Bank (HMB), ensuring microbiological safety of human milk (HM). It was shown that the time of heat generation was about 15–16 min shorter by applying the microwave than in HP. Total inactivation of heat-sensitive bacteria Escherichia coli, Pseudomonas aeruginosa, Staphylococcus aureus, and Staphylococcus...
-
CAPABILITY OF IDENTIFYING AND PREDICTING THE TECHNICAL CONDITION OF PLATE HEAT EXCHANGERS IN OPERATION
PublikacjaThe paper presents a test stand for plate heat exchangers, allowing to identify the technical condition and to predict durability of the heat exchangers used aboard the sea-going ships: ”Oceanograf”, ”Władysław Orkan”and a passenger-car ferry, under the condition that they are of the same type and manufactured by the same company. In the first part three different installations with plate heat exchangers in the engine rooms...
-
Exergy analysis of the Szewalski cycle with a waste heat recovery system
PublikacjaThe conversion of a waste heat energy to electricity is now becoming one of the key points to improve the energy efficiency in a process engineering. However, large losses of a low-temperature thermal energy are also present in power engineering. One of such sources of waste heat in power plants are exhaust gases at the outlet of boilers. Through usage of a waste heat regeneration system it is possible to attain a heat rate of approximately...
-
Heat Turbomachinery - lab classes
Kursy Online -
Heat Turbomachinery - lab classes
Kursy Online -
Heat Turbomachinery lab classes
Kursy Online -
Recent Advances in Loop Heat Pipes with Flat Evaporator
PublikacjaThe focus of this review is to present the current advances in Loop Heat Pipes (LHP) with flat evaporators, which address the current challenges to the wide implementation of the technology. A recent advance in LHP is the design of flat-shaped evaporators, which is better suited to the geometry of discretely mounted electronics components (microprocessors) and therefore negate the need for an additional transfer surface (saddle)...
-
Distribution of heat generated by a local heat source
PublikacjaW pracy przedstawiono analizę rozpływu ciepła wygenerowanego przez lokalne źródło umieszczone w płycie, po której przepływa warstwa wody.
-
Numerical analysis of high temperature minichannels heat exchanger performance
PublikacjaNowadays, the most difficult technological challenge in energy sector is connected with the gas micro-CHP units, dedicated to the distributed power generation. They are expected to be of high efficiency and at the same time of compact in size. Regarding the first reason, significant increase in microturbine efficiency can only be achieved by increase in the engine operating temperature. Therefore, one of the critical elements in...
-
Modelling of the Heat Flux Density Distribution for Laser Beam Welding
PublikacjaGreat interest of the laser beam welding in industry is a new theoretical task, making planning the welding procedure specification and the quality control of welded joints easier. Estimating and calculating the dimensions of a weld pool and temperature distribution near weld mainly concern heat source modelling. In the presented work calculations of welding pool shape and thermal field for cylindrical-powered-normally model of...
-
Modelling of heat and mass transfer through wooden buildings
PublikacjaThe aim of this review paper is to examine the most recent available studies dealing with theoretical, numerical and experimental aspects related to modelling of heat and mass transfer through wooden buildings. The main thermophysical, mechanical and hygrometric properties of wood are firstly discussed. Then, the basic governing equations of heat and mass transfer phenomena are presented. A detailed description of the physical...
-
Thermal Analysis Of Hybrid Microchannel-Microjet Heat Exchanger
PublikacjaThe paper presents the numerical investigation of a microjet- microchannel cooling module. In which microjets of water are impinging into the microchannels and forming a liquid film on the impingement surface. Applied technology takes benefits from two very attractive heat removal techniques. When laminar jets are impinging on the surface have a very high kinetic energy at the stagnation point, also in microchannels boundary layer...
-
Heat transfer characteristics of hybrid microjet – Microchannel cooling module
PublikacjaThe paper presents experimental investigation of heat transfer intensification in a microjet–microchannel cooling module. Applied technology takes benefits from two very attractive heat removal techniques. When jets are impinging on the surface, they have a very high kinetic energy at the stagnation point, also in microchannels boundary layer is very thin allowing to obtain very high heat fluxes. Main objective of this paper was...
