Wyszukiwarka
Filtry
wszystkich: 48
Wyniki wyszukiwania dla: SOLAR RADIATION
-
Risk of power cables insulation failure due to the thermal effect of solar radiation
PublikacjaLow-voltage, as well as high-voltage power cable lines, are usually buried in the ground. The ampacity of the power cables in the ground mainly depends on the thermal resistivity of the soil, which may vary in a wide range. A common practice in power cable systems performance is to supply them from a pole of an overhead line. If so, a section of the line is located in free air and can be directly exposed to solar radiation. In...
-
Design of power cable lines partially exposed to direct solar radiation – special aspects
PublikacjaPower cable lines are usually buried in the ground. However, in some cases, their ending sections are mounted along the supports of overhead lines. This leads to a situation where the cables are exposed to direct solar radiation and, consequentially, overheat. The paper presents the advanced computer modelling of power cables’ heating, considering their insolation as well as the effect of wind. The temperature and current-carrying...
-
Overheating of underground power cable line due to its partial exposition to solar radiation
PublikacjaCurrent-carrying capacity of underground power cable lines depends, among others, on thermal resistivity of the soil and cables layout: trefoil formation, flat formation with or without spacing. If conditions for heat transfer in the ground are favorable, the current-carrying capacity is relatively high. Therefore, it generates risk of the power cables overheating, if part of the cable line is located vertically in the air, to...
-
Ampacity of power cables exposed to solar radiation – recommendations of standards vs. CFD simulations
PublikacjaThe aim of the paper is to evaluate the ampacity of a low-voltage single power cable according to: 1) recommendations of the standard IEC 60287, 2) a Computational Fluid Dynamics method, implemented in Ansys software; and comparison of the results obtained for these two cases. Moreover, limitations of recommendations of the above mentioned standard are indicated.
-
Effect of solar radiation on current-carrying capacity of PVC-insulated power cables – the numerical point of view
PublikacjaPower cables are usually buried in the soil, which results in their relatively high current-carrying capacity. However, there are cases in which the starting/final section of a cable line runs along a pole of an overhead power line. Power cables can be directly exposed to solar radiation then, and this negatively influences their current-carrying capacity as well as estimated life of the cables’ insulation. An analysis of thermal...
-
Wind speed, wind direction and solar radiation datasets; wind and solar energy resources analysis
Dane BadawczeDataset contain the results of wind speed, wind direction and solar radiation for wind and solar energy resources analysis performed in years 2008 and 2009. Application for efficiency and profitability of solar and wind power plants anaylsis and for energy generation forecasting algorithms design and anaysis. Datasets used in doctoral dissertations,...
-
Solar radiation (PAR, UV-B and UV-A) reaching the sea surface - Gdańsk Deep (2001-2005)
Dane BadawczeSolar radiation reaching the sea surface was measured in spring (2001, 2003, 2005) and autumn (2002, 2004). For measurements of the photosynthetic active radiation - PAR (400-700 nm), the Ejkelkamp SKP 210 / I 0896 13595 sensor was used, the UV-B radiation (280-315 nm) was measured with the Ejkelkamp SKU 430 0497 14854 sensor, while UV-A (315- 380 nm)...
-
Iron-based catalysts under solar and visible radiation for contaminants of emerging concern removal
Publikacja -
Alternative Energy: Photovoltaic Solar Cells
PublikacjaSolar radiation is a fuel for photovoltaic cells and modules, which are a source of electric energy. Viable solar technologies that have been developed in the past are starting to be adopted on a broader and more meaningful global scale across different sectors with ever-increasing market penetration. In this entry, a brief overview of the material properties relevant to solar cell operation, the structure of the solar cell, and electrical...
-
An analysis of solar energy conversion systems based on photon and thermal processes
PublikacjaSolar spectral irradiance covers a fairly broad wavelength range. Solar radiation is part of the electromagnetic spectrum which is described by the concept of wave-particle duality. The corpuscular theory of electromagnetic radiation states that energy is transmitted by photons. Photons carry specific amounts of energy which can be used to convert solar energy into other types of energy, in particular electricity. The internal...
-
Photocatalysts for Solar Energy Conversion
PublikacjaPhotocatalytic oxidation over suspended solid photocatalysts (e.g., titanium dioxide) has been proposed as a sustainable process for treatment and purification of water and wastewater as well as the process for photoconversion of solar energy to hydrogen, methane, and other low hydrocarbons. Solar radiation could be used to drive heterogeneous electrochemical reactions at the surface of an optically active photocatalyst (e.g.,...
