Wyszukiwarka
Filtry
wszystkich: 1459
-
Katalog
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: POLYMERIC BRUSH
-
Dielectric Properties of BiNbO<sub>4</sub>-Based Ceramic-Polymer Composites with 0-3 Connectivity
PublikacjaIn the present study two-phase BiNbO4//PVDF composites with 0-3 connectivity were studied by impedance spectroscopy within the frequency range Δν=100Hz-1MHz at room temperature. Polyvinylidene fluoride (PVDF) acted as a matrix whereas bismuth niobate (BiNbO4) powder acted as a dispersed phase. The volume fraction of the ceramic phase was cV=2, 4, 6, 8, 10, 16 and 20vol%. Analysis of the impedance data registered for composites...
-
The influence of polymer bearing material and lubricating grooves layout on wear of journal bearings lubricated with contaminated water
PublikacjaThe goal of the present paper is to investigate wear properties of journal sliding bearing operating in the conditions of contaminated water lubrication. Several bearing materials and bearing sleeve designs (differing in the axial grooves position and their shape) were tested experimentally under typical operating conditions in a dedicated test rig, which was equipped with a lubricating system, enabling lubrication with contaminated...
-
Application of Headspace Solid-phase Microextraction with Poly(1-vinyl-3- Hexylimidazolium Chloride) Polymeric Ionic Liquid Coating using GC - MS to Determine Volatile Fatty Acids in Dairy Wastewater
PublikacjaVolatile fatty acids were determined in this study using headspace solid-phase microextraction (HS-SPME) with a poly(1-vinyl-3-hexylimidazolium chloride) polymeric ionic liquid coated fiber followed by gas chromatography - mass spectrometry. Experimental parameters such as extraction time and temperature, sample volume as well as desorption time and temperature were optimized. Detection limits of the method were in the range of...
-
Absorption and fluorescence spectra of 1,8-diazafluoren-9-one (DFO) in PVA polymer for different concentrations
Dane BadawczeAbsorption and fluorescence spectra of 1,8-diazafluoren-9-one (DFO) in PVA film for different concentrations of dye.
-
Assessing ecotoxicity, synergic and antagonistic actions of commonly used components of polymerization mixture in molecularly imprinted polymers preparation process
PublikacjaIncreasingly, the challenge is the optimal process of developing a suitable MIP-type sorptive material (taking into account its final form and application area), which is mainly related to the efficiency/effectiveness of the polymerization process. The lack of reaction or its low efficiency generates additional waste and puts it into the environmental cycle. The main aim of the performed research was the estimation of ecotoxicity,...
-
Electrochemical synthesis of 2D copper coordination-polymers: Layer-stacking deviation induced by the solvent and its effect on the adsorptive properties
PublikacjaA 2D Cu-based Metal-Organic Framework (MOF), namely copper-terephthalate (Cu(1,4-BDC)), was successfully synthesized by electrochemical method for effective methylene blue (MB) sorption from aqueous solutions. The composition, morphology, and the presence of functional groups in the obtained material were verified by Fourier Transform Infrared spectroscopy (FTIR), Powder X-Ray Diffraction (PXRD), Thermal (TGA), and Elemental (EA)...
-
Lead(II) coordination polymers with imidazole-4- and pyrazole-3-carboxylate isomeric linkers: Structural diversity and luminescence properties
PublikacjaUsing 1H-imidazole-4-carboxylic acid (4imCOOH) and 1H-pyrazole-3-carboxylic acid (3pyrCOOH) coordination polymers [Pb(4imCOO)2(H2O)]n (1) and [Pb2(3pyrCOO)4]n (2) were constructed. Obtained polymers were characterized via FT-IR, X-ray, PL and TG methods. The coordination polyhedron around Pb(II) in 1 is described as distorted pentagonal pyramid with hemidirected coordination sphere (based on DFT calculations). Compound 2 consists...
-
Paulina Kosmela dr inż.