-
Small wood waste fired combined heat and power plant. Possible use of wood biomass for the generation of electric and heat energy as an alternative to fossil fuels
PublikacjaThis article discusses the possibility of burning wood biomass instead of fossil fuels in boilers. It describes the properties of wood biomass, including the variation of its calorific value depending on the moisture content of wood. The article proposes several variants of a combined heat and power plant (CHP) system burning wood biomass for the generation of electric and heat energy, using the energy contained in exhaust gases...
-
Recuperator with microjet technology as a proposal for heat recovery from low-temperature sources
PublikacjaA tendency to increase the importance of so called dispersed generation, based on the local energy sources and the working systems uti- lizing both the fossil fuels and the renewable energy resources is observed nowadays. Generation of electricity on industrial or domestic scale together with production of heat can be obtained for example through employment of the ORC systems. It is mentioned in the EU directive 2012/27/EU for...
-
Heat transfer characteristics of hybrid microjet -microchannel cooling module
PublikacjaThe paper presents the experimental investigation of heat transfer intensification in a microjet- microchannel cooling module. Applied technology takes benefits from two very attractive heat removal techniques. When jets are impinging on the surface, they have a very high kinetic energy at the stagnation point, also in microchannels boundary layer is very thin allowing to obtain very high heat fluxes. Main objective of this paper...
-
Thermohydraulic maldistribution reduction in mini heat exchangers
PublikacjaA detailed numerical investigation has been carried out to analyze the flow maldistribution in 50 parallel 1 mm × 1 mm rectangular minichannels and 1 mm depth minigap section with rectangular, trapezoidal, triangular or concave manifolds in Z-type flow configuration. The working medium was ethanol and the mass flow rate was 5 × 10−4 kg/s. Both sections were heated from the bottom side. Heat flux of 10 000 W/m2 and 5000 W/m2 was...
-
High-efficiency mini and micro heat exchangers for dispersed power generation
PublikacjaTaking into account the dispersed systems technologies and their development, the ORC systems seem to be promising technology amongst various micro-CHP domestic units (electrical power production below 10 kWe), however practical realization of the ORC cycle in a micro-scale is technically challenging. The system consists in devices such as the vapour generation unit (boiler), expansion device and heat exchangers. Each of them should...
-
Passive Methods in Heat Transport
Kursy Online -
Heat capacities and thermodynamic properties of antimony substituted lanthanum orthoniobates
PublikacjaThe results of heat capacity measurements for the lanthanum orthoniobate substituted with 10, 20 and 30 mol% of antimony (LaNb0.9Sb0.1O4, LaNb0.8Sb0.2O4 and LaNb0.7Sb0.3O4) are presented and discussed. Temperature dependence of low temperature heat capacity was analyzed within the Debye and Einstein models. The Debye temperature decreased, whereas the Einstein temperature increased with antimony content. The decrease of the Debye...
-
Decision support system for design of long distance heat transportation system
PublikacjaDistrict Heating (DH) systems are commonly supplied using local heat sources. Nowadays, modern insulation materials allow for effective and economically viable heat transportation over long distances (over 20 km). The paper proposes a Decision Support System (DSS) for optimized selection of design and operating parameters of a long distance Heat Transportation System (HTS). The method allows for evaluation of feasibility and effectiveness...
-
Recuperator with microjet technology as a proposal for heat recovery from low-temperature sources
PublikacjaA tendency to increase the importance of so called dispersed generation, based on the local energy sources and the working systems utilizing both the fossil fuels and the renewable energy resources is observed nowadays. Generation of electricity on industrial or domestic scale together with production of heat can be obtained for example through employment of the ORC systems. It is mentioned in the EU directive 2012/27/EU for cogenerative...
-
The low temperature waste heat recovery in drying process of pine wood using micro-jet heat exchanger
PublikacjaThe article presents the influence of the drying medium temperature changes for the relative and absolute moisture content values during pine wood drying. The drying process was conducted at constant atmospheric pressure and with different drying medium (air) temperature levels, respectively: 40oC, 60oC, 80oC, 100oC, and 120oC. In order to develop a method that would enable low temperature drying of solid materials the experiments...