-
Performance of the flat plate solar collector operated with water-Al2O3 nanofluid
PublikacjaThe paper discusses the effect of application of water-Al2O3 nanofluid, as a working fluid, on the efficiency of a flat plate solar collector. The mass concentration of nanoparticles was 0.1%, 0.2% and 0.4%. The tests were conducted for two values of radiation of about 1050 W/m2 and 400 W/m2, and volume flow rates of 60 l/h, 120 l/h and 170 l/h. The efficiency was calculated according to recommendations of the Polish Standard....
-
Performance of the flat plate solar collector operated with water-Al2O3 nanofluid
PublikacjaThis paper shows the experimental results of the performance a flat plate solar collector with water-Al2O3 nanofluid as a working fluid. The weight fractions of nanoparticles were 0.1%, 0.2% and 0.4%. The volume flow rate of nanofluid varied from 60 l/h to 170 l/h. The results show that application of nanofluids instead of pure water resulted in higher efficiency of the tested flat plate solar collector for given range of thermal...
-
Ocena warunków nasłonecznienia i projektowanie elektrowni słonecznych z wykorzystaniem dedykowanego oprogramowania oraz baz danych
PublikacjaPrzytoczono typowe dla obszaru Polski wartości nasłonecznienia. Zaprezentowano sposoby dokładniejszego określenia wartości nasłonecznienia w oparciu o bazy danych o nasłonecznieniu i aplikacje komputerowe. Narzędzia te pozwalają w pełniejszy sposób uwzględnić kąt nachylenia i azymut modułów fotowoltaicznych, linię horyzontu i zacienienie oraz zmienność nasłonecznienia w ciągu roku na podstawie statystycznych wartości nasłonecznia...
-
Potential Application of Solar Energy Systems for Electrified Urban Transportation Systems
PublikacjaThe paper presents a novel approach toward the use of solar energy systems in public transportation. The concept of energy generation in PV systems for supplying a trolleybus transportation system is proposed for the city of Gdynia (Poland). The suggested way of energy production allows reducing the environmental harm impact of the municipal transportation system. Moreover, the proposed way of green energy use can be a more profitable...
-
ENVIRONMENTAL ASSESSMENT OF SOLAR CELL MATERIALS
PublikacjaIn today’s world, fossil fuels, including coal, oil, and gas, are the primary energy sources from which electricity is obtained. As they are exhaustible and their exploitation has a negative impact on the natural environment, they should be, at least partially, replaced by renewable energy sources. One of these sources is solar energy. The use of solar energy releases no CO2, SO2, or NO2 gases, and does not contribute to global...
-
Heat recovery from the hybrid photovoltaic tile – experimental studies with the solar light simulator
PublikacjaConsidering the current development of micro-cogeneration energy sources, supported by the national prosumer policy and the act on the renewable energy sources, there is a great demand for the effective solar technologies. In this area, the photovoltaic cells with a combined conversion of the solar radiation energy into the electrical and thermal energy (PV/T cells) seem to be attractive. They are already widely available and treated...
-
Applying response surface method to optimize the performance of a divergent-chimney solar power plant
PublikacjaOne of the effective tools to generate electricity from solar energy is Divergent-chimney solar power plant (DSPP). Divergent and cylindrical chimneys of solar power plants have different performances considering turbine pressure drop ratio (ft). For the first time, the divergent angle (DA) and solar radiation (SR) interaction effects on 〖ft〗_opt are discussed through applying the Computational Fluid Dynamics (CFD) and Response...
-
Shading, Dusting and Incorrect Positioning of Photovoltaic Modules as Important Factors in Performance Reduction
PublikacjaThe amount of solar radiation reaching the front cover of a photovoltaic module is crucial for its performance. A number of factors must be taken into account at the design stage of the solar installation, which will ensure maximum utilization of the potential arising from the location. During the operation of a photovoltaic installation, it is necessary to limit the shading of the modules caused by both dust and shadowing by trees...
-
POSSIBILITIES OF ELECTRICAL ENERGY GENERATION IN PHOTOVOLTAIC SYSTEMS INSTALLED IN CENTRAL EUROPE
PublikacjaNowadays, fossil fuels are the main sources of energy from which electricity is obtained. But these sources will not last forever, so in due course renewable energies will have to replace them in this role. One of these new sources is solar energy. To generate electricity from sunlight, solar (photovoltaic - PV) cells and modules are used. The increasing interest in PV cells and modules worldwide is due mainly to the fact that...
