Filtry
wszystkich: 1745
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: MULTIPULSE CONVERTERS
-
Prediction of ringing frequencies in DC-DC boost converter
PublikacjaIn the paper ringing phenomena in a DC-DC boost converter is presented. The ringing frequency is calculated using an analytical formula. The necessary wide band models of MOSFET transistor, passive and parasitics are described. The calculation results are verified in simulation and laboratory tests.
-
Power Converter Solutions for Industrial PV Applications—A Review
Publikacja: As the use of photovoltaics becomes more widespread, new technologies for more efficient energy generation, transmission, and distribution based on power electronics converters are being developed. The most common applications are grid-on, energy storage, hybrid, and high voltage gain applications. These applications impose several additional requirements in the design of power converters associated with the solar battery’s maximum...
-
Residue-to-two's complement converter based on core function
PublikacjaW artykule przedstawiono układową realizację konwertera z systemu resztowego do systemu binarnego bazującego na funkcji jądra. Zastosowanie funkcji jądra powoduje zmniejszenie wymagań sprzętowych przy realizacji konwertera. W publikacji omówiono problem dektekcji znaku oraz realizacje ukłądową konwertera w środowisku FPGA.
-
Journal of Computational Multiphase Flows
Czasopisma -
Experimental and Computational Multiphase Flow
Czasopisma -
Evolution-based scheduling of multiple variant and multiple processor programs
Publikacja -
Step-Up DC/DC Converters With Cascaded Quasi-Z-Source Network
Publikacja -
Step-Up DC/DC Converters With Cascaded Quasi-Z-Source Network
PublikacjaW artykule zaprezentowano nowe rozwiązania dotyczące przekształtników energoelektronicznych DC-DC podwyższających napięcie z ogniw paliwowych. Istota rozwiązania zawiera się w zastosowaniu kaskadowo połączonych wejściowych obwodów pasywnych typu Quasi-Z, umozliwiających znaczne podwyższanie napięcia z wykorzystaniem stanu parcy zwarć gałęzi tranzystorowych przekształtnika.
-
High Frequency Harmonics Emission of Modern Power Electronic AC-DC Converters
PublikacjaModern AC/DC converters with bidirectional power flow employing PWM boost topology generate harmonic distortions of input current in relatively high frequency range tightly related to modulation carrier frequency. These frequencies and its multiples in typical applications are usually located in frequency range from single up to several of kHz. Increased harmonic emission in this frequency range can easily and harmfully influence...
-
Energy storage device based on flywheel, power converters and Simulink real-time
PublikacjaThis electronic document is a “live” template and already defines the components of your paper [title, text, heads, etc.] in its style sheet. Paper presents information on Energy Storage Device based on Flywheel and bi-directional IGBT Power Converters – designed for LINTE^2 laboratory owned by Gdansk University of Technology in Poland. Paper is divided into four sections. First section of the paper provides introductory information...
-
An Ultra-Low-Energy Analog Comparator for A/D Converters in CMOS Image Sensors
PublikacjaThis paper proposes a new solution of an ultra-low-energy analog comparator, dedicated to slope analog-to-digital converters (ADC), particularly suited for CMOS image sensors (CISs) featuring a large number of ADCs. For massively parallel imaging arrays, this number may be as high as tens-hundreds of thousands ADCs. As each ADC includes an analog comparator, the number of these comparators in CIS is always high. Detailed analysis...
-
Direct modulation for conventional matrix converters using analytical signals and barycentric coordinates
PublikacjaThis paper proposes the generalized direct modulation for Conventional Matrix Converters (CMC) using the concept of analytical signals and barycentric coordinates. The paper proposes a novel approach to the Pulse Width Modulation (PWM) duty cycle computing, which allows faster prototyping of direct control algorithms. The explanation of the new idea using analytical considerations demonstrating the principles of direct voltage...
-
Multiple-Input Multiple-Output Technique for Underwater Acoustic Communication System
PublikacjaThe performance of an underwater acoustic communication (UAC) system is limited due to tough propagation conditions in the UAC channel. Multiple-Input Multiple-Output (MIMO) technique can improve the reliability of the data transmission system, increase its speed, increase its range, and reduce the energy consumption. The paper presents an implementation method of MIMO technique in the form of coding the Space-Time Block Code and...
