Wyszukiwarka
Wyniki wyszukiwania dla: fuels
-
Pyrolysis Process of Whole Waste Tires as a Biomass Energy Recycling
PublikacjaThe article is devoted to the description of material recycling of whole waste tires, including a new method of pyrolysis process, resulting in the final products: technically oil fractions (rubber plasticizer of rubber compounds) or diesel fuels (light, medium and heavy), activated carbon, gas fuel and steel scrap. Operational and performance tests of the first version of the pilot plant, consisting of three contributions cooperating...
-
Gasification of Densified Biomass (DB) and Municipal Solid Wastes (MSW) Using HTA/SG Technology
PublikacjaThe necessity of economical and rational use of natural energy sources caused a rapid development of research on the possibilities of using non‐conventional energy resources. Taking the above into account, a new technological process of thermochemical conversion of biomass and communal waste, commonly known as High Temperature Air/Steam Gasification (HTA/SG) and Multi‐Staged Enthalpy Extraction Technology (HTAG‐MEET), was developed....
-
Production of hydrogen from biomass and its separation using membranetechnology
PublikacjaHydrogen is an important raw material for chemical industry and feasible renewable energy carrier that could replace fossil fuels. However, the specie seldom exists in a form of pure H2. Therefore, to obtain hydrogen in volumes suitable to be used as a raw material it is necesary to decompose hydrogen-rich compounds. The carbohydrate-rich biomass can be an important source of hydrogen by applying the process of dark fermentation....
-
Contaminants in airport runoff water in the Vicinities of Two International Airports in Poland
PublikacjaThe general aim of the study was to evaluate environmental quality associated with the operations (combustion of fuels, cleaning of aircraft and airport aprons, aircraft, ground vehicle maintenance and repairs, fuelling operations, de/anti-icing operations) of international airports located in central and northern of Poland. These two monitoring areas were set up to monitor PAHs, PCBs, formaldehydes, phenols, detergents (cationic,...
-
Conversion of Biomass and Municipal Wastes into Syngas and Hydrogen using Highly Preheated Agent (HTAG)
PublikacjaGasification is considered to be one of the most promising energy recovery technologies for the widespread utilization of biomass and wastes. During this process raw feedstock is converted into a combustible gas, which can then be burnt to produce thermal energy, or to run engines for mechanical or electrical power. The studies of biomass gasification demonstrate it as a friendly alternative to fossil fuels as one of renewable...
-
Disruption of the communication process on the example of ALEP-PL web application
PublikacjaBy creating a dedicated web service, such as the presented ALEP-PL solution, you can not assume that its users have suffcient knowledge of the energy sector. This application is dedicated to the local energy planning. The ALEP-PL makes it easier to incorporate in the planning of key players in the local energy market. This group of ALEP-PL users represents mainly the ocials of energy companies and specialist offcers. In the paper...
-
ECU calibration for gaseous dual fuel supply system in compression ignition engines
PublikacjaThe dual fuel (DF) combustion mode is proven solution that allows to improve or get at the same level engine performance and reduce toxic compounds in exhaust gases which is confirmed by researchers and end-users. DF combustion mode uses two fuels gaseous fuel as a primary energy source and a pilot quantity of diesel fuel as ignition source. However, in order, to fully take advantage of the potential of the dual fuel mode, DF system...
-
Risks caused by microbiologically influenced corrosion in diesel fuel storage tanks
PublikacjaMicrobiologically influenced corrosion (MIC) poses serious problems for the petrochemical and refinery industries. Particularly favourable conditions for MIC arise in storage tanks and transmission pipelines for mixtures of diesel oil with the addition of a biocomponent (in Poland 7%). The best conditions for the development of MIC occur at the fuel-water interface, where microorganisms are provided with a source of food and water,...
