Filtry
wszystkich: 1292
wybranych: 1063
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: FIN-TUBE HEAT EXCHANGER, HEAT TRANSFER
-
Liquid crystal technique application for heat transfer investigation in afin-tube heat exchanger element
PublikacjaPublikacja przedstawia rezultaty prac autorów w zakresie wykorzystania termografii ciekłokrystalicznej w badaniach wymiany ciepła dla różnych elementów wymienników ciepła. Technika ta z powodzeniem została zastosowana do analizy zabudowy wymiennika na jego efektywność.
-
Liquid crystal technique application for heat transfer investigation inafin-tube heat exchanger element
PublikacjaPublikacja przedstawia rezultaty prac autorów w zakresie wykorzystania techniki ciekłokrystalicznej w badaniach wymiany ciepła dla elementów wymiennika ciepła. Technika ta z powodzeniem została zastosowana do analizy sposobu zabudowy wymiennika na jego efektywność.
-
Thermodynamic and geometrical characteristics of mixed convection heat transfer in the shell and coil tube heat exchanger with baffles
PublikacjaThe article presents passive heat transfer enhancement method in the form of baffles to increase the energy efficiency of the shell coil heat exchanger. Conducted literature review shows that, despite numer- ous studies, there is little work on the intensification of heat transfer at the shell side. Most of the work focuses on the impact of geometrical parameters of the coil itself. This article successfully proves that it is possible...
-
Boiling heat transfer performance of the thermosiphon heat exchanger
PublikacjaPrzedstawiono wyniki badań eksperymentalnych prototypowego, termosyfonowgo wymiennika ciepła. W szczególności określono wpływ geometrii pęku rur, stanu powierzchni rurek oraz poziomu cieczy w parowniku na wydajność cieplną wymiennika.
-
HEAT TRANSFER CHARACTERISTICS OF ENHANCED SHELL AND COIL HEAT EXCHANGER
PublikacjaIn the paper authors presented their own constructions of shell and tube heat exchangers with intensified heat transfer. The shell and coils heat exchangers are in common use in heat ventilations and air conditioning systems. Those types of recuperators are quite simple constructions, the low value of pressure drops and good conditions of heat transfer. The present study shows an experimental investigation of the heat transfer...
-
Heat transfer characteristics of a two-phase thermosyphon heat exchanger
PublikacjaPrzedstawiono wyniki badań wpływu geometrii parownika, rodzaju rur użytych do budowy parownika, rodzaju cieczy pośredniej oraz poziomu cieczy nad najwyższym rzędem rur na działanie dwufazowego, termosyfonowego wymiennika ciepła. Zaprezentowano algorytm obliczeń przedstawionego wymiennika.
-
High Performance Tubular Heat Exchanger with Minijet Heat Transfer Enhancement
PublikacjaIn the paper, the original cylindrical heat exchanger with minijets (MJHE) was introduced. The systematic experimental analysis of the prototype heat exchanger was described with special attention paid to such parameters as the heat transfer effectiveness, heat transfer rates, overall heat transfer coefficients, and pressure drop. The heat transfer coefficients were determined based on Wilson plot method, the most suitable approach...
-
Heat transfer intensification by enlarged surface roughness in the plate heat exchanger
PublikacjaIn the paper an experimental analysis of passive heat transfer intensification technique employed in the case of the plate heat exchanger is presented. The passive intensification was obtained by a modification of the heat transfer surface. The roughness of surface was increased by a use of glass micro-beads. Single-phase convective heat transfer in the water-water system was studied. The experiment was accomplished in two stages....
-
Thermal-Hydraulic Studies on the Shell-and-Tube Heat Exchanger with Minijets
PublikacjaIn this paper a patented design of a heat exchanger with minijets, with a cylindrical construction is presented. It is followed by the results of its systematic experimental investigations in the single-phase convection heat transfer mode. Based on these results, validation of selected correlations (coming from the literature) describing the Nusselt number was carried out. An assessment of the heat exchange intensification level...
-
The influence of microjet array area ratio on heat transfer in the compact heat exchanger
PublikacjaThe paper describes the comprehensive study on the effect of microjet array geometrical parameters on the heat transfer enhancement in the modular heat exchanger. The conducted experimental study provides an experimental database on single phase submerged microjet heat transfer. The Wilson plot method was applied to determine the heat transfer coefficients in the laminar and transition flow regimes of a liquid-to-liquid heat exchanger....
-
Heat transfer and pressure drop characteristics of the silicone-based plate heat exchanger
PublikacjaThe paper presents an experimental investigation of a silicone based heat exchanger, with passive heat transfer intensification by means of surface enhancement. The main objective of this paper was to experimentally investigate the performance of a heat exchanger module with the enhanced surface. Heat transfer in the test section has been examined and described with precise measurements of thermal and flow conditions. Reported...
-
Heat transfer in plate heat exchanger channels: experimental validation of selected correlation equations
PublikacjaThis study is focused on experimental investigation of selected type of brazed plate heat exchanger. The Wilson approach was applied in order to estimate heat transfer coefficients for the PHEx passages. The main aim of the paper was to experimentally check ability of several correlations published in the literature to predict heat transfer coefficients by comparison experimentally obtained data with appropriate predictions. The...
-
Heat transfer in plate heat exchanger channels: experimental validation of selected correlation equations
PublikacjaThis study is focused on experimental investigation of selected type of brazed plate heat exchanger. The Wilson approach was applied in order to estimate heat transfer coefficients for the PHEx passages. The main aim of the paper was to experimentally check ability of several correlations published in the literature to predict heat transfer coefficients by comparison experimentally obtained data with appropriate predictions. The...