-
A Special Multi-Pulse Converter with Small Active Power Filter
Publikacja -
Electromagnetic Field Measurements of Bow Thruster Drive with Frequency Converter
Publikacja -
Assessment of the Impact of Split Storage within Modular Multilevel Converter
Publikacja -
Design and evaluation of a flow-to-frequency converter circuit with thermal feedback
Publikacja -
Solutions of Power Electronics Converter for the Shore - to - Ship Power Systems
PublikacjaW artykule poruszono tematykę zasilania statków zacumowanych w porcie z lądowej sieci elektroenergetycznej poprzez wykorzystanie nowoczesnych konstrukcji przekształtników energoelektronicznych. Zaproponowano budowę sieci dystrybucyjnej prądu stałego, przewoźnej platformy zasilającej oraz zastosowanie zasobników energii
-
Power electronic transformer based on cascaded H-bridge converter
PublikacjaIn this paper the control strategy of power electronic transformer (PET) is proposed. The analyzed structure of PET uses two seven-level cascaded H-bridge (CHB) rectifiers. The electrical power of PET is transferred between DC-links of CHB converters using dual-active-bridges (DABs) and low voltage high frequency transformers. The roposed solution allows for controlling the active and reactive power with a low level of harmonic...
-
Conjugated control of triple active bridge converter with common HFT
PublikacjaPaper presents synthetic analyses of single input, dual output DC/AC/DC converter with common high frequency transformer. Rise the problem of cross-coupling power flows between secondary terminals, under asymmetrical control operating condition. It also proposes a new approach to converter control, based on conjugated phase shift modulation and defines its limitations. Finally, the developed control technique was verified by simulation...
-
Modeling of conducted emission of dc-dc switch-mode converter
PublikacjaW publikacji zaprezentowano sposób modelowania i wyznaczania emisji przewodzonej zaburzeń elektromagnetycznych w przekształtnikach energoelektronicznych. Na przykładzie przekształtnika DC-DC, zostały dobrane odpowiednie narzędzia CAD do szerokopasmowego modelowania i symulacji przekształtnika energoelektronicznego. Otrzymane rezultaty zostały eksperymentalnie potwierdzone i porównane zarówno w dziedzinie czasu jak i częstotliwości...
-
High-speed residue-to-binary converter based on the Chinese RemainderTheorem.
PublikacjaPrzedstawiono szybki konwerter z systemu resztowego do systemu binarnego dla modułów 5-bitowych oparty o chińskie twierdzenie o resztach. Projekcje ortogonalne są generowane przy użyciu odwzorowania realizowanego przy zastosowaniu funkcji logicznych pięciu zmiennych. Wartość wyjściowa jest obliczana przy użyciu drzewaWallace'a z segmentacją wektorów wyjściowych i redukcją do 2M, M zakres liczbowy systemu oraz efektywny finalny...
-
RNS reverse converter based on the new chinese remainder theorem.
PublikacjaPrzeanalizowano złożoność układu cyfrowego opartego na nowej odmianie chińskiego twierdzenia o resztach.
-
High-speed binary-to-residue converter with the reduced input layer
Publikacjaprzedstawiono architekturę szybkiego konwertera z systemu binarnego do systemu resztowego dla modułów 5-bitowych. Algorytm konwersji oparty jest na dodawaniu binarnym reszt potęg liczby 2 obliczonych modulo m i redukcji modulo m sumy dla poszczególnych modułów bazy systemu resztowego. Warstwa wejciowa konwertera jest redukowana poprzez wykorzystanie wspólnych elementów układu dla odpowiednio zestawionych par modułów.
-
Wideband Modeling of DC-DC Buck Converter with GaN Transistors
PublikacjaThe general wideband modeling method of the power converter is presented on the example of DC-DC buck converter with GaN High Electron Mobility Transistors (HEMT). The models of all basic and parasitic components are briefly described. The two methods of Printed Circuit Board (PCB) layout parameter extraction are presented. The results of simulation in Saber@Sketch simulation software and measurements are compared. Next, the model...
-
Pulse-Width Modulation of Power Electronic DC–AC Converter
PublikacjaThe Second Edition of High Performance Control of AC Drives with Matlab®/Simulink delivers an updated and thorough overview of topics central to the understanding of AC motor drive systems. The book includes new material on medium voltage drives, covering state-of-the-art technologies and challenges in the industrial drive system, as well as their components, and control, current source inverter-based drives, PWM techniques for...
-
Audible noise in ship’s electrical drive systems with frequency converters
Dane BadawczeThe presented dataset is part of research focusing on the impact of the ship's electrical drive systems with frequency converters on vibrations and the level of audible noise on ships.
