Wyniki wyszukiwania dla: simulation of heat and mass transfer
-
Heat transfer intensification by jet impingement – numerical analysis using RANS approach
PublikacjaJet impingement is a method of the heat transfer enhancement applied in the engineering systems. The idea is to generate fast-flow fluid jet which impinge on the heated (or cooled) surface, causing significantly higher heat transfer rate. Although some flat surface jet impingement cases are described in the literature, the validated data is still limited. The reason is coming from the fact, that these flows are hydrodynamically...
-
Influence of nanoparticle concentration on convective heat transfer of water-Al2O3 nanofluids inside horizontal tubes
PublikacjaNanofluids came to be seen as a new generation of coolants, especially in single-phase systems. Conducted experiments indicate that the increase in thermal conductivity is not the only reason for the intensification of heat transfer when using nanofluids. Preliminary results of the experimental investigation of the forced convection heat transfer of water-Al2O3 nanofluids inside stainless steel tube with 8 mm internal diameter...
-
Experimental study of boiling heat transfer in the stagnation point of water microjet
PublikacjaIn the paper presented is a comparison of computational model with experimental data. Numerical model of liquid film with phase change in the stagnation zone due to impingement of the microjet is more widely presented in authors previous work. The radius on which theevaporation process is taking place can be determined from the energy balance on the element of the plate. That radius has also been confirmed experimentally in the...
-
Angular welding distortion - one sided fillet weld
Dane BadawczeWelding is the basic method of joining ship hull elements during its construction. However, this method of joining structural elements generates shrinks. Shrinks causes deformation of the entire welded structure, both linear and angular. In the shipbuilding industry, there is a tendency to oversize fillet welds, at the design as well as manufacturing...
-
Modelling study of flow boiling heat transfer of perspective fluids for refrigeration technology
PublikacjaThere is a gap of knowledge on flow boiling at high saturation temperatures and higher values of reduced pressure. Thus far, the in-house developed semi-empirical model for flow boiling and flow condensation showed a satisfactory accuracy for calculations for various refrigeration fluids for a wide scope of reduced pressures. This study presents results of calculations of heat transfer coefficient of perspective refrigeration fluids,...
-
Pressure drop and heat transfer during boiling and condensation at subcritical region
PublikacjaMost of the data presented in the literature relate to saturation temperatures in the range - 20°C to 40°C due to the application in refrigeration technology. There is necessity to extend databases to higher values of saturation temperature due to new applications such as Organic Rankine Cycle and high temperature heat pumps. Only few papers contain data for high reduced pressure for low boiling point liquids. This paper focus...
-
Comparison of predictive methods for flow boiling heat transfer in conventional channels and minichannels - the effect of reduced pressure
PublikacjaIn the paper are presented the results of follow on studies from [1]–[3] using authors own model to predict heat transfer coefficient during flow boiling. The model has been tested against a large selection of experimental data collected from various researchers to investigate the sensitivity of the in-house developed model. The collected experimental data came from various studies from literature and were conducted for the full...
-
Impact of Temperature and Nanoparticle Concentration on Turbulent Forced Convective Heat Transfer of Nanofluids
PublikacjaTheoretical analysis of the influence of nanoparticles and temperature on the average Nusselt (Nu) number and the average heat transfer coefficient (HTC) during the turbulent flow of nanofluid in a horizontal, round tube was carried out. The Nu number is a function of the Reynolds (Re) number and the Prandtl (Pr) number, which in turn are functions of the thermophysical properties of the liquid and the flow conditions. On the other...
-
Impact of the inclination angle of the condenser with refrigerant R410A on heat transfer coefficient – experimental study
PublikacjaIn the paper the authors present results of a laboratory test of the condenser with refrigerant R410A. The effect of the inclination of this condenser on the heat transfer coefficient value has been considered. The test has proved that there is an optimal inclination angle of the condenser which gives maximal value of this coefficient.