-
Experimental investigations on heat transfer enhancement in shell coil heat exchanger with VARIABLE Baffles GEOMETRY
PublikacjaThe paper presents the possibility of using passive intensification of heat transfer in the form of baffles to increase the energy efficiency of the shell and coil heat exchanger. The experiment was carried out by using a modular coil heat exchanger in the form of an electric heater. Water was used as a working fluid with constant thermal-flow parameters at the inlet of the module. It should be noted that experiments were made...
-
Heat transfer during pool boiling on smooth tube bundle
PublikacjaPrzedstawiono wyniki pomiarów współczynnika przejmowania ciepła dla pęku 19 gładkich rurek ze stali nierdzewnej ogrzewanych elektrycznie podczas wrzenia wody destylowanej, metanolu i R141b. Zaproponowano równanie korelacyjne do obliczania średniego współczynnika przejmowania ciepła.
-
Influence of metallic porous microlayer on pressure drop and heat transfer of stainless steel plate heat exchanger
PublikacjaThe experimental analysis of passive heat transfer intensification in the case of plate heat exchanger has been carried out. On the heat transfer surface of heat exchanger the metallic porous layer was created. The experiment was accomplished in two stages. In the first stage the commercial stainless steel gasketed plate heat exchanger was investigated, while in the second one – the identical heat exchanger but with the modified...
-
Influence of metallic porous microlayer on pressure drop and heat transfer of stainless steel plate heat exchanger
PublikacjaThe experimental analysis of passive heat transfer intensification in the case of plate heat exchanger has been carried out. The metallic porous layer was created on the heat transfer surface of analyzed unit. The experiment was accomplished in two stages. In the first stage the commercial stainless steel gasketed plate heat exchanger was investigated, while in the second one – the identical heat exchanger but with the modified...
-
Experimental study on single phase operation of microjet augmented heat exchanger with enhanced heat transfer surface
PublikacjaThe article presents experimental investigations on a prototype heat exchanger. Presented research is focused on combined active and passive enhancement techniques of surface modification and microjet impingement. The results were compared to reference plate heat exchanger without microjet impingement. The Wilson plot method was applied to determine the heat transfer coefficients in the single phase operation. The heat exchanger...
-
Experimental and numerical simulations of flow and heat transfer in heat exchanger elements using liquid crystal thermography.
PublikacjaW artykule przedstawiono założenia oraz sposób prowadzenia eksperymentu i obliczeń numerycznych wymiany ciepła w modelu wymiennika ciepła przy użyciu termografii ciekłokrystalicznej.
-
A new construction of shell-and-tube heat exchanger with impinging jets and minichannels technologies for heat recovery from gases – experimental analysis
PublikacjaA dynamic development of technologies allowing waste heat utilization is observed in a correspondence with a pro-ecological approach of the zero waste idea. Such approach becomes the most demanding in the area of low-temperature was heat sources, especially gaseous media. Till now, they were usually not utilized due to unfavorable thermal conditions and high costs. Therefore, the zero waste approach directs research on techniques...
-
Experimental investigation of heat transfer enhancement in straight and U-bend double-pipe heat exchanger with wire insert
PublikacjaIn this paper, the possibility of heat transfer enhancement in the U-bend exchanger was presented. Experimental research has been carried out for four individual heat exchanger constructions i.e. plain tube in tube, turbulized tube in tube, plain U-bend and U-bend with turbulator. Also, heat transfer experiments for various boundary conditions were performed to obtain reference values. In case of U-bend exchanger with and without...
-
Influence of pressure on heat transfer during pool boiling on smooth tube bundle
PublikacjaPrzedstawiono wyniki badań eksperymentalnych wrzenia wody, metanolu i R141b na pęu rur głądkich w warunkach podcisnienia i ciśnienia atmosferycznego
-
An experimental investigation on the effect of new continuous core-baffle geometry on the mixed convection heat transfer in shell and coil heat exchanger
PublikacjaIn the article, the authors presented the influence of continuous core-baffle geometry at mixed convection heat transfer in shell and coil heat exchanger. Experiments were carried out for a large power range, i.e. from 100W to 1200W and mass flow rates ranging from 0.01 kg/s to 0.025 kg/s. During the experiments, the mass flow rate of cooling water, the temperature of water at the inlet and outlet as well as the wall temperature...
-
Thermal and economic investigation of straight and U-bend double tube heat exchanger with coiled wire turbulator
PublikacjaExperimental research has been carried out for four individual heat exchanger constructions, i.e., plain double tube, turbulized double tube, plain U-bend and U-bend with turbulator. Tests were made for the water-water system. The study covered a wide measuring range, i.e., Re = 800–9000 – on the shell side, for a constant cold water temperature of 9 ◦C and hot water of 50 ◦C. The heat exchangers were made from copper tubes with...
-
Experimental investigation on straight and u-bend double tube heat exchanger with active and passive enhancement methods
PublikacjaAuthors in this work want to demonstrate the possibility to increase the heat transfer efficiency by using simple wire coil inserts to create turbulent flow in the boundary layer as well as air blowing into the annulus of the pipe. In the study, Wilson plot approach was applied in order to estimate heat transfer coefficients for all heat exchanger (HX) configurations. The study focuses on experimental values of heat transfer coefficient...
