Wyniki wyszukiwania dla: ELECTROCHEMICAL DEPOSITION METHOD

• International Journal of Electrochemical Science

  Czasopisma

  ISSN: 1452-3981

• Formation of gold anostructures detected by SEM microscope

  Dane Badawcze

  open access

  • M. Łapiński

  Gold nanostructures were prepared on silicon - Si(111) as a substrate. The substrates (1 × 1 cm2  of area) were cleaned with acetylacetone and then rinsed in ethanol. Thin Au films (with thicknesses in a range of 1.7–5.0 nm) were deposited using a table-top dc magnetron sputtering coater (EM SCD 500, Leica) under pure Ar plasma conditions (Argon, Air...

• Primary myelofibrosis - Male, 66 - Tissue image [11290630017293981]

  Dane Badawcze

  open access

  • Gdański Uniwersytet Medyczny

  This is the histopathological image of HEMATOPOIETIC AND RETICULOENDOTHELIAL SYSTEMS tissue sample obtained in Medical University Gdańsk and deposited in ZMDL-GUMED. The sample image was taken using: Pannoramic 250 3DHistech slide scanner (20x magnification) and saved to DICOM format.

• Temperature measurement of supercapacitor with the use of ZnO coated microsphere-based fiber-optic sensor - 75 Celsius degrees

  Dane Badawcze

  open access

  • P. Listewnik
  • M. Szczerska

  - seria: Measurement spectrum obtained with the use of ALD coated microsphere-based fiber-optic sensor

  Application of a microsphere-based fiber-optic sensor with 200 nm zinc oxide (ZnO) coating, deposited by Atomic Layer Deposition (ALD) method, for temperature measurements of supercapasitor, is presented.  Internal temperature of the supercapacitor is investigated in the range between 30°C and 90°C. The supercapacitor temperature was investigated using...

• Temperature measurement of supercapacitor with the use of ZnO coated microsphere-based fiber-optic sensor - 65 Celsius degrees

  Dane Badawcze

  open access

  • P. Listewnik
  • M. Szczerska

  - seria: Measurement spectrum obtained with the use of ALD coated microsphere-based fiber-optic sensor

  Application of a microsphere-based fiber-optic sensor with 200 nm zinc oxide (ZnO) coating, deposited by Atomic Layer Deposition (ALD) method, for temperature measurements of supercapasitor, is presented.  Internal temperature of the supercapacitor is investigated in the range between 30°C and 90°C. The supercapacitor temperature was investigated using...

• Temperature measurement of supercapacitor with the use of ZnO coated microsphere-based fiber-optic sensor - 90 Celsius degrees

  Dane Badawcze

  wersja 1.0 open access

  • P. Listewnik
  • M. Szczerska

  - seria: Measurement spectrum obtained with the use of ALD coated microsphere-based fiber-optic sensor

  Application of a microsphere-based fiber-optic sensor with 200 nm zinc oxide (ZnO) coating, deposited by Atomic Layer Deposition (ALD) method, for temperature measurements of supercapasitor, is presented.  Internal temperature of the supercapacitor is investigated in the range between 30°C and 90°C. The supercapacitor temperature was investigated using...

• Temperature measurement of supercapacitor with the use of ZnO coated microsphere-based fiber-optic sensor - 80 Celsius degrees

  Dane Badawcze

  open access

  • P. Listewnik
  • M. Szczerska

  - seria: Measurement spectrum obtained with the use of ALD coated microsphere-based fiber-optic sensor

  Application of a microsphere-based fiber-optic sensor with 200 nm zinc oxide (ZnO) coating, deposited by Atomic Layer Deposition (ALD) method, for temperature measurements of supercapasitor, is presented.  Internal temperature of the supercapacitor is investigated in the range between 30°C and 90°C. The supercapacitor temperature was investigated using...

• Temperature measurement of supercapacitor with the use of ZnO coated microsphere-based fiber-optic sensor - 45 Celsius degrees

  Dane Badawcze

  open access

  • P. Listewnik
  • M. Szczerska

  - seria: Measurement spectrum obtained with the use of ALD coated microsphere-based fiber-optic sensor

  Application of a microsphere-based fiber-optic sensor with 200 nm zinc oxide (ZnO) coating, deposited by Atomic Layer Deposition (ALD) method, for temperature measurements of supercapasitor, is presented.  Internal temperature of the supercapacitor is investigated in the range between 30°C and 90°C. The supercapacitor temperature was investigated using...

