Filters
total: 5802
-
Catalog
displaying 1000 best results Help
Search results for: flow cytometry
-
Calculation method for flow boiling and flow condensation of R134a and R1234yf in conventional and small diameter channels
PublicationThe paper presents the results of calculations performed using the authors’ model to predict the heat transfer coefficient during flow boiling for two refrigerants R134a and R1234yf. The experimental data from various past studies have been collected and the calculations have been conducted for the full range of quality variation and a wide range of mass velocity. The aim of the study was to test the sensitivity of the in-house...
-
EHD Flow Measured by 2D PIV in a Narrow Electrostatic Precipitator with Longitudinally-to-flow Wire Electrode
PublicationIn this paper, results of the electrohydrodynamic (EHD) flow patterns in two narrow ESPs with longitudinally-to-flow wire electrode are presented. The influence of the ESP geometry on the EHD flow generated in the ESP was investigated. The results obtained from 2 dimensional (2D) Particle Image Velocimetry (PIV) showed similarities and differences of the particle flow in the wire-plate and wire-cylinder type ESP.
-
EXPERIMENTAL VERIFICATION OF THE METHOD OF FLOW BOILING AND FLOW CONDENSATION HEAT TRANSFER PREDICTION FOR SELECTED FLUIDS
PublicationIn the paper presented are the results of calculations using authors own model to predict heat transfer coefficient during flow boiling of different refrigerants. The experimental data from various research studies from literature were collected. Calculations were conducted for a full range of quality variation and a wide range of mass velocity. The aim of the study was to test the sensitivity of the in- house developed model....
-
Application of Feed Forward Neural Networks for Modeling of Heat Transfer Coefficient During Flow Condensation for Low and High Values of Saturation Temperatur
PublicationMost of the literature models for condensation heat transfer prediction are based on specific experimental parameters and are not general in nature for applications to fluids and non-experimental thermodynamic conditions. Nearly all correlations are created to predict data in normal HVAC conditions below 40°C. High temperature heat pumps operate at much higher parameters. This paper aims to create a general model for the calculation...
-
Optometry-Journal of the American Optometric Association
Journals -
Experimental validation of pressure drop models during flow boiling of R134a – effect of flow acceleration and entrainment
PublicationA crucial step to assure proficient work of power and process apparatus is their proper design. A wide array of those devices operates within boiling or condensation of the working fluid to benefit from high heat transfer rates. Two-phase flows are associated with high heat transfer coefficients because of the latent heat of evaporation and high turbulence level between the liquid and the solid surface. Predicting heat transfer...
-
Interaction Between Storm Water Conduit Flow and Overland Flow for Numerical Modelling of Urban Area Inundation
PublicationNowadays we can observe increasing frequency of inundations in cities. This makes accurate predicting of inundations more important than ever. Numerical modeling of this issue requires complex approach with simultaneous calculations of pipe flow and surface flow. In this paper, after a short review of known methods used for solving pipe and surface flow, we will try to answer the question if presented methods would be sufficiently...
-
Dryout in annular flow - theoretical analysis
PublicationW pracy zaprezentowano model kryzysu wrzenia w przepływie pierścieniowym, obowiązujący dla wysokich wartości stopnia suchości i stanowiący modyfikację wcześniejszej wersji modelu zaproponowanego przez Sedlera i Mikielewicza. Model ten uwzględnia bilans masy w filmie cieczowym i bilans masy dla kropel cieczy w rdzeniu przepływu oraz zawiera dodatkowy człon odpowiedzialny za odparowanie filmu na ściance kanału. Rozwiązanie układu...
-
On a comparison principle and the uniqueness of spectral flow
PublicationThe spectral flow is a well-known quantity in spectral theory that measures the variation of spectra about 0 along paths of selfadjoint Fredholm operators. The aim of this work is twofold. Firstly, we consider homotopy invariance properties of the spectral flow and establish a simple formula which comprises its classical homotopy invariance and yields a comparison theorem for the spectral flow under compact perturbations. We apply...
