Filters
total: 2747
displaying 1000 best results Help
Search results for: SOLAS CONVENTION
-
Experimental investigation of forced convection of water/EGAl2O3 nanofluids inside horizontal tube
PublicationIn this paper, forced convection of water/EG-Al2O3 nanofluids inside horizontal stainless steel tube is studied experimentally. As base fluid served water/EG mixture of two ratios (60:50 and 50:50). Nanoparticle mass concentrations was 0.1% or and 1%. Transition and turbulent flow regimes were tested. Average heat transfer coefficient and pressure drop values were determined for nanofluids and compared to base fluids. Deterioration...
-
Experimental investigation of forced convection of water-Al2O3 nanofluids inside horizontal tubes,
PublicationIn this paper, forced convection of water–Al2O3 nanofluids inside horizontal copper tube is studied experimentally. Experiments were conducted for three, i.e. 0.1%, 1% and 5% nanoparticle mass concentrations under transition and turbulent flow regimes. Average heat transfer coefficients and pressure drop values were determined and compared to distilled water. Enhancement of heat transfer for lower nanoparticle concentration and...
-
Experimental investigation of free convection of glycol-Al2O3 nanofluid from horizontal tube
PublicationNanofluids came to be seen as a new generation of coolants, both in single- and two phase systems. Furthermore, nanofluids or nanocomposites may be used as a media in a thermal energy storage (TES) in such systems as sensible heat storage (SHS) and phase change materials (PCM). In the SHS systems the dominating mechanism of the heat transfer is natural convection. However, in the literature only a few investigations of free convection...
-
Numerical and experimental investigation of thermal convection near electric devices with vertical channels
PublicationThis paper presents the results of numerical and experimental investigation of thermal convection near heat emitting surfaces of an electric device. For the intensification of thermal convection, special vertical channels were formed near the heat emitting surfaces of the device. An experimental test has proved that there is an optimal length of the channels – thermal convection is the most intensive then. Air velocity vectors...
-
Free convection of water-Al2O3 nanofluid from horizontal porous coated tube
PublicationNanofluids are expected to enhance heat transfer in many thermal systems. Present efforts are concentrated on boiling heat transfer of nanofluids, although single phase convection is of key importance in various appliances such as car radiators or heating systems. This paper presents experimental results of heat transfer during free convection of water-Al3O3 nanofluid from horizontal tube covered with metallic porous coating. Contrary...
-
EXPERIMENTAL INVESTIGATION OF FREE CONVECTION OF GLYCOL-Al2O3 NANOFLUID FROM HORIZONTAL TUBE
PublicationNanofluids came to be seen as a new generation of coolants, both in single- and two phase systems. Furthermore, nanofluids or nanocomposites may be used as a media in a thermal energy storage (TES) in such systems as sensible heat storage (SHS) and phase change materials (PCM). In the SHS systems the dominating mechanism of the heat transfer is natural convection. However, in the literature only a few investigations of free convection...
-
Free convection of water-Al2O3 nanofluid from horizontal porous coated tube
PublicationThe main aim of the present study was to investigate the influence of nanoparticles on heat transfer coefficients during free convection of water-Al2O3 nanofluid from horizontal porous coated tube under atmospheric pressure for nanoparticle concentration of 0.01% by weight. Contrary to published data present study concerns on free convection of nanofluids in extensive, quiescent fluid.
-
Experimental Investigations of Forced Convection of Nanofluids in Smooth, Horizontal, Round Tubes: A Review
PublicationA comprehensive review of published works dealing with experimental studies of forced convection heat transfer of nanofluids is presented. The survey is limited to straight, smooth, and round tubes. Moreover, only mono nanofluids exhibiting Newtonian behaviour are considered. Works on experimental research of forced convection in tubes are presented in a chronological order in the first part of the article. In this part, attention...
-
Featuring Semitransparent p–i–n Perovskite Solar Cells for High-Efficiency Four-Terminal/Silicon Tandem Solar Cells
PublicationTwo issues need to be resolved when fabricating p–i–n semitransparent perovskite solar cells (ST-PVSCs) for four-terminal (4 T) perovskite/silicon tandem solar cells: 1) damage to the underlying absorber (MAPbI3), electron transporting layer ([6,6]-phenyl-C61-butyric acid methyl ester, PCBM), and work function (WF) modifier (polyethylenimine, PEI), resulting from the harsh sputtering conditions for the transparent electrodes (TEs)...