-
Comparison of heat transfer characteristics in surface cooling using microjets with water, ethanol and HFE7100 as test fluids
PublikacjaAccurate control of cooling parameters is required in ever wider range of technical applications. It is known that reducing the dimensions of the size of nozzle leads to an increase in the economy of cooling and improves its quality. Present study describes research related to the design and construction of the nozzles and microjet study, which may be applied in many technical applications such as in metallurgy, electronics, etc....
-
Boiling heat transfer performance of the thermosiphon heat exchanger
PublikacjaPrzedstawiono wyniki badań eksperymentalnych prototypowego, termosyfonowgo wymiennika ciepła. W szczególności określono wpływ geometrii pęku rur, stanu powierzchni rurek oraz poziomu cieczy w parowniku na wydajność cieplną wymiennika.
-
Heat Transfer of the Multicolor-Laser-Sources-Irradiated Nanoparticles in Reference to Thermal Processes
PublikacjaUnlike the standard materials, metallic nanoparticles offer enhancing the heat convertion rate which implies the maximum and average temperature boost significantly in the considered system. The work’s purpose is to examine heat transfer in the metallic nanoparticles which have been deposited on a glassy substrate, enabling the nanostructures thermoablation. Furthermore, the functionalized substrate is irradiated with multicolor-laser-sources,...
-
Numerical analysis of the two‐phase steam‐air heat transfer flow induced in smooth and corrugated channel using the VOF model
Publikacja -
A common method for calculation of flow boiling and flow condensation heat transfer coefficients in minichannels with account of nonadiabatic effects
PublikacjaW pracy przedstawiono metodę ogólną wyznaczania współczynników przejmowania ciepła podczas wrzenia w przepływie i kondensacji w przepływie w minikanałach z uwzględnieniem efektu nieadiabatycznego. Uwzględnia ona wpływ modyfikacji naprężeń stycznych na granicy ciecz-para na wymianę ciepła.
-
Experimental investigation of M-shape heat transfer coefficient distribution of R123 flow boiling in small-diameter tubes
PublikacjaW publikacji przedstawiono wyniki badań wrzenia czynnika R123 w srebrnych rurkach o małych średnicach (średnice wewnętrzne wynosiły odpowiednio 1.15 mm i 2.3 mm). Badania przeprowadzono w szerokim zakresie stopnia suchości pary (0.01-0.9), gęstości strumienia masy (650-3000 kg/(m2s)) oraz gęstości strumienia ciepła (40-80 kW/m2). W badaniach wykazano, że istnieją dwa lokalne maksima współczynnika przejmowania ciepła w jego profilu...
-
COMPARISON OF PREDICTIVE METHODS FOR FLOW BOILING HEAT TRANSFER IN CONVENTIONAL CHANNELS AND MINICHANNELS – THE EFFECT OF REDUCED PRESSURE
PublikacjaIn the paper are presented the results of follow on studies from [1]–[3] using authors own model to predict heat transfer coefficient during flow boiling. The model has been tested against a large selection of experimental data collected from various researchers to investigate the sensitivity of the in-house developed model. The collected experimental data came from various studies from literature and were conducted for the full...
-
Influence of nanoparticle concentration on convective heat transfer of water-Al2O3 nanofluids inside horizontal tubes
PublikacjaThis work presents preliminary results of the experimental investigation of the forced convection heat transfer of water-Al2O3 nanofluids inside stainless steel tube with 8 mm internal diameter and 2000 mm length. Nanoparticles were tested at the concentrations of 0.01%, 0.1%, 1% and 5% by weight and the Reynolds number range encompasses laminar as well as turbulent flows.
-
Heat transfer characteristics of a two-phase thermosyphon heat exchanger
PublikacjaPrzedstawiono wyniki badań wpływu geometrii parownika, rodzaju rur użytych do budowy parownika, rodzaju cieczy pośredniej oraz poziomu cieczy nad najwyższym rzędem rur na działanie dwufazowego, termosyfonowego wymiennika ciepła. Zaprezentowano algorytm obliczeń przedstawionego wymiennika.
