Filters
total: 1393
-
Catalog
displaying 1000 best results Help
Search results for: unmanned maritime vehicles
-
Comparing combined gas tubrine/steam turbine and marine low speed piston engine/steam turbine systems in naval applications
PublicationPorównano układy napędowe okrętowe kombinowane turbina gazowa- turbina parowa oraz spalinowy okrętowy silnik tłokowy wolnoobrotowy - turbina parowa. Porównywano moce oraz zużycie paliwa oraz parametry pary świeżej układu turbiny parowej.
-
Exhaust gas temperature measurements in diagnostic examination of naval gas turbine engines. Part II. Unsteady processes
PublicationThe second part of the article presents the results of operating diagnostic tests of a two- and three-shaft engine with a separate power turbine during the start-up and acceleration of the rotor units. Attention was paid to key importance of the correctness of operation of the automatic engine load control system, the input for which, among other signals, is the rate of increase of the exhaust gas flow temperature. The article...
-
Exhaust gas temperature measurements in diagnostic examination of naval gas turbine engines. Part III. Diagnostic and operating tolerances
PublicationThe third part of the article presents a method for detecting failures of the automatic engine control system with the aid of an exhaust gas temperature setter, specially designed and machined for this purpose. It also presents a procedure of identifying the operating tolerances and determining the diagnostic tolerances for the exhaust gas temperature recorded in the naval turbine engine during the start-up and acceleration processes....
-
Life tests of a rotary single-stage magnetic-fluid seal for shipbuilding applications
PublicationUse of the magnetic fluid seal technology in water is much more difficult technological problem in comparisonto gas or vacuum environment. Some seals constructed up to time been are designed as hybrid, two stagesealing structures with shields or mechanical seals used as protection measures to the magnetic fluid seal.Anyway, there is always problem with immediate contact between magnetic fluid and the environmentalliquid. In the...
-
Operating and economical conditions of cooling water control for marine steam turbines condensers
PublicationW pracy dokonano analizy ekonomicznej i eksploatacyjnej sterowania pracą pomp wody chłodzącej skraplacze turbin okrętowych. Wzięto pod uwagę cechy konstrukcyjne pomp wody chłodzącej skraplacze główne i najnowsze wyniki badań dla takich pomp w zastosowaniach lądowych. Uwagę skupiono przede wszystkim na turbinowych parowych siłowniach okrętowych.
-
EXHAUST GAS TEMPERATURE MEASUREMENTS IN DIAGNOSTICS OF TURBOCHARGED MARINE INTERNAL COMBUSTION ENGINES PART II DYNAMIC MEASUREMENTS
PublicationThe second part of the article describes the technology of marine engine diagnostics making use of dynamic measurements of the exhaust gas temperature. Little-known achievements of Prof. S. Rutkowski of the Naval College in Gdynia (now: Polish Naval Academy) in this area are presented. A novel approach is proposed which consists in the use of the measured exhaust gas temperature dynamics for qualitative and quantitative assessment...
-
Operation evaluation method for marine turbine combustion engines in terms of energetics
PublicationAn evaluation proposal (quantitative determination) of an y combustion turbine engine operation has been presented , wherein the impact energy occurs at a given time due to Energy conversion. The fact has been taken into account that in this type of internal combustion engines the energy conversion occurs first in the combustion chambers and in the spaces between the blade of the turbine engine. It was assumed that in the combustion...
-
On power stream in motor or drive system
PublicationIn a motor or in a drive system the quantity of power increases in the direction opposite to the direction of power flow. Energy losses and energy efficiency of a motor or a drive system must be presented as functions of physical quantities independent of losses. Such quantities are speed and load. But the picture of power stream in a motor or in a drive system is presented in the literature in the form of traditional Sankey...
-
Design of OFDM-based radio communication systems for coast-to-sea and coast-to-air propagation environments
PublicationIn the paper the study of radio communication system design process for systems based on OFDM transmission is considered. The signal propagation model for 1.4 GHz frequency band is discussed, and the study of signal propagation characteristics, important from the point of view of OFDM system design, is presented. The methodology of OFDM interface design is proposed and some characteristics of the OFDM-based radio communication...
-
Bead-on-plate welding on S235JR steel by underwater local dry chamber process
PublicationThe article presents the results of the effect of parameters of underwater local dry chamber welding on the properties of padding welds. The effect of heat input and the type of shielding gas on the structure and hardness of welds was established. the functions for estimating the maximum hardness of the heat affected zone have been also elaborated.