• Temperature measurement of supercapacitor with the use of ZnO coated microsphere-based fiber-optic sensor - 35 Celsius degrees

  Dane Badawcze

  open access

  • P. Listewnik
  • M. Szczerska

  - seria: Measurement spectrum obtained with the use of ALD coated microsphere-based fiber-optic sensor

  Application of a microsphere-based fiber-optic sensor with 200 nm zinc oxide (ZnO) coating, deposited by Atomic Layer Deposition (ALD) method, for temperature measurements of supercapasitor, is presented.  Internal temperature of the supercapacitor is investigated in the range between 30°C and 90°C. The supercapacitor temperature was investigated using...

• Temperature measurement of supercapacitor with the use of ZnO coated microsphere-based fiber-optic sensor - 50 Celsius degrees

  Dane Badawcze

  open access

  • P. Listewnik
  • M. Szczerska

  - seria: Measurement spectrum obtained with the use of ALD coated microsphere-based fiber-optic sensor

  Application of a microsphere-based fiber-optic sensor with 200 nm zinc oxide (ZnO) coating, deposited by Atomic Layer Deposition (ALD) method, for temperature measurements of supercapasitor, is presented.  Internal temperature of the supercapacitor is investigated in the range between 30°C and 90°C. The supercapacitor temperature was investigated using...

• Temperature measurement of supercapacitor with the use of ZnO coated microsphere-based fiber-optic sensor - 70 Celsius degrees

  Dane Badawcze

  open access

  • P. Listewnik
  • M. Szczerska

  - seria: Measurement spectrum obtained with the use of ALD coated microsphere-based fiber-optic sensor

  Application of a microsphere-based fiber-optic sensor with 200 nm zinc oxide (ZnO) coating, deposited by Atomic Layer Deposition (ALD) method, for temperature measurements of supercapasitor, is presented.  Internal temperature of the supercapacitor is investigated in the range between 30°C and 90°C. The supercapacitor temperature was investigated using...

• Temperature measurement of supercapasitor with the use of ZnO coated microsphere-based fiber-optic sensor - 30 Celsius degrees

  Dane Badawcze

  wersja 1.0 open access

  • P. Listewnik
  • M. Szczerska

  - seria: Measurement spectrum obtained with the use of ALD coated microsphere-based fiber-optic sensor

  Application of a microsphere-based fiber-optic sensor with 200 nm zinc oxide (ZnO) coating, deposited by Atomic Layer Deposition (ALD) method, for temperature measurements of supercapasitor, is presented.  Internal temperature of the supercapacitor is investigated in the range between 30°C and 90°C. The supercapacitor temperature was investigated using...

• Temperature measurement of supercapacitor with the use of ZnO coated microsphere-based fiber-optic sensor - 60 Celsius degrees

  Dane Badawcze

  open access

  • P. Listewnik
  • M. Szczerska

  - seria: Measurement spectrum obtained with the use of ALD coated microsphere-based fiber-optic sensor

  Application of a microsphere-based fiber-optic sensor with 200 nm zinc oxide (ZnO) coating, deposited by Atomic Layer Deposition (ALD) method, for temperature measurements of supercapasitor, is presented.  Internal temperature of the supercapacitor is investigated in the range between 30°C and 90°C. The supercapacitor temperature was investigated using...

• Temperature measurement of supercapacitor with the use of ZnO coated microsphere-based fiber-optic sensor - 40 Celsius degrees

  Dane Badawcze

  open access

  • P. Listewnik
  • M. Szczerska

  - seria: Measurement spectrum obtained with the use of ALD coated microsphere-based fiber-optic sensor

  Application of a microsphere-based fiber-optic sensor with 200 nm zinc oxide (ZnO) coating, deposited by Atomic Layer Deposition (ALD) method, for temperature measurements of supercapasitor, is presented.  Internal temperature of the supercapacitor is investigated in the range between 30°C and 90°C. The supercapacitor temperature was investigated using...