-
Wind speed, wind direction and solar radiation datasets; wind and solar energy resources analysis
Open Research DataDataset contain the results of wind speed, wind direction and solar radiation for wind and solar energy resources analysis performed in years 2008 and 2009. Application for efficiency and profitability of solar and wind power plants anaylsis and for energy generation forecasting algorithms design and anaysis. Datasets used in doctoral dissertations,...
-
Synthesis and Characterization of Poly(zwitterionic) Structures for Energy Conversion and Storage
PublicationZwitterions are unique class of molecules that possess two functional groups bearing electric charges, one positive and second negative. This setup results in peculiar properties such as high water retention and anti-fouling capability. Therefore, zwitterionic coatings and gels are commonly applied in e.g. biosensing and bioelectronic devices. Despite those applications, there are other perspectives for zwitterionic materials....
-
Modified Manganese Phosphate Conversion Coating on Low-Carbon Steel
PublicationConversion coatings are one of the primary types of galvanic coatings used to protect steel structures against corrosion. They are created through chemical reactions between the metal surface and the environment of the phosphating. This paper investigates the impact that the addition of new metal cations to the phosphating reaction environment has on the quality of the final coating. So far, standard phosphate coatings have contained...
-
Clinical and conventional pharmacy services in Polish hospitals: a national survey
Publication -
The Connection Betweenagrand SCCmecElements ofStaphylococcus aureusStrains and Their Response to Photodynamic Inactivation
Publication -
Conception for diagnosing SI engines fed with biofuel in operation conditions
PublicationThe article deals with the question of diagnosing the high power self ignition (SI) engines fed with pro-ecologic fuels in an aspect of appearing operation problems. There has been presented the specific of action and techno-operation profile of the combustion engine foreseen as an investigations object. The preliminary conception of diagnostic investigations of the engine 7L35MC type produced in H. Cegielski - Poznan S.A. factory...
-
Growth and characterization of chalcopyrite nanocrystals: beyond conventional thin films
PublicationPrzedstawiona została sucha metoda wytwarzania na podłożach stałych kryształów chalkopirytu zawierających miedź z wykorzystaniem prekursorów metalicznych. Dzięki odpowiedniemu doborowi parametrów nakładania otrzymano zarówno nanokryształy oraz polikrystaliczne struktury submikronowe jak i makroskopowe klastry. Zamieszczona została charakterystyka wytworzonych materiałów otrzymana techniką mikroskopii skaningowej.
-
Performance of FAN conception of traffic control in IP QoS networks
PublicationIn this paper we present the architectural implementation of Flow Aware Networking (FAN), a new approach for realizing QoS guarantees in the Internet. We also propose FAN traffic control algorithm which performs traffic control on flow level. Using the proposed FAN node model, we conduct simulation research to prove if FAN can be a new approach for realizing QoS guarantees. The basis of this research is finding a way to guarantee...
-
Numerical assessment of maneuvering properties of ship with a conventional type of propulsion
Publication -
Application of guided waves in the evaluation of steel-concrete adhesive connection
Publication -
Polarization Conversion of Solitons Propagating in Birefringent Microstructured Optical Fibers
Publication -
Conventional and unconventional yeasts able to grow on rapeseed meal hydrolysates
Publication -
Comparative study of flow condensation in conventional and small diameter tubes
PublicationFlow boiling and flow condensation are often regarded as two opposite or symmetrical phenomena, however their description with a single correlation has yet to be suggested. In the case of flow boiling in minichannels there is mostly encountered the annular flow structure, where the bubble generation is not present. Similar picture holds for the case of inside tube condensation, where annular flow structure predominates. In such...
-
Comparative study of flow condensation in conventional and small diameter tubes
PublicationIn the paper a method developed earlier by the first author is applied to calculations of heat transfer coefficient for inside tube condensation. The method has been verified using experimental data from literature on several fluids in different microchannels and compared to three well established correlations.
-
Conception of interactive information and decision support system - model and evaluation
PublicationThis article presents conception of interactive information and decision support system for urban and industrial air quality management. The emphasis of the project is on real-time analysis and multi-media information, and support of distributed and mobile clients through the Internet.
-
Offshore project management based on jack-up rig conversion
PublicationChapter presents aspects of Offshore project management during conversion drilling rig to accommodation rig in Batam Indonesia
-
Application of guided waves in the evaluation of steel-concrete adhesive connection
PublicationThe aim of the paper is the application of guided waves in the evaluation of a condition state of adhesive connection between steel and concrete. The study concerns a push-out specimen consisting of two steel plates glued to opposite faces of a concrete cube with the use of structural adhesive. Wave propagation in the specimen without external load is investigated both experimentally and numerically. The second stage of the investigation...
