Search
Filters
total: 964
filtered: 500
Search results for: TRIPLEX-TUBE
-
Thermal and economic investigation of straight and U-bend double tube heat exchanger with coiled wire turbulator
PublicationExperimental research has been carried out for four individual heat exchanger constructions, i.e., plain double tube, turbulized double tube, plain U-bend and U-bend with turbulator. Tests were made for the water-water system. The study covered a wide measuring range, i.e., Re = 800–9000 – on the shell side, for a constant cold water temperature of 9 ◦C and hot water of 50 ◦C. The heat exchangers were made from copper tubes with...
-
Design of a SiC based triple active bridge ceil for a multi-megawatt DC-DC converter
PublicationThe paper describes the design methodology of a novel Triple Active Bridge cell used as the building block for modular DC-DC converters. The intended application is for Medium Voltage Direct Current grids, such as the DC collector for offshore wind farms. The latest generation of SiC MOSFET semiconductors is utilized to operate in the medium frequency range while optimizing the efficiency. The dimensioning of the main cell components,...
-
Singlet and triplet excited states of a series of BODIPY dyes as calculated by TDDFT and DLPNO-STEOM-CCSD methods
PublicationThe singlet and triplet excited states of three iodine substituted BODIPY dyes differing by their substituent (-phenyl, -phenylOH and -phenylNO2) at the meso position of the BODIPY core (BOD) are investigated by (TDA)-TDDFT and DLPNO-STEOM-CCSD calculations. An assessment of hybrid (B3LYP and MN15) and double hybrid (SOS-PBE-QIDH and SOS-ωPBEPP86) exchange-correlation functionals is performed with respect to the DLPNO-STEOM-CCSD...
-
Experimental investigation of thermal energy storage in shell-and-multi-tube unit with nano-enhanced phase change material
PublicationThis paper deals with thermal energy storage with use of nanoparticle enhanced phase change material in shell-and-multitube unit. The experiments are conducted under atmospheric pressure. Paraffin wax and two different fatty acids are used as base phase change material. Graphite and multi-walled carbon nanotubes serve as nanoparticles. Graphite nanoparticles are tested at the concentrations of 0.1%, 1% and 5% by weight, while multi-walled...
-
Efektywność skrępowania betonu w grubościennych słupach typu Concrete-Filled Steel Tube o przekroju kołowym
PublicationW słupach typu CFST w stanie granicznym dochodzi do zwiększenia wytrzymałości betonu rdzenia na skutek jego skrępowania. Zaistnienie tego zjawiska zależy od wielu czynników. Jednym z najważniejszych z nich jest sztywność obwodowa płaszcza stalowego. Jej wpływ na efektywność wzrostu wytrzymałości betonu rdzenia przebadano eksperymentalnie na grupie 48 grubościennych słupów CFST. Wykazano, że nadmierne zwiększanie grubości płaszcza...
-
Fiberoptic intubation or video tube for trauma patient intubation—which method to choose? Randomized crossover manikin trial
Publication -
Application of Dispersive Liquid-Liquid Microextraction in Narrow-Bore Tube for Preconcentration and Spectrophotometric Determination of Cadmium in Aqueous Samples
Publication -
Induction Motor Bearings Diagnostic Using MCSA and Normalized Tripple Covariance
PublicationDiagnosis of induction motors, conducted remotely by measuring and analyzing the supply current is attractive with the lack of access to the engine. So far there is no solution, based on analysis of current, the credibility of which allow use in industry. Statistics of IM bearing failures of induction motors indicate, that they constitute more than 40% of IM damage, therefore bearing diagnosis is so important. The article provides...
-
Influence of iron content on water uptake and charge transport in BaCe0.6Zr0.2Y0.2−xFexO3−δ triple-conducting oxides
PublicationIn this work, we studied the BaCe0.6Zr0.2Y0.2−xFexO3−δ system which belongs to the triple-conducting oxides (TCOs) group. The electrochemical properties of BaCe0.6Zr0.2Y0.2−xFexO3−δ were investigated using electrochemical impedance spectroscopy (EIS) and the water uptake was analyzed using thermogravimetry (TG). All investigated materials exhibited water uptake, with proton concentration increasing with decreasing iron content....