-
Conducted EMI mitigation in switched mode DC-DC converters by spread spectrum techniques
PublikacjaW artykule przedstawiono skuteczność technik rozpraszania widma do ograniczenia emisji przewodzonej EMI dla szeregowego przerywacza napięcia. Badania porównawcze zostały wykonane laboratoryjnie za pomocą generatora funkcyjnego, miernika zaburzeń i sieci sztucznej. Analiza otrzymanych wyników wykazała, szczególnie korzystne do 20 dB, ograniczenie charakterystyki napięcia emisji przewodzonej dla losowej modulacji częstotliuwości...
-
A Direct Modulation for Matrix Converters based on the Onecycle Atomic operation developed in Verilog HDL.
PublikacjaThis paper presents a fast direct Pulse Width Modulation (PWM) algorithm for the Conventional Matrix Converters (CMC) developed in Verilog Hardware Description language (HDL). All PWM duty cycle calculations are performed in one cycle by an atomic operation designed as a digital module using FPGA basic blocks. The algorithm can be extended to any number of output phase. The improved version of the discontinuous Direct Analytic...
-
The Conceptual Research over Low-Switching Modulation Strategy for Matrix Converters with the Coupled Reactors
PublikacjaIn this paper, different Pulse Width Modulation (PWM) strategies for operating with a low-switching frequency, a topology that combines Conventional Matrix Converters (CMCs), and Coupled Reactors (CRs) are presented and discussed. The principles of the proposed strategies are first discussed by a conceptual analysis and later validated by simulation. The paper shows how the combination of CMCs and CRs could be of special interest...
-
Application of Analytic Signal and Smooth Interpolation in Pulse Width Modulation for Conventional Matrix Converters
PublikacjaThe paper proposes an alternative and novel approach to the PWM duty cycles computation for Conventional Matrix Converters (CMC) fed by balanced, unbalanced or non–sinusoidal AC voltage sources. The presented solution simplifies the prototyping of direct modulation algorithms. PWM duty cycles are calculated faster by the smooth interpolation technique, using only vector coordinates, without trigonometric functions and angles. Both...
-
FPGA-Based System for Electromagnetic Interference Evaluation in Random Modulated DC/DC Converters
PublikacjaField-Programmable Gate Array (FPGA) provides the possibility to design new “electromagnetic compatibility (EMC) friendly” control techniques for power electronic converters. Such control techniques use pseudo-random modulators (RanM) to control the converter switches. However, some issues connected with the FPGA-based design of RanM, such as matching the range of fixed-point numbers, might be challenging. The modern programming...
-
Multiple Sclerosis and Related Disorders
Czasopisma -
Multiple Sclerosis and Demyelinating Disorders
Czasopisma -
A unified coarse-grained model of biological macromolecules based on mean-field multipole–multipole interactions
Publikacja -
A low-voltage CMOS negative impedance converter for analogue filtering applications
PublikacjaLow-voltage high-frequency continuous-time filters are still required in many applications and are the subject of continuing research. There are many techniques to realize integrated filters, including OTA C, Opamp RC and MOSFET-C-Opamp. The latter two show high dynamic range at low supply voltage, but their frequency operating range is usually limited to several megahertz. Transconductance filters are dedicated to higher frequencies....
-
Design solution and selected research results of the sea-wave energy converter
PublikacjaW artykule przedstawiono oryginalne rozwiązanie konstrukcyjne boi do pozyskiwania energii fal morskich oraz analizy i badania modelowe turbiny wodnej poprzedzające wybór ostateczny konstrukcji modelu boi w skali 1:5 przewidzianego do badań eksperymentalnych w basenie holowniczym. Zaprezentowano także wybrane wyniki badań modelowych i symulacji komputerowych ukazujący wpływ systemu kotwiczenia i innych parametrów na jakość i efektywność...
-
Electromagnetic interference frequencies prediction model of flyback converter for snubber design
PublikacjaSnubber design for flyback converters usually requires experimental prototype measurements or simulation based on accurate and complex models. In this study simplified circuit modelling of a flyback converter has been described to dimension snubbers in early stage of design process. Simulation based prediction of the transistor and diode ringing frequencies has been validated by measurements in a prototype setup. In that way obtained...
-
Conducted EMI Propagation Paths in DC-AC Hard Switching Converter
PublikacjaIn order to limit the electromagnetic interference (EMI) in power electronics devices, knowledge about the phenomena connected with EMI generation and propagation is necessary. This papers describes the propagation paths in the 3 phase voltage source inverter using wide-band simulation and laboratory test with the signal processing method Wiener filtering, where the transfer functions between voltage across switches and the perturbation...