-
Nucleate pool boiling heat transfer from small horizontal smooth tube bundles
PublikacjaPrzedstawiono wyniki pomiarów współczynnika przejmowania ciepła podczas wrzenia wody destylowanej, metanolu i R141b na poziomym pęku rur gładkich, który składał się z 19 rurek, ogrzewanych elektrycznie, w układzie przestawionym i podziałce 1.7d oraz 2.0d. Wyznaczono również wartości współczynnika wpływu pęku. Podano równanie korelacyjne do obliczania średniego współczynnika przejmowania ciepła
-
Influence of wall temperature on heat transfer coefficient during R 22 boiling in microfin tube
PublikacjaPrzedstawiono wyniki badań współczynnika przejmowania ciepła i spadku ciśnienia podczas wrzenia czynnika R 22 w rurze nisko żebrowanej. Opisano stanowisko i procedurę badawczą. Zaobserwowano spadek współczynnika przejmowania. Opisano stanowisko i procedurę badawczą. Zaobserwowano spadek współczynnika przejmowania ciepła wraz ze wzrostem temperatury ścianki rury.
-
Heat Transfer During Pool Boiling of Water, Methanol and R141b on Porous Coated Horizontal Tube Bundles
PublikacjaThis paper presents the results of experimental investigation of water, methanol and R141b refrigerant boiling on horizontal porous coated tube bundles supposed to represent a flooded-type evaporator. Experiments were carried out for a bundle of 19 tubes in triangular layout for two pitch-to-diameter ratio values – 1.7 and 2.0 – in atmospheric and sub-atmospheric pressure conditions. Average heat transfer coefficients – both local,...
-
Heat transfer and pressure drop during flow boiling of refrigerant/oil mixture inside smooth tube
PublikacjaW pracy przedstawiono wyniki badań współczynnika przejmowania ciepła i spadku ciśnienia podczas wrzenia czystych oraz zaolejonych czynników chłodniczych (R22, R134a, R407C) wrzących w poziomej stalowej rurce.
-
Heat transfer during pool boiling of water, methanol and R141b on porous coated horizontal tube bundles
PublikacjaPrzedstawiono wyniki badań eksperymentalnych wrzenia wody, metanolu i R141b na poziomym pęczku rur pokrytych metaliczna powłoką porowatą. Badania przeprowadzono dla podziałek rur 1.7d oaz 2d, przy ciśnieniu atmosferycznym i podciśnieniu.
-
Heat transfer and pressure drop during flow boiling of pure efrigerants and refrigerant/oil mixtures in tube with porous coating
PublikacjaW pracy przedstawiono wpływ powłoki porowatej na średni współczynnik przejmowania ciepła oraz opory przepływu podczas wrzenia wybranych czynników chłodniczych wewnątrz poziomych rurek. Badania przeprowadzono dla techniczne czystych czynników chłodniczychR22, R134a i R407C oraz ich mieszanin z olejem poliestrowym 1% i 5% wrzących w rurkach wykonanych ze stali nierdzewnej, o wewnętrznej powierzchni gładkiej oraz z metaliczną powłoką...
-
The effect of pressure on heat transfer during pool boiling of water-Al2O3 and water-Cu nanofluids on stainless steel smooth tube
PublikacjaPrzedstawiono wyniki badań eksperymentalnych wrzenia nanocieczy woda-Al2O3 i woda-Cu o koncentracjach nanocząstek 0.01%, 0.1% oraz 1% przy ciśnieniu absolutnym 10 kPa, 100 kPa oraz 200k Pa.
-
Analysis of transient heat transfer operation in tube wall.Selected papers from the International Conference on Turbines of Large Output devoted to 100th Anniversary of Prof. Robert Szewalski Birthday.
PublikacjaW pracy przedstawiono zachowanie się wymiennika ciepła stosowanego w układzie regeneracji turbin parowych w niestacjonarnych warunkach pracy.
-
An advanced thermal-FSI approach of an evaporation of air heat pump
PublikacjaThe paper presents selected problems of numerical modeling of an advanced thermal-FSI approach of evaporator of air heat pomp. The example of a fin-tube evaporator has been studied, focusing on obtaining of heat exchanger characteristics applying two-phase flow model for the in-tube refrigerant flow. Special attention is given to heat transfer between separated medium for different air velocity and changed refrigerant mass flow...
-
A simple approach to heat exchanger sizing optimisation by means of entrophy generation minimisation
PublikacjaIn the paper an attempt is presented to find the method of optimization of microtube diameter with respect to optimal thermal-hydraulic conditions in the single-phase shell-and-tube heat exchangers. The approach is based on consideration of pumping power at the condition of maximum heat transfer by the heat exchanger tube system. In the optimization method the tube diameter is first specified and then appropriate calculations are...
-
Experimental and Computational Fluid Dynamics Studies on Straight and U-Bend Double Tube Heat Exchangers with Active and Passive Enhancement Methods
PublikacjaIn this work, the authors wanted to demonstrate the possibility to increase the heat transfer efficiency by using simple wire coil inserts to create turbulent flow in the boundary layer as well as air blowing into the annulus of the pipe. Experimental investigations were carried out for four heat exchanger constructions, i.e., plain double tube, turbulized double tube, plain U-bend double tube, U-tube with turbulator, plain double...
-
Performance analyses of helical coil heat exchangers. The effect of external coil surface modification on heat exchanger effectiveness
PublikacjaThe shell and coil heat exchangers are commonly used in heating, ventilation, nuclear industry, process plant, heat recovery and air conditioning systems. This type of recuperators benefits from simple construction, the low value of pressure drops and high heat transfer. In helical coil,centrifugal force is acting on the moving fluid due to the curvature of thetube results in the development. It has been long recognized that the...
-
EFFECT OF NANOFLUID CONCENTRATION ON TWO-PHASE THERMOSYPHON HEAT EXCHANGER PERFORMANCE
PublikacjaAn approach – relaying on application of nanofluid as a working fluid, to improve performance of the two-phase thermosyphon heat exchanger (TPTHEx) has been proposed. The prototype heat exchanger consists of two horizontal cylindrical vessels connected by two risers and a downcomer. Tube bundles placed in the lower and upper cylinders work as an evaporator and a condenser, respectively. Distilled water and nanofluid water-Al2O3...
