Search
Filters
total: 6575
filtered: 4740
displaying 1000 best results Help
Search results for: SURFACE TOPOGRAPHY MEASUREMENTS
-
Reduction of Influence of the High-Frequency Noise on the Results of Surface Topography Measurements
Publication -
The effect of valley depth on areal form removal in surface topography measurements
Publication -
Thresholding Methods for Reduction in Data Processing Errors in the Laser-Textured Surface Topography Measurements
Publication -
Application of image processing methods for the characterization of selected features and wear analysis in surface topography measurements
Publication -
Suppression of the High-Frequency Errors in Surface Topography Measurements Based on Comparison of Various Spline Filtering Methods
Publication -
Fracture surface topography measurements analysis of low-alloyed corrosion resistant steel after bending-torsion fatigue tests
PublicationIn this paper, an assessment of a topography measurement method for fracture surfaces of 10HNAP steel after bending-torsion fatigue tests was performed. Surface roughness was measured by using a non-contact Focus Variation Microscopy (FVM) technique in which the non-measured points (NMPs) and outliers (spikes) were removed by the application of general methods. The results revealed, that the optical measurement method introduced...
-
Influence of surface topography on RBS measurements: case studies of (Cu/Fe/Pd) multilayers and FePdCu alloys nanopatterned by self-assembly
Publication -
Fast Fourier Transform detection and reduction of high-frequency errors from the results of surface topography profile measurements of honed textures
Publication -
Detection of measurement noise in surface topography analysis
Publication -
Problems of surface topography with oil pockets analysis
Publication -
The Effect of Dimple Distortions on Surface Topography Analysis
Publication -
The Influence of Laser Alloying of Ti13Nb13Zr on Surface Topography and Properties
PublicationThe laser alloying is a continually developing surface treatment because of its significant and specific structuration of a surface. In particular, it is applied for Ti alloys, being now the most essential biomaterials` group for load-bearing implants. The present research was performed on the Ti13Nb13Zr alloy subject to laser modification in order to determine the treatment effects on surface topography and its some mechanical...
-
The Effect of Valley Location in Two-Process Surface Topography Analysis
Publication -
Resolving Selected Problems in Surface Topography Analysis by Application of the Autocorrelation Function
Publication -
Errors of Surface Topography Parameter Calculation in Grinded or Turned Details Analysis
Publication -
Roughness Evaluation of Burnished Topography with a Precise Definition of the S-L Surface
Publication -
Parametric and nonparametric description of the surface topography in the dry and MQCL cutting conditions
Publication -
Entire fracture surface topography parameters for fatigue life assessment of 10H2M steel
PublicationIn this paper, the entire fracture surface approach was used to assess an effect of 280,000 h of exploitation under internal pressure of 2.9 MPa and high temperature of 540 °C on the fatigue response of 10H2M (10CrMo9–10) power engineering steel. The mechanical testing was carried out on the hourglass specimens produced from the as-received, unused pipeline and the same material after long-time exploitation. The uniaxial tensile...
-
The effect of random surface topography height on fretting in dry gross slip conditions
Publication -
Fracture surface topography investigation and fatigue life assessment of notched austenitic steel specimens
PublicationThe objectives of this study were to investigate the fracture surface topography of X8CrNiS18-9 austenitic stainless-steel specimens for different loadings and notch radii and to supplement the knowledge about the fracture mechanisms for fatigue performance. Cases with three different values of the notch radius ρ and the stress amplitude σa were analysed. The fracture topographies were quantified by the areas over their entire...
-
Laser-textured cross-hatched surface topography analysis with evaluation of high-frequency measurement noise
PublicationThe precision of surface roughness determination using ISO 25178 parameters relies on various factors that directly impact the measurement process. In industry applications, the contactless roughness measurement reduces data collection time. However, it introduces several potential errors, including those stemming from the environment. One of the main types of errors encountered during topography analysis is measurement noise,...