-
Rola parków naukowo-technologicznych w modelu triple helix na przykładzie parków Polski Wschodniej
PublicationCelem artykułu jest omówienie roli parków naukowo-technologicznych w modelu triple helix, zarówno w aspekcie teoretycznym, jak i w oparciu o przeprowadzone badania empiryczne. Autorki zaprezentowały wyniki badańdotyczących powiązań wybranych parkówz pozostałymi grupami aktorów wyróżnionymi w modelu triple helix, ze szczególnym uwzględnieniem instytucji B+R, władz publicznych oraz innych instytucji pośredniczących. Badania przeprowadzono...
-
Modelling of flow boiling process in small diameter tubes.
PublicationW pracy zastosowano standardową korelację wrzenia w przepływie (wyprowadzoną dla rur o konwencjonalnych wymiarach) do przypadków wrzenia w rurach o małych średnicach. Porównanie wyników obliczeń z danymi literaturowymi wykazało nieużyteczność tej korelacji. Wykazano zatem potrzebę prowadzenia badań podstawowych celem uzyskania korelacji pozwalającej umiejętnie przewidywać warunki wymiany ciepła w kanałach o małych średnicach.
-
Flow boiling of oil-refrigerant mixtures in smooth tubes
PublicationPrzedstawiono wyniki badań współczynnika przejmowania ciepła i spadku ciśnienia podczas wrzenia czynników R 22, R 134a i R 407C i ich mieszanin z olejem w rurach gładkich. Opisano procedurę badawczą. Udział masowy oleju w mieszaninie z czynnikiem wynosił 0,1% i 5%. Zaobserwowano negatywny wpływ obecności środka smarnego we wrzącym czynniku chłodniczym.
-
Experimental investigations of R22 flow boiling in enhanced tubes.
PublicationPrzedstawiono wyniki badań eksperymentalnych wrzenia R22 podczas wrzenia w przepływie wewnątrz rur o rozwiniętej powierzchni przejmowania ciepła: miedzianej rury niskożebrowanej wewnętrznie, stalowej rury formowanej śrubowo oraz stalowej rury z pokryciem porowatym. Przeprowadzono także badania na dwóch rurach gładkich, o średnicy odpowiadającej maksymalnej średnicy wewnętrznej rur o rozwiniętej powierzchni. Średnie wartości...
-
Korozja rur ciepłowniczych = Heat water tubes corrosion
PublicationZbadano uszkodzenia korozyjne instalacji ciepłowniczej w aspekcie jakości rur zgrzewanych i korozyjności wody sieciowej. Rury przewodowe ze stali niskowęglowej zostały zniszczone przez korozję wżerową/podosadową zlokalizowaną w obszarze połączenia zgrzewanego wskutek nieodpowiedniej jakości wody.
-
Corrosion of evaporator tubes in low emission steam boilers
PublicationPurpose of this paper is to reveal the mechanisms of corrosion processes of outer surfaces of low-emission steam boiler evaporator tubes. Examinations were performed to find the reasons of different corrosion susceptibility of tubes situated at combustion chamber on various levels. Examinations were conducted on several segments of 57 x 5.0 mm evaporator tubes made of 16M (16Mo3) steel grade. Segments were taken from level of...
-
Dynamics of Field Line Mappings in Magnetic Flux Tubes
PublicationWe study the topological constraints on the dynamics of magnetic field lines in flux tubes. Our approach is based on the application of the topological invariant: fixed point index. We consider periodic flux tubes and find various restrictions on the field lines that come from the sequence of fixed point indices of iterations. We also analyze the case of a tube with a cylindrical obstacle, deducing some special dynamical properties...
-
Burnout Investigation of Small Diameter Tubes Immersed in Nanofluids
PublicationThis paper deals with research into pool boiling critical heat flux (CHF) of water–Al2O3, water–TiO2 and water–Cu nanofluids on horizontal stainless steel tubes. The experiments were conducted under atmospheric pressure. Nanoparticles were tested at concentrations of 0.001%, 0.01%, 0.1% and 1% by weight. Ultrasonic vibration was used in order to stabilize the dispersion of the nanoparticles. Although dispersants were not used to...