-
Parametric study of fluid flow and heat transfer over louvered fins of air heat pump evaporator
PublikacjaTwo-dimensional numerical investigations of the fluid flow and heat transfer have been carried out for the laminar flow of the louvered fin-plate heat exchanger, designed to work as an air-source heat pump evap- orator. The transferred heat and the pressure drop predicted by simulation have been compared with the corresponding experimental data taken from the literature. Two dimensional analyses of the louvered fins with varying...
-
Experimental investigation of two-phase thermosyphon heat exchanger charged with acetone
PublikacjaThis paper presents thermal characteristics of prototype of a two-phase thermosyphon heat exchanger (TPTHEx) charged with acetone as a working fluid. The TPTHEx consists of two horizontal cylindrical vessels connected by two risers and a downcomer. Tube bundles placed in the lower and upper cylinders work as an evaporator and a condenser, respectively. The tested TPTHEx operates in a vacuum. Therefore, the working liquid is boiled...
-
Performance of the domestic micro ORC equipped with the shell-and-tube condenser with minichannels
PublikacjaIn this paper, the original compact shell-and-tube heat exchanger with circular minichannels of in-house design and manufacturing is presented as the condenser for the domestic micro heat and power plant investigations as well as other future technical applications. The heat exchanger is equipped with turbulizing baffles inside the shell. The shell itself is made of a tubular sleeve having an inner diameter of 0.067 m and the length...
-
CHARAKTERYSTYKA WYMIANY CIEPŁA I OPORÓW PRZEPŁYWU OMYWANIA MIKROSTRUGAMI ROZWINIĘTEJ POWIERZCHNI
PublikacjaW artykule przedstawiono eksperymentalne badania kompaktowego wymiennika ciepła z intensyfikacją przejmowania ciepła przy użyciu mikrostrug. Niniejszy artykuł przedstawia projekt i testy prototypu, wymiennika ciepła typu mikrostrugowego. Modułowa konstrukcja wymiennika umożliwia zmianę wymiarów geometrycznych, a także zmianę materiału przegrody wymiennika ciepła. Metoda graficzna Wilsona została z zastosowana w celu określenia...
-
Numeryczna analiza możliwości zwiększenia efektywności grzewczej pompy ciepła, poprzez modyfikację skraplacza
PublikacjaW niniejszej pracy określono charakterystykę prostego modelu wymiennika ciepła bazującego na skraplaczu powietrznej pompy ciepła. Jest to helikoidalny rekuperator typu rura w rurze. Zaproponowano i poddano analizie numerycznej dwie metody intensyfikacji wymiany ciepła i zestawiono wyniki z modelem porównawczym. Zastosowane rozwiązania zwiększające strumień wymienianego ciepła spowodowały wzrost odbieranego przez wodę strumienia...
-
Design and experimental investigations of a cylindrical microjet heat exchanger for waste heat recovery systems
PublikacjaCompact heat exchangers have more and more applications in many areas, including the HVAC, food and petrochemical industry. This paper describes the development of heat exchanger technology for waste heat recovery (WHR) from a range of processes. Case-study testing shows that the proposed heat exchanger can successfully enhance heat transfer and recover waste heat in a range of applications making them economically, environmentally and...
-
Applicability of arrays of microjets heat transfer correlations to design compact heat exchangers
PublikacjaThe article presents experimental studies on a compact heat exchanger with heat transfer intensification by means of impinging microjets. The pursuit to provide high performance of heat exchangers is a response to the demand both in economics and in the universal tendency to miniaturization of industrial equipment. This paper presents the design and tests of a prototype, microjet heat exchanger. The modular design of the heat exchanger...
-
Natural convective heat transfer from isothermalconic
PublikacjaTheoretical considerations on convective heat transfer from isothermal upward conicalsurfaces have been presented. The physical model of this phenomenon consists of an isothermalcone of inclination angle (φ) between the cone generating line (X) and the radius (R) of the cone base. The angle is a parameter of conical surface which varied from (φ = 0−circular horizontal plate) to (φ = π/2—vertical cylinder) . Onthe basis of Navier–Stokes...
-
Effect of surface roughness on thermal-hydraulic characteristics of plate heat exchanger
PublikacjaIn the paper the experimental analysis of passive heat transfer intensification in the case of modeled plate heat exchanger is conducted. The plate heat exchanger is chosen for the analysis because this kind of heat exchangers could be prospectively applied in the ORC systems, however other areas or application are equally possible. The experimental setup was assembled at the Department of Energy and Industrial Apparatus of Gdansk...
-
Plate heat exchanger with porous structure for potential use in ORC system
PublikacjaThe experimental analysis of passive heat transfer intensification in the case of plate heat exchanger has been carried out. The passive intensification was obtained by a modification of the heat transfer surface, which was covered by a metallic porous microlayer. The experiment was accomplished in two stages. In the first stage the commercial stainless steel gasketed plate heat exchanger was investigated, while in the second one...
-
Plate heat exchanger with porous structure for potential use in ORC system
PublikacjaThe experimental analysis of passive heat transfer intensification in the case of plate heat exchanger has been carried out. The passive intensification was obtained by a modification of the heat transfer surface, which was covered by a metallic porous microlayer. The experiment was accomplished in two stages. In the first stage the commercial stainless steel gasketed plate heat exchanger was investigated, while in the second one...
-
Thermal-FSI modeling of flow and heat transfer in a heat exchangerbased on minichanels
PublikacjaIn this paper selected numerical modelling problems for an advanced thermal-FSI ("Fluid Solid Interaction") mini-channel heat exchanger model are presented. Special attention is given to the heat transfer between the separated mediums for different mass flows. Similar modelling problems have also been discussed in the literature dedicated to numerical and theoretical modelling problems for typical heat exchangers [1, 2, 3]. Basic...