-
Sample Rate Conversion Based on Frequency Response Masking Filter
PublicationThe sample rate conversion with high resampling ratios requires low-pass digital filters with very narrow transition band which results in high computational complexity and makes filter design problematic. Therefore in this work we propose to use the FRM method, which breaks the filter with a narrow transition band into a group of filters with reduced design requirements. These decreases the number of non-zero coefficients and...
-
The categorization of the tourist services quality perception determinants in hierarchical conception
PublicationW niniejszym rozdziale zaprezentowano kategoryzację determinant percepcji jakości usług turystycznych. Omówione zostały główne grupy oraz determinanty elementarne z wykorzystaniem ujęcia modeli hierarchicznych.
-
Fixed roof to shell connection in tank with an internal floating cover.
PublicationReferat dotyczy projektowania połączenia dachu stałego zbiornika walcowego z płaszczem w przypadku zastosowania wewnętrznego przekrycia pływającego. Zaproponowano zastosowanie dodatkowego pierścienia usztywniającego, zabezpieczającego górną krawędź płaszcza zbiornika. Wyniki analiz z zastosowaniem metody elementów skończonych zamieszczono w formie map naprężeń.
-
On Sample Rate Conversion Based on Variable Fractional Delay Filters
PublicationThe sample rate conversion algorithm based on variable fractional delay filters is often used if the resampling ratio cannot be expressed as the ratio of small integer numbers or if it is not constant. The main advantage of such solution is that it allows for arbitrary resampling ratios which can even be changed during the resampling process. In this paper a discussion on influence of different approaches to fractional filter...
-
ASON/GMPLS connection control servers in virtual computer environment
PublicationIn the paper ASON/GMPLS connection control servers layer in the context of Next Generation Network (NGN) is described. The implementation of ASON/GMPLS connection control servers in virtual computer environment as well as performed measurements are presented. Some aspects of virtual environment installation are depicted. Remarks regarding application of the virtual computer environment to realization of communication between NGN...
-
Comparative study of flow condensation in conventional and small diameter tubes
PublicationFlow boiling and flow condensation are often regarded as two opposite or symetrical phenomena. Their description however with a single correlation has yet to be suggested.In the case of flow boiling in minichannels there is mostly encountered the annular flow structure, where the buble generetion is not present. Similar picture holds for the case of inside tube condensation, where annular flow structure predominates. In such case...
-
A Point Set Connection Problem for Autonomous Mobile Robots in a Grid
PublicationConsider an orthogonal grid of streets and avenues in a Manhattan-like city populated by stationary sensor modules at some intersections and mobile robots that can serve as relays of information that the modules exchange, where both module-module and module-robot communication is limited to a straight line of sight within the grid. The robots are oblivious and move asynchronously. We present a distributed algorithm that, given...
-
A closed loop thermosyphon with conventional or minichannel based condenser and evaporator
PublicationPrzedstawiono uogólniony model termosyfonu, który może być rozpatrywany dla szeregu wariantów.Model opiera się na jednowymiarowych równanich masy, pędu i energii. Rozpatrzono dwa przypadki termosyfonu, tj. grzanie strony pionowej i chłodzenie strony pionowej oraz drugi, gdzie termosyfon jest ogrzewany na stronie pionowej a chłodzony na poziomej.
-
Conception of taking decisions with regard to reliability and safety of combustion engines
PublicationW referacie przedstawiono jedną z najprostszych sytuacji decyzyjnych, która może pojawić sie w czasie eksploatacji silników spalinowych. Zaproponowano możliwość podejmowania decyzji w takiej sytuacji. Wynika z niej, że nawet w złożonej sytuacji decyzyjnej rozpatrywanie oczekiwanych konsekwencji umożliwia bardzo łatwe przyporządkowanie każdemu rodzajowi decyzji, pojedynczej liczby oznaczającej wartość oczekiwaną konsekwencji. Umożliwia...
-
On bounded load routings for modeling k-regular connection topologies
PublicationW pracy analizowane są problemy modelowania k-regularnych topologii sieci komputerowych z punktu widzenia routingu typu point-to-point. Zaprezentowane są algorytmy oraz przeprowadzona jest analiza złożoności obliczeniowej.
