Wyszukiwarka
Filtry
wszystkich: 1405
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: MINICHANNEL HEAT EXCHANGER
-
Ireneusz Kreja dr hab. inż.
OsobyAbsolwent klasy matematycznej I Liceum Ogólnokształcącego w Gdańsku im. Mikołaja Kopernika (1974). Absolwent Wydziału Budownictwa Lądowego Politechniki Gdańskiej (1979). Od 1979 pracuje na PG. W 1989 uzyskał doktorat (z wyróżnieniem), na Wydziale Budownictwa Lądowego, a w 2008 habilitował się (również z wyróżnieniem) na Wydziale Inżynierii Lądowej i Środowiska PG. Od 2011 jest profesorem PG. Na Politechnice Gdańskiej pełnił funkcje:...
-
MOŻLIWOŚĆ WYKORZYSTANIA ELEKTROWNI JĄDROWEJ JAKO ŹRÓDŁA ENERGII ELEKTRYCZNEJ I CIEPLNEJ
PublikacjaW niniejszym artykule przedstawiono zagadnienia związane z możliwością pracy elektrowni jądrowej (EJ) również w charakterze źródła ciepła, a więc w warunkach skojarzonego wytwarzania energii elektrycznej oraz ciepła. Rozpatrzono dwa poziomy mocy cieplnych oddawanych do systemów ciepłowniczych. Przeprowadzone wstępnie badania techniczne i ekonomiczne dla lokalizacji elektrowni jądrowej nad Jeziorem Żarnowieckim potwierdziły potencjalną...
-
Bead-on-plate welding on S235JR steel by underwater local dry chamber process
PublikacjaThe article presents the results of the effect of parameters of underwater local dry chamber welding on the properties of padding welds. The effect of heat input and the type of shielding gas on the structure and hardness of welds was established. the functions for estimating the maximum hardness of the heat affected zone have been also elaborated.
-
Phase Change Thermal Energy Storage – The Experience of the Materials Preparation for the Specific Applications.
PublikacjaThermal energy storage and temperature stabilization is very important in many engineering applications. There are three kinds of thermal energy storage: sensible heat storage, latent heat storage and reversible chemical reaction heat storage. Phase change materials (PCM) absorb, store and release large amounts of energy in the form of latent heat, at constant temperature, called the transition temperature. The amount of heat...
-
Total electrical conductivity data of (Cr,Fe,Mn,Co,Ni)3O4 High-entropy spinel oxide thin films deposited on amorphous SiO2 substrate by spray pyrolysis techniqe
Dane BadawczeThis dataset includes electrical conductivity measurements results measured by van der pauw technique up to 900oC.
-
The Effects of Pin Profile on HDPE Thermomechanical Phenomena during FSW
PublikacjaFriction stir welding (FSW) of polymeric materials has recently attracted significant attention. Herein, we present the effect of the tool pin profile on the FSW of high-density polyethylene (HDPE) joints through joint experimental analysis and thermomechanical simulations. For analysis of pin profile effects on the thermomechanical properties of HDPE joints, frustum (FPT), cubic (CPT), and triangular (TPT) pin shapes were selected...
-
Nowoczesne metody termochemicznej konwersji biomasy w paliwa gazowe, ciekłe i stałe = Modern methods of thermochemical biomass conversion into gas, liquid and solid fuels
PublikacjaBiomass utilization through direct- or co-combustion with coal, based on coal, hydrogen and oxygen compounds chemical energy conversion into heat in boilers, is simultaneously the cheapest and - according to experts - economically least effective solution. In case of heat and electricity production in cogeneration process in biomass fueled heat and power stations (wood, straw, energetic plants, RDF etc), investment costs are little...
-
The electronic characterization of the cubic Laves-phase superconductor CaRh2
PublikacjaWe present the synthesis and experimental characterization of the electronic properties of the cubic Laves phase superconductor CaRh2. Its crystal structure was confirmed by powder X-ray diffraction and its ambient temperature lattice parameter (a = 7.5326(6) Å) is in good agreement with the literature. Magnetization, resistivity and heat-capacity measurements indicate that CaRh2 is a moderate-coupling type-II superconductor (λe-p = 0.89)...
-
Energy conversion in systems-contained laser irradiated metallic nanoparticles - comparison of results from analytical solutions and numerical methods
PublikacjaThis work introduces the theoretical method of metallic nanoparticles’ (NPs’) heat and mass transfer where the particles are coated on a surface (base), together with considering the case wherein nanoparticles move freely in a pipe. In order to simulate the heat transfer, energy and radiative transfer equations are adjusted to the considered issue. NPs’ properties are determined following the nanofluidic theories, whereas absorption...