-
Stark effect of atomic helium second triplet series in electric fields up to 1600 kV cm−1
Publication -
Heat transfer and pressure drop during flow boiling of pure efrigerants and refrigerant/oil mixtures in tube with porous coating
PublicationW pracy przedstawiono wpływ powłoki porowatej na średni współczynnik przejmowania ciepła oraz opory przepływu podczas wrzenia wybranych czynników chłodniczych wewnątrz poziomych rurek. Badania przeprowadzono dla techniczne czystych czynników chłodniczychR22, R134a i R407C oraz ich mieszanin z olejem poliestrowym 1% i 5% wrzących w rurkach wykonanych ze stali nierdzewnej, o wewnętrznej powierzchni gładkiej oraz z metaliczną powłoką...
-
Genetic and biochemical determinants of serum concentrations of monocyte chemoattractant protein-1, a potential neural tube defect risk factor
Publication -
Comparison of disk and tube methods for estimation of biostatic properties of polyurethanes based on synthetic poly[(R,S)-3-hydroxybutyrate
PublicationThe influence of novel aliphatic polyurethanes on growth of Staphyloccocus aureus (SA)in the around of polymer samples has been estimated by disk method. It was staed that the growth of SA was inhibited.The influence of polyurethanes on planctonic Staphyloccocus aureus was also pefrormed by tube method. In this test the slight decrease of bacteria concentration was noticed.
-
Multi-region fuzzy logic controller with local PID controllers for U-tube steam generator in nuclear power plant
PublicationIn the paper, analysis of multi-region fuzzy logic controller with local PID controllers for steam generator of pressurized water reactor (PWR) working in wide range of thermal power changes is presented. The U-tube steam generator has a nonlinear dynamics depending on thermal power transferred from coolant of the primary loop of the PWR plant. Control of water level in the steam generator conducted by a traditional PID controller...
-
ASSESSING THE POTENTIAL REPLACEMENT OF MINERAL OIL WITH ENVIRONMENTALLY ACCEPTABLE LUBRICANTS IN A STERN TUBE BEARING: AN EXPERIMENTAL ANALYSIS OF BEARING PERFORMANCE
PublicationT his study compares the performance of a plain bearing, with a similar structure to a tail shaft stern bearing, lubricated with either mineral oil or an environmentally acceptable lubricant (EAL). The main characteristic of the bearing is its length/diameter ratio of <1. Measurements are carried out with the bearing operating under loads from 0.5 to 1 MPa and seven speeds ranging from 1 to 11 rev/s. The bearing lubricated...
-
High Efficiency Dual-Active-Bridge Converter with Triple-Phase-Shift Control for Battery Charger of Electric Vehicles
PublicationAn optimal modulation scheme with triple-phase-shift (TPS) control could increase the efficiency in the entire load range for a dual-active-bridge (DAB) converter under wide output voltage range conditions. Therefore, this study proposes a convergent approach to TPS mode selection, coupled with an optimal modulation scheme, ensuring the circuit’s efficiency over the entire range in the realm of a high-power and high-efficiency...
-
Co-free triple perovskite La1.5Ba1.5Cu3O7±δ as a promising air electrode material for solid oxide fuel cells
Publication -
Improved correlation for modelling of boiling processes in small diameter tubes.
PublicationW pracy przedstawiono rozważania na temat wrzenia w przepływie dwufazowym w kanałach o małej średnicy. Modyfikacji uległa korelacja zapostulowana wcześniej przez Mikielewicz i inni, poprzez wprowadzenie efektów związanych z napięciem powierzchniowym, także liczba konwekcyjna została poprawiona. Zastosowanie korelacji jest bardzo proste z uwagi na jej analityczną postać, co jest jej podstawową zaletą. Porównanie z danymi eksperymentalnymi...
-
Assessment of structural changes in IN-519 cast steel reformer tubes.
PublicationPrzedstawiono zmiany struktury rur katalitycznych ze staliwa austenitycznego IN-519 po długotrwałej eksploatacji w reformerze metanu.
-
Assessment of evaporator tubes corrosion in low-emission steam boilers
PublicationW artykule przedstawiono wyniki badań rur ekranowych(16Mo3) kotła niskoemisyjnego po jednym roku i dwóch latach eksploatacji. Powierzchnie rur pokryte zostały warstwami natryskiwanymi cieplne - pojedynczą ze stopu 70%Ni 30%Cr i podwójną Ni-30Cr /Al2O3. Rury bez powłok natryskiwanych wykazywały pocienienie ze względu na działanie korozji siarkowej oraz korozyjnego oddziaływania warstwy stopionych soli. Pojedyncza warstwa 70%Ni 30%Cr...