• Temperature measurement of supercapacitor with the use of ZnO coated microsphere-based fiber-optic sensor - 85 Celsius degrees

  Dane Badawcze

  open access

  • P. Listewnik
  • M. Szczerska

  - seria: Measurement spectrum obtained with the use of ALD coated microsphere-based fiber-optic sensor

  Application of a microsphere-based fiber-optic sensor with 200 nm zinc oxide (ZnO) coating, deposited by Atomic Layer Deposition (ALD) method, for temperature measurements of supercapasitor, is presented.  Internal temperature of the supercapacitor is investigated in the range between 30°C and 90°C. The supercapacitor temperature was investigated using...

• Temperature measurement of supercapacitor with the use of ZnO coated microsphere-based fiber-optic sensor - 55 Celsius degrees

  Dane Badawcze

  open access

  • P. Listewnik
  • M. Szczerska

  - seria: Measurement spectrum obtained with the use of ALD coated microsphere-based fiber-optic sensor

  Application of a microsphere-based fiber-optic sensor with 200 nm zinc oxide (ZnO) coating, deposited by Atomic Layer Deposition (ALD) method, for temperature measurements of supercapasitor, is presented.  Internal temperature of the supercapacitor is investigated in the range between 30°C and 90°C. The supercapacitor temperature was investigated using...

• Distance measurement by the low coherent interferometer with NND layer (the source wavelegth 1310 nm)

  Dane Badawcze

  open access

  • M. Szczerska
  • M. Kosowska

  The obtained data was acquired by the interferometric fiber-optic sensor of distance. The setup was constructed of a broadband light source working at the central wavelength of 1310 nm, an optical spectrum analyzer, and a fiber-optic 2x1 coupler (with the power split 50:50). All elements were connected by standard single-mode optical fibers. The measurement...

• Measurement spectrum obtained with the use of ZnO coated microsphere-based fiber-optic sensor - 120 Celsius degrees

  Dane Badawcze

  open access

  • P. Listewnik
  • M. Szczerska

  Application of a microsphere-based fiber-optic sensor with 200 nm zinc oxide (ZnO) coating, deposited by Atomic Layer Deposition (ALD) method, for temperature measurements between 100°C and 300°C, is presented. The main advantage of integrating a fiber-optic microsphere with a sensing device is the possibility of monitoring the integrity of the sensor...

• Measurement spectrum obtained with the use of ZnO coated microsphere-based fiber-optic sensor - 100 Celsius degrees

  Dane Badawcze

  open access

  • P. Listewnik
  • M. Szczerska

  Application of a microsphere-based fiber-optic sensor with 200 nm zinc oxide (ZnO) coating, deposited by Atomic Layer Deposition (ALD) method, for temperature measurements between 100°C and 300°C, is presented. The main advantage of integrating a fiber-optic microsphere with a sensing device is the possibility of monitoring the integrity of the sensor...

• Myelofibrosis as a result of myeloproliferative disease - Male, 71 - Tissue image [11290630017295521]

  Dane Badawcze

  open access

  • Gdański Uniwersytet Medyczny

  This is the histopathological image of HEMATOPOIETIC AND RETICULOENDOTHELIAL SYSTEMS tissue sample obtained in Medical University Gdańsk and deposited in ZMDL-GUMED. The sample image was taken using: Pannoramic 250 3DHistech slide scanner (20x magnification) and saved to DICOM format.

• Measurement spectrum obtained with the use of ZnO coated microsphere-based fiber-optic sensor - 130 Celsius degrees

  Dane Badawcze

  open access

  • P. Listewnik
  • M. Szczerska

  Application of a microsphere-based fiber-optic sensor with 200 nm zinc oxide (ZnO) coating, deposited by Atomic Layer Deposition (ALD) method, for temperature measurements between 100°C and 300°C, is presented. The main advantage of integrating a fiber-optic microsphere with a sensing device is the possibility of monitoring the integrity of the sensor...

• Measurement spectrum obtained with the use of ZnO coated microsphere-based fiber-optic sensor - 110 Celsius degrees

  Dane Badawcze

  wersja 2.0 open access

  • P. Listewnik
  • M. Szczerska

  Application of a microsphere-based fiber-optic sensor with 200 nm zinc oxide (ZnO) coating, deposited by Atomic Layer Deposition (ALD) method, for temperature measurements between 100°C and 300°C, is presented. The main advantage of integrating a fiber-optic microsphere with a sensing device is the possibility of monitoring the integrity of the sensor...