-
RNS/TCS CONVERTER DESIGN USING HIGH-LEVEL SYNTHESIS IN FPGA
PublikacjaAn experimental high-level synthesis (HLS) of the residue number system (RNS) to two’s-complement system (TCS) converter in the Vivado Xilinx FPGA environment is shown. The assumed approach makes use of the Chinese Remainder Theorem I (CRT I). The HLS simplifies and accelerates the design and implementation process, moreover the HLS synthesized architecture requires less hardware by about 20% but the operational frequency is smaller...
-
Modern control strategy of bidirectional DAB converter with consideration of control nonlinearity
PublikacjaThis paper focuses on the control strategy for modern universal bidirectional Dual Active Bridge (DAB) converters for microgrid systems. An analysis of the converter equations was carried out, and typical problems related to the influence of dead time on the system operation were discussed. A closed control loop was developed, then tested by simulation and on a laboratory stand.
-
Multi-Transformer Flyback Converter for Supplying Isolated IGBT and MOSFET Drivers
PublikacjaA multi transformer flyback converter topology for supplying transistor drivers is presented. The topology presents some advantages over typical multi output single transformer, as reduction of effective leakage inductance, equal magnetic coupling between primary and secondary circuits and better isolation between outputs. Simulation study carried out in the LTSpice IV program and preliminary experimental results indicate high...
-
Adaptive estimation of the transformer stray capacitances for DC–DC converter modelling
PublikacjaNew low cost and accurate estimation method of transformer stray capacitances for wide band DC–DC converter modelling and design is proposed. The Wiener filter (WF) method is applied to estimate the transformer impedance – referred to the selected transformer winding configurations. Laboratory tests are used to adapt the filter, that is to find optimal impedance which minimises mean square error between measured, noise perturbed...
-
AC-DC-DC Converter for Small Power Energy Storage Systems
PublikacjaThe energy transformation driven by the development of renewable energy sources has become a reality for all power grid users. Prosumer energy, primarily utilizing photovoltaic installations, is one of the fastest-growing market segments. The advancement of technology, a decrease in electrochemical energy storage prices, and changes in the legal framework governing energy billing for grid-fed power have led to a growing interest...
-
Design and Evaluation of the Compact and Autonomous Energy Subsystem of a Wave Energy Converter
PublikacjaThis paper presents the results of the design process focused on the development of the energy subsystem (ES) of a wave energy converter (WEC). The ES is an important electrical part that significantly affects the energy reliability and energy efficiency of the entire WEC device. The designed ES was intended for compact WECs powering IoT network devices working in the distributed grid. The developed ES is an electronic circuit...
-
Power converter interface for urban DC traction substations - solutions and functionality.
PublikacjaThis paper focuses on extending an urban DC traction substation functionality by means of an additional power converter interface (PCI). In particular, by enabling bidirectional energy exchange between LV DC traction grid, AC grid and V2G chargers. Among other things, the presented material compares general attributes of the most promising DC/DC converters that can be used in a PCI, meet the requirements of galvanic isolation and...
-
Feedback Control of Doubly-Fed Generator Connected to Current Source Converter
PublikacjaDoubly-fed induction generator (DFIG) system supplied by current source converter (CSC) is considered in this article. The DFIG can work in two independent modes: AC grid connection and stand-alone mode. The DFIG is connected to the ac grid directly through its stator and the CSC links the rotor side. In this mode, the active and reactive powers of the DFIG must be controlled. This article proposes two control system structures...
-
EMI attenuation in a DC-DC buck converter using GaN HEMT
PublikacjaA dc-dc buck converter using gallium nitride (GaN) high electron mobility transistors (HEMT) is experimentally investigated at the discontinuous current mode (DCM) and at the triangular current mode (TCM) operation. The paper objective is to specify the power conversion efficiency and attenuation of common mode (CM) and differential mode (DM) noise voltage, measured at the line impedance stabilization network (LISN) for compared...
-
Potential of silicon carbide MOSFETs in the DC/DC converters for future HVDC offshore wind farms
Publikacja -
An Extended Control of the Input Angle for Matrix Converters Connected with the Non-Unity Power Factor Loads.
PublikacjaThis paper proposes a novel PWM modulation algorithm for Multiphase Conventional Matrix Converters (MCMC), with 3 inputs and k outputs, using the transfer function of the load angle. The proposed approach extends the range of power angle control at the input during the operation with a maximum voltage transfer ratio. The proposed concept is based on the Direct Analytic Voltage PWM (DAV--PWM) modulation with an elliptical trajectory...