-
Experimental study and comparison with predictive methods for flow boiling heat transfer coefficient of HFE7000
PublikacjaThis article describes an experimental study of flow boiling of HFE7000 inside a smooth vertical channel. The investigation has been carried out in a circular stainless-steel tube with an inner diameter of 2.3 mm. The data have been collected for the applied heat fluxes q ranging from 61 to 205 kW/m2, the mass flux G ranging from 214 to 1006 kg/(m2 s), the saturation temperature Tsat ranging from 30 to 54 °C and the full range...
-
Numerical Study of Turbulent Flow and Heat Transfer of Nanofluids in Pipes
PublikacjaIn this work, Nusselt number and friction factor are calculated numerically for turbulent pipe flow (Reynolds number between 6000 and 12000) with constant heat flux boundary condition using nanofluids. The nanofluid is modelled with the single-phase approach and the simulation results are compared with experimental data. Ethylene glycol and water, 60:40 EG/W mass ratio, as base fluid and SiO2 nanoparticles are used as nanofluid...
-
Thermal performance of a prototype plate heat exchanger with minichannels under boiling conditions
PublikacjaTo solve the problem and to meet the requirements of customers in the field of high heat fluxes transfer in compact units, a new design of plate heat exchanger with minichannels (minichannels PHE) was proposed. The aim was to construct a compact heat exchanger of high effectiveness for the purpose of household cogeneration ORC system. In this paper the experimental analysis of an assembled prototype of such compact heat exchanger...
-
A simplified energy dissipation based model of heat transfer for subcooled flow boiling
PublikacjaIn the paper a model is presented based on energetic considerations for subcooled flow boiling heat transfer. The model is the extension of authors own model developed earlier for saturated flow boiling and condensation. In the former version of the model we used the heat transfer coefficient for the liquid single-phase as a reference level, due to the lack of the appropriate model for heat transfer coefficient for the subcooled...
-
Flow distribution and heat transfer in minigap and minichannel heat exchangers during flow boiling
PublikacjaThe topic of boiling heat transfer in miniscale geometries has focused the ever increasing interest of researchers in recent years. However, most of the works are related to mini- and microchannels and much less to minigaps. Meanwhile, minigaps allow for more comprehensive experimental studies, i.e. flow visualisations due to the flat, two-dimensional configuration of the flow. The results of the experimental investigations of...
-
Natural convective heat transfer from isothermal cuboids
PublikacjaThe paper presents results of theoretical and experimental investigations of the convective heat transfer from isothermal cuboid. The analytical solution was performed taking into account complete boundary layer length and the manner of its propagation around isothermal cuboid. It arises at horizontal bottom surface and grows on vertical lateral surface of the block. After changing its direction, the boundary layer occurs above...
-
A simplified energy dissipation based model of heat transfer for post-dryout flow boiling
Publikacjamodel for post dryout mist flow heat transfer is presented based on considerations of energy dissipation in the flow. The model is an extension of authors own model developed earlier for saturated and subcooled flow boiling. In the former version of the model the heat transfer coefficient for the liquid singlephase convection as a reference was used, due to the lack of the appropriate model for heat transfer coefficient for the...
-
Numerical analysis of high temperature minichannels heat exchanger performance
PublikacjaNowadays, the most difficult technological challenge in energy sector is connected with the gas micro-CHP units, dedicated to the distributed power generation. They are expected to be of high efficiency and at the same time of compact in size. Regarding the first reason, significant increase in microturbine efficiency can only be achieved by increase in the engine operating temperature. Therefore, one of the critical elements in...
-
Experimental study of flow boiling pressure drop and heat transfer of R1233zd(E) at moderate and high saturation temperatures
PublikacjaThe paper presents the results of experimental study of flow boiling of R1233zd(E) in minichannel at moderate and high saturation temperatures. The heat transfer coefficient and pressure drop were measured for flow boiling in a stainless steel tube with 2 mm inside diameter and a length of 300 mm. Experiment has been conducted for saturation temperatures ranging from 83 to 145 °C which corresponds to values of reduced pressures...
-
Performance of a plate heat exchanger operated with water-Al2O3 nanofluid
PublikacjaThis study is focused on experimental investigation of a selected type of brazed plate heat exchanger (PHEx). The main aim of the paper was to experimentally check the ability of nanofluids to enhance the performance of PHEx. A typical water-Al2O3 nanofluid was tested and compared to that of the base fluid, i.e. water. Nanoparticles were tested at the concentration of 0.1% and 1% by weight. Impact of the 1 day and 3 days break...
-
Performance of a plate heat exchanger operated with water-Al2O3 nanofluid
PublikacjaThis study is focused on experimental investigation of a selected type of brazed plate heat exchanger (PHEx). The main aim of the paper was to experimentally check the ability of nanofluids to enhance the performance of PHEx. A typical water-Al2O3 nanofluid was tested and compared to that of the base fluid, i.e. water. Nanoparticles were tested at the concentration of 0.1% and 1% by weight. Impact of the 1 day and 3 days break...
-
Performance of a plate heat exchanger operated with water-Al2O3 nanofluid
PublikacjaThis study is focused on experimental investigation of a selected type of brazed plate heat exchanger (PHEx). The main aim of the paper was to experimentally check the ability of nanofluids to enhance the performance of PHEx. A typical water-Al2O3 nanofluid was tested and compared to that of the base fluid, i.e. water. Nanoparticles were tested at the concentration of 0.1% and 1% by weight. Impact of the 1 day and 3 days break...