• Plasma-Based Deposition and Processing Techniques for Optical Fiber Sensing

  Publikacja

  • M. Dominik
  • M. Koba
  • R. Bogdanowicz
  • W. Bock
  • M. Śmietana

  - Rok 2017

  Plasma-based techniques are widely applied for well-controlled deposition, etching or surface functionalization of a number of materials. It is difficult to imagine fabrication of novel microelectronic and optoelectronic devices without using plasma-enhanced deposition of thin films, their selective etching or functionalization of their surfaces for subsequent selective binding of chemical or biological molecules. Depending on...

  Pełny tekst do pobrania w serwisie zewnętrznym

• Physics Research Method IV

  Kursy Online

  • J. Guthmuller

  {mlang pl} Dyscyplina:  Nauki Fizyczne Zajęcia obowiązkowe dla doktorantów II roku Prowadzący:   prof. Julien Guthmuller Liczba godzin: 15 h Forma zajęć: wykład/seminarium {mlang} {mlang en} Discipline: Phisical Sciences Obligatory course for 2nd year PhD students Academic teacher:  prof. Julien Guthmuller Total hours of training: 15 teaching hours Course type: lecture/seminar {mlang}

• Degradation of electrical performance of a crystalline photovoltaic module due to dust deposition in northern Poland

  Publikacja

  • E. Klugmann-Radziemska

  - RENEWABLE ENERGY - Rok 2015

  The reduction in power output caused by the accumulation of dust on the photovoltaic module surface is an important problem and should receive much more attention in the literature. This study was an evaluation of the performance degradation of crystalline photovoltaic modules due to natural and simulated dust deposition. Dust is created from powdered grains of sand and particles of different bodies. Dust originates from different...

  Pełny tekst do pobrania w portalu

• Decrease in Photovoltaic Module Efficiency Due to Deposition of Pollutants

  Publikacja

  • E. Klugmann-Radziemska
  • M. Rudnicka

  - IEEE Journal of Photovoltaics - Rok 2020

  The deposition of pollutants on the surface of photovoltaic (PV) modules reduce the efficiency that can be achieved in given climatic conditions. This results in the loss of energy yield obtained from the solar installation. A number of factors determine the scale of this problem. The first of these is the amount of impurities deposited, the associated amount of precipitation, and the speed and direction of the wind. A second aspect...

  Pełny tekst do pobrania w portalu

• Methods and Instruments | Scanning Electrochemical Microscopy

  Publikacja

  • G. Wittstock
  • M. Muhle
  • M. Wilamowska-Zawłocka

  - Rok 2025

  Scanning electrochemical microscopy is based on the recording of electrolysis currents (Faradaic currents) at a microelectrode (ME) probe that is scanned over the sample. Different working modes are available to couple the electrolysis at the ME to reactions at the sample. The article explains their principles and provides examples of their application. The feedback mode, the sample-generation/tip collection mode, the redox-competition...

  Pełny tekst do pobrania w serwisie zewnętrznym

• Determination of pseudocapacitance chan ges of nickel oxide NiO electrode with use of dynamic electrochemical impedancje spectroscopy

  Publikacja

  • P. Ślepski
  • K. Darowicki
  • K. Andrearczyk
  • A. Sierczyńska

  - International Journal of Electrochemical Science - Rok 2014

  The electrochemical capacitors (ECs) are attractive energy storage devices which can be applied in many electronic products (e.g., cameras, laptops, cell phones) or hybrid electric vehicles (HEV). The energy storage in ECs is based on capacitive (the electrical double layer charging/discharging) and pseudocapacitive (additional charge provided by faradic reaction) phenomena. Considering the electrodes exhibiting pseudocapacitance,...

  Pełny tekst do pobrania w portalu

• Atmospheric deposition of microplastics in the coastal zone: Characteristics and relationship with meteorological factors

  Publikacja

  • K. Szewc
  • B. Graca
  • A. Dołęga

  - SCIENCE OF THE TOTAL ENVIRONMENT - Rok 2021

  The quantitative and qualitative compositions of microplastics (MPs) deposited from the atmosphere in the coastal zone were analysed. Moreover, links between MP deposition and meteorological factors (air humidity, wind speed, precipitation height, and air mass trajectories) were investigated

  Pełny tekst do pobrania w serwisie zewnętrznym

• Effects of electrophoretic deposition times and nanotubular oxide surfaces on properties of the nanohydroxyapatite/nanocopper coating on the Ti13Zr13Nb alloy

  Publikacja

  • M. Bartmański
  • A. Zieliński
  • M. Jażdżewska
  • J. Głodowska
  • P. Kalka

  - CERAMICS INTERNATIONAL - Rok 2019

  Load-bearing implants are developed with a particular emphasis placed on an application of ceramic hydroxyapatite coatings in order, to enhance the bioactivity of titanium implants and to shorten the healing time. Therefore, thin, fully crystalline coatings that are, highly adhesive, hydrophilic and demonstrating antibacterial properties are ly looked for. The aim of this research was to develop and characterize the properties...