-
Comparative study of flow condensation in conventional and small diameter tubes
PublicationFlow boiling and flow condensation are often regarded as two opposite or symetrical phenomena. Their description however with a single correlation has yet to be suggested.In the case of flow boiling in minichannels there is mostly encountered the annular flow structure, where the buble generetion is not present. Similar picture holds for the case of inside tube condensation, where annular flow structure predominates. In such case...
-
High temperature corrosion of evaporator tubes with thermal sprayed coatings
PublicationDegradation examinations of outer surface of low-emission steam boiler evaporator tubes are presented in the paper. Metallographic evaluation of scale morphology, its micro sites chemical composition analysis and distribution of elements on cross sections have been performed. Water-wall tubes were exposed in steam boiler for up to two years period. Common tubes made of 16Mo3 steel suffered sulphide and molten salts corrosions....
-
Comparative study of flow condensation in conventional and small diameter tubes
PublicationFlow boiling and flow condensation are often regarded as two opposite or symmetrical phenomena, however their description with a single correlation has yet to be suggested. In the case of flow boiling in minichannels there is mostly encountered the annular flow structure, where the bubble generation is not present. Similar picture holds for the case of inside tube condensation, where annular flow structure predominates. In such...
-
Comparative study of flow condensation in conventional and small diameter tubes
PublicationIn the paper a method developed earlier by the first author is applied to calculations of heat transfer coefficient for inside tube condensation. The method has been verified using experimental data from literature on several fluids in different microchannels and compared to three well established correlations.
-
Evaluation of reformer tubes degradation after long term operation
PublicationPurpose of this paper is to show the effect of long-term service at elevated temperatures on microstructural changes of cast steel reformer tubes made of the alloy IN-519 (24%Cr, 24%Ni, Nb). The relationship between mechanical properties and microstructure degradation is discussed. Investigations were performed on five tubes taken from ammonia reformer furnace. Tubes worked at temperature of 880C and 3,2 MPa pressure. The operation...
-
One-tube cell lysis and DNA extraction procedure for PCR based detection of Mycobacterium ulcerans in aquatic insects, molluscs and fish.
PublicationMycobacterium ulcerans jest bakterią wywołującą choroby skóry u ludzi i zwierząt. W trakcie prowadzonych badań opracowano prostą w wykonaniu metodę ekstrakcji DNA Mycobacterium ulcerans z próbek środowiskowych oraz klinicznych. Opracowana metoda izolacji DNA może być przydatna w badaniu źródeł infekcji oraz dróg szerzenia się Mycobacterium ulcerans.
-
The effect of pressure on heat transfer during pool boiling of water-Al2O3 and water-Cu nanofluids on stainless steel smooth tube
PublicationPrzedstawiono wyniki badań eksperymentalnych wrzenia nanocieczy woda-Al2O3 i woda-Cu o koncentracjach nanocząstek 0.01%, 0.1% oraz 1% przy ciśnieniu absolutnym 10 kPa, 100 kPa oraz 200k Pa.
-
Assessment of cross compatibility of pear (Pyrus communis L.) cultivars on the basis of pollen tube observations and analysis of the S-RNase gene
Publication -
Experimental research on water lubricated marine stern tube bearings in conditions of improper lubrication and cooling causing rapid bush wear
PublicationWater lubricated bearings are popular in sliding bearings of marine propeller shafts, turbines and pump shafts. Such popularity is partly due to their simple construction which also means a relatively affordable price. In practical experience one may also observe cases of rapid wear or even malfunctions of this bearings, some of which may be caused by insufficient flow of lubricant leading to overheating. The conducted...
-
Identification and characterization of the Indian Yellow dyestuff and its degradation products in historical oil paint tube by liquid chromatography mass spectrometry
PublicationAn analytical protocol for identification of dyes using reversed phase liquid chromatography-mass spectrometry with atmospheric pressure electrospray ionization (LC-ESI/MS) is presented. The developed method has been successfully applied in identification of euxanthic acid and euxanthone, the main components of the Indian Yellow dye in a historical oil paint tube produced by Richard Ain`es, a recognizable French company supplying...
-
Experimental and Computational Fluid Dynamics Studies on Straight and U-Bend Double Tube Heat Exchangers with Active and Passive Enhancement Methods
PublicationIn this work, the authors wanted to demonstrate the possibility to increase the heat transfer efficiency by using simple wire coil inserts to create turbulent flow in the boundary layer as well as air blowing into the annulus of the pipe. Experimental investigations were carried out for four heat exchanger constructions, i.e., plain double tube, turbulized double tube, plain U-bend double tube, U-tube with turbulator, plain double...