-
The Maslov index and the spectral flow—revisited
PublicationWe give an elementary proof of a celebrated theorem of Cappell, Lee and Miller which relates the Maslov index of a pair of paths of Lagrangian subspaces to the spectral flow of an associated path of self-adjoint first-order operators. We particularly pay attention to the continuity of the latter path of operators, where we consider the gap-metric on the set of all closed operators on a Hilbert space. Finally, we obtain from Cappell,...
-
QoS Extensions for Flow-Awareness Networks
PublicationThe paper contains a description and research results of the proposal for distributed QoS extensions for Flow-Based Networking. These QoS extensions let the network accept or reject flows based on current network load and QoS promises for each of the flows. Proposed solution consists of two distributed components, each of them performing in every node, measurement system and access control. The solution could be applied in any...
-
Practical aspects of Flow Thinning optimization
Publication -
Complexity of a classical flow restoration problem
Publication -
Isotropic damage in viscoplastic flow conditions
PublicationMechanika zniszczenia jest obecnie jedną z ważniejszych gałęzi mechaniki ciał stałych. Jest cały czas rozwijającą się dziedziną nauki, która znalazła swoje zastosowania w problemach inżynierskich. W artykule zaprezentowano podstawowe informacje na temat lepkoplastyczności i jej zastosowania, koncepcję mechanicznej reprezentacji zniszczenia przez zmienną D, koncepcję naprężeń efektywnych, równania opisujące zniszczenie oraz lepkoplastyczny...
-
Modelling of dryout process in an annular flow
PublicationW pracy pokazano teoretyczny model kryzysu wrzenia przy wysokich stopniach suchości, który jest modyfikacją modelu proponowanego wcześniej przez Sedlera i Mikielewicza. Model wysychania filmu cieczowego w przepływie pierścieniowym składa się z różniczkowych równań bilansu masy zapisanych dla filmu na ściance i kropel w rdzeniu przepływu. Rozwiązanie układu równań wymaga znajomości gęstości strumienia masy kropel wytrącających się...
-
MODELLING OF TRANSIENT FLOW IN STORM SEWERS
PublicationThe paper focuses on the assessment of second-order explicit numerical scheme for unsteady flows in sewers. In order to simulate the pressurized flow the 'Preissmann slot' concept is implemented. For simulation of the transcritical flow the original and improved McCormack scheme is used. The calculated results are compared with numerical solutions and laboratory measurements published in the technical literature. Moreover, the...
-
Outlet Flow Velocity In Circular Culvert
PublicationThe outlet flow velocity in the end section of the culvert barrel depends in most cases on the culvert geometry, including the barrel slope, as well as on upstream and downstream channel parameters. Flowing water can create pressure flow or free surface flow in the culvert barrel. In the case of an unsubmerged barrel outlet, the free-surface flow is more frequent than the full flow. Increased velocities can cause channel bed scour...
-
Flow Process Models for Pipeline Diagnosis
PublicationThis chapter examines the problem of modeling and parameterization of the transmission pipeline flow process. First, the base model for discrete time is presented, which is a reference for other developed models. Then, the diagonal approximation (AMDA) method is proposed, in which the tridiagonal sub-matrices of the recombination matrix are approximated by their diagonal counterparts, which allows for a simple determination of...
-
Modelling of heat transfer in flow boiling
PublicationW pracy przedstawiono zagadnienia związane z modelowaniem wrzenia w przepływie w kanałach o małej średnicy. Przedstawiono modyfikację rozwijanej przez autorów korelacji umożliwiającej wyznaczanie współczynnika przejmowania ciepła podczas wrzenia w przepływie.