-
Effect of Temperature and Nanoparticle Concentration on Free Convective Heat Transfer of Nanofluids
PublikacjaA theoretical analysis of the influence of temperature and nanoparticle concentration on free convection heat transfer from a horizontal tube immersed in an unbounded nanofluid was presented. The Nusselt (Nu) number and heat transfer coefficient were parameters of the intensity of the convective heat transfer. For free convection, the Nu number was a function of the Rayleigh (Ra) number and Prandtl (Pr) number. The Rayleigh (Ra)...
-
Thermal performance of a prototype plate heat exchanger with minichannels under boiling conditions
PublikacjaTo solve the problem and to meet the requirements of customers in the field of high heat fluxes transfer in compact units, a new design of plate heat exchanger with minichannels (minichannels PHE) was proposed. The aim was to construct a compact heat exchanger of high effectiveness for the purpose of household cogeneration ORC system. In this paper the experimental analysis of an assembled prototype of such compact heat exchanger...
-
A simple approach to heat exchanger sizing optimisation by means of entrophy generation minimisation
PublikacjaIn the paper an attempt is presented to find the method of optimization of microtube diameter with respect to optimal thermal-hydraulic conditions in the single-phase shell-and-tube heat exchangers. The approach is based on consideration of pumping power at the condition of maximum heat transfer by the heat exchanger tube system. In the optimization method the tube diameter is first specified and then appropriate calculations are...
-
Performance of a plate heat exchanger operated with water-Al2O3 nanofluid
PublikacjaThis study is focused on experimental investigation of a selected type of brazed plate heat exchanger (PHEx). The main aim of the paper was to experimentally check the ability of nanofluids to enhance the performance of PHEx. A typical water-Al2O3 nanofluid was tested and compared to that of the base fluid, i.e. water. Nanoparticles were tested at the concentration of 0.1% and 1% by weight. Impact of the 1 day and 3 days break...
-
Performance of a plate heat exchanger operated with water-Al2O3 nanofluid
PublikacjaThis study is focused on experimental investigation of a selected type of brazed plate heat exchanger (PHEx). The main aim of the paper was to experimentally check the ability of nanofluids to enhance the performance of PHEx. A typical water-Al2O3 nanofluid was tested and compared to that of the base fluid, i.e. water. Nanoparticles were tested at the concentration of 0.1% and 1% by weight. Impact of the 1 day and 3 days break...
-
Performance of a plate heat exchanger operated with water-Al2O3 nanofluid
PublikacjaThis study is focused on experimental investigation of a selected type of brazed plate heat exchanger (PHEx). The main aim of the paper was to experimentally check the ability of nanofluids to enhance the performance of PHEx. A typical water-Al2O3 nanofluid was tested and compared to that of the base fluid, i.e. water. Nanoparticles were tested at the concentration of 0.1% and 1% by weight. Impact of the 1 day and 3 days break...
-
EFFECT OF NANOFLUID CONCENTRATION ON TWO-PHASE THERMOSYPHON HEAT EXCHANGER PERFORMANCE
PublikacjaAn approach – relaying on application of nanofluid as a working fluid, to improve performance of the two-phase thermosyphon heat exchanger (TPTHEx) has been proposed. The prototype heat exchanger consists of two horizontal cylindrical vessels connected by two risers and a downcomer. Tube bundles placed in the lower and upper cylinders work as an evaporator and a condenser, respectively. Distilled water and nanofluid water-Al2O3...
-
Two-phase thermosiphon heat exchanger for heat recovery
PublikacjaW pracy przedstawiono wyniki badań eksperymentalnych dotyczących wpływu geometrii pęku rur, rodzaju powierzni przejmowania ciepła parownika oraz płynu pośredniego na całkowitą wydajność dwufazowego termosyfonowego wymiennika ciepła (DTWC). Badaniu poddano sześć prototypowych DTWC z dwiema podziałkami rur w parowniku, dla trzech rodzajów powierzchni rur parownika oraz z zastosowaniem trzech rodzajów płynów pośrednich. Lepszą wydajność...
-
Boiling heat transfer performance of the thermosiphon heat exchanger
PublikacjaPrzedstawiono wyniki badań eksperymentalnych prototypowego, termosyfonowgo wymiennika ciepła. W szczególności określono wpływ geometrii pęku rur, stanu powierzchni rurek oraz poziomu cieczy w parowniku na wydajność cieplną wymiennika.