-
Robust Model Predictive Control for Autonomous Underwater Vehicle–Manipulator System with Fuzzy Compensator
PublicationThis paper proposes an improved Model Predictive Control (MPC) approach including a fuzzy compensator in order totrack desired trajectories of autonomous Underwater Vehicle Manipulator Systems (UVMS). The tracking performancecan be affected by robot dynamical model uncertainties and applied external disturbances. Nevertheless, the MPCas a known proficient nonlinear control approach should be improved by the...
-
Daily Radiation Budget of the Baltic Sea Surface from Satellite Data
Publication -
Practical Applicability and Preliminary Results of the Baltic Environmental Satellite Remote Sensing System (Satbałtyk)
Publication -
Use of Satellite Data in Monitoring of Hydrophysical Parameters of the Baltic Sea Environment
Publication -
MSIS Image Postioning in Port Areas with the Aid of Comparative Navigation Methods
Publication -
Advanced coating of interior of tanks for rising environmental safety - novel applications of polyurethanes
Publication -
Advanced coating of Tank Interior as means of Rising Environmental Safety of Tankers/RIM technology
Publication -
Analysis of faecal bacteria isolated from air and seawater samples following an emergency sewage discharge into the Gulf of Gdansk in 2018 — preliminary study
Publication -
CFD and FEM model of an underwater vehicle propeller
PublicationDuring the project execution of design and optimization the Remotely Operated Vehicle (ROV) research on its propulsion has been carried out. The entire project was supported by CFD and FEM calculations, which taking into account the characteristics of underwater vehicle. One of the tasks was to optimize the semi-open duct for horizontal propellers, which provided propulsion and controllability in horizontal plane. In order to...
-
Computational simulation of motion of a rescue module during its launching from ship at rough sea
PublicationThis paper is a continuation of the work titled : “A comp utational model for simulation of motion of rescue module during its launching from stern ramp of a ship at rough sea”. It presents results of computer simulations of motion of a rescue module with embarked persons during its launching on rollers along stern ramp of a ship at rough sea. The simulations were conducted for a selected ship fitted with a launching ramp , for...
-
A numerical model to simulate the motion of a lifesaving module during its launching from the ship’s stern ramp
PublicationThe article presents a numerical model of object motion in six degrees of freedom (DoF) which is intended to be used to simulate 3D motion of a lifesaving module during its launching from a ship using a stern ramp in rough sea. The model, of relatively high complexity, takes into account both the motion of the ship on water in changing sea conditions, and the relative motion of the ramp with respect to the ship. The motion of the...
-
Effective method for determining environmental loads on supporting structures for offshore wind turbines
PublicationThis paper presents a description of an effective method for determining loads due to waves and current acting on the supporting structures of the offshore wind turbines. This method is dedicated to the structures consisting of the cylindrical or conical elements as well as (truncates) pyramids of polygon with a large number of sides (8 or more). The presented computational method is based on the Morison equation, which was originally...
-
STUDY OF SEASONAL ACOUSTIC PROPERTIES OF SEA WATER IN SELECTED WATERS OF THE SOUTHERN BALTIC
PublicationClimate Research of the globe is a current task, in particular to confirm the general hypothesis of global warming associated with an increase in average temperature. The sea acoustic climate is derived from the concept of climate and refers to the conditions of propagation of acoustic waves in a particular basin. In this paper, the results of systematic measurements of temperature, salinity and velocity distributions of sound...
-
Capillary pumped loop as a tool for collecting large heat fluxes from electronic devices on warships
PublicationThe combat potential of future warships will be directly related to the use of modern electronic devices being parts of advanced systems, such as, for instance, radar systems, fire aiming systems, fire detection systems, electric drive systems, and even electronic and radio-electronic weaponry, railguns and lasers, installed on these warships. The capacity and functionality of these devices is continually increasing, at decreasing...
-
Composite GFRP U-shaped footbridge
PublicationThe paper presents proposals for the use of glass fiber reinforced polymer composites for the construction of engineering objects, known and commonly used in the shipbuilding industry. An example of a pedestrian footbridge was used in this case, which, despite the considerable thickness of the structural material, was made using infusion technology in one production cycle. The designed and produced footbridge span is durable, dynamically...
-
Calculation method for flow boiling and flow condensation of R134a and R1234yf in conventional and small diameter channels
PublicationThe paper presents the results of calculations performed using the authors’ model to predict the heat transfer coefficient during flow boiling for two refrigerants R134a and R1234yf. The experimental data from various past studies have been collected and the calculations have been conducted for the full range of quality variation and a wide range of mass velocity. The aim of the study was to test the sensitivity of the in-house...