-
Modelling of dryout process in annular flow
PublicationW pracy pokazano teoretyczny model kryzysu wrzenia przy wysokich stopniach suchości, który jest modyfikacją modelu proponowanego wcześniej przez Sedlera i Mikielewicza. Model wysychania filmu cieczowego w przepływie pierścieniowym składa się z różniczkowych równań bilansu masy zapisanych dla filmu na ściance i kropel w rdzeniu przepływu. Rozwiązanie układu równań wymaga znajomości gęstości strumienia masy kropel wytrącających się...
-
The wastewater flow through trickling filters.
PublicationFiltry zraszane projektowane są głównie w oparciu o wytyczne techniczne. W pracy zaproponowano metodę o charakterze strukturalnym. Pokazano sposób określania miarodajnego czasu przebywania cieczy w układzie i powiązania go z kinetyczną charakterystyką procesu oczyszczania ścieków.
-
Flow Control Algorithm for UMTS HSDPA
PublicationHSDPA (High Speed Downlink Packet Access) jest istotnym etapem ewolucji systemu UMTS. Pozwala na transmisję do użytkownika z prędkością dochodzącą do 14.4 Mbit/s; aby to umożliwić, wprowadzono w wersji 5 UMTS szereg nowych mechanizmów w warstwie fizycznej oraz MAC. W tej pracy przedstawiono szczegółową analizę jednego z nowych mechanizmów - algorytmu kontroli natężenia ruchu między MAC-hs i MAC-d. Zaproponowano nowy, efektywny...
-
Some solutions of unsteady flow in bioreactor.
PublicationCzas regeneracji chrząstki stawowej po urazie jest długotrwały. Czasem tkanka nie regeneruje się. Dlatego też przeszczepy odgrywają bardzo ważną rolę. Najlepsze efekty hodowli tkanek zaobserwowano w bioreaktorach wykonujących ruch obrotowy i zapewniających nieustalony charakter przepływu ciecy odżywczej. Dlatego tematem niniejszego artykułu są pewne metody i rozwiązania nieustalonego przepływu cieczy w warstwie przyściennej hodowanej...
-
Application of tomography to granular silo flow.
PublicationPublikacja zawiera opis wyników badań doświadczalnych nad efektami dynamicznymi podczs opróżniania silosów z zastosowaniem tomografii pojemnościowej.
-
Comparison of the performance of direct current atmospheric pressure glow microdischarges operated between a small sized flowing liquid cathode and miniature argon or helium flow microjets
Publication -
Non-isothermal effects in a common method for calculation of heat transfer coefficient in flow boiling and flow condensation in minichannels
PublicationW pracy przestawiono efekty nieizotermiczne w metodzie wyznaczania współczynnika przejmowania ciepła podczas wrzenia w przepływie oraz kondensacji w przepływie w minikanałach. Wyniki obliczeń porównano z badaniami eksperymentalnymi z literatury, uzyskując dobrą zgodność.
-
A common method for calculation of flow boiling and flow condensation heat transfer coefficients in minichannels with account of nonadiabatic effects
PublicationW pracy przedstawiono metodę ogólną wyznaczania współczynników przejmowania ciepła podczas wrzenia w przepływie i kondensacji w przepływie w minikanałach z uwzględnieniem efektu nieadiabatycznego. Uwzględnia ona wpływ modyfikacji naprężeń stycznych na granicy ciecz-para na wymianę ciepła.
-
Marek Krawczuk prof. dr hab. inż.
PeopleScientific background 1987 - graduated Gdansk Univeristy of Technology, Faculty of Machine Design 1991 - PhD - Institute of Fluid Flow Machinery Gdansk 1995 - DSc - Institute of Fluid Flow Machinery Gdansk 2003 - Prof. - Institute of Fluid Flow Machinery Gdansk Profesional bakground 1987-1989 Gdansk University of Technology 1989 -2007 Institute of Fluid Flow Machinery Gdansk 2001-2003 Univeristy of Warmia and Mazury Olsztyn 2003...