Osoby -
Tailoring of Optical Properties of Methacrylate Resins Enriched by HPHT Microdiamond Particles
PublikacjaDiamond particles have great potential to enhance the mechanical, optical, and thermal properties of diamond–polymer composites. However, the improved properties of diamond–polymer composites depend on the size, dispersibility, and concentration of diamond particles. In the present study, diamond–polymer composites were prepared by adding the microdiamond particles (MDPs) with different concentrations (0.2–1 wt.%) into polymers...
-
Application of g-C3N4/ZnO nanocomposites for fabrication of anti-fouling polymer membranes with dye and protein rejection superiority
PublikacjaPolysulfone (PSf) membranes are privileged for water and wastewater treatment, but because of their hydrophobic nature, they suffer from fouling, which lowers their performance and lifetime. In this work, g-C3N4 and g-C3N4/ZnO nanomaterials were synthesized via a hydrothermal method to modify the PSf membrane for effective dye separation and reduction of organic fouling. Since g-C3N4/ZnO possesses –OH and –NH reactive groups, g-C3N4/ZnO/PSf...
-
Multistep energy migration between 3,3'-diethyl-9-methylthiacarbocyanine iodide monomers in uniaxially oriented polymer films
PublikacjaWykonano pomiary obserwabli fluorescencyjnych dla wieloetapowego transferu energii w układzie zawierającym MDTCI (3,3'-diethyl-9-methylthiacarbocyanine iodide) w rozciąganych osiowo foliach polimerowych (PVA). Wyniki doświadczalne porównano z rezultatami symulacji Monte Carlo, stwierdzając ich bardzo dobrą zgodność. Ponadto z symulacji Monte Carlo otrzymano szereg informacji nie dających się zmierzyć doświadczalnie jak np. czas...
-
Characterization of structure and properties of polymer films made from blends of polyethylene with poly(4-methyl-1-pentene)
Publikacja -
Large deformations formulation and elastic instability of single layer nanoplate embedded on polymer medium in nonlocal continuum mechanic
Publikacja -
The Effect of Polymer Microstructure on Encapsulation Efficiency and Release Kinetics of Citropin 1.1 from the Poly(ε-caprolactone) Microparticles
Publikacja -
Application of g-C3N4/ZnO nanocomposites for fabrication of anti-fouling polymer membranes with dye and protein rejection superiority
Publikacja -
The Application of Polymer Inclusion Membranes for the Removal of Emerging Contaminants and Synthetic Dyes from Aqueous Solutions—A Mini Review
Publikacja -
Copper recovery from model chloride solution using polymer inclusion membranes with 1-decyl-2,4-dimethylimidazle
Publikacja -
The Influence of the Morphology and Mechanical Properties of Polymer Inclusion Membranes (PIMs) on Zinc Ion Separation from Aqueous Solutions
Publikacja -
MO‐F‐214‐06: Linear Energy Transfer Response of Polymer Gel Dosimeters in Therapeutic Proton Beams
Publikacja -
SU‐GG‐T‐270: Evaluation of a Novel 3‐D Polymer Gel Dosimetry System for Proton Radiotherapy
Publikacja -
SU-GG-T-267: Imaging Properties of the OCTOPUSTM-IQ Scanner in Combination with a New Polymer Gel Dosimeter
Publikacja -
Raman scattering measurements in monitoring of polymer synthesis process. Lightmetry 2002 : Metrology and Testing Techniques Using Light.
PublikacjaW artykule omówiono możliwości wykorzystania pomiarów ramanowskich do monitorowania w czasie rzeczywistym przebiegu procesów syntezy materiałów polimerowych. Wykorzystano sondy światłowodowe do sprzęgnięcia aparatury pomiarowej z typowym stanowiskiem technologicznym. Pomiary miały charakter zdalny, nieniszczący i niezakłócający przebieg reakcji.