-
Comparative study of a combined heat and power plant retrofitted by CO2 capture during the combustion of syngas from sewage sludge gasification versus zero-emission combustion of hydrogen produced using renewables
PublikacjaWith ecological requirements aimed at limiting the production of CO2, it is necessary to produce all, or most of the energy from RES. During the transformation process, ecological and highly efficient combustion power plants will be needed. The classic cycle of combined heat and power (CCGT) with green improvements will continue to be one of the most suitable technologies for this task. This article presents the modernization of...
-
Improvement of CO2 absorption and inhibition of NH3 escape during CaCO3 precipitation in the presence of selected alcohols and polyols
PublikacjaThis research aims to investigate the effect of selected organic substances containing hydroxyl groups on the reduction of NH3 escape and the improvement of CO2 capture during the precipitation of calcium carbonate by carbonation method using post-distillation liquid from the Solvay process and gas stream containing CO2 in the amount corresponding to the exhausted gases produced by the combustion of fossil fuels. Glycerol, ethylene...
-
Conception for diagnosing SI engines fed with biofuel in operation conditions
PublikacjaThe article deals with the question of diagnosing the high power self ignition (SI) engines fed with pro-ecologic fuels in an aspect of appearing operation problems. There has been presented the specific of action and techno-operation profile of the combustion engine foreseen as an investigations object. The preliminary conception of diagnostic investigations of the engine 7L35MC type produced in H. Cegielski - Poznan S.A. factory...
-
Performance of microbial fuel cells operated under anoxic conditions
PublikacjaNowadays, microbial fuel cells (MFC) stand up as a promising renewable energy source. Due to the ability of the MFC to oxidize a wide spectrum of substrates, wastewater seems to be one of the most interesting fuels. Unfortunately, wastewater could contain electron acceptors such as nitrate, which could interfere with the electrical performance of the MFC. In this work, the influence of oxidised nitrogen forms on the electricity...
-
Potential applications of crude glycerol in polymer technology–Current state and perspectives
PublikacjaThe increasing use of bio-based fuels and fuel additives, among them biodiesel, causes significant surplus of crude glycerol on the market which creates new challenges in terms of its sustainable utilization. A lot of ways for the incorporation of this by-product into different branches of industry requires purification by expensive and complicated processes. Therefore, researchers are seeking for applications of untreated crude...
-
Selected Aspects of Biofuels Market and the Electromobility Development in Poland: Current Trends and Forecasting Changes
PublikacjaThis work presents basic information associated with markets of selected alternative fuels used in transport, such as methyl esters, conventional bioethanol and lignocellulosic bioethanol, and the market of electrical vehicles. Legal conditions, which stimulate development and regulate the mode of functioning of the liquid biofuel market until 2020 are discussed, based on provisions of EU directives. Data on biofuel production...
-
Methods of liquid biofuels production - the bioethanol example.
PublikacjaEthanol is used in chemical and food industry, mainly either in the synthesis or as a solvent. The newest application of ethanol is as a fuel. This alcohol, produced on an industrial scale from crop waste, is widely known under the name bioethanol. It could be used as a fuel by itself or in a mixture with gasoline. Today, there are several technologies for bioethanol production known. The relatively simple method of obtaining bioethanol...
-
METHODS OF LIQUID BIOFUEL PRODUCTION – THE BIOETHANOL EXAMPLE
PublikacjaEthanol is used in chemical and food industry, mainly either in the synthesis or as a solvent. The newest application of ethanol is as a fuel. This alcohol, produced on an industrial scale from crop waste, is widely known under the name bioethanol. It could be used as a fuel by itself or in a mixture with gasoline. Today, there are several technologies for bioethanol production known. The relatively simple method of obtaining bioethanol...
-
Export diversification and dependence on natural resources
PublikacjaLow export diversification is a risk-augmenting factor for many countries dependent on natural resources. The literature tends to focus on the growth effects of resource dependence (‘resource curse’ debate) while not much is known on how it affects the variety of non-resource exports. To quantify this effect we decompose the relative Theil index using product-level export data from 160 countries over the time period 1996–2018....