-
Journal of Computational Multiphase Flows
Journals -
The Medieval Low Countries
Journals -
Fluid Mechanics, L/L/E, DaPE, sem. 04, summer 21/22 (PG_00050282)
e-Learning CoursesLECTURES Introduction and basic definitions. Properties of fluids. Models of fluids. Fluids in equilibrium. Determination of hydrostatic forces. Archimedes" law. Methods of fluid flow description. General motion of fluid. Deformation of fluid element. Vortex motion of fluid. Principles of conservation of mass, momentum and energy. Balance of entropy. Navier-Stokes equation. Bernoulli equation. Similarity of flow phenomena. Potential...
-
Inverse Integration of the Open Channel Flow Equations
PublicationW artykule przedstawiono metodę obliczeń umożliwiającą całkowanie równań przepływu nieustalonego w kanałach otwartych (równań de Saint Venanta) wstecz. Dyskutowano także przydatność równania retencji w zagadnieniu sterowania przepływem.
-
A study of flow boiling heat transfer in minichannels
PublicationW pracy przedstawiono badania eksperymentalne wrzenia w przepływie w minikanale o średnicy wewnętrznej 2.3mm i długości 38cm. Uzyskano rozłady temperatury wzdłuż ścianki kanału oraz lokalne współczynniki przejmowania ciepła. Dane skorelowano z korelacją półempiryczną uzyskując zadowalającą zgodność.
-
Substance flow analysis for mercury emission in Poland
Publication -
Cost approach to the flow-shop construction scheduling
Publication -
Flow and solute transport in porous media systems
PublicationPraca przedstawia podstawowe procesy fizyczne zachodzące w środowisku glebowym. Rozpoczyna się od omówienia zjawisk cieplnych i efektów temperaturowych, a następnie omawia się zjawiska dyfuzyjne i natlenienie gleby. Potem omawia się dynamikę uwilgotnienia gleb i pobierania wody przez korzenie roślinne, jak też migrację zanieczyszczeń. Pracę kończy rozdział dotyczący oczyszczania ścieków w systemie glebowo-roślinnym.
-
Flow and friction around the growing cartilage cells
PublicationInżynieria tkankowa jest jedną z najszybciej rozwijających się dziedzin biotechnologii stosowanej. Nowe metody badawcze tej nauki mogą być rozwiązane jedynie przy wzajemnej współpracy biologów, tribologów, mechaników, ortopedów klinicystów.Schorzenia chrząstki stawowej dotyczą milionów ludzi na świecie, często nawet w młodym wieku. Od kilkunastu lat z powodzeniem prowadzone są próby rekonstrukcji chrząstki stawowej oparte na dwóch...
-
Flow and pool boiling on porous coated surfaces
PublicationOmówiono wpływ powłoki porowatej na przebieg wrzenia w przepływie i w dużej objętości na przykładzie własnych badań eksperymentalnych.
-
Optimization of streamwise vortex generator for subsonic flow
PublicationW pracy przedstawiono wyniki optymalizacji generatora wirów wzdłużnych dla dwóch liczb Macha 0.3 i 0.8. Optymalizacje przeprowadzono w oparciu o algorytmy genetyczne i obliczenia przepływu trójwymiarowego wykonane programem Fluent. Wykonano badania eksperymentalne dla optymalnej konfigurację i potwierdzono większą efektywność generatora wirów.
-
Acoustic heating in a weakly dispersive fluid flow
PublicationZbadano specyficzną rolę dyspersyjnych własności płynu w generacji ogrzewania przez straty energii fali akustycznej. Przedstawiono ilustracje zaistniałego ogrzewania powstającego na skutek przejścia dwoch typów fal - impulsowej i stacjonarnej.
-
The vortex flow caused by sound in a bubbly liquid
PublicationGeneration of vorticity in the field of intense sound in a bubbly liquid in the free half-space is considered. The reasons for generation of vorticity are nonlinearity, diffraction, and dispersion. Acoustic streaming differs from that in a Newtonian fluid. Under some conditions, the vortex flow changes its direction. Conclusions concern streaming induced by a harmonic or an impulse Gaussian beam.