-
The topography of strontium–borate glasses and glass-ceramics containing bismuth and vanadium oxides measured with SEM method
Dane BadawczeThe topography of strontium–borate glasses and glass-ceramics containing bismuth and vanadium oxides was measured by SEM.
-
Experimental and numerical analysis of the pyrolysis dynamics of a single wood particle: presentation of the radiographic technique
PublikacjaPyrolysis is an oxygen-free process for the thermal decomposition of raw materials. The heat conduction and flow of pyrolysis products (i.e., the gas fraction and liquid vapour generated during pyrolysis) influence the process and products. In this work, the influence of the orientation of wooden particle fibres with respect to the direction of the heat source on the dynamics of the process was investigated, where there were two...
-
Experimental ORC micro-power plant for CHP application Part A: power plant arrangement
PublikacjaThe co-generative micro-power plant with the HFE7100 applied as a working medium was designed and built for experimental investigations. The heat output of the plant was assumed equal to 20 kW, while the electric output amounted to about 3kW. Examples of the results of the preliminary experimental research on a boiler, heat exchangers, a pump and a turbine-generator set are presented and analysed.
-
Modelling of dryout process in an annular flow
PublikacjaW pracy pokazano teoretyczny model kryzysu wrzenia przy wysokich stopniach suchości, który jest modyfikacją modelu proponowanego wcześniej przez Sedlera i Mikielewicza. Model wysychania filmu cieczowego w przepływie pierścieniowym składa się z różniczkowych równań bilansu masy zapisanych dla filmu na ściance i kropel w rdzeniu przepływu. Rozwiązanie układu równań wymaga znajomości gęstości strumienia masy kropel wytrącających się...
-
Modeling and experimental investigation of the hydraulic jump in liquid film formed by an impinging two-phase air-water jet
PublikacjaPrzedstawiono model analityczny układu hydraulicznego powstałego na skutek uderzenia strugi dwufazowej wody i powietrza. Obliczenia porównano z badaniami eksperymentalnymi przeprowadzonymi na własnym stanowisku badawczym. Uzyskano zadowalającą zgodność.
-
Impact of Silica Nanofluid Deposition on Thermosyphon Performance
Publikacja -
A Computational Analysis of the Aerodynamic and Aeromechanical Behavior of a Thermo-Well for Steam Temperature Measurement in a Steam Turbine
PublikacjaThe goal of the paper is twofold: firstly, it presents computational fluid dynamics analysis for finding maximum unsteady flow forces (and their frequencies) acting on a thermo-well for measuring steam temperature in a steam turbine control stage and secondly, it presents computational solid dynamics analysis of possibility of entry into resonance of the thermowell structure. There have been analyzed two cases of flow with changing...
-
Increase of power and efficiency of the 900 MW supercritical power plant through incorporation of the ORC
PublikacjaThe objective of the paper is to analyse thermodynamical and operational parameters of the supercritical power plant with reference conditions as well as following the introduction of the hybrid system incorporating ORC. In ORC the upper heat source is a stream of hot water from the system of heat recovery having temperature of 90 °C, which is additionally aided by heat from the bleeds of the steam turbine. Thermodynamical analysis...
-
Application of Stirling Engine Type Alpha Powered by the Recovery Energy on Vessels
PublikacjaThe Stirling engine is a device, in which thermal energy is transformed into mechanical without a contact between the heat carrier, and the working gas closed in the engine. Mentioned feature makes this type of engine very attractive for the use of the recovery energy, taken from other heat devices. One of the potential applications of Stirling engines is the use of thermal energy generated in the ship's engine room for producing...
-
Thermal cooling process by nanofluid flowing near stagnating point of expanding surface under induced magnetism force: A computational case study
PublikacjaThis paper is dedicated to the exam of entropy age and research of the effect of mixing nanosolid additives over an extending sheet. In this review, Newtonian nanofluid version turned into researched at the actuated appealing field, heat radiation and variable heat conductivity results. With becoming modifications, the proven PDEs are moved into popular differential situations and paintings mathematically making use of a specific...
-
Maximum transportation growth in energy and solute particles in Prandtl martial across a vertical 3D-heated surface: Simulations achieved using by finite element approach
PublikacjaThe goal of this study is to determine the maximum energy and solute particles' transportation growth in a 3D-heated region of Prandtl martial through a dynamic magnetic field. The effects of this field on the properties of solvent molecules and heat conduction are studied. A correctly stated functional method and a finite element approach are comparable to a certain type of differential equations. In order demonstrate the effects...