-
Analiza przestrzenna sprzedaży paliw
PublikacjaZe względu na zmieniające się warunki i niepewność ekonomiczną gospodarowania, przeprowadzane badania dotyczące popytu na paliwa płynne dotyczą głównie zmian popytu w czasie, rzadziej w przestrzeni. Jednak rozwój narzędzi ekonometrycznych, który dokonał się w latach dziewięćdziesiątych, umożliwił nie tylko badania zmian popytu wynikające ze związków przyczynowo-skutkowych zachodzących w czasie, ale również w przestrzeni oraz w...
-
A model of fuel combustion process in the marine reciprocating engine work space taking into account load and wear of crankshaft-piston assembly and the theory of semi-Markov processes
PublikacjaThe ar ticle analyses the operation of reciprocal internal combu stion engines, with mar ine engines u sed a s an example. The analysis takes into account types of energy conversion in the work spaces (cylinders) of these engines, loads of their crankshaft-piston assemblies, and types of fuel combustion which can take place in these spaces during engine operation. It is highlighted that the analysed time-dependent loads of marine...
-
Pretreatment of Lignocellulosic Materials as Substrates for Fermentation Processes
PublikacjaLignocellulosic biomass is an abundant and renewable resource that potentially contains large amounts of energy. It is an interesting alternative for fossil fuels, allowing the production of biofuels and other organic compounds. In this paper, a review devoted to the processing of lignocellulosic materials as substrates for fermentation processes is presented. The review focuses on physical, chemical, physicochemical, enzymatic,...
-
Recuperator with microjet technology as a proposal for heat recovery from low-temperature sources
PublikacjaA tendency to increase the importance of so called dispersed generation, based on the local energy sources and the working systems uti- lizing both the fossil fuels and the renewable energy resources is observed nowadays. Generation of electricity on industrial or domestic scale together with production of heat can be obtained for example through employment of the ORC systems. It is mentioned in the EU directive 2012/27/EU for...
-
Sustainable bioethanol production from first- and second-generation sugar-based feedstocks: Advanced bibliometric analysis
PublikacjaBioethanol is produced from carbohydrate-containing feedstocks through fermentation. Based on a bibliometric review of studies published between 2012 and 2021, we analyzed those on sustainable bioethanol production. The Web of Science main collection yielded 1647 publications, which were analyzed using VOSViewer, CiteSpace, and ArcMap software. More than half of these publications originated from some Asian countries, corresponding to...
-
VOCs absorption from gas streams using deep eutectic solvents – A review
PublikacjaVolatile organic compounds (VOCs) are one of the most severe atmospheric pollutants. They are mainly emitted into the atmosphere from anthropogenic sources such as automobile exhaust, incomplete fuel combustion, and various industrial processes. VOCs not only cause hazards to human health or the environment but also adversely affect industrial installation components due to their specific properties, i.e., corrosive and reactivity....
-
Influence of Rock Dust Additives as Fine Aggregate Replacement on Properties of Cement Composites—A Review
PublikacjaConcrete production consumes enormous amounts of fossil fuels, raw materials, and is energy intensive. Therefore, scientific research is being conducted worldwide regarding the possibility of using by-products in the production of concrete. The objective is not only to identify substitutes for cement clinker, but also to identify materials that can be used as aggregate in mortar and concrete productions. Among the potential alternative...
-
Regulacje prawne odnoszące się do testowania samochodów autonomicznych na drogach publicznych w Polsce i w Kalifornii
PublikacjaThe current level of technological advancement allows for predicting that in the near future autonomous technology may be successfully used for the production of self-driving cars. Many companies (not necessarily related to the automotive sector) have spotted the chance of future profits and thus started working on testing and development of autonomous vehicles. The initiation of work has indicated the lack of possibility to test...