-
Numerical Investigation of Nuclear Reactor Kinetic and Heat Transfer Fractional Model with Temperature Feedback
PublikacjaAbstract—In the paper, the numerical results concerning the kinetics and proposed heat exchange models in nuclear reactor based on fractional calculus are presented for typical inputs. Two fractional models are proposed and compared with the model based on ordinary derivative. The first fractional model is based on one of the generalized Cattaneo equations. The second one is based on replacing the ordinary to fractional order of...
-
Implementation of the Boundary Element Method to Two-Dimensional Heat Transfer with Thermal Bridge Effects
PublikacjaThe work presents an application of the boundary element method applied to a two-dimensional conductive heat transfer. The algorithm of the method is explained and its advantages are outlined. Green's function as a fundamental solution for Poisson's equation in two dimensions was used and the direct approach was applied. The presented results concern building construction elements as typical cases of thermal bridges. Some properties...
-
Simplified modelling of heat transfer in groundwater
PublikacjaPrzenoszenie ciepła w wodach podziemnych jest skomplikowanym, przestrzennym procesem. Z tego względu do rozwiązywania zadań praktycznych celowe jest konstruowanie modeli uproszczonych. W pracy zaproponowano sposób formułowania modelu dwuwymiarowego. Został on pozytywnie zweryfikowany na przykładzie badania przyczyn strat energii cieplnej w elektrowni Kozienice.
-
Modelling of heat transfer in flow boiling
PublikacjaW pracy przedstawiono zagadnienia związane z modelowaniem wrzenia w przepływie w kanałach o małej średnicy. Przedstawiono modyfikację rozwijanej przez autorów korelacji umożliwiającej wyznaczanie współczynnika przejmowania ciepła podczas wrzenia w przepływie.
-
On-line assessment of oil quality during deep frying using an electronic nose and proton transfer reaction mass spectrometry
PublikacjaWe describe a novel method for the quality assessment of oil utilized for deep frying. The method is based on the analysis of frying fumes using a custom electronic nose. The quality score could be obtained after less than 3 min of analysis and without interrupting the frying process or sampling the oil directly. The obtained results were correlated with the peroxide value using a multivariate linear regression model. The most...
-
Comparitive study of heat transfer and pressure drop during flow boiling and flow condensation in minichannels
PublikacjaIn the paper a method developed earlier by authors is applied to calculations of pressure drop and heat transfer coefficient for flow boiling and also flow condensation for some recent data collected from literature for such fluids as R404a, R600a, R290, R32,R134a, R1234yf and other. The modification of interface shear stresses between flow boiling and flow condensation in annular flow structure are considered through incorporation...
-
THREE-DIMENSIONAL numerical investigation of MHD nanofluid convective heat transfer inside a CUBIC porous container with corrugated bottom wall
PublikacjaSimultaneous use of porous media and nanofluid as a heat transfer improvement method has recently captivated a great deal of attention. The heat transfer and entropy production of the Cu-water nanofluid inside a cubic container with a heated bottom wavy wall and an elliptic inner cylinder were numerically analyzed in this study. The container is partitioned into two sections: the left side is filled with permeable media and...
-
Numerical simulation of temperature distribution of heat flow on reservoir tanks connected in a series
PublikacjaThe flow of temperature distribution through a medium in thermodynamic studies plays an important role in understanding physical phenomena in chemical science and petroleum engineering, while temperature distribution indicates the degree of reaction that must be undergone to obtain the final product. Therefore, this paper aims to present and apply the exponential matrix algorithm (EMA), differential transformation algorithm (DTA),...
-
Possibilities of heat transfer augmentation in heat exchangers with minichannels for marine applications
PublikacjaIn the paper, new trends in development of microchannel heat exchangers are presented. The exchangers developed in this way can be applied in marine applications. Main attention was focused on heat exchangers design with reduced size of passages namely based on microchannels. In our opinion future development of high power heat exchangers will be based on networks micro heat exchangers.
-
Application of Feed Forward Neural Networks for Modeling of Heat Transfer Coefficient During Flow Condensation for Low and High Values of Saturation Temperatur
PublikacjaMost of the literature models for condensation heat transfer prediction are based on specific experimental parameters and are not general in nature for applications to fluids and non-experimental thermodynamic conditions. Nearly all correlations are created to predict data in normal HVAC conditions below 40°C. High temperature heat pumps operate at much higher parameters. This paper aims to create a general model for the calculation...