-
Effect of Flow Normalization in Micro-Pin-Finned Heat Sink: Numerical Study
PublikacjaThe micro-pin-fin heat sink (MPFHS) is widely employed for the heat transfer enhancement of microchannel heat sinks. In the current paper, the effect of flow normalization on the thermohydraulic performance of micro-pin-finned heat sinks is studied numerically. Two geometries of MPFHSs, the conventional design micro-pin-fin heat sink (CD-MPFHS) with a uniform-width micro pin fin and the proposed design micro-pin-fin heat sink (PD-MPFHS)...
-
Optimization of the distance between the vertical plates in the convective air heat exchanger
PublikacjaThis paper examines the influence of the distance between vertical plates on the intensity of free convective heat transfer along with the optimization of this distance. Experimental tests were carried out for one model channel of such an heat exchanger with widths , 0.085 and 0.18 m. This channel, open at the top and sides, was formed by two isothermal symmetrically heated parallel vertical plates of dimensions m and m. The influence...
-
Evaluating the influence of radiative heat flux on convective heat transfer from a vertical plate in air using an improved heating plate
PublikacjaThis article examines the influence of radiative heat flux on the accuracy of the results of free convective heat transfer in air. In order to carry out these tests, based on the experience gained during the operation of a plate heated on one side, compensated by a reverse heat loss flux counter-heater, a unique double-sided heating sandwich plate was designed and built, consisting of three thin epoxy resin plates reinforced with...
-
Numerical analysis of high temperature minichannel heat exchanger for recuperative microturbine system
PublikacjaConsidering the development of energy sector, distributed small-scale power generation, e.g., gas micro-CHP, is attracting considerable interest. In such installations, the heat exchanger is one of the key components possessing a significant influence on overall performance. Most studies concentrate on units operating below 900C, which do not fulfil the requirements of gas micro-CHP. Therefore, there remains a challenge to design...
-
Effect of tube bundle arrangement on performance of shell-and-tube latent heat storage system
PublikacjaThis work presents the results of experimental investigation on charging and discharging of latent heat storage systems (LHSS) in the form of shell-and-tube heat exchangers with a variable arrays of the tube bundles. The tests included two tube arrangements – in-line and triangular (staggered), a variable number of tubes in a bundle, two pitch ratios, and different tube positions in a bundle. Three commercial products (LTP56, RT54HC,...
-
Recent advances of selected passive heat transfer intensification methods for phase change material-based latent heat energy storage units: A review
PublikacjaThe following article overviews recent studies regarding heat transfer enhancement methods, explicitly focusing on fins and coils utilization, in phase change material-based latent heat thermal energy storage systems. It discusses the influence of various geometrical and material parameters on the melting and solidification processes, as well as the orientation of the heat transfer surface within the storage tank. Additionally,...
-
Modelling of heat transfer in supercritical pressure recuperators
PublikacjaIn the paper presented is analysis of convective flow heat transfer at supercritical pressure in channels of heat exchanger working in the thermodynamic cycle. The modelling is based on the division of the flow into three regions, namely the heavy fluid, a two phase flow consisting of the heavy and light fluids and finally the light fluid flow. Modelling is concentrated on the region of simultaneous flow of two fluids divided into...
-
Co-simulation strategy of transient CFD and heat transfer in building thermal envelope based on calibrated heat transfer coefficients
PublikacjaThe paper presents a strategy to develop a fully transient numerical model of a heat transfer in building, using a transient CFD model of indoor air and a thermal envelope model, running in a co-simulation. The strategy relies on the utilization of RANS with a high-Re turbulence model and a wall function, which enables to use a coarse computational mesh limiting the computational time. Since wall functions give invalid heat transfer...
-
Heat transfer of two-interacting microjets
PublikacjaThe present paper paid particular attention to the flow and heat transfer performance for two microjets impinging upon the heated surface by means of experimental investigations.
-
Selected studies of flow maldistribution in a minichannel plate heat exchanger
PublikacjaAnalysis of the state of-the-art in research of minichannel heat exchangers, especially on the topic of flow maldistribution in multiple channels, has been accomplished. Studies on minichannel plate heat exchanger with 51 parallel minichannels with four hydraulic diameters, i.e., 461 μm, 574 μm, 667 μm, and 750 μm have been presented. Flow at the instance of filling the microchannel with water at low flow rates has been visualized. The...
-
Effect of Temperature and Nanoparticle Concentration on Free Convective Heat Transfer of Nanofluids
PublikacjaA theoretical analysis of the influence of temperature and nanoparticle concentration on free convection heat transfer from a horizontal tube immersed in an unbounded nanofluid was presented. The Nusselt (Nu) number and heat transfer coefficient were parameters of the intensity of the convective heat transfer. For free convection, the Nu number was a function of the Rayleigh (Ra) number and Prandtl (Pr) number. The Rayleigh (Ra)...
-
Possibilities of heat transfer augmentation in heat exchangers with minichannels for marine applications
PublikacjaIn the paper, new trends in development of microchannel heat exchangers are presented. The exchangers developed in this way can be applied in marine applications. Main attention was focused on heat exchangers design with reduced size of passages namely based on microchannels. In our opinion future development of high power heat exchangers will be based on networks micro heat exchangers.
-
Possibility of thermal imaging use in studies of natural convection heat transfer on the example of an isothermal vertical plate.
PublikacjaA new method of infrared (IR) camera use in convective heat transfer studies has been presented. Until now, IR cameras were utilized for temperature field visualizations of flat heated surfaces of solid objects only. Because liquids and gasses do not emit radiation in the infrared range of wave lengths, detection of temperature field in the air was conducted with the use of plastic mesh, which, after heating by hot air, emits infrared...