-
Gas Turbine Cycle with External Combustion Chamber for Prosumer and Distributed Energy Systems
PublikacjaThe use of various biofuels, usually of relatively small Lower Heating Value (LHV), affects the gas turbine efficiency. The present paper shows that applying the proposed air by-pass system of the combustor at the turbine exit causes tan increase of efficiency of the turbine cycle increased by a few points. This solution appears very promising also in combined gas/steam turbine power plants. The comparison of a turbine set operating...
-
TEST FOR ASSESSING THE ENERGY EFFICIENCY OF VEHICLES WITH INTERNAL COMBUSTION ENGINES
PublikacjaThe most popular method for assessing the energy efficiency of vehicles is to compare the fuel consumption achieved in the conditions of selected approval test. Operating conditions are defined using the speed profiles, usually for only two categories: urban and extra-urban driving. Assessing the energy efficiency of vehicles should be performed using a more detailed classification of conditions. Presented results of comparison...
-
Effect of selected ammonia escape inhibitors on carbon dioxide capture and utilization via calcium carbonate precipitation
PublikacjaCarbon dioxide was used to precipitate CaCO3 with CaCl2 solution in the presence of NH3 as a CO2 absorption promoter. Compounds that were previously indicated as inhibitors of ammonia escape during CO2 absorption were also added to the reaction mixture. Inorganic salts, i.e. ZnCl2, CuCl2, CoCl2, and organic substances, i.e. glycerol, ethylene glycol and triethanolamine were tested inhibitors in this work. A model post-distillation...
-
Relevance of the EU Structural Funds’ Allocation to the Needs of Combating Air Pollution in Poland. Analysis of the Operational Programmes of Regions Threatened With Critical Air Pollution from Distributed Energy Sources
PublikacjaRecent years, the European Environmental Agency, has been reporting air quality parameters in Poland, as the poorest among all the EU countries. Despite of adoption of the EU legislation on energy efficiency and energy performance of buildings, existing legal solutions occur insufficient in reducing air pollution in Polish regions. Lack of an effective schemes supporting complex thermal renovation of buildings, exchange of inefficient...
-
Computer -Aided Local Energy Planning Using ALEP-PL Software
PublikacjaThe issue of energy system planning, including the planning of local energy systems, is critical, since it affects the security of energy supplies in communities, regions, and consequently the security of energy supply within the country. Energy planning is a complex process that requires integration of different goals i.e. improvement of energy efficiency, increase in the share of renewables in the energy balance and CO2} emission...
-
Recuperator with microjet technology as a proposal for heat recovery from low-temperature sources
PublikacjaA tendency to increase the importance of so called dispersed generation, based on the local energy sources and the working systems utilizing both the fossil fuels and the renewable energy resources is observed nowadays. Generation of electricity on industrial or domestic scale together with production of heat can be obtained for example through employment of the ORC systems. It is mentioned in the EU directive 2012/27/EU for cogenerative...
-
Experimental investigation of performance and emission characteristics of a miniature gas turbine supplied by blends of kerosene and waste tyre pyrolysis oil
PublikacjaFossil fuels are non-renewable sources of energy that could be depleted in the near future, giving rise to amajor energy crisis. Scientists from all over the world are working on new technologies to produce fuelnot only from renewable sources but also from waste. This article is concerned with: (i) waste tyremanagement by means of the pyrolysis process, (ii) investigation of physico-chemical parameters ofwaste tyre pyrolysis oil...
-
External Security Strategies of Belarus
PublikacjaUnder President Lukashenko, three Belarusian national security strategies have been announced: the first in 1995, the second in 2001 and the third in 2011. The first proposal, formulated after Lukashenko’s victory in the presidential elections in 1994, outlined Belarus as a neutral state, unbound to any military block in the absence of external enemies. The direction of the foreign policy pursued by the president of Belarus was...