-
The electrochemical impedance spectroscopy studies of the anode material based on polymer and starch derived ceramic for lithium ion batteries
PublikacjaThe anode materials derived of preceramic polymer poly(1,2-dimethylsilazane) (PSN) and starch was study. Commercially available polysilazane (poly(1,2-dimethylsilazane (PSN 2M01 Gelest) was mixed with commercially available starch (POCH Gliwice). The ratio polymer/starch (PSN/starch) was 1/1 or 3/7. The polysialazane/starch blend was cross-linked at 230 ºC for 2 h followed by heating to the final temperature (500 ºC, 700 ºC and...
-
Recycled rubber wastes-based polymer composites with flame retardancy and electrical conductivity: Rational design, modeling and optimization
PublikacjaPolymer recycling techniques experience a maturity period of design and application. Rubbers comprise a high proportion of polymer wastes, highly flammable and impossible to re-melt. Polymer composites based on ground tire rubber (GTR) and ethylene-vinyl acetate copolymer (EVA) containing carbon black (CB) (1–50 phr), with variable EVA/GTR weight composition (10/90, 25/75, 50/50, 75/25 and 90/10), and processing temperature (Low:...
-
Load-carrying capacity and state of effort of tubes made of glass and basalt fibre reinforced polymer filled with concrete
PublikacjaOpisano badania eksperymentalne słupów wykonanych z rur polimerowych zbrojonych włóknami szklanymi i bazaltowymi. Część rur wypełniano wewnątrz betonem. Słupy z wypełnieniem niszczyły się w sposób powolny, wykazując wysoką nośność pokrytyczną, podczas gdy słupy z rur pustych niszczyły się w sposób gwałtowny, niesygnalizowany. Nośności uzyskane eksperymentalnie porównano do nośności obliczonych teoretycznie na podstawie procedur...
-
Composite Materials Based on Polymer-Derived SiCN Ceramic and Disordered Hard Carbons as Anodes for Lithium-Ion Batteries
PublikacjaNew composite materials based on polymer-derived SiCN ceramics and hard carbons were studied in view of its application as anodes for lithium-ion batteries. Two kinds of composites were prepared by pyrolysis of the preceramic polysilazane (HTT1800, Clariant) at 1000 °C in Ar atmosphere mixed with hard carbons derived from potato starch (HC_PS) or with a hard carbon precursor, namely potato starch (PS), denoted as HTT/HC_PS and...
-
Initial Field Validation of Poroelastic Pavement Made with Crumb Rubber, Mineral Aggregate and Highly Polymer-Modified Bitumen
PublikacjaTire/road noise in most driving conditions dominates other sources of traffic noise. One of the most efficient ways of reducing tire/road noise is to use the so-called “low noise pavement”. According to numerous studies, at present, poroelastic road pavement that is composed of rubber and mineral aggregate and polyurethane or bituminous binder gives the best noise reduction up to 12 dB. Unfortunately, there are many problems with...
-
Łukasz Piszczyk dr hab. inż.
Osoby -
Michał Strankowski dr hab. inż.
OsobyJest zatrudniony w Katedrze Technologii Polimerów na Wydziale Chemicznym od 2006 roku. W tym samym roku uzyskał stopień doktora nauk technicznych w zakresie technologii chemicznej. Stopień doktora habilitowanego w dziedzinie nauk ścisłych i przyrodniczych uzyskał w 2019 roku. W okresie 2013-2015 pełnił funkcję kierownika projektu „PUR-GRAF” pt. „Nanokompozyty poliuretanowe zawierające zredukowany tlenek grafenu”. Za opracowane...
-
Novel Cell Permeable Polymers of N-Substituted L-2,3-Diaminopropionic Acid (DAPEGs) and Cellular Consequences of Their Interactions with Nucleic Acids
Publikacja -
Molecularly imprinted polymers based on deep eutectic solvents as a greenest materials for selective extraction of emerging contaminants from complex samples
PublikacjaSome of the reagents applied in the synthesis of molecularly imprinted polymers (MIPs) may impact on health and the environment. Thus, a new generation of promising green chemicals are nowadays introduced and investigated, including deep eutectic solvents (DESs). DESs seems to be a reasonable choice as they are characterized as non-toxic, low cost, easy to prepare and biodegradable chemicals. This review presents the information...