-
Wave damping and smoothing in the unsteady pipe flow
Publicationlaboratoryjne eksperymenty wykonane dla rur polietylenowych o różnej długości wykazały obecność takich zjawisk jak zmienna prędkość propagującej fali ciśnienia oraz jej intensywne tłumienie i wygładzanie. w artykule zaproponowano modyfikacje standardowych równań przepływu nieustalonego. polega ona na wprowadzeniu zmiennej prędkości fali oraz dyssypacji energii na jej czole opisanej członem dyfuzyjnym. do rozwiązania równań zaproponowano...
-
Numerical Simulations for Transonic Flow in Control Valve
PublicationResults of numerical simulations for transonic flow in control valve are presented. The valve is the main part of an adaptive pneumatic shock absorber. Flow structure in the valve domain and the influence of the flow non-uniformity in the valve on a mass flow rate is investigated. Numerical simulation results are compared with experimental data.
-
The logistics streamlining of the material flow at the production company
PublicationThe main practical problem in the Logistics Department at the company is overstaffing in the unit responsible for the flow of materials. Carried out by the authors of the article, some detailed research on the process analysis in the discussed company indicates that the main cause of such a situation is related to an increase in the amount of transported material and a lack of redesigning the material flow in...
-
Influence of the air phase on water flow in dikes
PublicationNumerical models are often used to describe flow and deformation processes occurring in dikes during flood events. Modeling of such phenomena is a challenging task, due to the complexity of the system, consisting of three material phases: soil skeleton, pore water and pore air. Additional difficulties are transient loading caused by variable in time water levels, heterogeneity of the soil or air...
-
Design and investigations of a micro-turbine flow part
Publication-generative micro-power plant with the HFE7100 as a working medium was designed and built for experimental investigations. The heat output of the plant was assumed equal to 20 kW, while the electric output amounted to about 3kW.In the paper a multi-stage micro-turbine with partial admission of all the stages is described in detail and the results of the particular experimental investigations and numerical calculations are shown,...
-
Experimental and theoretical analysis of dryout in annular flow
PublicationW pracy opisano badania eksperymentalne kryzysu wrzenia typu dryout, przeprowadzone w pionowych rurkach o średnicy wewnętrznej 1.15 i 2.3 mm z wykorzystaniem dwóch czynników roboczych, tj. SES36 i R123. W oparciu o wyniki tych badań zaproponowano ogólną korelację na krytyczny strumień ciepła w minikanałach.
-
Flow and pool boiling on porous coated surfaces
PublicationPrzedstawiono wyniki badań eksperymentalnych wrzenia na:a)rurkach i płytkach z powłokami porowatymi o różnej grubości i porowatości, b) rurkach, których jedynie górna część była pokryta powłoką porowatą, c) pęku rur wykonanym z rurek z powłoką porowatą. Zaprezentowano również wyniki pomiarów współczynnika przejmowania ciepła i spadku ciśnienia podczas wrzenia w w przepływie wybranych czynników chłodniczych i ich mieszanin z olejem...
-
Model of pressure distribution in vortex flow controls
PublicationThe paper is devoted to the vortex valve. Existing devices are described by CFD-methods, or by means of simple empirical relations. A rational method of the considered object design is proposed, on the base of the input and dissipation energy balance., what gives a simple algebraic equation. Conformity between calcul;ated and measured parameters of the vortex valve allows for acceptation of the proposed concept.
-
Verification of baffle factor for straight pipe flow
PublicationDuring the water disinfection devices designing, it is often assumed that the baffle factor for a straight pipe reactors is equal to one. It would be possible only for the plug flow, which is a simplified model of the flow and does not appear in real situations. The paper contains an equation which enables calculation of the real value of the baffle factor for the pipe flow.