-
Thermal energy storage using stearic acid as PCM material
PublikacjaThis work presents an experimental study of thermal energy storage by use of PCM. The aim of the study was to establish the influence of different inlet temperature of heat transfer fluid (HTF) and different Reynolds number of HTF on intensity of charging process. The PCM used in this study was stearic acid and water was used as HTF. A copper helical coil mounted in cylindrical container served as a heat transfer surface.
-
Thermal conductivity of M0-M100 specimens
Dane BadawczeThermal conductivity and volumetric heat capacity values of M0, M20, M40, M60, M80, M100 samples
-
Dilatometry results of SrTi0.50Fe0.50O3-d powder
Dane BadawczeThis dataset contains results of dilatometry measurements of SrTi0.50Fe0.50O3-d powder. The investigation of the linear thermal expansion was carried out using a Netzsch DIL402 dilatometer. The SrTi0.50Fe0.50O3-d powder was formed into cylinders and heat up to 1100 °C with a heating rate of 5 °C min−1, dwelled for 15 min, and then cooled at a rate of...
-
Dilatometry results of SrTi0.65Fe0.35O3-d powder
Dane BadawczeThis dataset contains results of dilatometry measurements of SrTi0.65Fe0.35O3-d powder. The investigation of the linear thermal expansion was carried out using a Netzsch DIL402 dilatometer. The SrTi0.65Fe0.35O3-d powder was formed into cylinders and heat up to 1100 °C with a heating rate of 5 °C min−1, dwelled for 15 min, and then cooled at a rate of...
-
Dilatometry results of SrTi0.30Fe0.70O3-d powder
Dane BadawczeThis dataset contains results of dilatometry measurements of SrTi0.30Fe0.70O3-d powder. The investigation of the linear thermal expansion was carried out using a Netzsch DIL402 dilatometer. The SrTi0.30Fe0.70O3-d powder was formed into cylinders and heat up to 1100 °C with a heating rate of 5 °C min−1, dwelled for 15 min, and then cooled at a rate of...
-
Pin Angle Thermal Effects on Friction Stir Welding of AA5058 Aluminum Alloy: CFD Simulation and Experimental Validation
PublikacjaThe friction stir welding (FSW) of tool pin geometry plays a critical role in the final properties of the produced joint. The tool pin geometry directly affects the generation of heat and the flow of internal materials during the FSW process. The effects of the FSW tool pin angle on heat generation and internal flow have not been quantitatively investigated in detail. In this manuscript, a validated Computational Fluid Dynamic...
-
Experimental validation of pressure drop models during flow boiling of R134a – effect of flow acceleration and entrainment
PublikacjaA crucial step to assure proficient work of power and process apparatus is their proper design. A wide array of those devices operates within boiling or condensation of the working fluid to benefit from high heat transfer rates. Two-phase flows are associated with high heat transfer coefficients because of the latent heat of evaporation and high turbulence level between the liquid and the solid surface. Predicting heat transfer...
-
Flow boiling of R1233zd(E) in a 3 mm vertical tube at moderate and high reduced pressures
PublikacjaThe results of flow boiling of R1233zd(E) in a 3 mm vertical stainless steel tube are presented at moderate and high saturation temperatures. Integral flow characteristics in the form of pressure drop and heat transfer coefficient are discussed for saturation temperatures ranging from 115 to 145 °C (corresponding reduced pressures from 0.2 to 0.7), mass velocity of 800 kg/m2s and heat flux of 20 kW/m2. All of the obtained heat...
-
Alternative cogeneration thermodynamic cycles for domestic ORC
PublikacjaThe Organic Flash Cycle (OFC) is suggested as a vapor power cycle that could potentially improve the efficiency of utilization of the heat source. Low and medium temperature finite thermal sources are considered in the cycle. Additionally the OFC’s aim is to reduce temperature difference during heat addition. The study examines 2 different fluids. Comparisons are drawn between the OFC and an optimized basic Organic Rankine Cycle...
-
ANALYSIS OF TEMPERATURE DISTRIBUTIONS IN A GERMICIDAL CHAM-BER SUPPORTED BY LIGHT-ILLUMINATED GOLD NANORODS USING CFD-EQUATIONS AND A THERMAL CAMERA
PublikacjaSince the COVID-19 pandemic, protection against pathogenic germs and surface disinfection have become critical issues. Most effective bacteria/virus inactivation methods are either power-consuming or require using caustic chemical substances. Herein, thermal inactivation appears to be an affordable and effective technique as long as high temperatures are reached quickly and long-termly maintained. Therefore, the preparation of...