  Pełny tekst do pobrania w serwisie zewnętrznym

• Method and Theory in the Study of Religion

  Czasopisma

  ISSN: 0943-3058 , eISSN: 1570-0682

• JOURNAL OF ARCHAEOLOGICAL METHOD AND THEORY

  Czasopisma

  ISSN: 1072-5369 , eISSN: 1573-7764

• Structural and mechanical properties of hydroxyapatite coatings formed by ion-beam assisted deposition

  Publikacja

  • A. Zykova
  • V. Safanov
  • S. Dudin
  • S. Yakovin
  • N. Donkov
  • M. H. Ghaemi
  • M. Szkodo
  • M. Antoszkiewicz
  • M. Szyfelbain
  • A. Czaban

  - Journal of Physics : Conference Series - Rok 2018

  The ion-beam assisted deposition (IBAD) is an advanced method capable of producing crystalline coatings at low temperatures. We determined the characteristics of hydroxyapatite Ca10(PO4)6(OH)2 target and coatings formed by IBAD using X-ray photoemission spectroscopy (XPS), X-ray diffraction (XRD), scanning electron microscopy (SEM), atomic force microscopy (AFM) and energy dispersive X-ray (EDX). The composition of the coatings'...

  Pełny tekst do pobrania w portalu

• Investigation of the electrochemical behaviour of AA1050 aluminium alloy in aqueous alkaline solutions using Dynamic Electrochemical Impedance Spectroscopy

  Publikacja

  • J. Wysocka
  • S. Krakowiak
  • J. Ryl
  • K. Darowicki

  - JOURNAL OF ELECTROANALYTICAL CHEMISTRY - Rok 2016

  The paper presents the electrochemical behaviour of aluminium alloy AA1050 in aqueous alkaline media in the pH range 14–8.5. Electrochemical study was applied in order to obtain comprehensive information on the mechanism and kinetics of the process of anodic dissolution of aluminium, supplemented by monitoring of surface topography using an electron microscope. The corrosion rate of AA1050 increases with increasing concentration...

  Pełny tekst do pobrania w serwisie zewnętrznym

• Study of Direct Methanol Fuel Cell Process Dynamics Using Dynamic Electrochemical Impedance Spectroscopy

  Publikacja

  • K. Darowicki
  • E. Janicka
  • P. Ślepski

  - International Journal of Electrochemical Science - Rok 2012

  A new technique, which was developed to characterize the direct methanol fuel cell under work conditions, has been presented in this paper. The impedance measurements were made using dynamic electrochemical impedance spectroscopy research technique in the galvanostatic mode, using multiple sinusoidal excitation. Obtained results show, that together with an increase of the temperature and working load, the global impedance...

  Pełny tekst do pobrania w portalu

• Suspension and process parameters selection for electrophoretic deposition of Mn–Co spinel coating on steel interconnects

  Publikacja

  • O. Ekhlasiosgouei
  • F. Smeacetto
  • S. Molin

  - INTERNATIONAL JOURNAL OF HYDROGEN ENERGY - Rok 2024

  Metallic interconnect coatings, consisting of MnCo2O4 spinel, were effectively applied to Crofer 22 APU using the electrophoretic deposition (EPD) method in both H2O: ethanol and pure ethanol solvents. The primary goal of this method was to prevent chromium migration, minimize evaporation, and control the oxidation rate. The study aimed to assess the quality, adhesion, and thickness of the Mn–Co coating, with the objective of...