-
Surface topography analysis based on fatigue fractures obtained with bending of the 2017A-T4 alloy
Publication -
Comparative study of surface topography of high performance liquid chromatography columns in terms of hydrophobicity
Publication -
Feature-Based Characterisation of Turned Surface Topography with Suppression of High-Frequency Measurement Errors
Publication -
Proposals of Frequency-Based and Direction Methods to Reduce the Influence of Surface Topography Measurement Errors
Publication -
The Effect Of Reference Plane On Values Of Areal Surface Topography Parameters From Cylindrical Elements
Publication -
Influence of surface roughness topography on properties of water lubricated polymer bearings, experimental research
PublicationW artykule przedstawiono wyniki badań eksperymentalnych, których celem było zidentyfikowanie wpływu ułożenia chropowatości na powierzchni ślizgowej łożyska smarowanego wodą z polimerową panwią. Badania wykazały, że wpływ ten jest mniejszy niż oczekiwano a na własności łożyska ma wpływ głównie wysokość chropowatości.
-
Strain sequence effect on fatigue life and fracture surface topography of 7075-T651 aluminium alloy
PublicationThe paper studies the effect of strain-loading sequence on fatigue lifetime and fracture surface topographies in 7075-T651 aluminum alloy specimens. Fatigue tests were performed in two ways: (i) constant-amplitude loading and (ii) two series of variable amplitude loading with non-zero mean strain values. The topography of the fatigue fractures was measured over their entire surfaces with the help of an optical confocal measurement...
-
Fracture Surface Topography Parameters for S235JR Steel Adhesive Joints After Fatigue Shear Testing
PublicationThis paper presents the experimental results of a study investigating the effect of holes and notches made on the overlap ends on the strength of adhesive joints. Single-lap joints made of S235JR steel sheets bonded with Araldite 2024-2 epoxy adhesive were tested. For comparative reasons, static shear strength tests and high-cycle fatigue strength tests were performed. Adhesive-filled joints having three holes, each with a diameter...
-
Strain sequence effect on fatigue life and fracture surface topography of 7075-T651 aluminium alloy
Publication -
Evaluation of the Surface Topography of Ti6Al4V Alloy after the Finish Turning Process under Ecological Conditions
Publication -
Formation of Surface Topography During Turning of AISI 1045 Steel Considering the Type of Cutting Edge Coating
Publication -
Evaluation of Surface Topography after Face Turning of CoCr Alloys Fabricated by Casting and Selective Laser Melting
Publication -
Surface quality control of a thin SiN layer by optical measurements
PublicationFiber optic interferometers have a wide range of applications, including biological and chemical measurements. Nevertheless, in the case of a reflective interferometer setup, standard silver mirrors cannot be used in every measurement, due to their chemical activity. This work investigates the surface quality of a thin optical layer of silicon nitride (SiN), which can serve as an alternative material for silver mirrors. We present...
-
A brief note on entire fracture surface topography parameters for 18Ni300 maraging steel produced by LB-PBF after LCF
PublicationThe concept of entire fracture surface investigation is helpful in explaining fatigue phenomena. In this paper, this method has been applied for 18Ni300 maraging steel using a 3D measurement system. Before post-mortem analysis, the specimens produced by laser beam powder bed fusion (LB-PBF) were tested under low-cycle fatigue (LCF) for eight strain amplitudes in the interval 0.3% to 1.0%. The attention was placed on the relationship...
-
Representativity of ISO test track surface based on controlled pass-by measurements
PublicationWithin the Polish-Norwegian research project ELANORE, a limited Round Robin Test has been performed on four ISO tracks in Northern Europe. The basic objective of the project is to improve the EU directive on labelling of tyres for noise and rolling resistance. This directive is based on the measurement procedures proscribed in the UNECE Reg.117. Measurements on 3 ISO tracks were performed in 2021 and presented at InterNoise 2022....
-
Could thermal imaging supplement surface electromyography measurements for skeletal muscles?
PublicationAbstract—(1) Background: The aim of this study is to present the results of experiments in which surface electromyography (sEMG) and thermal imaging were used to assess muscle activation during gait and to verify the hypothesis that there is a relationship in the case of low fatigue level between sEMG measured muscle activation, assessed in the frequency domain, and thermal factors calculated as minimum, maximum, kurtosis, mean,...
-
Measurements of surface roughness of heads of human hip joints in lubrication aspects
PublicationW niniejszej pracy przedstawiono wyniki pomiarów chropowatości chrząstki stawowej na powierzchniach głów kostnych stawu biodrowego człowieka. Pomiarów dokonano przy pomocy czujników mechanicznych i laserowych. Praca zawiera wyniki analizy statystycznej.