-
Environmentally acceptable lubricants (EAL) compared with a reference mineral oil as marine stern tube bearing lubricant – Experimental and theoretical investigations
PublicationThe purpose of this research is to indicate the potential differences in bearing characteristics resulting from the application of different lubricant types with the same viscosity grade. The effect of different environmentally acceptable lubricants (EALs) on hydrodynamic journal bearing properties is studied experimentally and compared to the properties obtained after lubrication with a reference mineral oil. The results of the...
-
A new construction of shell-and-tube heat exchanger with impinging jets and minichannels technologies for heat recovery from gases – experimental analysis
PublicationA dynamic development of technologies allowing waste heat utilization is observed in a correspondence with a pro-ecological approach of the zero waste idea. Such approach becomes the most demanding in the area of low-temperature was heat sources, especially gaseous media. Till now, they were usually not utilized due to unfavorable thermal conditions and high costs. Therefore, the zero waste approach directs research on techniques...
-
Experimental and theoretical study of a vertical tube in shell storage unit with biodegradable PCM for low temperature thermal energy storage applications
PublicationThis article presents the experimental investigations of the coconut oil-based TES module for HVAC applications in the ambient and-sub ambient temperature range. To properly study this problem modular experimental module and test loop were developed. Special attention has been paid to study the physical mechanism of the melting/solidification process for natural substance (coconut oil) which has perspectives to be used in thermal...
-
Weak antilocalization effect and triply degenerate state in Cu-doped CaAuAs
Publication -
Assessment of reformer tubes degradation during longterm service at elevated temperatures
Publication -
Investigation of R 22 and R 134a flow boiling in enhanced tubes
PublicationPrzedstawiono wyniki pomiarów współczynnika przejmowania ciepła i spadków ciśnienia podczas wrzenia w przepływie R22 oraz R134a. Do badań użyto dwie rurki o rozwiniętej wewnętrznej powierzchni, tj. rurkę śrubowo-formowaną i rurkę niskożebrowaną oraz dwie rurki gładkie, jako rurki referencyjne. Eksperymenty przeprowadzono przy temperaturze nasycenia ok. zero stopni Celsjusza i końcowym stopniu suchości ok. 0.7. Wyniki badań eksperymentalnych...
-
The effect of foliar fertilization on darkening of tuber flesh of selected potato cultivars
Publication -
High temperature corrosion of evaporator tubes in low-emission steam boilers
PublicationW artykule opisano zjawisko korozji wysokotemperaturowej rur ekranowych kotłów parowych niskoemisyjnych. Przeprowadzono badania rur po eksploatacji. Wykonano badania składu chemicznego zgorzelin. Stwierdzono, że główną przyczyną pocienienia rur na wyższych poziomach jest korozja siarkowa, natomiast na poziomach niższych oddziaływanie stopionych soli.
-
Pool boiling of nanofluids on rough and porous coated tubes: experimental and correlation
PublicationThe paper deals with pool boiling of water-Al2O3 and water- Cu nanofluids on rough and porous coated horizontal tubes. Commercially available stainless steel tubes having 10 mm outside diameter and 0.6 mm wall thickness were used to fabricate the test heater. The tube surface was roughed with emery paper 360 or polished with abrasive compound. Aluminium porous coatings of 0.15 mm thick with porosity of about 40% were produced by...
-
Method of evaluation of lubricating ability of lube oils and fuels in energetistic formulation
PublicationThe paper presents an interpretation of operation of a boundary layer of a lubricating medium. A model of the homogeneous Poisson process has been proposed to assess the deterioration process of the layer's operation. The assessment considers the original interpretation of operation of a boundary layer, as a lubricity measure of a boundary layer of any lubricant. In the submitted proposal the operation of a boundary layer is understood...
-
Failure of austenitic stainless steel tubes during steam generator operation
PublicationThe article presents the failure process of austenitic stainless steels used in power devices, such as heat exchangers, steam generators, in terms of local corrosion: pitting, stress and intergranular corrosion, paying particular attention to welded joints area. The effect of steel chemical composition, microstructure, welding process and work environment was analyzed. The second part of the article presents the results of the...