-
Domestic ORC micro-CHP combined with a commercial gas boiler
PublikacjaThe chapter presents the results of experimental studies conducted during the launch of the first in Poland demonstration prototype of the micro ORC coupled to a domestic gas boiler. The accomplished studies indicated the possibility for the ORC module to work with such boiler (autonomous source of heat) with a prototype single-stage axial micro turbine as the expansion machine. Confirmation of that fact has been delineated in...
-
Turbulence models impact on the flow and thermal analyses of jet impingement
PublikacjaAccurate numerical reconstruction of heat and mass transfer processes in particular applications, such a jet impingement, is difficult to obtain even with the use of modern computational methods. In the proposed paper, the flow and thermal phenomena occurring during single minijet impingement on the flat, concave and convex, heated surfaces were considered. Problem of impingement on non-flat surface, still not common and purely...
-
Possibility to use engine compression ignition engines in floating power plants marine
PublikacjaCompression-ignition engines used in ship technology as main propulsion engines are large units reaching even to 50-60 MW. The engines can be used in power industry for electricity generation in a simple or combined steam turbine system in combined heat and power plants. The leading engine in such an arrangement is an internal-combustion piston engine. The main propulsion engines are used in large piston internal-combustion engines...
-
Feasibility of combined diesel engine - steam turbine in power station operating in the maritime
PublikacjaCompression-ignition engines used in ship technology as main propulsion engines are large units reaching even to 50-60 MW. Currently, the efficiency of such engines amounts to 45-50%. With such a large power unit, exhaust gases leaving the engine contain very large quantities of heat available for further treatment. Exhaust gases from the piston engine contain about 25% of the heat supplied to the engine in the fuel. Using the...
-
The effect of heating and fermenting on antioxidant properties of white cabbage
PublikacjaIt is widely believed that natural antioxidants found in food are significantly lost during processing. Nevertheless, it was recently demonstrated that processed fruits and vegetables may retain their antioxidant activity. In the present work, the changes in the overall antioxidant properties as a consequence of fermentation of cabbage and/or heat treatment of cabbage juices and extracts were studied. Fermentation processes as...
-
Application of Thermo-chemical Technologies for Conversion of Associated Gas in Diesel-Gas Turbine Installations for Oil and Gas Floating Units
PublikacjaThe paper considers the issue of thermo-chemical recovery of engine’s waste heat and its further use for steam conversion of the associated gas for oil and gas floating units. The characteristics of the associated gas are presented, and problems of its application in dual-fuel medium-speed internal combustion engines are discussed. Various variants of combined diesel-gas turbine power plant with thermo-chemical heat recovery are...
-
A pore-scale thermo–hydro-mechanical model for particulate systems
PublikacjaA pore scale numerical method dedicated to the simulation of heat transfer and associated thermo–hydro-mechanical couplings in granular media is described. The proposed thermo–hydro-mechanical approach builds on an existing hydromechanical model that employs the discrete element method for simulating the mechanical behavior of dense sphere packings and combines it with the finite volume method for simulating pore space fluid flow...
-
Kinetics of Intermetallic Phase Precipitation in Manual Metal Arc Welded Duplex Stainless Steels
PublikacjaThe article presents the influence of heat treatment on the kinetics of transformations in lean duplex LDX2101 steel and a weld made of standard duplex 2209 material, which was welded by manual metal arc welding. Changes in the microstructure, hardness, and magnetic phase content were analyzed after heat treatment was conducted at a temperature of 800 °C for a period ranging from 15 to 1440 min. Light and scanning microscopy, Vickers...
-
BET of TiO2 heated at 400-600 C degrees
Dane BadawczeThese data refer to the results of BET surface area of TiO2, which was treated firstly in autoclave at 150 C degrees for 1h (sample marked as A150), then was further heat treated in Ar or H2 at 400-600 C degrees. As a raw material TiO2 was used, which was a semiproduct from the industrial production of titania white by sulphur method. The raw material...
-
The influence of thermal treatment on electrocatalytic properties of Mn-Co nanofilms on nickel foam toward oxygen evolution reaction activity
PublikacjaThis work evaluates electrodeposited and differently treated Mn-Co catalysts for their oxygen evolution reaction activity. Catalysts are evaluated in the as-deposited and heat treated state: after 350 C and 600 C. Results show that the highest electrochemical activity is obtained for the as-deposited Mn-Co oxyhydroxide, which possibly possess a layered double hydroxide structure. After the heat treatment process, especially after...