-
g-C3N4 for Photocatalytic Degradation of Parabens: Precursors Influence, the Radiation Source and Simultaneous Ozonation Evaluation
PublikacjaGraphitic carbon nitride (g-C3N4) is a promising catalyst for contaminants of emerging concern removal applications, especially as a visible-light-driven material. In this study, g-C3N4 catalysts were effectively synthesized through a simple thermal polymerization method, using melamine, urea, and thiourea as precursors to elucidate the influence of these compounds on the final product’s photocatalytic performance. The degradation...
-
The role of noble metals in TiO2 nanotubes for the abatement of parabens by photocatalysis, catalytic and photocatalytic ozonation
PublikacjaThe role of modified TiO2 nanotubes (TNTs) with noble metals was studied for photocatalysis, catalytic and photocatalytic ozonation of a paraben’s mixture. The TNTs were obtained by anodization and were modified by photodeposition with 0.25 mol% of Au, Pt or Pd. Results showed that solar photocatalysis led to higher degradation than UVA radiation, and under UVA radiation, the use of 3 Pt-TNTs (3 TNTs plates modified with Pt) and...
-
Trees as a solar control measure for southern-oriented street frontages. Analysis of a selected street model for a humid continental climate
PublikacjaThe present study is aimed at the analysis of possibilities for shading southern frontage of street oriented along the E-W axis by the single row of trees, parallel to the southern elevations. The effectiveness of solar control shading was tested depending on the geometric relationships between trees and buildings. Numerical simulation analyses were conducted in Rhinoceros® program for the street located in humid continental climate...
-
The Environmental Benefits of Photovoltaic Systems: The Impact on the Environment in the Production of Photovoltaic Systems: With a Focus on Metal Recovery
PublikacjaGreenhouse gases (GHGs) such as carbon dioxide, nitrous oxide and methane, trap heat and energy, thus preventing solar radiation from escaping back into space. As the quantity of greenhouse gases in the atmosphere increases so does the trapped heat and corresponding global temperature. As a result, storms become more violent, droughts more prevalent, glaciers melt, and sea levels rise, to name but a few effects of a rapidly changing...
-
Insightful studies of AuCu nanostructures deposited on Ti platform: Effect of rapid thermal annealing on photoelectrochemical activity supported by synchrotron radiation studies
PublikacjaIn this work, we present the influence of annealing atmospheres during rapid thermal annealing (40◦C/s) on nanostructured Ti platforms modified by 10 nm layer of AuCu alloy obtained via magnetron sputtering. The AuCu/Ti platform annealed under hydrogen atmosphere exhibits the best photoelectrochemical activity under visible light, i.e. 27 times higher photocurrent than for pure Ti dimpled platform, and the lowest reflectance with minimum...
-
Photovoltaic-Installation Performance in Central Europe on the Example of Poland
PublikacjaThe amount of the electric energy obtained from a photovoltaic (PV) installation depends on the energy of the radiation. Weather conditions differ strongly between various years even in the same season. Depending on the climatic conditions of a given location, fixed PV solar plants as well as one-axis and dual-axis tracking PV solar plants are being installed worldwide. The aim of this work is to analyse the sunlight intensity...
-
The Issue of Shading Photovoltaic Installation Caused by Dust Accumulation on the Glass Surface
PublikacjaThe issue of accumulation of dust and other pollutants on the surface of photovoltaic modules was thoroughly analysed over the years. One of the first surveys in this field of knowledge linked pollutant accumulation on the module surface with transmittance loss of its glass covering, which leads to lessened amount of solar radiation reaching solar cells. First stage of this accumulation process is linear transparency loss, and second...
-
CFD-based evaluation of current-carrying capacity of power cables installed in free air
PublikacjaEvaluation of current-carrying capacity of power cables and selection of cross-sectional area of their conductors are mainly performed in accordance with requirements of EN, IEC or IEEE standards. However, these standards do not provide all methods of cables installation and location which occur in practice. Thus, in some cases, performance of advanced modeling of various thermal phenomena, affecting power cables current-carrying...
-
Thermal cooling process by nanofluid flowing near stagnating point of expanding surface under induced magnetism force: A computational case study
PublikacjaThis paper is dedicated to the exam of entropy age and research of the effect of mixing nanosolid additives over an extending sheet. In this review, Newtonian nanofluid version turned into researched at the actuated appealing field, heat radiation and variable heat conductivity results. With becoming modifications, the proven PDEs are moved into popular differential situations and paintings mathematically making use of a specific...
-
Evaluation of fire hazard in electrical installations due to unfavorable ambient thermal conditions
PublikacjaEvaluation of fire hazard caused by electrical installations is a difficult and important topic, and it limits the possibility of loss of life or health of people, as well as the occurrence of significant property damage. In particular, this hazard was caused by power cables and especially photovoltaic (PV) installations. The authors proved that power cables directly exposed to strong solar radiation are likely to exceed maximum...