-
Analytical model with non-adiabatic effects for pressure drop and heat transfer during boiling and condensation flows in conventional channels and minichannels
PublikacjaIn the paper a method developed earlier by authors is applied to calculations of pressure drop and heat transfer coefficient for boiling flow and condensation flow with account of non- adiabatic effects for some recent data collected from literature. The first effect, the modification of interface shear stresses in annular flow pattern is considered through incorporation of the so called "blowing parameter". The mechanism of...
-
Theoretical consideration of free convective heat transfer from a round isothermal plate slightly inclined from the vertical
PublikacjaA semi-analytical solution of simplified Navier-Stokes and Fourier-Kirchhoff equations describing free convective heat transfer from a round isothermal surface slightly inclined from the vertical is presented. The solution is based on the assumption, typical for natural convection, that the velocity component normal to the surface is negligibly small in comparison to the tangential one. Next we neglect the nonlinear inertia force...
-
Effect of Tube Bundle Arrangement on the Performance of PCM Heat Storage Units
PublikacjaThe results of comprehensive study on charging and discharging of latent heat storage systems (LHSS) are presented. The multi tube shell-and-tube unit with a variable layouts of the tube bundles are examined. Two tube arrangements – in-line and staggered are tested. A variable number of tubes and different tube positions in a bundle are investigated. Moreover, two pitch ratios are studied. Three commercially available substances...
-
Numerical model for thin liquid film with evaporation and condensation on solid surfaces in systems with conjugated heat transfer
PublikacjaCondensation and evaporation processes from wetted surfaces are of utmost importance in many technological or industrial applications. In many devices such as home-appliances and air conditioning systems just to name a few, condensation and evaporation processes greatly impact their performance and energy efficiency; The physics of these processes is quite complex, involving conjugate heat transfer among solid–liquid film-gaseous...
-
Partition of friction heat between sliding semispaces due to adhesion-deformational heat generation
PublikacjaAnalytical expressions of heat-partition coefficient and contact temperatures for two sliding semispaces with account for adhesion-deformational heat generation and contact heat exchange have been obtained. The rate of deformational heat generation is assumed to decay exponentially with increase of distance from the interface. It has been shown that heat-generation configuration and the intensity of contact heat exchange have impact...
-
Pressure drop related to flow maldistribution in a model minichannel plate heat exchanger
PublikacjaThe paper describes the issues related to the pressure drop that accompanies the phenomenon of maldistribution of working fluid between the channels of a model minichannel plate heat exchanger. The research concerns a single exchanger's plate containing 51 (in every geometry) parallel rectangular minichannels of hydraulic diameters 461 µm, 571 µm, 750 µm and 823 µm. In addition, the more complex geometry has been investigated,...
-
Heat transfer enhancement of modular thermal energy storage unit for reversible heat pump cooperation
PublikacjaThe following article presents experimental comparison research on a hexagonal shelland-tube latent thermal energy storage (TES). Such shape of a shell was deliberately chosen instead of a cylindrical one due to its high modularity and with intent for future applications in automobiles (EV and PHEV) air conditioning systems (HVAC). Two geometries of helical coils, acting as tubes, were studied in this article. One was a simple...
-
Free Convection Heat Transfer from Horizontal Cylinders
PublikacjaThe results of experimental investigation of free convection heat transfer in a rectangular container are presented. The ability of the commonly accepted correlation equations to reproduce present experimental data was tested as well. It was assumed that the examined geometry fulfils the requirement of no-interaction between heated cylinder and bounded surfaces. In order to check this assumption recently published correlation equations...
-
Thermal Analysis Of Hybrid Microchannel-Microjet Heat Exchanger
PublikacjaThe paper presents the numerical investigation of a microjet- microchannel cooling module. In which microjets of water are impinging into the microchannels and forming a liquid film on the impingement surface. Applied technology takes benefits from two very attractive heat removal techniques. When laminar jets are impinging on the surface have a very high kinetic energy at the stagnation point, also in microchannels boundary layer...
-
The low temperature waste heat recovery in drying process of pine wood using micro-jet heat exchanger
PublikacjaThe article presents the influence of the drying medium temperature changes for the relative and absolute moisture content values during pine wood drying. The drying process was conducted at constant atmospheric pressure and with different drying medium (air) temperature levels, respectively: 40oC, 60oC, 80oC, 100oC, and 120oC. In order to develop a method that would enable low temperature drying of solid materials the experiments...
-
Modelling of heat and mass transfer through wooden buildings
PublikacjaThe aim of this review paper is to examine the most recent available studies dealing with theoretical, numerical and experimental aspects related to modelling of heat and mass transfer through wooden buildings. The main thermophysical, mechanical and hygrometric properties of wood are firstly discussed. Then, the basic governing equations of heat and mass transfer phenomena are presented. A detailed description of the physical...
-
Two-phase thermosiphon heat exchanger for heat recovery
PublikacjaW pracy przedstawiono wyniki badań eksperymentalnych dotyczących wpływu geometrii pęku rur, rodzaju powierzni przejmowania ciepła parownika oraz płynu pośredniego na całkowitą wydajność dwufazowego termosyfonowego wymiennika ciepła (DTWC). Badaniu poddano sześć prototypowych DTWC z dwiema podziałkami rur w parowniku, dla trzech rodzajów powierzchni rur parownika oraz z zastosowaniem trzech rodzajów płynów pośrednich. Lepszą wydajność...