-
The influence of water and mineral oil on volumetric losses in a hydraulic motor
PublicationIn this paper volumetric losses in hydraulic motor supplied with water and mineral oil (two liquids having significantly different viscosity and lubricating properties) are described and comparison. The experimental tests were conducted using an innovative hydraulic satellite motor, that is dedicated to work with different liquid, including water. The sources of leaks in this motor are characterized and described also. On this...
-
Underwater Wet Repair Welding of API 5L X65M Pipeline Steel
PublicationThis paper presents results of the research of effect of polymer insulation of pipeline made of API 5L X65M steel as well as underwater wet welding parameters on properties of joints made by covered electrodes. Effect of heat input on structure and hardness of joints during repair of underwater pipeline was analyzed. Welding defects like microcracks, micro-lacks of fusion, slag inclusions, as well as HAZ hardness increase over...
-
The effect of fishing basin construction on the behaviour of a footbrdge over the port channel
PublicationThe paper analyses possible causes of failure of the rotating footbridge over the Ustka port channel. In July, 2015, strange behaviour of this object was observed in the form of excessive vibrations of bridge platform suspension rods, with the accompanying acoustic effects. A preliminary geotechnical analysis has revealed that this destructive effect was caused by the nearby construction works, namely construction of a fishing...
-
FAILURE OF MAGNETIC FLUID SEALS OPERATING IN WATER: PRELIMINARY CONCLUSIONS
PublicationThe article analyses properties of magnetic fluid seals installed in rotary sealing no des which operate in the utility water environment. Seals of this type have been examined as a possible solution to the problem with ship manoeuvring propulsion sealing. The present analysis bases on laboratory durability tests of magnetic fluid seals expo sed to long - term utility water loads, at different water pressures and shaft revolutions....
-
A method for preliminary estimation of the length of midship body block to be inserted during ship’s conversion
PublicationThe paper presents a method for preliminary estimation of the length of the midship body block, which inserted in the original hull, increases the deadweight of the ship in line with a required quantity. The method may be useful for establishing the scope of conversion to better adjust the ship for transportation tasks. The problem is formulated by using a mathematical model so selected that its solution, under set of assumptions,...
-
VARIANT DESIGNING IN the PRELIMINARY SMALL SHIP DESIGN PROCESS
PublicationShip designing is a complex process, as the ship itself is a complex, technical multi-level object which operates in the air/water boundary environment and is exposed to the action of many different external and internal factors resulting from the adopted technical solutions, type of operation, and environmental conditions. A traditional ship design process consists of a series of subsequent multistage iterations, which gradually...
-
Possibilities of heat transfer augmentation in heat exchangers with minichannels for marine applications
PublicationIn the paper, new trends in development of microchannel heat exchangers are presented. The exchangers developed in this way can be applied in marine applications. Main attention was focused on heat exchangers design with reduced size of passages namely based on microchannels. In our opinion future development of high power heat exchangers will be based on networks micro heat exchangers.
-
Modelling and Simulation of a New Variable Stiffness Holder for Milling of Flexible Details
PublicationModern industry expectations in terms of milling operations often demand the milling of the flexible details by using slender ball-end tools. This is a difficult task because of possible vibration occurrence. Due to existence of certain conditions (small depths of cutting, regeneration phenomena), cutting process may become unstable and self-excited chatter vibration may appear. Frequency of the chatter vibration is close to dominant...
-
Strength analysis of a large-size supporting structure for an offshore wind turbine
PublicationThe offshore wind power industry is the branch of electric energy production from renewable sources which is most intensively developed in EU countries. At present, there is a tendency to install larger-power wind turbines at larger distances from the seashore, on relatively deep waters. Consequently, technological solutions for new supporting structures intended for deeper water regions are undergoing rapid development now. Various...
-
A DISCRETE-CONTINUOUS METHOD OF MECHANICAL SYSTEM MODELLING
PublicationThe paper describes a discrete-continuous method of dynamic system modelling. The presented approach is hybrid in its nature, as it combines the advantages of spatial discretization methods with those of continuous system modelling methods. In the proposed method, a three-dimensional system is discretised in two directions only, with the third direction remaining continuous. The thus obtained discrete-continuous model is described...
-
Corrosion fatigue crack propagation rate characteristics for weldable ship and offshore steels with regard to the influence of loading frequency and seawater temperature
PublicationAfter Vosikovsky (1975), the corrosion fatigue crack growth rate (CFCGR) characteristics have been divided into three regions. The region-III rates are very close to mechanical fatigue crack growth rates. CFCGR formulae, including the long-crack length effect (in region I only), the loading frequency effect (in region II only), and the saltwater temperature effect, have been proposed. It has been assumed that CFCGR is proportional...
