Search
Filters
total: 141
Search results for: WIDEBAND MEASUREMENTS
-
Wideband Channel Measurements for Polarised Indoor Off-Body Communications
PublicationThis paper presents the initial results of wideband channel measurements for polarised off-body communication at 5.8 GHz, in an indoor environment. Channel Impulse Response measurements were performed simultaneously for two orthogonal polarisations of the wearable antenna, and repeated for vertical and horizontal orientations of the off-body one. Four types of measurement scenarios were considered in order to investigate the influence...
-
Path Loss Measurements in Wideband Radio Link Designed for Maritime Environment
PublicationIn the article, the research and analysis of path loss in designed and evaluated digital radio link for high-speed data transmission in maritime environment is presented. Collected samples of received signal were used to determine the mean path loss and its standard deviation. Measuring campaign was carried out in a real maritime conditions. The mean value of path loss reached 126 dB on a distance of 11.16 km.
-
Wideband Off-Body Channel Characteristics with Dynamic User
PublicationThis paper presents the preliminary results of a dynamic off-body channel characterisation study, based on wideband measurements at 5.8 GHz in an indoor environment. The Channel Impulse Response (CIR) was measured for a scenario with the user approaching and departing from the off-body antenna. A CIR deconvolution procedure was performed jointly in two polarisations, and the received signal power, Cross-Polarisation Discrimination...
-
Multifrequency Wideband Sonar Array
PublicationThis paper describes of new approach to Multifrequency Wideband Arrays (MWA),applied piezocomposite technologies of the array elements. MWA operating in transmitting(Tx) and receiving (Rx) mode on two or three bands, requires state-of-the-art technology andefficient array designing than conventional array in which separate arrays for every band oreven separate Tx and Rx transducers/arrays are used. The new piezocomposite elements...
-
Wideband Modeling of DC-DC Buck Converter with GaN Transistors
PublicationThe general wideband modeling method of the power converter is presented on the example of DC-DC buck converter with GaN High Electron Mobility Transistors (HEMT). The models of all basic and parasitic components are briefly described. The two methods of Printed Circuit Board (PCB) layout parameter extraction are presented. The results of simulation in Saber@Sketch simulation software and measurements are compared. Next, the model...
-
Wideband Highly-Selective Bandpass Filtering Branch-Line Coupler
PublicationThis paper presents a novel design of a wideband highly-selective bandpass filtering branch-line coupler (FBLC). By integrating a coupled microstrip line, and an open-ended stub at each port of a single-section BLC, bandpass filtering characteristics with excellent selectivity and broad operating bandwidth have been achieved. The proposed circuit has been verified through EM simulations and physical measurements of the fabricated...
-
An NO2 sensor based on WO3 thin films for automotive applications in the microwave frequency range
PublicationA microwave system dedicated to the detection of nitrogen dioxide in the harsh environment of the Norway highways is proposed. An optimized transmission line type of sensor coated with a tungsten trioxide thin film that changes its electrical properties under NO2 gas exposure is developed. The sensors' response (S) is given in °/GHz and it is calculated based on wideband measurements. The advantage of wideband measurements in comparison...
-
A Wideband Channel Model for Body Area Networks in Circular Metallic Indoor Environments
PublicationIn this paper, the wideband characterization of the propagation channel in circular metallic indoor environments is addressed, regarding Body Area Networks and 5G small cells, an analytical model for the dependence of the mean delay and the average delay spread on the circle radius, the working frequency and the distance between the transmitter and the receiver being proposed. The derivation of the model is initially done analytically,...
-
Lokalizacja osób w środowisku promu pasażerskiego z wykorzystaniem ultra szerokopasmowego interfejsu radiowego
PublicationW niniejszym artykule przedstawiono badania efektywności lokalizowania poruszających się osób w środowisku promu pasażerskiego stosując pomiar czasu propagacji ultraszerokopasmowego sygnału radiowego UWB (Ultra-Wide Band) pomiędzy węzłami odniesienia i terminalem ruchomym. Opisano zbudowane stanowisko badawcze oraz uzyskane wyniki pomiarów przeprowadzonych w warunkach rzeczywistych.
-
Numerically Efficient Miniaturization-Oriented Optimization of an Ultra-Wideband Spline-Parameterized Antenna
PublicationDesign of ultra-wideband radiators for modern handheld applications is a challenging task that involves not only selection of an appropriate topology, but also its tuning oriented towards balancing the electrical performance and size. In this work, a low-cost design of a compact, broadband, spline-parameterized monopole antenna has been considered. The framework used for the structure design implements trust-region-based methods,...