-
Influence of nanoparticle concentration on convective heat transfer of water-Al2O3 nanofluids inside horizontal tubes
PublikacjaNanofluids came to be seen as a new generation of coolants, especially in single-phase systems. Conducted experiments indicate that the increase in thermal conductivity is not the only reason for the intensification of heat transfer when using nanofluids. Preliminary results of the experimental investigation of the forced convection heat transfer of water-Al2O3 nanofluids inside stainless steel tube with 8 mm internal diameter...
-
Heat transfer characteristics of hybrid microjet – Microchannel cooling module
PublikacjaThe paper presents experimental investigation of heat transfer intensification in a microjet–microchannel cooling module. Applied technology takes benefits from two very attractive heat removal techniques. When jets are impinging on the surface, they have a very high kinetic energy at the stagnation point, also in microchannels boundary layer is very thin allowing to obtain very high heat fluxes. Main objective of this paper was...
-
Experimental Investigation of Free Convection Heat Transfer from Horizontal Cylinder to Nanofluids
PublikacjaThe results of free convection heat transfer investigation from a horizontal, uniformly heated tube immersed in a nanofluid are presented. Experiments were performed with five base fluids, i.e., ethylene glycol (EG), distilled water (W) and the mixtures of EG and water with the ratios of 60/40, 50/50, 40/60 by volume, so the Rayleigh (Ra) number range was 3 104 Ra 1.3 106 and the Prandtl (Pr) number varied from 4.4 to 176....
-
Heat transfer characteristics of hybrid microjet -microchannel cooling module
PublikacjaThe paper presents the experimental investigation of heat transfer intensification in a microjet- microchannel cooling module. Applied technology takes benefits from two very attractive heat removal techniques. When jets are impinging on the surface, they have a very high kinetic energy at the stagnation point, also in microchannels boundary layer is very thin allowing to obtain very high heat fluxes. Main objective of this paper...
-
Cattaneo–Christov heat flow model for copper–water nanofluid heat transfer under Marangoni convection and slip conditions
PublikacjaThis report is devoted to the study of the flow of MHD nanofluids through a vertical porous plate with a temperature-dependent surface tension using the Cattaneo–Christov heat flow model. The energy equation was formulated using the Cattaneo–Christov heat flux model instead of Fourier’s law of heat conduction. The Tiwari–Das model was used to take into account the concentration of nanoparticles when constructing the momentum equation....
-
Hydrodynamics and heat transfer in bubbly flow in the turbulent boundarylayer
PublikacjaW pracy przedstawiono oryginalne podejście do modelowania przepływu pęcherzykowego w warstwie przyściennej i w kanale. Podejście oparte jest na sumowaniu energii dyssypacji pochodzącej od przepływu ścinającego w kanale oraz dyssypacji pochodzącej od obecności pęcherzyków. W wyniku otrzymuje się naprężenia styczne ekwiwalentnego przepływu jednofazowego. Zaproponowano własne podejście do modelowania stopnia zapełnienia opisane równaniem...
-
Modeling of Passive and Forced Convection Heat Transfer in Channels with Rib Turbulators
PublikacjaThe main goal of the research presented in this paper was the experimental and numerical analysis of heat enhancement and aerodynamic phenomena during air flow in a channel equipped with flow turbulators in the form of properly configured ribs. The use of ribs intensifies the heat transfer and at the same time increases not only the flow resistance but also the energy costs. Therefore, designing modern heat exchangers with optimal...
-
Channel Blockage and Flow Maldistribution during Unsteady Flow in a Model Microchannel Plate heat Exchanger
PublikacjaThis paper describes the problem of channel blockage as a result of flow maldistribution between the channels of a model mini channel plate heat exchanger consisting of one pass on each leg. Each leg of the heat exchanger contains 51 parallel and rectangular minichannels of four hydraulic diameters namely 461 μm, 571 μm, 750 μm and 823 μm. In addition, a more complex geometry has been investigated where for the sake of breaking...
-
Numerical investigation of conjugate heat transfer in the presence of two fluid separated by a rigid wall
Publikacja -
Influence of nanoparticle concentration on convective heat transfer of water-Al2O3 nanofluids inside horizontal tubes
PublikacjaThis work presents preliminary results of the experimental investigation of the forced convection heat transfer of water-Al2O3 nanofluids inside stainless steel tube with 8 mm internal diameter and 2000 mm length. Nanoparticles were tested at the concentrations of 0.01%, 0.1%, 1% and 5% by weight and the Reynolds number range encompasses laminar as well as turbulent flows.
-
Impact of Temperature and Nanoparticle Concentration on Turbulent Forced Convective Heat Transfer of Nanofluids
PublikacjaTheoretical analysis of the influence of nanoparticles and temperature on the average Nusselt (Nu) number and the average heat transfer coefficient (HTC) during the turbulent flow of nanofluid in a horizontal, round tube was carried out. The Nu number is a function of the Reynolds (Re) number and the Prandtl (Pr) number, which in turn are functions of the thermophysical properties of the liquid and the flow conditions. On the other...
-
Study of free convective heat transfer from horizontal conic.
PublikacjaPrzedstawiono teoretyczne rozważania i badania eksperymentalne konwekcji swobodnej od izotermicznej powierzchni poziomego stożka w przestrzeni nieograniczonej. Rozwiązanie przeprowadzono dla wprowadzonego krzywoliniowego układu współrzędnych, opartego na krzywej linii prądu wokół powierzchni stożkowej.
-
Monitoring Regenerative Heat Exchanger in Steam Power Plant by Making Use of the Recurrent Neural Network
PublikacjaArtificial Intelligence algorithms are being increasingly used in industrial applications. Their important function is to support operation of diagnostic systems. This paper pesents a new approach to the monitoring of a regenerative heat exchanger in a steam power plant, which is based on a specific use of the Recurrent Neural Network (RNN). The proposed approach was tested using real data. This approach can be easily adapted to...