-
New coordination polymers based on a V-shaped ligand and lanthanides: Structural description and symmetry-luminescence correlation using europium as a probe
PublikacjaWe have synthesized new luminescent coordination polymers using 4,4'-sulfonyldibenzoic acid (H2SDA) and several lanthanide ions by open crystallization in DMF. Three different 1-D structures were obtained, as determined by single-crystal X-ray diffraction: [La(η2-NO3)(μ-SDA)(DMF)3]n (1), [Sm(η2-NO3)(μ-SDA)(DMF)2 2DMF]n (3), [Ln(η2-NO3)(μ-SDA)(DMF)2 DMF]n (Ln ¼ Eu (4), Dy (5), Ho (6), Er (7), Tm (8) and Lu(9)). A 2-D structure,...
-
Copper and copper-manganese 1D coordination polymers: Synthesis optimization, crystal structure and preliminary studies as catalysts for Baylis–Hillman reactions
PublikacjaThis work reports the influence of experimental parameters (pH and counter-ion) in the synthesis of the 1D coordination polymer [Cu(IDA)(H2O)2]n (IDA = iminodiacetate), named here Cu-IDA. Copper-manganese bimetallic coordination polymers were also obtained by isomorphic replacement into Cu-IDA structure, with different molar ratio of Cu2+ and Mn2+ ions, denoted here as Cu/Mn-IDA (0.9/0.1; 0.7/0.3 and 0.5/0.5). New coordination...
-
Copper(I) halide cluster-based coordination polymers modulated by chiral ditopic dithiodianthranilide ligands: synthesis, crystal structure and photoluminescence
PublikacjaReaction of copper(I) halides with chiral dithiodianthranilidesmdtaandbdtaafforded polymeric complexeswhere polynuclear CuX clusters were linked together by ditopic bridging ligands into 1D chains or 2D layerstructures. In the case of racemic ligands double stranded chain polymers were formed where the Cu4X4(X = I or Br) cores are connected by enantiomeric pairs of the ditopic ligands. In contrast, a homochiralmdtaligand created...
-
Quantum and carbon dots conjugated molecularly imprinted polymers as advanced nanomaterials for selective recognition of analytes in environmental, food and biomedical applications
PublikacjaSamples with complex matrix analyzed during explanation of pathogenesis of various diseases and food or environmental monitoring request advanced analytical and instrumental devices. Among the materials used for described purposes, quantum (QDs) or carbon dots (CDs) layered by molecularly imprinted polymer (MIP) shells have gained widespread attention. Unique optical and physicochemical properties of QDs/CDs together with high...
-
Preliminary Testing of the Influence of Modified Polycaprolactones on Anabaena Variabilis Growth in Seawater
PublikacjaSeveral new biodegradable polymer materials have recently come onto the global market. Mostly the results on degradation kinetic studies are presented. This paper suggests using one of the tests to estimate the impact of polymer packaging material on sea life. The microorganism chosen was Anabaena variabilis (identified in many waters, including those of the Baltic Sea, especially in the Gulf of Gdansk and Puck Bay; this cyanobacterium...
-
Phosphorus, nitrogen and oxygen co-doped polymer-based core-shell carbon sphere for high-performance hybrid supercapacitors
Publikacja -
Temperature Coefficient of Electronic Polarizability in Thin Polymer Films Deposited on Si and SiO2 Substrates Determined via Spectroscopic Ellipsometry
PublikacjaEllipsometry is widely used to determine the thermo-optical properties of thin polymer films. However, if the thermo-optic coefficient (TOC) and the linear thermal expansion coefficient (LTEC) are to be used to determine the temperature coefficient of electronic polarizability (TCEP) in thin polymer films, their values must be determined with the greatest possible accuracy, as both have the opposite effect. In this article,...