-
The use of lightweight aggregate saturated with PCM as a temperature stabilizing material for road surfaces.
PublikacjaThis paper presents the possibility of adding lightweight building aggregates to increase the stability – mechanical as well as thermal - of constructions and road objects. This stability can be achieved through saturating the porous granules of aggregate with a phase-change material (PCM) that allows the accumulation of solar heat. Intense solar radiation, especially during the summer, can cause the asphalt on road surfaces, bridges...
-
The influence of meteorological conditions and anthropogenic activities on the seasonal fluctuations of BTEX in the urban air of the Hanseatic city of Gdansk, Poland
PublikacjaThe results of studies conducted in Gdansk in the period from January to December 2013 and focused on the determination of BTEX in the atmospheric air are presented. At the stage of the isolation and/or enrichment of analytes from the gaseous medium, a passive sampling technique—Radiello® diffusive passive samplers, was applied. The time-weighted average annual concentration of benzene, toluene, ethylbenzene, and total xylenes...
-
Spectacular Oxygen Evolution Reaction Enhancement Through Laser Processing of the Nickel-Decorated Titania Nanotubes
PublikacjaThe selective, laser-induced modification of the nickel-decorated titania nanotubes provides remarkable enhancement toward oxygen evolution reaction. Particularly, the irradiation of the laterally spaced crystalline TiO2 nanotubes, results in the formation of the tight closure over irradiated end, preserving their hollow interior. The shape of the absorbance spectra is modulated along with applied energy, and the new absorption...
-
Spectacular Oxygen Evolution Reaction Enhancement through Laser Processing of the Nickel‐Decorated Titania Nanotubes
PublikacjaThe selective, laser‐induced modification of the nickel‐decorated titania nanotubes provides remarkable enhancement toward oxygen evolution reaction. Particularly, the irradiation of the laterally spaced crystalline TiO2 nanotubes, results in the formation of the tight closure over irradiated end, preserving their hollow interior. The shape of the absorbance spectra is modulated along with applied energy, and the new absorption...
-
Comparison of Absorbed and Intercepted Fractions of PAR for Individual Trees Based on Radiative Transfer Model Simulations
PublikacjaThe fraction of absorbed photosynthetically active radiation (fAPAR) is a key parameter for estimating the gross primary production (GPP) of trees. For continuous, dense forest canopies, fAPAR, is often equated with the intercepted fraction, fIPAR. This assumption is not valid for individual trees in urban environments or parkland settings where the canopy is sparse and there are well-defined tree crown boundaries. Here, the distinction...
-
Valorization of waste cabbage leaves by postharvest photochemical treatments monitored with a non-destructive fluorescence-based sensor
PublikacjaThe biosynthesis of polyphenolic compounds in cabbage waste, outer green leaves of white head cabbage (Brassica oleracea L. var. capitata subvar. alba), was stimulated by postharvest irradiation with UVB lamps or sunlight. Both treatments boosted the content of kaempferol and quercetin glycosides, especially in the basal leaf zone, as determined by the HPLC analysis of leaf extracts and by a non-destructive optical sensor. The...
-
Enhanced Photoelectrocatalytical Performance of Inorganic-Inorganic Hybrid Consisting BiVO4, V2O5, and Cobalt Hexacyanocobaltate as a Perspective Photoanode for Water Splitting
PublikacjaThin layers of BiVO4/V2O5 were prepared on FTO substrates using pulsed laser deposition technique. The method of cobalt hexacyanocobaltate (Cohcc) synthesis on the BiVO4/V2O5 photoanodes consists of cobalt deposition followed by electrochemical oxidation of metallic Co in K3[Co(CN)6] aqueous electrolyte. The modified electrodes were tested as photoanodes for water oxidation under simulated sunlight irradiation. Deposited films...
-
Stannates, titanates and tantalates modified with carbon and graphene quantum dots for enhancement of visible-light photocatalytic activity
PublikacjaMost efforts in heterogeneous photocatalysis are focused on development of new and stable photoactive materials efficient in degradation of various pollutants under visible-light irradiation. In this regard, the wide-bandgap perovskite semiconductors, i.e., SrTiO3 (titanate), SrSnO3 (stannate) and AgTaO3 (tantalate), were prepared by a solvothermal method, and then modified with carbon quantum dots (CQDs) or graphene quantum dots...