-
Mechanical and structural behavior of high-strength low-alloy steel pad welded by underwater wet welding conditions
PublikacjaThe aim of the paper was to determine the metallurgical and mechanical behaviors of a high-strength low-alloy (HSLA) steel pad-welded specimen used in the structures of industrial and naval parts. Then to predict the metallurgical consequences (nature of the phases present) and the mechanical properties (hardness and impact strength) of the pad-welded steel obtained by underwater wet welding with different heat input values. The...
-
Effects of Noncontact Shoulder Tool Velocities on Friction Stir Joining of Polyamide 6 (PA6)
PublikacjaIn this study, the effects of the traverse and rotational velocities of the noncontact shoulder tool on the heat generation and heated flux during the friction stir joining of high-density polyamide 6 (PA6) polymer were investigated. The computational fluid dynamics (CFD) method was employed to simulate the thermomechanical phenomena during the friction stir joining (FSJ) process of PA6. A developed model was used to consider the...
-
Dilatometry results of SrxTi0.30Fe0.70O3-d materials
Dane BadawczeThis dataset contains results of dilatometry measurements of SrxTi0.30Fe0.70O3-d (x=0.90, 0.95, 1.00 and 1.05) materials. The investigation of the linear thermal expansion was carried out using a Netzsch DIL402 dilatometer. The SrxTi0.30Fe0.70O3-d powder was formed into cylinders and heat up to 1100 °C with a heating rate of 5 °C min−1, dwelled for...
-
The experimental results of sorption cycles
Dane BadawczeExperimental studies of sorption cycles were carried out using a prototype research stand, which is a laboratory-scale model of an adsorption chiller. The Intensified Heat Transfer Adsorption Bed (IHTAB) reactor is adapted to the analysis and optimization of various parameters of adsorption systems, e.g., constructions and compositions of adsorption...
-
Comparative study of flow condensation in conventional and small diameter tubes
PublikacjaFlow boiling and flow condensation are often regarded as two opposite or symmetrical phenomena, however their description with a single correlation has yet to be suggested. In the case of flow boiling in minichannels there is mostly encountered the annular flow structure, where the bubble generation is not present. Similar picture holds for the case of inside tube condensation, where annular flow structure predominates. In such...
-
Experimental Investigations of Forced Convection of Nanofluids in Smooth, Horizontal, Round Tubes: A Review
PublikacjaA comprehensive review of published works dealing with experimental studies of forced convection heat transfer of nanofluids is presented. The survey is limited to straight, smooth, and round tubes. Moreover, only mono nanofluids exhibiting Newtonian behaviour are considered. Works on experimental research of forced convection in tubes are presented in a chronological order in the first part of the article. In this part, attention...
-
Effects of FSW Tool Plunge Depth on Properties of an Al-Mg-Si Alloy T-Joint: Thermomechanical Modeling and Experimental Evaluation
PublikacjaOne of the main challenging issues in friction stir welding (FSW) of stiffened structures is maximizing skin and flange mixing. Among the various parameters in FSW that can affect the quality of mixing between skin and flange is tool plunge depth (TPD). In this research, the effects of TPD during FSW of an Al-Mg-Si alloy T-joint are investigated. The computational fluid dynamics (CFD) method can help understand TPD effects on FSW...
-
Storing thermal energy from solar collectors for the needs of a detached house
PublikacjaThis work evaluates the possibility of meeting a single familu household's need for hot water and heat year round, using solar collectors as the sole energy sourse. The main flaw of energetic systems based on solar energy is that the energy supply is usually insufficient in winter, when it is most needed. This work is going to show thatm for a house surface of 150 m2 and base dimension of 10x10m, it is possible to supply sufficient...
-
Control of a vapour microturbine set in cogeneration applications
PublikacjaSystems with microturbines are implemented for local generation of heat and electricity. This paper presents the analysis of control concepts for a vapour microturbine set with a generator with permanent magnets, intended to work in small heat and power plants. Control system variants differed by the selection of controlled signals and set parameters. Possible ways of control were discussed and compared with experimentally determined...
-
Low temperature rotary Stirling engine: conceptual design and theoretical analysis
PublikacjaThe use of low-temperature energy sources for electricity generation demands a dual focus: a substantial enhancement in the efficiency of energy conversion devices and a reduction in system production costs. Particularly in scenarios where low-temperature energy sources are scarce, this factor can be pivotal in facilitating widespread adoption of such technologies. The Stirling engine emerges as a promising solution capable of...