-
A fractographic study exploring the fracture surface topography of S355J2 steel after pseudo-random bending-torsion fatigue tests
Publication -
The Effect of Surface Topography Feature Size Density and Distribution on the Results of a Data Processing and Parameters Calculation with a Comparison of Regular Methods
Publication -
Measurements and calculations of the width of the fracture process zones on the surface of notched concrete beams
PublicationArtykuł omawia wyniki pomiaru i analizy numerycznej szerokości strefy pękania w belkach betonowych z nacięciem. Do pomiarów zastosowano metodę DIC. Do symulacji zastosowano model sprężysto - plastyczny i model z degradacją sztywności. Oba modele zostały rozszerzone o nielokalne osłabienie. Wyniki symulacji porównano z doświadczeniami.
-
Effects of extreme pressure and anti-wear additives on surface topography and tool wear during MQCL turning of AISI 1045 steel
Publication -
The Smith-Watson-Topper parameter and fracture surface topography relationship for additively manufactured 18Ni300 steel subjected to uniaxial variable-amplitude loading
PublicationIn this paper, the association between Smith-Watson-Topper (SWT) parameter and fracture surface topography is studied in additively manufactured maraging steel exposed to variable-amplitude fatigue loading. The post-failure fracture surfaces were examined using a non-contact 3D surface topography measuring system and the entire fracture surface method. The focal point is on the correspondence between fatigue characteristics, articulate...
-
Assessment of copper surface coverage with corrosion inhibitor using AFM-based local electrical measurements
PublicationThe paper presents a new method of assessment of metal surface coverage with corrosion inhibitor and thus of inhibitor protective performance. It is based on the atomic force microscopy measurement performed in a contact mode. Apart from topography images the proposed approach allows acquisition of local DC maps and local electrical impedance spectra via application of DC bias voltage or AC perturbation signal between the conductive...
-
The Use of Unmanned Surface Vessels in Bathymetric Measurements of Waterbodies with Highly Dynamic Seafloor Relief
PublicationThe early 21st century is a time when unmanned surface vessels (USV) are used in various measurement applications. Modern autonomous and unmanned vessels are increasingly often used in bathymetric measurements whose aim is to measure the seafloor with the sufficient positioning accuracy. Therefore, the use of USVs in hydrography can be seen as the beginning of a new era in this regard. This paper presents bathymetric measurements...
-
Temperature influence on tyre/road noise on poroelastic road surface based on laboratory measurements
PublicationThe temperature effect on measured tyre/road noise is very important phenomena as it may lead to significant errors in measurement results due to substantial influence of this parameter on the obtained values. It depends mainly on the particular tyre-road combination. It is different for dense and porous as well as for bituminous and cement concrete pavements. It differs also depending on tested tyre. The correction procedure for...
-
Inverse determination of sliding surface temperature based on measurements by thermocouples with account of their thermal inertia
PublicationThis study developed an inverse heat conduction algorithm to determine temperature at a sliding surface taking account of thermocouple thermal inertia. The direct heat conduction problem was solved analytically based on the Laplace integral transform approach. The inverse algorithm was applied to the problem of friction of a brake material against a steel. The experiments were conducted on a pin-on-disc tribometer for three short-time...
-
A brief note on monotonic and fatigue fracture events investigation of thin-walled tubular austenitic steel specimens via fracture surface topography analysis (FRASTA)
PublicationThe main objective of this short communication is to show the fracture progression in each loading case and complement knowledge about fracture mechanisms underpinning the tensile and fatigue performance of thin-walled tubes. For this purpose, the fracture surface topography analysis (FRASTA) method was used in the thin-walled tubular austenitic stainless-steel specimens. Two cases were analyzed: monotonic tension, and uniaxial...
-
Methodology for Carrying Out Measurements of the Tombolo Geomorphic Landform Using Unmanned Aerial and Surface Vehicles near Sopot Pier, Poland
PublicationThe human impact on the ecosystem has been particularly evident in the last century; it transforms the Earth’s surface on an unprecedented scale and brings about irreversible changes. One example is an oceanographic phenomenon known as a tombolo, i.e., a narrow belt connecting the mainland with an island lying near the shore formed as a result of sand and gravel being deposited by sea currents. The phenomenon contributes to an...
-
Methodology for carrying out measurements of the tombolo geomorphic landform using Unmanned Aerial and Surface Vehicles near Sopot pier, Poland
Publication