-
Development of novel (BiO)2OHCl/BiOBr enriched with boron doped-carbon nanowalls for photocatalytic cytostatic drug degradation: Assessing photocatalytic process utilization in environmental condition
PublikacjaIn this work, a series of novel (BiO)2OHCl/BiOBr-x%B:DGNW (x = 0%, 1%, 1.5%, 2%) composites with different content of boron-doped diamond/graphene nanowalls (B:DGNW) were fabricated by simple solvothermal synthesis. A boron-doped diamond/graphene nanowalls (B:DGNW) were prepared by CVD method. A series of analyses: XRD, XPS, SEM, and TEM showed that the photocatalyst (BiO)2OHCl/BiOBr-x%B:DGNW with a “flower-like” morphology was...
-
Phototransformation of Amlodipine: Degradation Kinetics and Identification of Its Photoproducts
PublikacjaNowadays, monitoring focuses on the primary compounds and does not include degradation products formed during various biological and chemical processes. Transformation products may have the same effects to human health and the environment or sometimes they can be more toxic than the parent compound. Unfortunately, knowledge about the formation of degradation products is still limited, however, can be very important for the environmental...
-
Protect our right to light
Publikacja“The struggle for light” is how the Swiss architect Le Corbusier described the history of architecture in 1935. Today, with the skies crowded out by buildings in modern cities, those words should ring in the ears of policymakers and planners. Skyscraper construction is booming. China is the leader, last year completing 88 of the 143 buildings around the world that are taller than 200 metres (see ‘Vertical growth’). As the nation’s...
-
NEW SOLUTIONS FOR THE SOLAR CHARGE CONTROLLERS DESIGN FOR OBTAINING TRUE MPP IN PARTLY SHADED PV MODULES
PublikacjaSoft shading sources such as tree limbs, structural elements of buildings and chimneys, scatter and refract sunlight, significantly reducing the amount of radiation reaching the surface of the module. The hard shadings located directly on the surface (i.e. bird droppings, leaves, snow) tend to stop sunlight completely. These phenomena significantly affects the output characteristics of photovoltaic modules and often contribute...
-
Review of Recent Advancement on Nature/Bio-inspired Antenna Designs
PublikacjaThis article presents an extensive examination of antennas rooted in nature and biology, showcasing their remarkable performance across a wide spectrum of frequencies—from microwave to terahertz. The limitations of traditional antenna design have become increasingly evident in the face of burgeoning demands for novel communication technologies. Conventional analytical-equation-based approaches struggle to deliver the combined performance...
-
Long-term measurements from a photovoltaic power plant and meteorological stations at the Laboratory LINTE^2 of Gdańsk University of Technology
Dane Badawcze1) The Laboratory LINTE^2 is a large research infrastructure operated by the Faculty of Electrical and Control Engineering at Gdańsk University of Technology, to be found in Gdańsk, Poland (54.3690 N, 18.6130 E). 2) The measurements have been collected from a photovoltaic power plant located on the roof of the laboratory, having total capacity...
-
Possibilities and benefits of a new method of modifying conventional building materials with phase-change materials (PCMs)
PublikacjaThe paper presents a current study devoted to the optimization of the amount of PCM present within traditional building materials, utilized in this case in hollow-brick walls. Authors focus on proposing an alternative to typical direct addition of PCM to existing building materials: introducing two- and three-component mixtures, based on a porous PCM carrier, which in this case was construction aggregate. Preliminary studies of...
-
Survey on opportunities and barriers in lighting controls
PublikacjaThis report summarizes a survey performed in eight countries on the status quo of daylight and electric lighting control systems. Feedback from more than 100 international experts (building / facility managers and planers) was evaluated. The aim of the survey was to identify the perception of the different possibilities of the current lighting control solutions and the expectations about the control systems. The survey aims to...
-
Effect of synthesis method parameters on properties and photoelectrocatalytic activity under solar irradiation of TiO2 nanotubes decorated with CdS quantum dots
PublikacjaThe growing research interest on photoelectrocatalysis has encouraged the search for new materials with high activity and the development of methods for their synthesis. The successive ionic layer adsorption and reaction (SILAR) method is an effective way to synthesize materials with photoelectrocatalytic (PEC) properties that are active under visible radiation. Therefore, studies on the impact of the parameters of the SILAR method...
-
Nanoparticles preparation using microemulsion systems
PublikacjaMetallic nanoparticles become of current interests because they exhibit unique properties compared with those of metal atoms or bulk metal due to the quantum size effect and their large surface area, which make them attractive for applications in optics, electronics, catalysis biology and medicine. TiO2 has been used for environmental remediation purposes such as in the purification of water and air and also solar-to chemical energy...