-
Intensification of thermal convection near electric devices using flat screens – computer modelling
PublicationIntensification of natural thermal convection near electric devices is possible by application of additional elements as screens creating convection canals close to the device. In the earlier authors paper the results of the analysis of thermal convection with the use of only one additional screen close to the electric device were presented. This paper presents computer modelling of thermal convection when two screens near the...
-
CFD analysis of natural convection between two superposed fluids: role of corrugated bottoms
Publication -
Impact of the trap–assisted recombination in the perovskite solar cells
PublicationTo achieve the highest performance using perovskite solar cells it is necessary to understand all the dominant mechanisms which affect the operation of solar cell. Here, we have investigated the bulk and interface trap–assisted recombination processes in the solar cells with p–i–n architecture. These studies are based on the numerical and experimental methods to get better understanding of these physical processes. The following results...
-
Stabalization of solar-panel energy system for Pakistani household
PublicationRenewable energy resources such as Sun and wind are getting popular and easier to use day by day. It is a better method to fulfill our demands as sun is a continuous source of energy for Earth. Many countries are fulfilling their demands by Solar Panels. Solar panel is used as a converter between sunlight and electrical energy. This research paper is going to tell that how to obtain electrical energy from sunlight more efficiently...
-
Polymers in High-Efficiency Solar Cells: The Latest Reports
Publication -
Photovoltaic solar energy development in the Baltic Sea Region
PublicationInformacje zawarte w tym artykule odzwierciedlają różnorodność rozwoju technologii fotowoltaicznych i różnorodność etapów realizacji PV przez kraje regionu Morza Bałtyckiego (Dania, Finlandia, Niemcy, Łotwa, Litwa, Szwecja, Polska, Estonia).
-
The effect of temperature difference on heat transport in solar cells
PublicationW pracy omówiono wpływ wzrostu temperatury i mechanizm transportu ciepła na drodze przewodzenia w układach hybrydowych PV/T. Wyznaczono współczynniki przewodzenia krystalicznego krzemu typu n i p oraz gęstość strumienia ciepła w zakresie temperatur od 0 do 100 st. C.
-
Fermentative Conversion of Two-Step Pre-Treated Lignocellulosic Biomass to Hydrogen
PublicationFermentative hydrogen production via dark fermentation with the application of lignocellulosic biomass requires a multistep pre-treatment procedure, due to the complexed structure of the raw material. Hence, the comparison of the hydrogen productivity potential of different lignocellulosic materials (LCMs) in relation to the lignocellulosic biomass composition is often considered as an interesting field of research. In this study,...
-
EXPERIMENTAL ANALYSIS OF CONNECTION BETWEEN OBJECT-ORIENTED METRICS AND SOFTWARE CHANGEABILITY
PublicationFor the purpose of video surveillance software quality assessment in this work the ISO/IEC-9126 norm was used with a particular focus on maintainability of the software system. The paper presents a study on the connection between software metrics derived from the static analysis of the source code and changeability of the video surveillance software system. It is shown that meeting requirements of software quality metrics may result...
-
A Wind Energy Conversion System Based on a Generator with Modulated Magnetic Flux
PublicationIn this work, the concept of an energy conversion system for wind turbines based on the modified permanent magnet synchronous generator (PMSG) is presented. In the generator, a pair of three-phase windings is used, one of which is connected in a “star” and the second in a “delta” configuration. At the outputs of both windings, two six-pulse uncontrolled (diode) rectifiers are included. These rectifiers are mutually coupled by a...
-
Possibility of use adsorption chillers for increase efficiency in conventional power plant
Publication -
Energy conversion in small water plants with variable speed PM generator
Publication -
Connection of microcosm with macrocosm in Max Scheler's philosophy: man, logos and ethos
PublicationW eseju pokazałem znaczenie mikrokosmicznego wymiaru w ludzkim personalnym życiu. To jest w świecie Zachodu kompleksowa próba, aby uchwycić związek "mikrokosmosu" z "makrokosmosem w filozoficznym dziele Maxa Schelera. Następnie uwypukliłem, że z racji jego powiązania jako pojęcia "mikrokosmosu" z kwestią kształcenia, wtedy w indywidualnej ludzkiej osobie pojęcie to osiąga "prawo obywatelstwa" w Schelerowskiej...
-
Stress analysis in the steel tank shell at its connection with product pipeline
PublicationPrzeanalizowano zaburzenia stanu błonowego w powłoce zbiornika walcowego pionowego w strefie przyłączenia do płaszcza rurociągu produktowego