  Pełny tekst do pobrania w serwisie zewnętrznym

• Additive Effect of Bromides and Chlorides on the Performance of Perovskite Solar Cells Fabricated via Sequential Deposition

  Publikacja

  • J. Szmytkowski
  • D. Głowienka
  • M. Verger
  • H. Gorter
  • I. Dogan
  • W. Verhees
  • M. Najafi
  • S. Veenstra
  • Y. Galagan

  - JOURNAL OF POWER SOURCES - Rok 2021

  A two-step sequential deposition method has been applied to prepare the solar cells with two types of perovskites Cs0.15FA0.85Pb(I0.95Cl0.05)3 and Cs0.15FA0.85Pb(I0.95Br0.05)3. In order to obtain the perovskite layers, the different sources of bromine and chlorine atoms were used for synthesis. The performance and time stability of chloride-based photocells are worse in comparison to the bromide-based devices. It can be explained...

  Pełny tekst do pobrania w portalu

• Evaluation of Temperature Influence on Electrochemical Processes Occurring in a Lithium-Ion Supercapacitor with the Use of Dynamic Electrochemical Impedance Spectroscopy

  Publikacja

  • M. Mielniczek
  • E. Janicka
  • Ł. Gaweł
  • K. Darowicki

  - ENERGIES - Rok 2021

  In order to obtain the full impedance characteristics of a lithium-ion capacitor as a function of temperature, the authors proposed the use of dynamic electrochemical impedance spectroscopy. Impedance tests were carried out under wide range of dynamic temperature changes for lithium-ion supercapacitors. Significant differences in electrochemical processes were observed as a result of working temperature. Moreover, the quality of...

  Pełny tekst do pobrania w portalu

• Carbon Deposition and Sulfur Poisoning in SrFe0.75Mo0.25O3-δand SrFe0.5Mn0.25Mo0.25O3-δElectrode Materials for Symmetrical SOFCs

  Publikacja

  • K. Zheng
  • K. Świerczek
  • J. Polfus
  • M. Sunding
  • M. Pishahang
  • T. Norby

  - Journal of The Electrochemical Society - Rok 2015

  Pełny tekst do pobrania w serwisie zewnętrznym

• Simultaneous opto-electrochemical monitoring of carbamazepine and its electro-oxidation by-products in wastewater

  Publikacja

  • M. Pierpaoli
  • A. D. Dettlaff
  • M. Szopińska
  • K. Karpienko
  • M. Wróbel
  • A. Łuczkiewicz
  • S. Fudala-Książek
  • R. Bogdanowicz

  - JOURNAL OF HAZARDOUS MATERIALS - Rok 2021

  The growing human impact on aquatic environments, due to the extensive use of pharmaceuticals and the release of persistent pollutants, makes it necessary to implement new widespread methods for the characterisation and quantification of such contaminants and relative degradation products. Carbamazepine, 5H-dibenzo[b,f]azepine-5-carboxamide, (CBZ) is a widely used anti-epileptic drug, characterised by its limited removal by conventional...

  Pełny tekst do pobrania w portalu

• Properties of Barium Cerate Thin Films Formed Using E-Beam Deposition

  Publikacja

  • M. S. Campos Covarrubias
  • M. Sriubas
  • K. Bockute
  • P. Winiarz
  • T. Miruszewski
  • W. Skubida
  • D. Jaworski
  • M. Bartmański
  • M. Szkodo
  • M. Gazda
  • G. Laukaitis

  - Crystals - Rok 2020

  This article focuses on the properties of the BaCeO3 thin films formed by electron-beam vapor deposition and investigates the formation of barium cerates on supports with different thermal expansion coefficients (Stainless Steel, Invar, Glass Sealing, and Inconel substrates) and the influence of the technological parameters on the properties of the formed thin films with an emphasis on the stability of the films. Morphology and...

  Pełny tekst do pobrania w portalu

• Substrate characterization in a electrochemically derived Manganium-Cobaltium thin films

  Dane Badawcze

  open access

  • M. Łapiński

  Manganium-Cobaltium thin films were electrochemically deposited on a Ni foams subsrates in a one-step process at −1.1 V vs. Ag/AgCl in an aqueous solution of differently concentrated Mn(NO3)2·4H2O and Co(NO3)2·6H2O with the deposition time limited by charges of 60, 120, and 200 mC at 25 °C. The concentration ratios of Mn(NO3)2·4H2O to Co(NO3)2·6H2O...

• Raman data of deuterium and hydrogen grown boron-doped diamond

  Dane Badawcze

  wersja 1.0 open access

  • R. Bogdanowicz
  • M. Sobaszek

  Raman spectra were recorded at room temperature using a micro-Raman spectrometer (Invia, Renishaw) equipped with an edge filter with different excitation wavelengths and lasers: UV λ = 325 nm (HeCd), blue λ = 488 nm (Ar+), green λ = 514 nm (Ar+), and IR λ = 785 nm (IR diode) and 50× microscope objective. To avoid sample heating, the radiation power...