-
Market Structure and Market Power in Selected Sectors of The Polish Economy Based on COICOP Classification
PublikacjaThis paper present new and simple measures of market structure and market power. Based on the classical models of market structures, where a given structure is determined by the number of enterprises, indexes of degree of monopoly have been estimated, representing an average number of entities per branch. Additionally, market power indexes have been determined as an average revenue per an enterprise in a given branch. This approach...
-
Investigation of the Combustion Processes in the Gas Turbine Module of an FPSO Operating on Associated Gas Conversion Products
PublikacjaIn this paper, we consider the issue of thermo-chemical heat recovery of waste heat from gas turbine engines for the steam conversion of associated gas for offshore vessels. Current trends in the development of offshore infrastructure are identified, and the composition of power plants for mobile offshore drilling units and FPSO vessels is analyzed. We present the results of a comparison of power-to-volume ratio, power-to-weight...
-
The influence of core material on strength properties of hybrid sandwich panels
PublikacjaAlong with high prices of fuels and more restrictive safety and environmental regulations (including environment protection) increased interest in sandwich structures is being observed. One of the solution having growing application potential is steel sandwich panel. The construction consist of very thin steel plates (about 2mm) and stiffeners between them. The main advantage of using such solution is very high strength to weight...
-
Comparative Analysis of Carbon, Ecological, and Water Footprints of Polypropylene-Based Composites Filled with Cotton, Jute and Kenaf Fibers
PublikacjaComposites containing natural fibers are considered environmentally friendly materials which is related to the reduced use of fossil fuels and the emission of carbon dioxide compared to petroleum-based polymers. Nevertheless, a complete evaluation of their environmental impact requires a broader view. This paper presents a carbon, ecological, and water footprints assessment of polypropylene-based composites filled with cotton,...
-
Powering the Future by Iron Sulfide Type Material (FexSy) Based Electrochemical Materials for Water Splitting and Energy Storage Applications: A Review
PublikacjaWater electrolysis is among the recent alternatives for generating clean fuels (hydrogen). It is an efficient way to produce pure hydrogen at a rapid pace with no unwanted by-products. Effective and cheap water-splitting electrocatalysts with enhanced activity, specificity, and stability are currently widely studied. In this regard, noble metal-free transition metal-based catalysts are of high interest. Iron sulfide (FeS) is one...
-
Lessons learned during SRAD hybrid motor development
PublikacjaStudent Researched and Developed (SRAD) hybrid rocket motor H-15 with total impulse of 15 $kNs$ was built. First version of the engine has average thrust of 3 $kN$, the second, improved one is prepared with an aim to have average thrust of 5 $kN$. Engine development was started from scratch and went through phases of: definition of design assumptions and constraints, numerical modelling to predict engine performance, CAD and CAM...
-
Mercury concentration in the sediments as a function of changing climate in coastal zone of Southern Baltic Sea – preliminary results
PublikacjaMercury, despite of its many uses in industry, is also highly toxic. It is highly neurotoxic, and because of the ability of mercury to penetrate placental barrier, in some countries ban on predatory fish consumption (the main route of mercury into human organism) by pregnant women was introduced. There are very little publications describing the consequences of weather anomalies on contaminants cycles. No research was published...
-
Multifunctional catalyst-assisted sustainable reformation of lignocellulosic biomass into environmentally friendly biofuel and value-added chemicals
PublikacjaRapid urbanization is increasing the world's energy demand, making it necessary to develop alternative energy sources. These growing energy needs can be met by the efficient energy conversion of biomass, which can be done by various means. The use of effective catalysts to transform different types of biomasses will be a paradigm change on the road to the worldwide goal of economic sustainability and environmental protection. The...
-
ROLE OF GREEN LOGISTICS IN THE CONSTRUCTION OF SUSTAINABLE SUPPLY CHAINS
PublikacjaThe global supply chain has been growing strongly in recent years. This development brings many benefits to the economy, society, and human resources in each country but also causes a large number of concerns related to the environment since traditional logistics activities in the supply chain have been releasing significant amount of emissions. For that reason, many solutions have been proposed to deal with these environmental...