-
Design and Optimization of a Compact Planar Radiator for UWB Applications and Beyond
PublicationA compact monopole antenna for ultra-wideband (UWB) and beyond applications has been proposed. The radiator is based on the monopole topology. The super-wideband behavior has been achieved using a combination of spline-based modifications applied to the driven element, as well as utilization of a tapered feed and a slot-modified ground plane. The electrical performance of the structure has been tuned using a numerical optimization...
-
Distribution of roughness and waviness components of turned surface profiles
PublicationThe paper presents a spectral formulation of surface profile irregularity in a wideband frequency range for roughness, waviness and shape components along the measured length. A unique distribution of roughness and waviness components is proposed, according to the nature of their origination in the course of machining with tools of defined cutting edge, as distinct from standard filtration in measurements of surface irregularities....
-
System Loss Model for Body Area Networks in Room Scenarios
PublicationThis paper presents an analysis of system loss in Body Area Networks for room scenarios, based on a wideband measurement campaign at 5.8 GHz. The measurements were performed with a fixed antenna transmitting vertically and horizontally polarised signals, while the user wears dualpolarised antennas. The average system losses in co- and crosspolarised channels are 41.4 and 42.6 dB for vertically polarised transmitted signals and...
-
Design and Optimization of a Compact Super-Wideband MIMO Antenna with High Isolation and Gain for 5G Applications
PublicationThis paper presents a super-wideband multiple-input multiple-output (SWB MIMO) antenna with low profile, low mutual coupling, high gain and compact size for microwave and millimeter wave (mm-wave) fifth-generation (5G) applications. A single antenna is a simple elliptical-square shape with a small physical size of 20 × 20 × 0.787 mm3. The combination of both square and elliptical shapes results in an exceptionally broad impedance...
-
Fast Simulation-Driven Design of a Planar UWB Dipole Antenna with an Integrated Balun
PublicationThe paper presents a design of an ultra-wideband (UWB) antenna with an integrated balun. A fully planar balun interfacing the microstrip input of the structure to the coplanar stripline (CPS) input of the dipole antenna is introduced. The electromagnetic (EM) model of the structure includes the dipole, the balun, and the microstrip input to account for interactions over the UWB band. The EM model is adjusted for low reflection...
-
Design of a Planar UWB Dipole Antenna with an Integrated Balun Using Surrogate-Based Optimization
PublicationA design of an ultra-wideband (UWB) antenna with an integrated balun is presented. A fully planar balun configuration interfacing the microstrip input of the structure to the coplanar stripline (CPS) input of the dipole antenna is introduced. The electromagnetic (EM) model of the structure of interest includes the dipole, the balun, and the microstrip input to account for coupling and radiation effects over the UWB band. The EM...
-
Compressive Sensing Approach to Harmonics Detection in the Ship Electrical Network
PublicationThe contribution of this paper is to show the opportunities for using the compressive sensing (CS) technique for detecting harmonics in a frequency sparse signal. The signal in a ship’s electrical network, polluted by harmonic distortions, can be modeled as a superposition of a small number of sinusoids and the discrete Fourier transform (DFT) basis forms its sparse domain. According to the theory of CS, a signal may be reconstructed...
-
A structure and design optimization of novel compact microscrip dual-band rat-race coupler with enhanced bandwidth
PublicationIn the letter, a topology of a novel compact wideband dual-band rat-race coupler has been presented along with its computationally efficient design optimization procedure. Reduction of the circuit size has been achieved by meandering transmission lines of the conventional circuit. At the same time, the number of independent geometry parameters has been increased so as to secure sufficient flexibility of the circuit, necessary in...
-
Numerical optimization of planar antenna structures using trust-region algorithm with adaptively adjusted finite differences
Open Research DataThe dataset contains initial designs and optimization results for three planar structures that include quasi-patch antenna for WLAN applications, compact spline-parameterized monopole dedicated for ultra-wideband applications, as well as rectifier for energy harvesting with enhanced bandwidth. The numerical results for the first two structures are also...
-
A compact spline-enhanced monopole antenna for broadband/multi-band and beyond UWB applications
PublicationIn this work, a compact monopole antenna for broadband/multi-band and beyond ultra- wideband (UWB) communication has been proposed. The structure is based on a spline-enhanced radiator with a broadband feed and a modified ground plane. Rigorous design optimization of the radiator has been performed in a two-stage framework where optimization of the structure with respect to electrical performance is followed by explicit miniaturization...