-
Areas of updraft air motion from WRF model simulations.
Dane BadawczePresented dataset is a part of numerical modelling study focusing on the analysis of sea ice floes size distribution (FSD) influence on the horizontal and vertical structure of convection in the atmosphere. The total area and spatial arrangement of the updrafts indicates that the FSD affects the total moisture content and the values of area averaged...
-
Real-Time Monnitoring of Vegetable Oils' Thermal Degradation Using Proton Transfer Reaction Mass Spectrometry
PublikacjaThe volatile aldehydes, which are generated during frying, can be harmful to human health, therefore the concentration of these compounds in frying fumes should be monitored. In addition, aldehydes are markers of oils’ quality, and so it is possible to determine shelf-life or suitability for frying of these oils. Commonly, in order to determine aldehydes concentration gas chromatography is performed, however it does not allow for...
-
Comparison of heat transfer characteristics in surface cooling with boiling microjets of water, ethanol and HFE7100
PublikacjaThe basis of microjet technology is to produce jets which impinge the surface at the stagnation point with a very high kinetic energy. Main objective of this paper was to investigate the physical phenomena occurring on solid surfaces upon impingement of the single microjet in case of three fluids, namely water, ethanol and HFE7100. Intense heat transfer in the impact zone of microjet has been examined and described with precise...
-
Heat transfer phenomena of glassy carbon foams
Publikacja -
A study of flow boiling heat transfer in minichannels
PublikacjaW pracy przedstawiono badania eksperymentalne wrzenia w przepływie w minikanale o średnicy wewnętrznej 2.3mm i długości 38cm. Uzyskano rozłady temperatury wzdłuż ścianki kanału oraz lokalne współczynniki przejmowania ciepła. Dane skorelowano z korelacją półempiryczną uzyskując zadowalającą zgodność.
-
Modelling of convective heat transfer in flow boiling.
PublikacjaW pracy przedstawiono rozważania dotyczące modelowania przepływu z wrzeniem w zastosowaniu do kanałów o małej średnicy. Stwierdzono,że stosowanie korelacji obowiązujących dla średnic konwencjonalnych nie sprawdza się z praktyką w przypadku małych średnic.
-
Heat transfer augmentation using liquid crystal
PublikacjaPraca przedstawia zastosowanie techniki wizualizacji ciekłokrystalicznej dobadań wymiany ciepła na płaskiej powierzchni z zaburzaczami. Folia ciekło-krystaliczna została umieszczona na powierzchni, aby określić przebieg izoterm. Obraz rejestrowano kamerą JVC, a następnie analizowano komputerowo. Procedura eksperymentalna pozwala na otrzymanie pełnej informacji dotyczącej wymiany ciepła (na powierzchni płaskiej z elementami ustawionymi...
-
The impact of nozzle configuration on the heat transfer coefficient
Publikacja -
Theoretical analysis of heat transfer between a liquid layer formed by an impinginf gas liquid jet AND a solid surface
PublikacjaHeat transfer phenomenon between a horizontal solid surface and a liquid layer created on a surface by an axisymmetrical liquid gas impinging jet has been analysed. The analytical treatment of the phenomenon is devoted to the area whose diameter is lower than the diameter of the hydraulic jump. W pracy przedstawiono teoretyczną analizę wymiany ciepła pomiędzy warstwą cieczy a stałą powierzchnią po której przepływa.
-
Hydrodynamics and Mass Transfer Analysis in BioFlow® Bioreactor Systems
Publikacja -
Turbulent heat transfer in thin liquid films at low and high heat fluxes
PublikacjaW pracy przedstawiono rozważania turbulentnej wymiany ciepła w cienkich filmach cieczowych powstałych w wyniku uderzenia strugi przy małych i dużych strumieniach ciepła. W ostatnim przypadku może dojść do wrzenia filmu cieczowego. Oba zjawiska zamodelowano i uzyskano odpowiednie rozkłady temperatury i pedkosci.