-
Implementing Simulationx in the Modelling of Marine Shafting Steady State Torsional Vibrations
Publication -
Influence of Fin’s Material Capabilities on the Propulsion System of Biomimetic Underwater Vehicle
Publication -
Parameters Identification of the Flexible Fin Kinematics Model Using Vision and Genetic Algorithms
Publication -
Optimization Model to Manage Ship Fuel Consumption and Navigation Time
Publication -
A concept of pusher - barge coupling device of two-segment ship for inland waterways and coastal service
PublicationW artykule przedstawiono założenia projektowe i koncepcję rozwiązania konstrukcyjnego oraz napędu i sterowania urządzenia sprzęgającego pchacz i barkę dwusegmentowego statku śródlądowego i przybrzeżnego. Zaprezentowane urządzenie umożliwia zarówno sztywne połączenie, jak i wzajemne kontrolowane wychylanie obu segmentów względem siebie, co w znacznym stopni zwiększa manewrowość, a tym samym bezpieczeństwo żeglugi, zwłaszcza na wąskich...
-
Selected problems of technological preparation of production of a two-segment passenger inland waterways ship of a combined structure
PublicationPrzystępując do opracowania założeń do ''Ramowej technologii budowy statku rzecznego'', którego projekt powstaje w ramach zadania INCOWATRANS natknięto się na szereg problemów wynikających z odmienności i prototypowości analizowanego statku. Statek rzeczny to składajacy się z dwóch autonomicznych jednostek zespół pływający. Konstrukcja każdej z wymienionych jednostek jest konstrukcją mieszaną tj. składa się z części o konstrukcji...
-
Anchoring and mooring equipment for a two-segment inland waterways ship
PublicationW artykule dokonano przeglądu i analizy wyposażenia kotwiczno-cumowniczego współczesnych statków śródlądowych. Przedstawiono także propozycję takiego wyposażenia dla segmentowego statku pasażerskiego wraz z doborem i rozmieszczeniem na pokładzie poszczególnych urządzeń.
-
Design concepts of propulsion and steering system for hotel unit of two-segment inland waterways ship
PublicationW artykule przedstawiono założenia projektowe i dwa rozwiązania koncepcyjne napędu i sterowania barki hotelowej, stanowiącej część dwusegmentowego statku śródlądowego i przybrzeżnego. Obydwa rozwiązania oparto na zastosowaniu dziobowego śrubosteru małej mocy, ze śrubą stałą umieszczoną w dyszy obrotowej. W jednym z rozwiązań śruba napędzana jest silnikiem hydraulicznym, zaś w drugim - silnikiem elektrycznym. Mechanizm obrotu kolumny...
-
Fatigue life tests of steel laser-welded sandwich structures
PublicationW publikacji zaprezentowano rezultaty systematycznych badań trwałości zmęczeniowej elementarnych połączeń wykonanych techniką spawania laserowego dla różnych wariantów geometrii złącz. Pokazano uzyskane wyniki i ich aproksymację, porównano uzyskane rezultaty dla różnych geometrii.
-
A method for predicting main propulsion power for inland waterways push trains
PublicationPraca zawiera założenia teoretyczne i model matematyczny metody służącej do wyznaczania wstępnej, przybliżonej prognozy wielkości zapotrzebowanej mocy napędu głównego śródlądowego zestawu pchanego.
-
A model of occurrence of the situations endangering inland waterways passanger ships and the environment
PublicationZaproponowano czterostanowy semimarkowski model pojawiania się sytuacji zagrażających pasażerskim statkom śródlądowym. Model ten został opracowany w formie semimarkowskiego procesu dyskretnego w stanach i ciągłego w czasie, którego wartościami są rodzaje stanów, interpretowanych jako sytuacje: normalna, skomplikowana, niebezpieczna oraz awaryjna. Zobrazowano przykładową realizację procesu zmian sytuacji, jakie mogą pojawić się...
-
Tests of local strains in steel laser - welded sandwich structure
PublicationW publikacji zaprezentowano rezultaty badań odkształceń w strefie spoiny laserowej konstrukcji sandwich. Pokazano obiekt badań, metodykę i oprzyrządowanie oraz proces rejestracji. Przedstawiono uzyskane wyniki i wnioski z nich wypływające.
-
Two design concepts of power plant for an inland waterways passenger ship intended for operating on Berlin-Kaliningrad route
PublicationArtykuł przedstawia dwa rozwiązania siłowni dwuczłonowego, śródlądowego statku pasażerskiego przeznaczonego na trasę Berlin-Kaliningrad. Przedstawiono projekty wstępne siłowni głównej umieszczonej na pchaczu oraz omówiono wymagania odnośnie siłowni pomocniczej umieszczonej w barce.