-
Badanie i analiza efektywności alokacji strumieni danych w heterogenicznej sieci WBAN
PublicationW niniejszej dysertacji doktorskiej poddano dyskusji efektywność alokacji strumieni danych w heterogenicznej radiowej sieci WBAN (Wireless Body Area Networks). Biorąc pod uwagę dynamiczny rozwój nowoczesnych sieci radiokomunikacyjnych piątej generacji (5G), którego część stanowią radiowe sieci działające w obrębie ciała człowieka, bardzo ważnym aspektem są metody maksymalizujące wykorzystanie dostępnych zasobów czasowo –częstotliwościowych...
-
Concept of Compatibility Region for the Evaluation of IR UWB Electromagnetic Compatibility
PublicationThis paper presents a new proposal for the unified evaluation of ultra wideband and narrowband radio communication systems electromagnetic compatibility, called “compatibility region”. The idea of compatibility region is based on the relation between the ratio of narrowband to ultra wideband signal power in a receiver and some transmission quality indicators (bit error rate, effective data rate).
-
IEEE 802.15.4a Impulse Radio Spectrum Shaping by Changes in Pulse Sequence
PublicationThis paper presents one of possible techniques of IEEE 802.15.4a ultra-wideband signal spectrum control, based on changes in sequences of transmitted pulses with very short duration time. This technique can reduce probability of mutual interferences between new ultra-wideband and existing narrowband devices, which may be helpful in further studies on allowing UWB transmission in wider range of spectrum in theEuropean Union.
-
High quality speech codec employing sines+noise+transients model
PublicationA method of high quality wideband speech signal representation employing sines+transients+noise model is presented. The need for a wideband speech coding approach as well as various methods for analysis and synthesis of sines, residual and transient states of speech signal is discussed. The perceptual criterion is applied in the proposed approach during encoding of sines amplitudes in order to reduce bandwidth requirements and...
-
Size reduction of ultra-wideband antennas with efficiency and matching constraints
PublicationAntenna design is a multifaceted task that involves handling of various performance figures concerning both electrical performance of the structure as well as its geometry. Simultaneous control of several objectives through rigorous optimization is very challenging and virtually impossible through conventional approaches such as parameter sweeping. In this work, we investigate size reduction of ultra‐wideband antenna structures...
-
Speech codec enhancements utilizing time compression and perceptual coding
PublicationA method for encoding wideband speech signal employing standardized narrowband speech codecs is presented as well as experimental results concerning detection of tonal spectral components. The speech signal sampled with a higher sampling rate than it is suitable for narrowband coding algorithm is compressed in order to decrease the amount of samples. Next, the time-compressed representation of a signal is encoded using a narrowband...
-
Ultrawideband transmission in physical channels: a broadband interference view
PublicationThe superposition of multipath components (MPC) of an emitted wave, formed by reflections from limiting surfaces and obstacles in the propagation area, strongly affects communication signals. In the case of modern wideband systems, the effect should be seen as a broadband counterpart of classical interference which is the cause of fading in narrowband systems. This paper shows that in wideband communications, the time- and frequency-domain...
-
Design of a Wideband High-Gain Monopulse Antenna for X- and Ku-Bands Applications
PublicationThe present study provides a wideband high-gain monopulse antenna based on a dielectric lens operating in X- and Ku-bands, in which a wideband dielectric lens is designed and employed to fulfill the radiation pattern and bandwidth necessities of a monopulse antenna. The proposed configuration has four horns allowing for the simultaneous creation of 1 and 6 designs in two perpendicular planes. The main advantages of the proposed...
-
Reduced-cost constrained miniaturization of wideband antennas using improved trust-region gradient search with repair step
PublicationIn the letter, an improved algorithm for electromagnetic (EM)-driven size reduction of wideband antennas is proposed. Our methodology utilizes variable-fidelity EM simulation models, auxiliary polynomial regression surrogates, as well as multi-point response correction. The constraint handling is implicit, using penalty functions. The core optimization algorithm is a trust-region gradient search with a repair step added in order...
-
Rapid multi-objective design optimization of miniaturized impedance transformer by Pareto front exploration
PublicationFast multi-objective optimization of compact impedance transformer is discussed. A set of alternative designs representing possible trade-offs between conflicting design criteria, i.e., electrical performance (here, wideband matching) and the structure size, is obtained through Pareto front exploration by means of surrogate-assisted methods.