-
Heat and mass exchange in the process of condensation on critical droplets.
PublikacjaSformułowano model wzrostu kropli krytycznej podając równania zmiany masy i temperatury kropli. Pokazano formę zlinearyzowaną tych równań dobrze aproksymującą wzrost kropli w poblizu wymiaru krytycznego. Podano rozwiązanie układu zlinearyzowanego uzależniając zmianę temperatury od zmiany masy kropli i czasu charakterystycznego.
-
Heat transfer augmentation visualized by liquid crystal thermography
PublikacjaW pracy przedstawiono możliwości wykorzystania termografii ciekłokrystalicznej do badań wymiany ciepła oraz wizualizacji pola przepływu w elementach urządzeń przemysłowych.
-
Determining heat transfer coefficients using evolutionary alogrithms
PublikacjaPokazano sposób kalibracji współczynnika wymiany ciepła za pomocą algorytmów ewolucyjnych. Wykorzystano tu minimalizację błędu między pomiarami a obliczeniami. Pokazano dwie metody optymalizacji: wielokryterialną i jednokryterialną.
-
Heat transfer in fluidized and fixed beds of adsorption chillers
Publikacja -
Analysis of heat transfer in a coated bed of an adsorption chiller
Publikacja -
The use of thermochromic liquid crystals in heat transfer research
PublikacjaW ostatnich latach ciekłe kryształy zostały z powodzeniem zastosowane do wizualizacji pola temperatury w stanach ustalonych i przejściowych na różnych powierzchniach. Analiza otrzymanych obrazów początkowo była skomplikowana, ale dzięki zastosowaniu obróbki komputerowej pomiary stały się o wiele dokładniejsze i szybsze. W opracowaniu przedstawiono przegląd badań, w których zastosowano automatyczną technikę analizy obrazów, a prowadzone...
-
Natural convective heat transfer from isothermal cuboids
PublikacjaPrzestawiono rozważania teoretyczne i wyniki badań eksperymentalnych konwekcyjnej wymiany ciepła od powierzchni izotermicznego prostopadłościanu. W rozwiązaniu analitycznym uwzględniono pełną długość warstwy przyściennej i sposób jej rozchodzenia się wzdłuż powierzchni prostopadłościanu. W celu zweryfikowania otrzymanego rozwiązania przeprowadzono badania eksperymentalne w trzech możliwych położeniach bryły. Zaproponowano uniwersalną...
-
Convective heat transfer inside hemispherical reflective concentrator.
PublikacjaW pracy przedstawiono uproszczone rozwiązanie analityczne, obliczenia numeryczne wykonane za pomocą programu FLUENT/UNS i wyniki badań eksperymentalnych swobodnej konwekcyjnej wymiany ciepła wewnątrz izotermicznej powierzchni kołowej w przestrzeni nieograniczonej. Wykonane obserwacje bezpośrednie konwekcyjnych struktur przepływu, jak i wyniki obliczeń numerycznych otrzymane w postaci pola prędkości i linii prądu wewnątrz...
-
Thermochromic liquid crystals applied for heat transfer research
PublikacjaAutorzy opisali własne wieloletnie doświadczenia z badań wymiany ciepła, w których wykorzystali termochromatyczne ciekłe kryształy. Obejmowały one badania przepływów w kanałach o różnorakiej konfiguracji, badania w przestrzeniach zamkniętych oraz podczas zmiany stanu skupienia badanego płynu.
-
Heat and Mass Transport, Ć, IDE, sem. 01, letni 22/23
Kursy Online -
Direct measurements of odorous volatile organic compounds present in biosolids cakes by Proton Transfer Reaction – Mass Spectrometry Technique
PublikacjaThis paper show the results of investigation of concentration of odorous chemical compounds emitted upon ageing of anaerobically stabilised biosolids that could contribute to the overall odour character of nuisance emissions. Biosolids samples from wastewater treatment plant were collected in spring time. Concentrations of volatile organic compounds using a US EPA flux hood and Proton Transfer Reaction-Time of Flight-Mass Spectrometry...