-
Optimization of the distance between the vertical plates in the convective air heat exchanger
PublikacjaThis paper examines the influence of the distance between vertical plates on the intensity of free convective heat transfer along with the optimization of this distance. Experimental tests were carried out for one model channel of such an heat exchanger with widths , 0.085 and 0.18 m. This channel, open at the top and sides, was formed by two isothermal symmetrically heated parallel vertical plates of dimensions m and m. The influence...
-
Performance of the very high-temperature heat pump with low GWP working fluids
PublikacjaTraditional heat pumps are a very attractive pro-ecological solutions for a number of applications, including providing of heating or heat recovery from industrial processes. The application range of heat pumps could be greatly enlarged when the operating temperature would be increased to 130-150°C and/or the temperature lift can be increased to 50-100 K. In the paper, the very high temperature vapour-compressor based single stage...
-
Modeling of Passive and Forced Convection Heat Transfer in Channels with Rib Turbulators
PublikacjaThe main goal of the research presented in this paper was the experimental and numerical analysis of heat enhancement and aerodynamic phenomena during air flow in a channel equipped with flow turbulators in the form of properly configured ribs. The use of ribs intensifies the heat transfer and at the same time increases not only the flow resistance but also the energy costs. Therefore, designing modern heat exchangers with optimal...
-
Flow maldistribution and its mitigation in mini heat exchangers
PublikacjaIn the present paper, a detailed numerical investigation has been carried out to analyze the flow maldistribution in 50 parallel 1 mm x 1 mm rectangular minichannels and 1 mm depth minigap section with rectangular, trapezoidal, triangular or concave mani-folds in Z-type flow configuration (16 different cases). The working medium was ethanol and the mass flow rate was 5×10-4 kg/s. Both sections was heated from the bottom side. Heat...
-
ANALYSIS OF DIESEL OIL SPECIFIC HEAT IMPACT FOR OPERATION OF THE SUPPLY PUMP
PublikacjaThe article describes a test rig that allows the measurement of fuel oil specific heat changes based on the cooling time of liquids. After that, by analysing the test results, a research hypothesis was created and verified. The hypothesis is that the specific heat energy of fuel oil impact the operation of the circulation pump.
-
Phosphorylation‐mediated regulation of heat shock response in Escherichia coli
PublikacjaEscherichia coli has two heat shock regulons under the transcriptional control of Esigma(32) and Esigma(E) RNA polymerases. These polymerases control the expression of genes, the products of which are needed for correct folding of proteins in the cytoplasm and the extracytoplasm respectively. In this study, we report that mutations in a tyrosine phosphatase-encoding gene led to decreased activity of these heat shock regulons. The...
-
Influence of the thermal modernization of window on transmission heat losses
PublikacjaThe article presents the results of calculations of the heat transfer coefficient for the state before and after renovation for the historic windows. The aim of the analysis was to obtain the values of thermal insulation parameters demanded by the regulations, while not losing the historical value of the window. The described example of the renovation of the existing window consisted in installing an additional window panel from...
-
Microjet technology as a perspective intensification method for high performance heat exchangers
PublikacjaIn the paper two oryginal designs of compact heat exchangers with intensification effect produced by microjets are presented. The technology of microjets manufacturing is an "inhouse" patented design. The idea of such heat exchanger is shown together with the flow and thermal characteristics of the prototypes. The results of performer measurements are satisfactory and encourage for further research of the original designs.
-
Environmental degradation of the Cr-Mo steels in liquid hydrocarbons
PublikacjaPrzedstawiono podatność stali stopwych 26H2MF i 34HNM do naprężeniowego pękania korozyjnego. Środowiskiem do badań było paliwo ciężkie i zużyty olej mineralny.
-
Hydrogen degradation of structural steels in technical hydrocarbon liquids
PublikacjaDla stali stopowych przeprowadzono badania absorpcji wodoru, mechaniczno-korozyjne przy stałej małej prędkości odkształcania, przy stałym obciążeniu i przy obciążeniu cyklicznie-zmiennym. Środowiskiem było paliwo kotłowe, przepracowany olej mineralny oraz gliceryna. Stwierdzono, iż pochłonięty wodór nie powoduje przedwczesnego zniszczenia stali poddanych działaniu stałego obciążenia ponizej granicy plastyczności oraz, że zaabsorbowany...