-
Design of Compact and Wideband Groove Gap Waveguide-Based Directional Couplers
PublicationThis paper proposes a compact cross-shaped groove gap waveguide structure for creating wideband and compact directional couplers with different coupling levels. Groove gap waveguide technology is applied to overcome fabrication challenges of printed and hollow waveguide structures in high frequency bands. The validity of the novel concept is demonstrated through the design and evaluation of several compact broadband directional...
-
Improved Bandwidth of Microstrip Wide-Slot Antenna Using Gielis Curves
PublicationThe development of a broadband printed wide-slot antenna based on Gielis curves is presented in this article. The printed wide-slot antenna can be conveniently reshaped to achieve ultra-wideband performance by using superformula. The distinct advantage of employing the superformula in design of wide-slot antenna lies in its ability to define nearly any geometric shape including non-standard, complex and non-intuitive for the wide-slot...
-
New method of IEEE 802.15.4a UWB Impulse Radio Spectrum Shaping
PublicationThis paper presents a new technique of IEEE 802.15.4a ultra-wideband signal spectrum control, based on changes in sequences of transmitted pulses with very short duration time. Basic parameters of UWB signal and outline of proposed spectrum shaping methods are briefly described. The main part of the paper presents influence of signal and algorithms parameters on the results of spectrum shaping.
-
Wideband Radio Direction Finder Implemented in Software Defined Radio Technology
PublicationIn the paper a wideband radio direction finder (RDF) implemented in software defined radio (SDR) technology and the results of hardware layer research, including developed antenna switching unit (ASU), are presented. The results of tests of the devices, which are the part of the software defined radio platform (SDRP), and antenna switching unit, confirmed the possibility of using selected components in the final solution.
-
Design Space Reduction for Expedited Multi-Objective Design Optimization of Antennas in Highly-Dimensional Spaces
PublicationA surrogate-based technique for efficient multi-objective antenna optimization is discussed. Our approach exploits response surface approximation (RSA) model constructed from low-fidelity antenna model data (here, obtained through coarse-discretization electromagnetic simulations). The RSA model enables fast determination of the best available trade-offs between conflicting design goals. The cost of RSA model construction for multi-parameter...
-
Fast Antenna Optimization Using Gradient Monitoring and Variable-Fidelity EM Models
PublicationAccelerated simulation-driven design optimization of antenna structures is proposed. Variable-fidelity electromagnetic (EM) analysis is used as well as the trust-region framework with limited sensitivity updates. The latter are controlled by monitoring the changes of the antenna response gradients. Our methodology is verified using three compact wideband antennas. Comprehensive benchmarking demonstrates its superiority over both...
-
BUILT IN PERFORMANCE EVALUATION FOR AN ADAPTIVE NOTCH FILTER
PublicationThe problem of estimating instantaneous frequency of a non- stationary complexsinusoid (cisoid) buried in wideband no ise is considered. The proposed approach extends adaptive notc h filtering algorithm with a nontrivial performance assessme nt mechanism which can be used to optimize frequency tracking performance of the adaptive filter. Simulation results confi rm that the proposedextension allows one to improveaccuracyo f frequency...
-
Hyperbolic position location estimation in the multipath propagation environment
PublicationThe efficiency analysis a hyperbolic position location estimation in the multipath propagation environment in the wideband code division multiple access (WCDMA) interface was presented. Four, the most popular methods: Chan's, Foy's, Fang's and Friedlander's were considered. These algorithms enable the calculation of the geographical position of a mobile station (MS) using the time differences of arrival (TDOA) between several base...
-
Multifrequency self-optimizing narrowband interference canceller
PublicationThe problem of cancellation of a nonstationary sinusoidal interference, acting at the output of a linear stable plant, is considered. It is assumed that disturbance is a multifrequency narrowband signal, and that system output is contaminated with wideband noise. It is not assumed that the reference signal is available. Two disturbance cancelling schemes are proposed, one for disturbances with unrelated frequency components, and...
-
Wideband Signal Generation for Jamming Radio-Controlled Improvised Explosive Devices
PublicationThis paper focuses on modelling operation of a wideband jamming signal generator, considering the effects present in real device which influence the shape of transmitted signal’s spectrum. Introduction is followed by a brief overview of AEGIS project, aim of which is to develop a mobile generator of electromagnetic curtain. Next, simulation model is described which includes the factors...