• Anomalous anisotropy of deuterium-grown boron-doped diamond and the role of boron-tetramers in the Mott-Insulator transition

  Dane Badawcze

  open access

  • M. Sobaszek
  • S. Kwon
  • M. Winiarski
  • B. Rutkowski
  • J. Ryl
  • D. Wang
  • X. Li
  • M. Bockrath
  • W. Goddard III

  We show anisotropy in the superconductivity for boron-doped diamond thin films prepared with Microwave Plasma Assisted Chemical Vapor Deposition using deuterium-rich plasma. This anomalous phase transition is linked with the emergence of boson quantum entanglement states behaving as a bosonic insulating state. Here, we show that the superconducting...

• Local electrochemical impedance spectroscopy in dynamic mode of galvanic coupling

  Publikacja

  • Ł. Burczyk
  • K. Darowicki

  - ELECTROCHIMICA ACTA - Rok 2018

  A novel method that combines local electrochemical impedance spectroscopy and mapping in dynamicmode is proposed. Method was validated over two galvanic couplings, namely zinc/copper and cad-mium/copper. Impedance spectrum response for all measuring points was obtained by means ofsimultaneous implementation of selected range of frequencies. Proposed method allows the measure-ment in a more time-efficient manner, at the same time...

  Pełny tekst do pobrania w serwisie zewnętrznym

• Electrochemical Society Interface

  Czasopisma

  ISSN: 1064-8208 , eISSN: 1944-8783

• Electrochemical Energy Reviews

  Czasopisma

  ISSN: 2520-8489 , eISSN: 2520-8136

• Properties of Nanohydroxyapatite Coatings Doped with Nanocopper, Obtained by Electrophoretic Deposition on Ti13Zr13Nb Alloy

  Publikacja

  • M. Bartmański
  • Ł. Pawłowski
  • G. Strugała
  • A. D. Mielewczyk-Gryń
  • A. Zieliński

  - Materials - Rok 2019

  Nowadays, hydroxyapatite coatings are the most common surface modification of long-term implants. These coatings are characterized by high thickness and poor adhesion to the metallic substrate. The present research is aimed at characterizing the properties of nanohydroxyapatite (nanoHAp) with the addition of copper nanoparticle (nanoCu) coatings deposited on the Ti13Zr13Nb alloy by an electrophoresis process. The deposition of...

  Pełny tekst do pobrania w portalu

• 2D MXene nanocomposites: electrochemical and biomedical applications

  Publikacja

  • M. Ramezani Farani
  • B. Nourmohammadi Khiarak
  • R. Tao
  • Z. Wang
  • S. Ahmadi
  • M. Hassanpour
  • M. Rabiee
  • M. Saeb
  • E. C. Lima
  • N. Rabiee

  - Environmental Science-Nano - Rok 2022

  In recent years, key questions about the interaction of 2D MXene nanomaterials in electrochemical and biomedical applications have been raised. Most research has focused on clarifying the exclusive properties of the materials; however, only limited reports have described the biomedical applications of 2D nanomaterials. 2D MXenes are monolayer atomic nanosheets resulting from MAX phase ceramics. The hydrophilic properties, metallic...

  Pełny tekst do pobrania w serwisie zewnętrznym

• In-situ Cu-doped MnCo-spinel coatings for solid oxide cell interconnects processed by electrophoretic deposition

  Publikacja

  • A. Sabato
  • S. Molin
  • H. Javed
  • E. Zanchi
  • A. Boccaccini
  • F. Smeacetto

  - CERAMICS INTERNATIONAL - Rok 2019

  The Cu doping of the Mn–Co spinel is obtained “in-situ” by electrophoretic co-deposition of CuO and Mn1.5Co1.5O4 powders and subsequent two-step reactive sintering. Cu-doped Mn1.5Co1.5O4 coatings on Crofer22APU processed by electrophoretic co-deposition method are tested in terms of long term oxidation resistance and area specific resistance tests up to 3600 h. The introduction of Cu in the spinel lead to higher level of densification...

  Pełny tekst do pobrania w serwisie zewnętrznym