-
Wykorzystanie systemu komputerowego ALEP-PL w planowaniu rozwoju lokalnych systemów energetycznych
PublikacjaZaprezentowano autorski system komputerowy ALEP-PL, który wspomaga proces planowania rozwoju lokalnych systemów energetycznych. Narzędzie zostało przygotowane z uwzględnieniem metodyki planowania zaawansowanego. System składa się z serwisu internetowego, bazy danych i modułów logiki biznesowej. Serwis internetowy został stworzony w technologii ASP.NET z użyciem środowiska Visual Studio 2010 i serwera baz danych MS SQL Server 2008...
-
Possibilities for Developing Electromobility by Using Autonomously Powered Trolleybuses Based on the Example of Gdynia
PublikacjaTrolleybus transport refers to contemporary challenges related to a reduction in emissions of greenhouse gases and CO2 into the atmosphere formulated by international institutions, such as the United Nations, the Organisation for Security and Co-operation in Europe, or the European Union. Departure from fossil fuels in urban transport is one of the key challenges for the coming years. Trolleybuses are an important tool in this...
-
Numerical Study of the Impinging Jets Formed by an Injector with Different Nozzle Diameters
PublikacjaThe collision of two or more liquid jets may provide considerable atomisation and efficient mixing of injected substances at the same time. This phenomenon is used, among others, in rocket engines, where the fuel and oxidiser are introduced separately and almost immediately mixed through self-impingement. Depending on the injection and operating conditions, diverse configurations of impinging jets are used, such as doublets,...
-
From evil demiurge to caring hero: Images of geneticists in the movies
PublikacjaAlthough images of science and scientists depicted in popular culture have been criticized as an exaggeration and fear mongering, the cinema is an important resource that influences individuals’ beliefs about science. Because popular depictions of science play a crucial role in constructing the public’s ‘scientific imaginary’ they constitute an inherent dimension of the social understanding of science and are as important for...
-
RAPESEED PELLET - A BYPRODUCT OF BIODIESEL PRODUCTION - AS AN EXCELLENT RENEWABLE ENERGY SOURCE
PublikacjaVegetable oils are renewable feedstock currently being used for production of biofuels from sustainable biomass resources. The existing technology for producing diesel fuel from plant oils, such as rapeseed, soybean, canola and palm oil are largely centered on transesterification of oils with methanol to produce fatty acid methyl esters (FAME) or biodiesel. Rapeseed pellet - crushed seed residue from oil extraction is a byproduct...
-
Nanobiocatalysis for biofuel production
PublikacjaThe human race is relied on the use of conventional and non-renewable energy resources like fossil fuels for centuries. With the rising environmental issues linked with the use of these conventional energy resources, the trend soon shifted towards more robust and sustainable energy resources. In this regard, the different generations of biofuels have revolutionized the industrial sector by ensuring an eco-friendly and more economical...
-
Battery Technologies in Electric Vehicles: Improvements in Electric Battery Packs
PublikacjaRestrictions on fossil fuels and related environmental pollution issues motivate many organizations and countries to set their focus on electric vehicles (EVs) rather than conventional internal combustion engine vehicles [1], [2]. EVs require an energy storage system to store converted electric power in another form of energy and then reconvert the stored energy to electric power whenever it is required. The energy stored can be...
-
Biowodór, „paliwo przyszłości”, dotychczasowe metody otrzymywania , porównanie metod otrzymywania
PublikacjaWodór jest ważnym pierwiastkiem w przemyśle chemicznym. Biowodór wydaje się być użytecznym odnawialnym nośnikiem energii, który mógłby zastąpić paliwa kopalne. Największym problemem wodoru jest jego rzadkie występowanie w czystej formie molekularnej H 2 . Dlatego otrzymanie biowodoru w objętościach opłacalnych ja ko surowiec czy biopaliwo wiedzie przez bioodpady „przesycone” wodorem. Każdy związek...