-
SU-FF-T-284: Linear Energy Transfer (LET) Dependence of BANG® Polymer Gel Dosimeters in Proton Beams
Publikacja -
Three-dimensional visualization and measurement of conformal dose distributions using magnetic resonance imaging of bang polymer gel dosimeters
Publikacja -
Structure and electrical properties of Y, Fe-based perovskite mixed conducting composites fabricated by a modified polymer precursor method
PublikacjaIn this work, samples of Y0.07Sr0.93Ti1-xFexO3-d with 20, 40, 60 and 80 mol% of iron amount were prepared by a low-temperature polymer precursor method. The SEM-EDS analysis proved that analyzed Y0.07Sr0.93Ti1-xFexO3-d samples were composites of two Ti- and Fe-rich perovskite samples. This kind of composite consists of two phases in which one has a good ionic and the other electronic conductivity, which makes such a composite a...
-
All solid state electrodes taste sensor with modified polymer membranes for discrimination of mineral water with different CO2 content
PublikacjaA potentiometric taste sensor with All Solid State Electrodes containing five all solid state electrodes with appropriate lipophilic compounds (benzyldimethyltetradecylammonium chloride, dodecyltrimethylammonium bromide, palmitic acid, stearic acid, and phytol) embedded in a polymer membrane was applied for discrimination of mineral water samples differed in CO2 content. Samples of still, slightly sparkling, and sparkling Naleczowianka...
-
Anna Lisowska-Oleksiak prof. dr hab.
OsobyAnna Lisowska-Oleksiak, born in 1952, has been working at GUT since 1977. Currently is employed at the Faculty of Chemistry as a full professor. She was employed as a research assistant at the University of St Andrews in the group of C. A. Vincent and P.G. Bruce (1991-1994). She completed a two-month research internship in CEA Grenoble (2011). Anna Lisowska-Oleksiak obtained her MSc in chemistry at Nicolaus Copernicus University...
-
Jakub Kruszyński mgr. inż
OsobyMotivated and focused to steady discovering amazing chemistry of polymer and cooperating with fascinating people. Currently PhD student in cooperation between SABIC B.V and Gdansk University of Technology. I have 3 year industrial experience. Mainly as a R&D Junior Specialist in Synthos S.A and intern in SABIC Technology&Innovation Center, Geleen. Graduate of Gdansk University of Technology in Polymer Specialization on...
-
DESIGNED MONOMERS AND POLYMERS
Czasopisma -
HIGH PERFORMANCE POLYMERS
Czasopisma -
A Series of Novel 3D Coordination Polymers Based on the Quinoline-2,4-dicarboxylate Building Block and Lanthanide(III) Ions—Temperature Dependence Investigations
PublikacjaA series of novel 3D coordination polymers [Ln2(Qdca)3(H2O)x]yH2O (x = 3 or 4, y = 0–4) assembled from selected lanthanide ions (Ln(III) = Nd, Eu, Tb, and Er) and a non-explored quinoline- 2,4-dicarboxylate building block (Qdca2 = C11H5NO4 2) were prepared under hydrothermal conditions at temperatures of 100, 120, and 150 C. Generally, an increase in synthesis temperature resulted in structural transformations and the formation...
-
Coordination polymers of Fe(iii) and Al(iii) ions with TCA ligand: distinctive fluorescence, CO2uptake, redox-activity and oxygen evolution reaction
Publikacja -
Synthesis, characterization and Luminescent Properties of New Coordination Polymers Based on p-tert Butylcalix[4]arene-tetracarboxylic acid and Lanthanine cations
PublikacjaA series of new coordination polymers based on p-tert-butylcalix[4]arene-tetracarboxylic acid with Eu3+, Tb3+wrer prepared by hydro and solvothermal methods. the obtained solid compounds were characterized by infrared and luminescence spectroscopy, powder X-ray diffraction, scianning electron microscopy and thermogravimetric anylisis. The infrared curves and the x-ray diffraction patterns indicate that the same crystalline structure...
-
INTERNATIONAL JOURNAL OF POLYMER ANALYSIS AND CHARACTERIZATION
Czasopisma