-
Estimation of Coherence Bandwidth for Underwater Acoustic Communication Channel
PublicationA shallow underwater acoustic communication channel is characterized by strong multipath propagation. The signal reaching the receiver consists of a direct waveform and a number of its delayed and suppressed replica. A significant time dispersion of the transmitted signal and selective fading of its spectrum are observed. Coherence bandwidth defines maximal bandwidth, wherein the channel amplitude characteristic remains constant...
-
A new approach to active noise and vibration control - [Part II: unknown frequency case]
PublicationThis paper presents a new approach to rejection of complex-valued sinusoidal disturbances acting at the output of a discrete-time stable linear plant with unknown and possibly timevarying dynamics. It is assumed that both the instantaneous frequency of the sinusoidal disturbance and its amplitude may be slowly varying with time and that the output signal is contaminated with wideband measurement noise. It is not assumed that a...
-
Parallel frequency tracking with built-in performance evaluation
PublicationThe problem of estimation of instantaneous frequency of a nonstationary complex sinusoid (cisoid) buried in wideband noise is considered. The proposed approach employs a bank of adaptive notch filters, extended with a nontrivial performance assessment mechanism which automatically chooses the best performing filter in the bank. Additionally, a computationally attractive method of implementing the bank is proposed. The new structure...
-
Application of IR UWB Spectrum Shaping to IEEE 802.15.4a Standard
PublicationCoexistence of existing narrowband systems and new ultra wideband devices in the same frequency range requires using some interference mitigation techniques, for example based on spectrum shaping. This paper presents efficiency of impulse radio spectrum shaping methods, applied to IEEE 802.15.4a UWB alternate physical layer signals. Basic parameters of 802.15.4a signal structure and outline of proposed spectrum shaping methods...
-
A Concept and Design Optimization of Compact Planar UWB Monopole Antenna
PublicationA novel structure concept of a compact UWB monopole antenna is introduced together with a low-cost design optimization procedure. Reduced footprint is achieved by introduction of a protruded ground plane for current path increase and a matching transformer to ensure wideband impedance matching. All geometrical parameters of the structure are optimized simultaneously by means of surrogate based optimization involving variable-fidelity...
-
Space-mapping-based design flow of miniaturized broadband matching transformer with perforated metallization
PublicationA fast design procedure of unconventional passive components has been presented and experimentally validated on the basis of a wideband microstrip four-section matching transformer (50:6 OHm). A classic impedance matching circuit has been miniaturized by means of compact microstrip resonant cells (CMRCs) leading to a considerable length reduction (34%) together with minor degradation in its performance. The spacemapping-based design...
-
Laboratory Stand for Wideband Analysis Radiocommunication Signals
PublicationA laboratory stand for wideband analysis radiocommunication signals is presented in the paper. The stand is designed for signals acquisition in wide spectrum and research a field of digital signal processing. Procedures used for simultaneous acquiring many frequency channels in selected wide band are described. The method of detection of direct sequence spread spectrum signals (DS SS) which power spectral density is lower than...
-
Laboratory stand for wideband analysis radiocommunication signals
PublicationA laboratory stand for wideband analysis radiocommunication signals is presented in the paper. The stand is designed for signals acquisition in wide spectrum and research a field of digital signal processing. Procedures used for simultaneous acquiring many frequency channels in selected wide band are described. The method of detection of direct sequence spread spectrum signals (DS SS) which power spectral density is lower than...
-
Surrogate-assisted EM-driven miniaturization of wideband microwave couplers by means of co-simulation low-fidelity models
PublicationThis article proposes a methodology for rapid design optimization of miniaturized wideband couplers. More specifically, a class of circuits is considered, in which conventional transmission lines are replaced by their abbreviated counterparts referred to as slow-wave compact cells. Our focus is on explicit reduction of the structure size as well as on reducing the CPU cost of the design process. For the sake of computational feasibility,...
-
A Goal-Oriented Error Estimator for Reduced Basis Method Modeling of Microwave Devices
PublicationThis letter proposes a novel a-posteriori error estimator suitable for the reduced order modeling of microwave circuits. Unlike the existing error estimators based on impedance function residuals, the new one exploits the residual error associated with the computation of the scattering matrix. The estimator can be effectively used in the Reduced Basis Method (RBM) to automatically generate reduced-order models. The results of numerical...